experience9 yearsRuslan Ts.
Washing machine and refrigerator repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 746 00 26Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
We'll arrive within 60 minutes anywhere in the city. Free diagnostics.
Our own technicians4 to 20 years of experience




Repair prices
Below are typical symptoms and likely causes. A technician will perform an accurate diagnosis.
refrigerant leak, clogged capillary
from10 500 ₸
defrost sensor, defrost heater, timer
from6 000 ₸
clogged drain, door misalignment
from5 000 ₸
No Frost fan, vibration
from10 500 ₸
code points to a specific component
from9 500 ₸
sensor, board, damper
from6 000 ₸
thermostat, sensor, refrigerant leak
from9 500 ₸
gasket, door misalignment, hinges
from7 500 ₸
The table lists the 'from' price for labor and the time required; the technician confirms the final amount before any repair begins.
1 visittime
from 6 500 ₸cost

BeforeAfter5 steps

From request to performance check — five clear steps.
Leave a request and a technician will arrive within 60 minutes anywhere in the city.
The technician arrives, inspects the refrigerator, and agrees on next steps with you.
You approve the scope of work and when repair starts.
The technician performs the work. You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies.
We check the operation together with you right after repair.
The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsField refrigerator repair technician
experience12 yearsGeneral household appliance repair technician
experience8 yearsExpert washing machine repair technician
We reply during working hours
Leave a request and a technician will come at a convenient time. Ask the technician for any details you need.

Warranty question? Call us
+7 (778) 746 00 267 898 reviews of repairs at TECH SERVICE in total
Ксения И.Order No. TS-2612-282 · 29 August 2026
oursХотел сначала вызвать мастера на дом, потом передумал. Первое, что заметил: намерзает лёд. Никита М взялся за то, от чего другие отказались. Гудит ровно, не греется, всё как надо
Мирас С.Order No. TS-2641 · 13 July 2026
oursПроблема — течёт. Отдельно спосибо мастеру — Никита М, терпения ему хватило. Сделали и забыл про проблему.
Мадина Т.Order No. TS-7219 · 28 November 2024
oursХотел сначала вызвать мастера на дом, потом передумал. Нужен был ремонт холодильника — обратился сюда. С чем пришёл: шумит. Сказали 27 000, а потом ещё и скидку сделали. Приехал вечером, мастер ещё был на месте. Заодно поменяли: термостат. В помещении тесновато, но это мелочи. Внешне как новый, если не считать мелкой царапины!!
Индира П.Order No. ZK-1617 · 20 September 2024
oursХотел сначала вызвать мастера на дом, потом передумал. Техсервис на Абая, если не ошибаюсь, — вот туда и поехал. Проверили на всех режимах, всё чётко!!
Лилия В.Order No. TS-4770 · 30 May 2024
oursРаботаю допоздна, поэтому нужен был сервис с нормальным графиком. Основная жалоба — намерзает лёд. Проверили при мне, показали, что всё держит.
Аружан К.Order No. ZK-2416 · 24 February 2023
oursДо этого обращался в другой сервис, там только развели руками. Проблема — не морозит. Проверили при мне, показали, что всё держит.
Данияр С.Order No. TS-2205-673 · 5 April 2022
oursДруг посоветовал, у него похожая история была. С чем пришёл: не морозит. Проверили при мне, показали, что всё держит.
Алексей Г.Order No. TS-4782 · 30 August 2021
oursБыло подозрение, что дело в плате, хотелось услышать второе мнение. Приехал из командировки, а дома — шумит. В списке работ — уплотнитель. Проверил дома — всё на месте, ничего не забыли
Татьяна Б.Order No. ZK-2020/765 · 2 October 2020
oursЖалоба простая: течёт. Отдельно спосибо мастеру — Дильмурат С, терпения ему хватило. Проверили при мне, показали, что всё держит!!
Евгений М.Order No. TS-5582 · 15 February 2016
oursДолго откладывал ремонт, потом всё-таки собрался. Привёз на диагностику: холодильник. С чем пришёл: намерзает лёд. Ни копейки сверху, как и обещали. Разобрали, посмотрели: уплотнитель. Приняли без очереди, оформили за пять минут. Хороший сервис, побольше бы таких. Крутит ровно, без рывков
Didn’t find the answer? Message us on WhatsApp.
Ask a questionIn Almaty, you can book a Lex refrigerator technician for home service through Tech Service: a dedicated specialist arrives anywhere in the city within 60 minutes. You can submit a request on the website or by phone, and diagnostics at home are free.
The refrigerant is sealed in a closed circuit and doesn't get used up on its own, so it lasts for the entire life of the refrigerator. A leak can only happen if the tubes or connections are damaged, and then a refill is needed after fixing the cause.
If the issue is localized — the compressor, control board, or sensor — repair is usually more cost-effective and cheaper than new equipment. If the body is damaged or complex repairs are needed, replacement may be more reasonable. The technician will explain after a free diagnostic.
With a refrigerant leak, the compartments gradually stop freezing, the compressor runs non-stop or shuts off quickly, and there may be an oily trace on the tubes. A broken sensor more often shows an error on the display and a jerky operation. The technician will determine the exact cause during diagnostics.
Check if the outlet has power, if the plug and cord are intact, if the door is closed tightly, and if the circuit breaker hasn't tripped. If the outlet works but the refrigerator is silent, the cause is in the compressor, start relay, or control board — that's a job for a technician.
In most cases, the control board is repaired or replaced, and the refrigerator keeps working. Replacement makes sense when the compressor or body is damaged and restoration isn't cost-effective. The technician will explain the decision after a free diagnostic.
Tech Service repairs Lex refrigerators in Almaty: a technician arrives at your home within 60 minutes anywhere in the city, diagnostics are free, and there's a 1-year warranty on labor and parts. Technicians with 4 to 20 years of experience understand error codes and typical Lex failures, and they quote the price after diagnostics.
The same "not cooling" symptom in a Lex refrigerator can come from different components — from a sensor to a refrigerant leak. We break down failures by symptom and show what the technician actually checks.
When the light is on but there's no cold, we first check the NTC sensors and the cooling circuit — these are the two most common causes in Lex. NTC sensors send temperature readings to the control board, and when they fail, the electronics "think" the compartment is already cold even though it's actually warm. At the same time, the technician inspects the circuit: looks for a refrigerant leak and checks the capillary tube for a clog. In this situation, the compressor may be working fine and may not even cycle off, so we don't condemn the motor based on sound. If the freezer is getting cold but the upper compartment isn't, the problem is more often a sensor or a clogged capillary tube, not the compressor — so don't rush to agree to a motor replacement before diagnostics. We start Lex refrigerator repair in Almaty with free diagnostics to pinpoint the exact component.
A click and shutdown after a couple of seconds is a typical sign of a start relay or control board, and our technician tells them apart on site. The start relay kicks on the compressor: as it wears, it clicks but doesn't send the needed pulse, and the motor stalls. A control board fails differently — after a voltage spike, it simply doesn't send the start command, and the refrigerator stays silent with no clicks. The technician tests the electrical line and the electronic module one after the other to separate one cause from the other and avoid replacing parts at random. If the relay clicks but the compressor won't start, don't replace the motor right away — first check the start circuit and the electronic module, otherwise a new part won't fix the root cause.
Ice buildup in a Lex No Frost system appears when the defrost assembly fails — the evaporator heater, thermal fuse, or fan. The defrost heater melts frost off the evaporator in a No Frost system on a cycle, and if the heating element burns out, ice doesn't have time to melt and builds up layer by layer. The thermal fuse cuts power in case of overheating, and the fan stops circulating cold air through the compartments when its blades freeze over. Visually, all three failures look the same — frost on the back wall and ice in the freezer. If ice builds up again a few weeks after defrosting, the problem isn't how you use it but the defrost assembly — and it needs to be found before ice blocks the fan.
| Component | Symptom | What we check |
|---|---|---|
| NTC sensors | one compartment not cooling | temperature readings on the board |
| Start relay | clicks and won't start | compressor start circuit |
| Control board | won't turn on after a surge | electronic module and traces |
| Defrost heater | ice in No Frost | defrost assembly and thermal fuse |
| Door gasket | ice buildup, loss of cold | seal around the perimeter |
| Circuit and refrigerant | not cooling, silent | seal integrity and circulation |
The message on the screen is a hint, not a verdict: it points to the component the technician checks first and helps avoid replacing parts blindly.
The code on the Lex display points to a specific faulty component, and our technician cross-checks it against actual sensor readings rather than relying on the message alone. NTC sensors measure the temperature in the fridge and freezer compartments, the control board collects their signals and shows a code on the display that indicates which circuit is out of range. The same code can appear because of either a sensor or the board, so decoding it without testing the circuit often leads to replacing a working part. In our experience, when we see such a message, the specialist first tests the sensor circuit and only then draws a conclusion about the electronic module. Note the conditions when the signal appears: after defrosting, when the compressor starts, or when the door is opened — this detail narrows down the search.
If the message on the Lex display remains after unplugging the fridge, we check the control board and sensor circuit — most often the cause is the electronic module after a power surge. Unplugging for a few minutes only resets a one-time glitch: the controller restarts the cycle and the code disappears from the screen. A persistent signal means the component is already faulty, not just frozen, and you shouldn't delay diagnostics to avoid damaging neighboring elements. A power surge in the mains damages the electronic module, and along with it the NTC sensors that receive power from the same board. A technician arrives within 60 minutes in the city, diagnostics are free, and on site it becomes clear what to replace — the module or a separate sensor.
We start repairing Lex refrigerators in Almaty with free diagnostics at home: a technician arrives within 60 minutes and identifies the faulty component on site.
We send our technician across the city within 60 minutes — they are our direct employee, not an intermediary, so the same technician performs the on-site diagnostics. We take requests by phone and ask for the model, symptom, and approximate age of the appliance: this helps the technician prepare for the specific series. Our employee arrives alone, without a team and without pushy add-on services, and inspects the appliance where it stands — in the kitchen, in a cabinet niche, or on the balcony. For Almaty residents, it's convenient that the technician inspects the refrigerator at home and you don't waste time on travel. Fast arrival matters not only for convenience: with a refrigerant leak or defrost failure, delay makes the breakdown worse.
During free diagnostics, we check the electrical circuit, board, sensors, and cooling circuit, and we quote the cost of work only after the inspection. First, they test the power supply and connectors, then examine the control module for burnt traces and swollen capacitors. NTC sensors are tested for resistance: their readings often differ from the actual temperature in the compartments, causing the compressor to run nonstop or not start at all. The cooling circuit is inspected separately — they look for oil traces on the tubes and measure pressure to confirm or rule out a refrigerant leak. On-site diagnostics are more accurate: our employee sees the Lex refrigerator in real operating conditions and identifies the cause rather than relying on a phone description.
Warranty and technician qualifications are what set a direct service apart from a middleman. Here's what our warranty covers and why the technician's experience matters when servicing Lex refrigerators.
We provide a 1-year warranty on labor and parts—it covers both compressor replacement and other components of a Lex refrigerator. The same condition applies to the entire scope of work: both the operation itself and the installed part, so whether we replaced a start relay or the whole compressor, the term is the same. For the owner, this means that a repeat call about the same component within a year is handled as a warranty case, not as a new request. In my view, the value here isn't in the wording itself but in the fact that it ties the technician to the result: it's not in their interest to install a questionable part they'll have to answer for later. A warranty on both the part and the labor means that if the same component fails again, the call is treated as a warranty case—that's the point of the condition for the owner.
A repeat breakdown usually means that the first time only the symptom was fixed, not the cause—for example, the relay was replaced without checking the compressor. The start relay is often the first to fail, but if its winding is already burnt, the new part won't last long, and in a couple of weeks the fridge won't start again. The same logic applies to refrigerant leaks: you can solder the tube, but without pressure-testing the circuit, the cause remains. That's why we start with diagnostics of the whole component, not just the failed part: we check the compressor windings, relay resistance, circuit tightness, and thermostat operation. Diagnostics identify the faulty component of the Lex refrigerator as a whole, and replacement is based on the actual cause. To keep the breakdown from coming back, the technician must check the entire circuit of the component, not just the failed part—that's what our free diagnostics is designed for.
Not every Lex refrigerator breakdown is worth fixing, and not every maintenance task requires a technician visit. Here's when repair makes sense, when replacement is smarter, and how to reduce the risk of repeat failures.
Repair makes sense when a single component fails — a relay, sensor, board, or defrost heating element — while the body and circuit remain intact; in that case, we bring the appliance back to life. Most often on Lex models, NTC sensors and the compressor start relay fail: they are inexpensive, replaced individually, and don't require opening the circuit. The control board is also repairable — if a trace or relay is locally damaged, it is restored rather than discarding the entire module. A power surge hits the electronics and start unit specifically, so after such an event the motor usually remains functional and doesn't need replacement. The decision should be made after diagnostics, not based on a symptom: sometimes "not cooling" is a sensor, not the compressor, and replacing the motor would be an unnecessary expense. In my view, the exact cause is more cost-effectively determined by the appliance's behavior in the first minutes after switching on than by external signs.
If the cooling circuit or the compressor along with the board has failed, and the unit itself is old, replacing the appliance is often more reasonable than repairing it. A clogged capillary tube disrupts refrigerant circulation — cleaning and recharging require opening the circuit, and on a worn-out unit the risk of repeated leakage is higher. Replacing the motor and board on a model with exhausted service life brings other components along: a few months later, the fan or defrost may fail. You need to assess not only the breakdown but also the condition of the seals, body, and electronics: if several components are worn at once, restoring one won't give a long-lasting result. In our practice, age and overall condition are decisive: an appliance whose door doesn't hold cold and whose body shows corrosion rarely justifies investment in a new compressor.
A Lex refrigerator breaks down in several typical scenarios, and the outcome depends on diagnostic accuracy, not on how quickly the first suspicious part is replaced.
90brands
We work with every brand sold in Kazakhstan — from Samsung, LG and Atlant to Biryusa, Indesit, Stinol and rare imported makes. Can’t find yours in the list? Call anyway — a technician will come and take a look.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your refrigerator stops working, first check the outlet, the power cord, and the thermostat setting, and after defrosting let it stand for a while.
4 February 2026 · 12 minutes read
If your refrigerator isn't cooling but the light is on, the cause is usually one of the components in the cooling circuit: the compressor, thermostat…
10 December 2025 · 13 minutes read
If your dishwasher won't drain, the most common culprits are a clogged filter or drain hose; less often, it's the pump, impeller…
24 March 2026 · 12 minutes read
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
If your microwave isn't heating but the light and turntable still work, the problem is usually one of the high-voltage components — the magnetron, diode…
15 February 2026 · 12 minutes read












