experience14 yearsVladimir D.
Air conditioner service technician
City
Language
What broke
Sections
Message on WhatsApp+7 (775) 030 02 94Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Free diagnostics.
Our own technicians4 to 20 years of experience




Repair prices
Below are typical symptoms and likely causes. The technician will pinpoint the exact cause after diagnostics.
clogged filter, low refrigerant level
from6 000 ₸
worn bearings, fan imbalance
from9 500 ₸
clogged drain, damaged drain pan
from4 000 ₸
no power, control board failure
from9 500 ₸
faulty heater, sensor error
from6 000 ₸
sensor fault, communication failure
from6 000 ₸
clogged filter, blocked air duct
from7 500 ₸
end of service life, lack of lubrication
from9 500 ₸
The cost depends on the type of fault and the fan coil model.
1 visittime
from 7,500 ₸cost

BeforeAfter5 steps

From request to performance check — five steps.
Submit a request and a technician will come to you.
The technician will arrive anywhere in the city within 60 minutes of your request.
We'll arrange access to the equipment and record the symptoms as described by the owner.
You approve the scope of work and the cost, then the technician starts the repair.
The technician will check the fan coil operation and provide a 1-year warranty on labor and parts.
The climate control equipment repair department in Almaty has 8 technicians with 4 to 20 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience14 yearsAir conditioner service technician
experience20 yearsSenior air conditioner installer
experience12 yearsAir conditioner repair technician
experience16 yearsIndustrial air conditioner technician
experience4 yearsAir conditioner service technician
experience14 yearsAir conditioner maintenance technician
experience7 yearsClimate control system repair technician
experience5 yearsAir conditioner installation technician
We reply during working hours
Submit a request — a technician will arrive within 60 minutes anywhere in the city. Diagnostics are free. You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies.

Warranty question? Call us
+7 (775) 030 02 947 898 reviews of repairs at TECH SERVICE in total
Индира П.Order No. 2023-3175 · 9 April 2023
oursПервый раз сюда, до этого чинился в другом месте. Отдельно скажу про мастера: Сергей Архипов — спокойный, без лишней суеты. Не пожалел ни разу.
Андрей П.Order No. ZK-2021/844 · 14 December 2021
oursНашёл по отзывам, решил попробовать. Выбирал по отзывам в 2ГИС, времени на эксперименты не было. Отдельно спосибо мастеру — Никита М, терпения ему хватило!!
Молдир С.Order No. ZK-2020/596 · 12 December 2020
oursПришёл по записи, всё прошло спокойно. Цену назвали не сразу, пришлось уточнять. Ребёнок уже проверил на прочность, держиться.
Диана М.Order No. 70031 · 9 April 2019
oursНашёл по отзывам, решил попробовать. Работаю допоздна, поэтому нужен был сервис с нормальным графиком. Радик Т помог выбрать, без навязывания!!
Эльвира Д.Order No. TS-1807-608 · 16 December 2018
oursПришёл по записи, всё прошло спокойно. Ораз не стал навязывать дорогую запчасть, поставил нормальную.
Жанар Т.Order No. TS-1804-652 · 7 September 2018
oursПервый раз сюда, до этого чинился в другом месте. Выбирал по отзывам в 2ГИС, времени на эксперименты не было. Пять звёзд, не задумываясь.
Марат Ж.Order No. 676363 · 14 July 2018
oursОбращаюсь не первый раз, поэтому есть что сказать. Нужен был счёт и чек, у нас техника на балансе организации. Дмитрий Радионов честно сказал, что менять, а что ещё походит.
Виктор Ф.Order No. 345907 · 10 April 2018
oursПришёл по записи, всё прошло спокойно. Спасибо за работу). Приняли быстро, объяснили, что и как будет.
Александра Н.Order No. 643265 · 7 March 2017
oursДолго откладывал, но пришлось обратиться. Прочитал кучу отзывов, половина — реклама, но тут вроде живые. В общем, доволен.
Тимур И.Order No. 974503 · 9 January 2017
oursПервый раз сюда, до этого чинился в другом месте. Не идеально, но честно.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionFirst, check the unit's power supply and the remote or thermostat settings, as well as the mode switch position. If there's power but the fan coil stays silent, you'll need a technician — the cause is usually in the wiring or the control board.
The cause can be in either the fan coil or the system: a clogged heat exchanger, a faulty valve, or insufficient chilled water from the chiller. The technician checks both the unit and the water supply to pinpoint the culprit.
It depends on the model, but most often the culprit is a worn fan motor bearing, less often an unbalanced wheel or a loose mount. The technician identifies the assembly on site and decides whether to replace the bearing or the motor.
The code points to an assembly rather than giving a ready diagnosis, and its meaning depends on the model. The technician checks the code against the manufacturer's documentation and confirms the cause by testing the assembly itself.
If the unit still doesn't cool, makes noise, or leaks after cleaning the filters and heat exchanger, the problem is a faulty component, not dirt. In that case, you need a specific part repaired, not maintenance.
A leak can damage the ceiling and finishes, while a faulty motor or wiring can lead to overheating and a short circuit. It's better to turn off the unit and wait for the technician than to keep running it with a fault.
Tech Service repairs fan coils in Almaty: a technician arrives at your door within 60 minutes anywhere in the city, or the unit is repaired at our service center. Diagnostics are free, we identify the cause before any work begins, and we provide a 1-year warranty on labor and parts. We repair the specific faulty component, not the entire unit.
A fan coil is the indoor unit of a chiller-fan coil system. To understand what exactly breaks and why, owners should know its components and how it differs from a household air conditioner — this determines who to call and what to check.
A fan coil receives cold or heat from an external chiller via pipes carrying water or refrigerant, rather than from its own compressor like a household split system. Inside, there is a heat exchanger through which the fluid from the chiller flows, and a fan that distributes air throughout the room. The compressor, condenser, and the entire refrigeration machine are located separately — in the chiller, often on the roof or in the building's technical room. Therefore, the unit itself does not produce cold; it transfers it from the central machine. This leads to a practical conclusion: if the fan coil is not cooling, the cause may not be in the unit itself but in the chiller or the piping, so diagnostics start with checking the entire system, not just the indoor unit.
We work on individual components and do not touch the chiller if the cause is in the unit, and if we suspect a system issue, we check the piping and connections before naming the cause. This approach saves the owner time: there's no need to take the unit to a service center if the fault is local, and a technician with 4 to 20 years of experience identifies it on site. An on-site technician arrives anywhere in the city within 60 minutes, and diagnostics are free — the cost of work is quoted after inspection, once the cause is clear. For Almaty residents, this means no guesswork with the ceiling: we first check the piping, valves, and system power, then tackle the unit itself. In our practice, most issues are local faults in a component, and on-site work solves the problem without removal.
Owners usually come with a specific symptom: it won't turn on, doesn't cool, water drips, or it hums. Below is a map of "what the client sees → likely cause → what the technician checks" so you have a rough idea of the scale of the breakdown before the specialist arrives.
Most often, the unit won't turn on due to the control board, power supply, or thermostat, and we start diagnostics by checking power and the signal from the remote, not by disassembling the unit. The control board manages modes and displays error codes, so the first thing the technician checks is whether voltage reaches it and whether the command from the remote or wall thermostat is coming through. If there is a signal but no response, we check the controller and contacts: oxidation or a loose connector can produce the same effect as a burned-out board. Our diagnostics are free, so the cause is identified before any work, and the technician arrives within 60 minutes anywhere in the city. If the unit is connected to a central chiller in a business center, it's worth first checking whether the system as a whole is running: sometimes the fan coil is fine but the central system is down.
Weak cooling or no heat usually comes down to the heat exchanger, clogged filters, or a refrigerant leak, and we check airflow and the condition of the heat exchanger before concluding the cause. Clogged air filters reduce airflow, the heat exchanger gets coated in dust and stops delivering cold or heat, and a refrigerant leak in the line produces the same picture even when the fan is working. The technician measures the air temperature at the inlet and outlet, inspects the heat exchanger, and only then decides whether the components need repair. If the unit runs but doesn't cool, it's not always a failure of the unit itself: the cause can be in the chiller or the line, so the technician checks the whole system before recommending a repair. Our technicians have 4 to 20 years of experience, and that's what makes this kind of diagnostics accurate.
Water on the floor is most often a clogged drain or an overflowing condensate pan, while noise and vibration point to the fan bearings or motor, and we check those components first. The drainage system and drain pump remove condensate; when the drain clogs or the pump stops pumping, the pan overflows and water escapes. Humming and vibration appear when the fan bearings wear out or the wheel becomes unbalanced — the part is replaced to keep the motor from burning out. A leak can't wait: moisture near the board's electrics is more dangerous than the breakdown itself, so if it's actively dripping, it's best to cut power to the unit before the technician arrives. We provide a 1-year warranty on labor and parts, so the fixed cause won't come back the same way.
A code on the display scares the owner, though by itself it only points to the component where the protection tripped. Let's look at what such a hint means and why the exact model matters more than a ready-made decoding.
An error code on the fan coil display points to the component or mode where the protection tripped, but it doesn't name the specific fault, so decoding is only the start of diagnostics. The control board records a deviation: pressure drop in the circuit, compressor overheating, fan stoppage, temperature sensor failure, or overcurrent lockout. Behind each such signal is a range of possible causes — from a clogged filter and air lock to a worn motor bearing. The same code can mean different things on different models, so without the exact model and manual it's easy to misread and replace a working component. In my view, the worst case is when the owner buys a part based on an internet decoding: the component gets replaced, but the protection trips again because the real cause was somewhere else.
We ask for the exact fan coil model before the visit because code tables and component design differ between manufacturers, and this speeds up diagnostics. The marking is usually on the unit's nameplate or in the equipment passport: using it, the specialist checks the table for that specific series in advance, prepares the right sensors, and plans the inspection. With the exact model, they immediately know where the control board is and how to remove the panel without damaging the fasteners. If the marking is unknown, the cause will still be determined on site, but with accurate data the check goes faster and less often requires a second visit. In our practice, the longest cases are exactly the unnamed units where the nameplate is painted over or lost.
Not every fan coil repair is done on site. Below is what determines the format of work and how to tell when the unit can be fixed at home and when it needs service.
Most local issues — fan, drainage, filters, board, remote — we fix on site, and a technician arrives within 60 minutes anywhere in the city. The on-site technician brings tools for typical tasks: cleaning the drainage system, replacing the filter element, checking electrical connections, and setting up the remote control. On site, they open the casing, inspect the heat exchanger and drain pan, test the terminals, and see how the unit responds to commands from the remote. Diagnostics are free — they are done before any work, and the technician gives the price only after the inspection. On-site service saves the owner time: no need to remove the casing and go without climate control, and the technician immediately checks the result with a test run. If the inspection confirms the cause, the technician agrees on the scope of work with you and starts fixing it on site.
A fan coil is taken to the service center when a unit needs repair that can't be done neatly on site, and we explain in advance why we suggest this format. This applies to work that requires disassembling the heat exchanger, straightening a deformed drain pan, or restoring the bearing seats of the fan — such operations can't be done on site without risking damage to neighboring parts. The decision to replace the whole unit or repair the component is based on the condition of the part: often it's enough to replace one element, and that costs less than replacing the entire unit, but the technician makes the final call after diagnostics. Before taking it away, they explain what exactly requires workshop conditions and what could have been done on site — so the owner understands the logic behind the suggested option.
Repair and maintenance solve different tasks. Below is how the process works step by step and how to tell when cleaning is needed versus when repair is needed.
If the fan coil unit blows weakly, smells, or freezes up while the electricals are fine, it usually needs cleaning of the heat exchanger and air filters rather than replacement of parts. A clogged heat exchange block loses heat transfer, and the unit blows warm air even in cooling mode. Filter elements clog with dust fastest, and along with them dirt settles on the fins and in the drain pan. Airflow drops, the fan runs overloaded, and a musty smell appears from stagnant moisture. The signs that point specifically to repair are different: the motor won't start, water leaks from the pan when the drainage system is clean, bearing knock is heard, modes don't switch. Clogged filters reduce airflow and cause odor, and at an early stage this is solved by maintenance, while an advanced clog eventually leads to fan overload.
| Operating conditions | What we check | How often |
|---|---|---|
| Apartment, seasonal use | filters, condensate drain | before the season |
| Office, daily load | filters, heat exchanger, drainage | quarterly |
| Business center, high foot traffic | heat exchanger, drain pan, controls | quarterly |
| Dusty room or near the street | filters, heat exchanger fins | monthly |
Warranty is the main argument when choosing a technician for climate control equipment repair. Below we explain exactly what we cover and what to do if the fan coil unit fails again after service.
We provide a 1-year warranty on labor and parts, meaning both the service itself and the installed part are covered. This term applies to both directions at once, not just the operations performed: if a replaced component fails after a few months, the claim goes through the parts warranty. The separate wording matters: if a part fails before its time, it's a warranty case on the part, not a reason for a new labor charge. Our technicians with 4 to 20 years of experience record exactly which component was replaced and what was done to the system — this record makes it easier to prove the connection between a repeat failure and the work performed. Without such a link, a dispute about the cause drags on, and the client is left between two versions — their own and the service's.
If the unit fails again after service, we handle it under warranty: the technician checks whether the repeat symptom is related to the work performed or to another component. First, we record exactly what has changed since the visit — remote control behavior, air temperature at the outlet, appearance of noise or leaks. A repeat symptom doesn't always mean the same breakdown: sometimes a related component acts up that was fine during the first diagnosis, so a repeat check is important, not guesses. We don't suggest replacing parts at random — first we determine the cause, and that determines whether it's a warranty case or a new fault. Diagnostics for a repeat call is also free: first the technician finds the source of the failure, and only then do we discuss whether the situation falls under warranty or not.
You can call a technician for fan coil unit repair in Almaty directly: Tech Service is a direct provider with its own technicians, not an aggregator, and you can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies. A technician arrives within 60 minutes in the city, diagnostics is free: the specialist comes, finds the cause, and only then quotes the scope of work. The technician gives the price after free diagnostics, so over the phone you don't get an "average price" but a specific cause and scope of work on site. A direct provider means our own person comes to the site, not an intermediary with someone else's crew — this makes warranty and accountability for the result simpler. You can pay for labor and parts in any convenient way — cash or card.
Here are the key things to keep in mind before calling a technician and while discussing faulty equipment in your apartment or office.
7brands
We source parts by model and part number for equipment from these brands.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
Air conditioner errors are codes on the display or flashing indicators that show which component has failed.
5 March 2026 · 12 minutes read
Gas boiler errors are codes on the display or a flashing indicator that point to a specific component: ignition, pressure, draft, sensor, or control board.
10 February 2026 · 11 minutes read
If your air conditioner is leaking, first turn it off and cut the power, place a container under the drip, and move any wiring away from the water.
19 October 2025 · 12 minutes read












