Open until 19:00+7 (778) 046 88 53Call a technician
Tech Service technician next to a welding machine

Welding Machine Repair in Almaty

A technician arrives within 60 minutes anywhere in the city. Free diagnostics, 1-year warranty on labor and parts.

  • 1-year warranty
  • 4 to 20 years of experience
  • Kaspi QR, Kaspi Red, card, cash and bank transfer

Our own technicians4 to 20 years of experience

Ruslan Ts.Damir M.Dilmurat S.Dima

Repair prices

  • Diagnostics0 ₸
  • Connectors and cables repairfrom2 500 ₸
  • Preventive maintenance and cleaningfrom2 500 ₸
  • Relay replacementfrom2 500 ₸
  • Cooling system repairfrom3 500 ₸
All prices
2ГИСЯours4,97 898 reviews
2GIS · Google · Yandex · order database
Common faultsCommon faultsTECH SERVICE02

Common welding machine faults in Almaty

Below are the frequent symptoms customers bring to the shop and the likely causes. The technician will pinpoint the exact cause after diagnostics.

PricesPricesTECH SERVICE03

How much welding machine repair costs in Almaty

The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.

Connectors and cables repairparts not included

1–2 hours

from2 500 ₸

Preventive maintenance and cleaningexact price — after the free diagnostics

1–2 hours

from2 500 ₸

Relay replacementparts not included

1–2 hours

from2 500 ₸

Cooling system repairparts not included

1–3 hours

from3 500 ₸

Transformer repairparts not included

1–3 hours

from4 000 ₸

TECH SERVICE mobile technician with a tool case

How welding machine repair works on site in Almaty

From request to testing the machine under load.

  1. Requestsame day

    Describe the symptom and machine model so the technician can prepare.

  2. Visit schedulingwithin 60 minutes

    The technician will confirm your address and a convenient arrival time so you don't have to wait.

  3. Diagnosticsfree

    The technician inspects the machine and identifies the faults.

  4. Work approvalafter inspection

    You approve the list of work and parts replacement.

  5. Machine handoverafter repair

    Ask the technician about the results and warranty terms.

Leave a request
TechniciansTechniciansTECH SERVICE04

Our home appliance repair technicians in Almaty

The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

  • 8 technicians in Almaty
  • 8–12 years of experience in the department
  • Article author Ruslan Ts., 9 years of experience
Mobile technician fixing a washing machine at the customer's home
Field technician at a customer’s home

The department has 8 specializations — they are listed on the technicians' cards.

01 / 08
Ruslan Ts., washing machine and refrigerator repair technicianexperience9 years

Ruslan Ts.

Washing machine and refrigerator repair technician

Damir M., general household appliance repair technicianexperience12 years

Damir M.

General household appliance repair technician

Dilmurat S., field technician for washing machine and refrigerator repairexperience10 years

Dilmurat S.

Field technician for washing machine and refrigerator repair

Dima, expert washing machine repair technicianexperience8 years

Dima

Expert washing machine repair technician

Nikita M., field refrigerator repair technicianexperience8 years

Nikita M.

Field refrigerator repair technician

Oraz, senior washing machine repair technicianexperience8 years

Oraz

Senior washing machine repair technician

Radik T., dishwasher repair technicianexperience11 years

Radik T.

Dishwasher repair technician

Rustem T., washing machine repair technicianexperience9 years

Rustem T.

Washing machine repair technician

We reply during working hours

Book welding machine repair in Almaty

Provide the machine model, symptom, and operating conditions. Mention at what load the fault appears and how long ago it started.

TECH SERVICE administrator replying to a customer's WhatsApp message

Warranty question? Call us

+7 (778) 046 88 53
Customer reviewsReviewsTECH SERVICE05

Reviews of welding machine repair in Almaty

Елдос К.Order No. TS-2611-647 · 26 August 2026

ours

Пробовал найти мастера в своём районе, но все были заняты. Настроение было испорчено конкретно. Основная жалоба — выбивает. Рустем Т принял, посмотрел и сразу сказал, что делать. Заодно поменяли: плата. Сказали 15 000, а потом ещё и скидку сделали. Гудит ровно, не греется, всё как надо.

Repair: welding machine repair in

Томирис Ж.Order No. 2025-2761 · 20 June 2025

ours

Техника на гарантии уже не была, так что выбор был свободный. Внешне как новый, если не считать мелкой царапины.

Repair: welding machine repair in

Алишер У.Order No. 296464 · 4 May 2025

ours

Было подозрение, что дело в плате, хотелось услышать второе мнение. Нагрев в норме, постороних звуков нет!!

Repair: welding machine repair in

Ольга М.Order No. TS-2505-214 · 5 March 2025

ours

Нужен был счёт и чек, у нас техника на балансе организации. Нужен был ремонт сварочного инвертора — обратился сюда. Первое, что заметил: не варит. Рустем Т объяснил причину так, что понял даже я. Приняли, выдали квитанцию, всё по-человечески. Даже с учётом запчасти вышло гуманно. Включил, проверил, работает.

Repair: welding machine repair in

Карина А.Order No. ZK-2024/425 · 23 December 2024

ours

Смотрел, у кого есть запчасти на такую модель. Первое, что заметил: выбивает. Включил, проверил, работает!!

Repair: welding machine repair in

Жасмин Р.Order No. TS-2402-671 · 14 July 2024

ours

Повод для визита: выбивает. Рустем Т помог выбрать, без навязывания. Уже полгода — ни одного сбоя.

Repair: welding machine repair in

Санжар О.Order No. ZK-2847 · 26 June 2024

ours

Телефонмен кеңес сұрадым, тегін айтты. Диагностика тегін болды, бұл жағы жақсы. Бөлшектің бар-жоғын бірден тексерді, қоймада бар екен. Мастер кешке дейін күтпей, сол күні аяқтады. Бөлшек екі күнге кешікті, бірақ ескертті.

Repair: welding machine repair in

Тимур А.Order No. 406817 · 24 November 2023

ours

Искал мастерскую поближе к дому, чтобы не мотатся с техникой через полгорода. Ещё утром всё работало, а к вечеру — выбивает. Сказали 7 500, а потом ещё и скидку сделали. Нужна была замена: плата. Мастер сам перезвонил, когда появилась запчасть. Буду советовать знакомым. Сделали аккуратно, следов разборки не видно

Repair: welding machine repair in

Станислав К.Order No. TS-2104-553 · 18 April 2021

ours

Цена имела значение, но и гарантия тоже. Оставил заявку на ремонт сварочного инвертора. Проблема — выбивает. Внешне как новый, если не считать мелкой царапины)

Repair: welding machine repair in

Нурасыл М.Order No. TS-2007-142 · 17 October 2020

ours

Проблема — выбивает. Дамир М возился с этим дольше, чем планировал, но довёл до конца. Гудит ровно, не греется, всё как надо.

Repair: welding machine repair in
Questions and answersQuestionsTECH SERVICE06

Questions about welding machine repair in Almaty

Didn’t find the answer? Message us on WhatsApp.

Ask a question
Can a welding machine with a burnt-out power module be repaired?

Yes, burnt power transistors and diodes are replaced separately if the control board is intact. The technician will check the entire power circuit so the new module doesn't fail right after installation.

Do you repair Resanta and Fubag welding machines in Almaty?

Yes, these brands are among those our technicians work with, along with Svarog. They are familiar with the circuits of inverters, semi-automatic and TIG machines from these brands, so repairs are possible at the component level.

Can a welding inverter be fixed on-site in Almaty?

Some faults are fixed on the spot: cables, connectors, maintenance, simple glitches. If power components or the board need replacing, the machine is taken to the service center — it depends on the model and the fault.

Why is it dangerous to keep welding with a machine that sparks and smells burnt?

That sign points to a fault in the power section or insulation, and continued use can finish off the control board. It's better to stop welding right away and send the machine for diagnostics so you don't have to replace more components.

How can you tell if the diode bridge in a welding machine has burnt out?

With a shorted bridge, the machine holds the arc poorly, hums or trips the breaker, and the output voltage drops. You can only confirm it by testing the parts during diagnostics — it depends on the model.

Is there a warranty on board replacement in a welding machine?

Yes, there is a 1-year warranty on labor and parts. This covers both control board replacement and replacement of transistors or the diode bridge after repair.

Repair guideArticleTECH SERVICE07

Welding Machine Repair in Almaty by Tech Service

Author: TECH SERVICE editorial team

Published
Updated

Tech Service repairs welding machines in Almaty as a direct contractor: our technician arrives at your home within 60 minutes or takes the machine to our service center. Diagnostics are free, and you get a 1-year warranty on labor and parts. Our technicians have 4 to 20 years of experience. The technician provides the price after diagnostics.

Why Your Welding Machine Stopped Welding and Whether You Need Welding Machine Repair

The machine turns on but won't weld, or it's completely dead — each symptom points to a specific component. We break down the typical signs of failure and explain what they mean.

The Machine Won't Turn On or Trips the Breaker

If your welding machine won't turn on or immediately trips the breaker, the cause is usually in the power section — a blown diode bridge, a burnt-out IGBT module, or a short circuit in the power supply circuit. Power transistors and the rectifier bridge operate under heavy load and are the first to fail during overheating or voltage spikes, taking the fuses with them. The control board may remain intact, so the machine looks fine until you try to turn it on. Diagnostics start with testing the power section and checking insulation, not with randomly replacing fuses. Don't turn the machine back on after the breaker trips — that adds control board damage to the burnt transistor and makes recovery more complicated. If the breaker trips again, unplug the machine and call a technician: further attempts to turn it on only expand the damage.

It Turns On but Won't Hold an Arc or "Sputters"

  • The arc sputters and goes out: a loose contact in the connector or an oxidized ground terminal is to blame — the current fluctuates and ignition fails.
  • The current regulator doesn't respond: the potentiometer is worn, so the current doesn't change and the knob turns in jerks.
  • The arc ignites intermittently: the cable or electrode holder is damaged — a broken wire inside the insulation creates a floating contact under load.
  • Welding is jerky and the cable heats up: the diode rectifier is blown, so part of the half-wave is lost and the arc becomes unstable.
  • The machine hums but there's no arc: an open circuit in the holder circuit or poor ground contact — check the terminals and the integrity of the wire.

It Hums but Won't Weld, or Sparks and Crackles Inside

Humming without welding and crackling inside the casing indicate a faulty transformer, capacitors, or a blown power module — we diagnose such machines by checking the power section first. Welding transformers with inter-turn short circuits start humming louder than usual, and swollen or blown capacitors produce a characteristic crackle and burnt smell. A blown IGBT module or power transistors often show themselves exactly this way: the machine turns on, the fan spins, but there's no working voltage at the output. Our technicians with 4 to 20 years of experience test the windings and check capacitance to replace burnt power transistors and IGBT modules rather than the entire board. Crackling and a burnt smell are a reason to immediately unplug the machine: operating with a blown capacitor or transistor damages neighboring components on the board.

Overheating, Shutdowns, and Error Codes on the Inverter During Welding Machine Repair

The inverter shuts down after a few minutes of operation or shows an error on the display. We explain when this is normal protection and when it's a sign of a fault.

The Machine Overheats and Shuts Down After a Few Minutes

If the machine shuts off after 5 minutes of operation, the most common culprits are a clogged or stalled cooling fan, as well as dried-out capacitors and a faulty thermal protection sensor. The fan gets clogged with dust and metal shavings from welding, its speed drops, and the heatsink stops getting airflow. Electrolytic capacitors lose capacitance from heat and age, causing the power section to run under overload and heat up more. The thermal sensor mounted on the heatsink, when it fails, either doesn't send a shutdown signal or triggers falsely on a cold machine. The built-in overheat protection kicks in during prolonged operation at maximum current — if the inverter shuts down at moderate load, that's already a fault, not normal. Before turning it back on, let the case cool down and check whether the fan blade spins freely by hand — a seized bearing is audible as a hum right after startup. Also inspect the heatsink for light between the fins — a finger-thick layer of dust cuts airflow almost in half, and protection triggers earlier than it should.

What the error code on the display means

An error code on the inverter display is the controller's signal about a specific component: overheating, overcurrent, low supply voltage, or a control board fault. The controller reads temperature and current sensor data, compares them with firmware thresholds, and displays the number on the screen. On budget models, a code often indicates a group of faults rather than one specific issue. Low mains voltage sags the power section, the machine goes into protection and shows a power error — while the inverter itself may be fine. Code decoding differs between brands, so you can't judge the fault by a single code — you need to check the control board and power section under load. Write down the code and the conditions under which it appeared — this information narrows the search even before opening the case. Also note whether the error repeats at idle or only appears under welding: this immediately separates low-voltage and power-section hypotheses.

Table of symptoms and likely causes

SymptomLikely causeWhat we check
Shuts off after 5 minutesFan, capacitorsCooling, thermal sensor
Error code displayedControl boardController, power circuits
Hums, doesn't weldTransformer, modulePower section
Sparks, cracklesCapacitor, terminalsInsulation, contacts

How welding machine repair goes from diagnostics to test welding

The work proceeds step by step — from free diagnostics to load testing. We show each stage so you understand what's happening with the machine and at which step the cost is quoted.

Free diagnostics and fault finding

Diagnostics are free with us: a specialist checks the power and control sections, finds the faulty component, and only then quotes the cost of work. First, they inspect the machine for signs of overheating and insulation damage, then test the diode bridge, capacitors, and power switches, and separately test the control circuits and protection. Based on the results, they explain which component failed and why — burned out from overload, from mains voltage sag, or from dust and moisture ingress. This is how welding machine repair in Almaty begins: agreeing on work before opening the case makes no sense — the real cause is only visible after checking the board and power components, so diagnostics come first. A city call-out takes up to 60 minutes, and the check itself is not charged.

Replacement of burned-out components

  • Power transistors and IGBT modules: we replace them when the switches break down, causing the machine to lose its arc or trip the breaker in the panel.
  • Diode bridges: replacement is needed for open circuits and for shorted diodes — the inverter hums but won't weld.
  • Electrolytic capacitors: we install new ones when they bulge or lose capacitance, which causes power loss and humming.
  • Control board: we repair it, and replace it if necessary, when modes, display, and overheat protection malfunction.
  • Connectors and wires: we restore contact on terminals and in harnesses if the machine sputters or loses connection with the torch.
  • Checking adjacent circuits: we test components around the burned-out unit so the new part doesn't fail on first power-up.

Load testing and test weld

The job isn't considered finished until the machine is tested under load — we do a test weld and make sure the arc is stable and the protection doesn't trip. The technician sets the working current, runs a control bead on test plates, and watches how the inverter behaves: no repeated shutdowns, no overheating of the power section beyond normal, and the arc holds steady in different modes. We also check that the fan and overheat protection work correctly and that no error code appears on the display. Test welding reveals what you can't see at idle: arc instability, repeated overheating, protection tripping at working current. After the check, we provide a 1-year warranty — on both labor and parts.

Repair at home or at the service center

Some breakdowns the technician fixes on the spot, while others require disassembly and testing at the service center. We explain when a home visit is possible and when it's better to bring the machine in.

When the technician comes to your home

Our technician arrives within 60 minutes anywhere in the city and fixes on-site issues that don't require disassembling the power section — problems with the cable, terminals, electrode holder, and fan. The visiting technician brings tools and common consumables, so restoring contact on a terminal, re-soldering the power cord, and replacing a dust-clogged cooling fan can be done without transporting the machine. We also check whether the device holds the arc after the intervention and inspect the working conditions — humidity, dust, power quality. This format saves time but doesn't replace a full diagnostic: if the cause is in the board or power modules, the welder will still need to be brought to our service center. In my opinion, a home visit makes sense when the fault is visible from the outside and not hidden deep in the circuit.

When service center repair is needed

Service center repair is needed when the breakdown is in the power section or control board — that requires disassembly, component replacement, and load testing, which can't be done at home. Inverter circuits and IGBT modules are replaced only at the service center: after soldering, the unit is run under load and test-welded to make sure the arc is stable and heating is normal. Our diagnostics are free, so at the inspection stage you already understand what you're dealing with and which components are suspect. If the on-site technician sees that the cause is deeper, he will tell you honestly — he won't fake a repair on the spot, because there's no point in returning to the machine again. The control board and power modules require a test bench and parts replacement — that determines where the repair will take place.

Table: what we fix at home and what at the service center

FaultWhere we fix itWhat we do
Cable, terminals, holderAt homeRestore contact
Cooling fanAt homeClean or replace
Control boardAt the service centerDiagnostics, replacement
Power modulesAt the service centerReplacement, test weld

What machines and brands we repair

We repair various types of welding equipment — from inverters to MIG/MAG and TIG machines. Here's what typically breaks in each type and which brands we see most often.

Inverters, MIG/MAG and TIG welders

  • Inverter power sources: compact models where power IGBT modules and their driver circuits often fail after overheating or a voltage spike.
  • MIG/MAG welders: weak points are the wire feed mechanism and control board, as well as the torch and connection socket.
  • TIG welders: the oscillator, high-frequency section and arc ignition unit suffer, causing unstable starting.
  • Welding transformers: windings, mode switch and terminal connections — simple design but require careful rewinding.
  • MMA machines: electrode holder, cables and power section; after working at maximum current, we check ventilation and thermal protection.

Resanta, Fubag and Svarog machines

We work on devices from popular brands — Resanta, Fubag, Svarog; for each brand, our technicians know the typical weak points and select suitable components. In budget Resanta inverters, power modules and the standby power supply often fail; in Fubag, the control board and connectors after working in dusty conditions; in Svarog, the power section and ventilation under prolonged load. Our technicians have worked with these lines for 4 to 20 years, so based on the symptoms they can often predict which unit to check first. The model name helps: different versions of the same brand are built differently, so when you call, please provide the exact model — this speeds up parts selection and diagnostics.

Repair or buy a new machine

Repair is usually more cost-effective than buying new if the casing, transformer and main components are intact and the fault affects individual parts — boards, modules, capacitors. When the power section is intact and there are no signs of extensive overheating, replacing one unit gets the device back in working order, and the casing and mechanics continue to serve. The question is different if the transformer windings are damaged, a large area of the board is burned, or the casing is deformed by heat: then overall wear makes repair questionable. The decision is made after diagnostics — we offer it free of charge, and the technician gives the price based on the results. Sometimes replacing one unit solves the problem; sometimes it's more honest to say that repair is not advisable — the technician will tell you directly, without pushing unnecessary work.

Warranty and how to choose a direct service provider

The market has many intermediaries and ads without warranty. Here's what to look for when choosing a service provider and what direct service offers.

1-year warranty on labor and parts

We provide a 1-year warranty on labor and parts — if the fault returns after repair, we fix it under warranty. The commitment covers replaced power modules, the control board, and output diodes: the client does not pay twice for the same unit. Over 4–20 years of practice, our technicians have seen that cheap one-time fixes cost more than a second visit, so we discuss warranty terms before starting work. Warranty on parts is just as important as warranty on labor: a component that fails again is the service center's responsibility, not the owner's. Before handing over your equipment, ask whether consumables are covered and how to file a warranty claim — this prevents most disputes in advance.

Direct service provider or intermediary

Tech Service is the direct contractor: our technician restores your equipment, not an intermediary who passes it to a third party and takes no responsibility for the result. Our specialist performs the free diagnostics, identifies the cause of the breakdown, and replaces burned-out components — you deal with the same person who handled your device. For on-site visits in the city, the technician arrives within 60 minutes and works on the spot, without sending the device through a chain of subcontractors. With an intermediary, you never see who repairs your equipment or how, and the warranty often remains just words — a direct service stands behind the result with its name and commitment. Before work begins, ask who will actually solder the board and whether that person backs it with a warranty — that way the intermediary is visible right away.

What to look for when choosing a technician

  • Who does the repair: ask whether the technician will come personally or whether the device will be handed to a third party without your involvement.
  • Warranty: ask if they provide a warranty on the work performed and on replaced parts, not just promises over the phone.
  • Load test: after replacing components, the inverter should run a test weld, not just power on.
  • Diagnostics: a transparent technician explains the cause of the breakdown before any intervention and shows which component burned out.
  • Payment: ask what payment methods they accept and at what stage payment is made.
  • Explanation: if the technician cannot clearly explain what broke and what will be replaced, that's a reason to be cautious.

What to remember about welding machine repair

Welding machine repair doesn't end with replacing a part but with a load test — keep that in mind when choosing a technician and discussing the work.

  • Diagnostics come first: a free check shows whether the power module burned out, the capacitor dried up, or the overheat protection tripped.
  • Component replacement: specific burned-out board elements are replaced, not the whole unit — this makes servicing cheaper than buying a new inverter.
  • Test weld: the machine is tested under load on a real weld, not just by multimeter readings at idle.
  • Warranty: a 1-year warranty on labor and parts formalizes the technician's responsibility and gives time to detect a hidden defect.
  • Understanding symptoms: an accurate description — won't turn on, sputters, hums, shows a code — shortens the search for the cause and avoids unnecessary work, and therefore overpaying.

8brands

Which welding machine brands we repair in Almaty

Choose your machine brand to see the repair details for that equipment.

We also repairWe also repairTECH SERVICE08

Besides welding machine repair, we fix other equipment in Almaty

Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.

BlogBlogTECH SERVICE09

Worth reading before welding machine repair in Almaty

Leave a review

Choose a platform — the TECH SERVICE page will open.

2ГИС2GISGoogle MapsЯYandex Maps
Send a review with photos on WhatsApp