experience9 yearsRuslan Ts.
Washing machine and refrigerator repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (775) 030 02 94Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Free diagnostics.
Our own technicians4 to 20 years of experience




Repair prices
Below are typical symptoms and likely causes that the technician will check first.
Heating element, sensor, valve
from14 500 ₸
Heating element, thermostat, contactor
from8 500 ₸
Hoses, pump, seal
from9 500 ₸
Drain pump, filter, clog
from14 000 ₸
Fan, bearing, mount
from23 000 ₸
Code points to a component
from18 500 ₸
Lock, seal, steam
from9 500 ₸
Heating element, level sensor
from18 500 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1–2 hourstime
from 8,500 ₸cost

BeforeAfter5 steps

Five steps from request to checking the work after repair.
Submit a request and the technician will come to your site.
The technician lists which components will be disassembled and replaced so you understand the scope of work.
Clear space around the combi oven and remove dishes so the technician can access the panels.
After agreement, the technician performs the work.
The technician explains how to operate the repaired component and what to watch for in the first days.
The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience12 yearsGeneral household appliance repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsExpert washing machine repair technician
experience8 yearsField refrigerator repair technician
experience8 yearsSenior washing machine repair technician
experience11 yearsDishwasher repair technician
experience9 yearsWashing machine repair technician
We reply during working hours
Submit a request for combi oven repair — the technician will come to your site and confirm terms and timing over the phone.

Warranty question? Call us
+7 (775) 030 02 947 898 reviews of repairs at TECH SERVICE in total
Арман К.Order No. ZK-4500 · 10 April 2026
oursЦена имела значение, но и горонтия тоже. Первое, что заметил: не держит температуру. Починили и дали гарантию на месяц.
Талгат С.Order No. 379897 · 25 April 2024
oursДолго откладывал ремант, потом всё-таки собрался. Поставили новую деталь: термопары. Уже полгода — ни одного сбоя.
Ирина Т.Order No. 2024-6688 · 13 January 2024
oursСмотрел, у кого есть запчасти на такую модель. Оставил заявку на ремонт промышленной печи. Больше всего напрягало: не держит температуру. С тех пор ни разу не подвёл.
Карина А.Order No. ZK-6081 · 31 July 2022
oursС чем пришёл: не греет. Никита М принял, посмотрел и сразу сказал, что делать. Работает как раньше, придирок нет
Тимур И.Order No. 337540 · 23 June 2022
oursБыло подозрение, что дело в плате, хотелось услышать второе мнение. Руки чесались починить самому, хорошо, что не полез. Основная жалоба — не греет. Договорились на утро, к девяти уже был свободный мастер. Поставили новую деталь: тэн. Смета совпала с итогом, что редкость. Спасибо за работу. Крутит ровно, без рывков)
Малик Т.Order No. TS-2205-931 · 5 May 2022
oursБыло подозрение, что дело в плате, хотелось услышать второе мнение. Позвонили заранее, предупредили, что задержится на полчаса. Пользуюсь ежедневно, вопросов нет
Нурлан Б.Order No. TS-2105-602 · 25 December 2021
oursДамир М честно сказал, что менять, а что ещё походит. Поменяли: термопары. Шум пропал, работает мягко.
Арман К.Order No. 2021-6211 · 6 December 2021
oursПоломка застала перед командировкой, тянуть было нельзя. Ремонт промышленной печи — вот с этим и пришёл. С чем пришёл: не держит температуру. Под замену пошло: термопары. Включил, проверил, работает.
Бакыт Ж.Order No. TS-2519 · 17 September 2021
oursРаботаю допоздна, поэтому нужен был сервис с нормальным графиком. Настроение было испорчено конкретно. Проблема — не греет. Приехал вечером, мастер ещё был на месте. Разобрали, посмотрели: тэн. Сравнивал с двумя другими — здесь вышло ровнее всех. Гудит ровно, не греется, всё как надо.
Елдос К.Order No. ZK-2021/447 · 1 May 2021
oursБалалар бар, техникасыз қиын, сондықтан тез жөндеу керек еді. Бағасы базардағыдан қымбат емес. Жөндеуге кепілдік бар, сол сенімді.
Ринат Х.Order No. TS-5656 · 12 March 2021
oursБыло важно, чтобы сделали до выходных — гости, то-сё. Основная жалоба — не держит температуру. Проверил дома — всё на месте, ничего не забыли.
Молдир С.Order No. 2020-1085 · 16 October 2020
oursСмотрел, у кого есть запчасти на такую модель. Техника работала годами, а тут — не держит температуру. Дамир М возился с этим дольше, чем планировал, но довёл до конца. Работает даже тише, чем до поломки.
Гульнара Б.Order No. 73503 · 27 September 2019
oursЦена имела значение, но и гарантия тоже. Диагностика промышленной печи — с этого всё началось. Первое, что заметил: не держит температуру. Ораз объяснил причину так, что понял даже я. Поставили новую деталь: тэн. Сначала сказали одно, потом уточнили, но в итоге всё совпало. Сказать, что доволен — ничего не сказать.
Дарья С.Order No. 2019-9395 · 27 May 2019
oursБыло важно, чтобы сделали до выходных — гости, то-сё. Привёз на диагностику: промышленная печь. Жалоба простая: не греет. Ораз приехал в тот же день, хотя был конец смены. Запчасть была в наличии, доплачивать не пришлось. Сказать, что доволен — ничего не сказать
Ринат Х.Order No. 2018-1563 · 26 September 2018
oursНужен был счёт и чек, у нас техника на балансе организации. Сначала сомневался, мало ли что. Жалоба простая: не держит температуру. Поставили новую деталь: контроллер. Сравнивал с двумя другими — здесь вышло ровнее всех. Мастер сразу сказал, что к чему, без размытых формулировок. Очередь была, посидел минут двадцать. Однозначно да. Вернули в тот же день, всё функционирует.
Елена К.Order No. 58047 · 24 June 2018
oursБалалар бар, техникасыз қиын, сондықтан тез жөндеу керек еді. Ескі бөлшекті қайтарып берді, әдетте олай жасамайды. Нәтижесіне ризамын)
Сабина Г.Order No. ZK-4763 · 8 November 2017
oursПервое, что заметил: не держит температуру. Отдельно спасибо мастеру — Никита М, терпения ему хватило. Уже полгода — ни одного сбоя
Гульнара Б.Order No. 2017-6274 · 11 February 2017
oursБольше всего напрягало: не греет. Ораз помог выбрать, без навязывания. Починили и дали гарантию на месяц
Ринат Х.Order No. 2016-6093 · 14 December 2016
oursПрочитал кучу отзывов, половина — реклама, но тут вроде живые. Проблема — не держит температуру. Работает даже тише, чем до поломки
Гульмира С.Order No. TS-1606-832 · 31 August 2016
oursҮйдегілер «лақтыр» деді, мен шешім қабылдамай тұрып көрсетуге апардым. Кепілдік мерзімі біткен соң бұзылды, әрине.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionIt's impossible to say without looking: the heating element, the sensor, or the contactor could all be at fault. The exact answer comes from a free on-site diagnosis, after which the technician identifies the cause and the scope of work.
Most often it's a shorted heating element, moisture on the contacts, or faulty wiring. Until the cause is found, it's best not to turn the unit back on to avoid damaging the electronics.
First, check if there's water in the system and if the steam generator is clogged with scale. If the water supply is fine but there's no steam, it's likely the heating element or the valve, and you'll need a technician.
On Unox, this code is usually related to the steam generator or sensors, but the interpretation depends on the model. A technician can decode it and find the cause after inspecting the unit.
It depends on the model and the type of damage: sometimes it's enough to replace a burned-out component or restore the traces. The technician decides after disassembling and checking the board.
The key is the condition of the steam generator and electronics: if scale has corroded the components and the board needs serious restoration, repair may not be worthwhile. The technician will assess this during diagnostics and suggest a solution.
Tech Service repairs convection ovens in Almaty as a direct provider: our technician comes to your home or picks up the equipment for service. Diagnostics are free, we arrive within 60 minutes anywhere in the city, and you get a 1-year warranty on labor and parts. The technician gives you the price after diagnostics.
The symptom is just the tip of the iceberg. Before calling a technician, it helps to understand what's behind the complaint: the conversation becomes more specific, and you can narrow down the fault before the specialist even arrives.
Most often the chamber doesn't reach temperature because of the heating element, the temperature sensor, or the contactor that isn't supplying power to the heating element. The logic is simple: the heating element converts current into heat, the sensor reports the actual temperature to the control board, and the contactor closes the circuit on its command — a failure in any link leaves the chamber cold while the automation still runs. You can hardly tell them apart by ear, but the owner can do a quick check in a couple of minutes. The fan circulates air through the chamber, so if the airflow is fine but the heater is dead, you'll hear the usual hum without a single degree of heat. If the whole unit is silent when turned on, the power circuit breaks earlier — check the fuse and the power supply. It's easy to check: if the fan runs but there's no heat, look for the cause in the heating circuit; if the fan is silent too, start with the power supply and fuse. If your own check doesn't solve it, a technician repairs convection ovens in Almaty after free diagnostics.
The code on the display is a hint, not a verdict: E03 usually points to a problem with the sensor or the heating circuit, E15 to a fault in the steam supply unit or overheating. Numbering shifts between manufacturers, so the code is read together with the model and firmware version. In practice, E03 is linked to a break or oxidation in the temperature sensor's signal line, less often to a failed contactor on the control board. E15 more often appears in the steam generator circuit: a steam sensor clogged with scale or a triggered overheat protection. The control board compares sensor readings with setpoints and blocks heating when they go out of range — that's why the unit stops long before an obvious breakdown. Write down the code and model before calling the technician: it makes it easier to bring the right part straight away and avoid servicing the equipment twice.
Steam leakage is usually a worn door seal, no steam means scale or a failed steam generator heating element, and a tripped breaker means a short circuit in the cable, the heating element, or after a power surge. Over time the seal hardens and stops pressing the door shut, so steam escapes around the perimeter instead of into the chamber. Scale on the steam generator's heating element reduces heat transfer, so steam output drops or stops completely. The breaker trips when the power cable insulation breaks down, the heating element coil short-circuits, or after a power surge that damages the fuse and control board. Moreover, when the protection trips right after turning on, restarting finishes off the control board — in that situation the equipment already needs a technician, not DIY attempts. If the breaker trips again, don't replace it with a more powerful one: that only removes the protection while the cause of the short circuit remains.
Humming and unusual noise usually come from the fan and blower motor, while spontaneous shutdown comes from overheating, a faulty temperature sensor, or protection that trips when the circuit is faulty. Worn blower motor bearings produce a growing hum, and an unbalanced impeller causes vibration and knocking. Shutdown under load points to thermal protection reacting to real overheating or to distorted sensor readings. The control board detects the spike and shuts down the unit to avoid burning the windings and wiring. When the equipment shuts off under load rather than immediately, it's usually thermal protection — don't ignore it, repeated restarts accelerate wear on components and bring the blower motor closer to replacement. Note how many minutes after start the unit cuts out: that interval helps the technician pinpoint the overheating component more accurately.
A combi oven is heavy and bulky, so it's not always clear whether it can be fixed on site. Here's what a mobile technician can handle and what requires bench testing at the service center.
If the problem is in the steam generator, a heating element with scale, or the control board needs soldering, the equipment is taken to the service center, where it is disassembled and tested on site. The steam generator requires opening the casing, removing the boiler, and assessing the scale layer on the heating element: this can't be done in a kitchen without risking damage to seals and wiring. A control board with microcracks and signs of overheating is tested on a bench under load, not just by visual inspection. We carry out repairs at the service center when fixing the cause on site is impractical or impossible — and return the unit with all modes checked. Don't agree to 'blind work' without diagnostics — the technician must first name the cause, and only then discuss the scope and place of replacement.
Our diagnostics are free: a technician arrives within 60 minutes anywhere in the city, finds the cause, and only then quotes the cost of work. First, they inspect the unit, check the power, sensors, and door condition, then run the chamber in test modes and note at which stage the failure or error code appears. Based on the results, you get a clear explanation: which component failed, and whether it can be fixed at home or requires a trip to the service center. Ask the technician which components they checked and why they name this cause — a clear explanation helps you avoid paying for unnecessary work. We agree on the cost of work and parts before starting, and a 1-year warranty covers both labor and parts.
| What happened | Where we fix it | What the technician does |
|---|---|---|
| Seal, door handle | at home | replaces the part |
| Power, fuse | at home | checks the circuit |
| Sensors, control board | at home or at the service center | tests; takes it in if soldering is needed |
| Steam generator, scale | at the service center | disassembles, cleans, replaces the heating element |
| Chamber heating element | at home or at the service center | checks the heating circuit |
Different brands fail in their own ways, and the brand often hints at which component is involved. Here's what we work with and what to look for when the equipment breaks down.
| Brand | Common component | What we check | Service format |
|---|---|---|---|
| Rational | temperature sensor, heating element | heating circuit, control board | on-site or in workshop |
| Unox | steam generator, control board | error codes E03, E15 | workshop if steam unit is involved |
| Abat | steam supply, scale buildup | steam generator heating element | workshop |
| Angelo Po | door seal, handle | door, power supply | on-site |
| Tecnoeka | fan, sensors | airflow, heating | on-site or in workshop |
Rational units more often have issues with the heating circuit and temperature sensor, while Unox tends to suffer from the steam unit and the control board that triggers codes E03 and E15. On Rational, we first test the heating element and compare sensor readings with the actual chamber temperature: a mismatch explains both underheating and false errors. On Unox, we inspect the steam generator separately — code E03 points to the water supply circuit and board condition, while E15 indicates a temperature sensor or ribbon cable contact issue. The control board on both brands is sensitive to moisture and voltage spikes, so we assess its condition before replacing the heater. For these brands, it's important not to replace components at random: first identify the source of the error — sensor, board, or the heater itself — otherwise a new part will burn out for the same reason.
Abat more often has problems with steam supply and scale, Angelo Po with door mechanics, and Tecnoeka with airflow and sensors. On Abat, the steam generator heating element gets scaled up and overheats, so when customers complain about weak steam, we check the heater condition and the patency of water supply channels. On Angelo Po, a worn door seal causes heat and moisture leaks: the chamber struggles to maintain settings, and the handle and hinges loosen from constant opening. On Tecnoeka, fan failure shows up as uneven heating and airflow errors, and sensors eventually start giving inaccurate temperature readings. If the equipment is used in a busy kitchen, preventive maintenance for these brands should be planned in advance rather than after a breakdown — scale and mechanical wear accumulate gradually.
Most service calls for combi ovens are related to scale in the steam generator and operating errors. Here's how to spot buildup in time and what to do to make the steam unit last longer.
We recommend cleaning the steam generator regularly, using water of suitable hardness, and not leaving the chamber with grease residue after a shift. Prevention starts with water: the softer the water entering the unit, the slower scale builds up and the more stable the temperature remains. The second most important element is the door seal: a dirty or stiff seal lets moisture escape, the chamber takes longer to reach the set mode, and the sensor works under overload. Every shift, wipe grease off the walls and tray, rinse the chamber, and check that the water supply nozzles are not clogged. Every few months, inspect the filter and the unit itself—this is easier than taking it apart when it is clogged. In our practice, the majority of failures are due to neglected deposits, not manufacturing defects. It is convenient to combine prevention with scheduled maintenance before the busy season—so the equipment breaks down less often at the worst possible moment.
If steam is still weak after cleaning or the steam generator's heating element is broken, it's no longer about prevention but about replacing the unit. You can tell one from the other by how the appliance behaves: with scale, steam simply weakens; with a broken heating element, errors appear and protection trips. In such a situation, the steam sensor reads incorrect values, and the control board puts the appliance into error or blocks startup. We replace the steam generator's heating element and check the condition of the sensor and control board—after a breakdown, they often show signs of overheating. It's important not to delay: running a broken unit damages the electronics, and replacing the heater is then compounded by restoring the board. The check takes little time, but the difference in consequences is significant.
A warranty is not a formality but a clear set of obligations. Below we explain what obligations we take on, how to proceed if the problem recurs, and where the line for a warranty case is drawn.
We provide a 1-year warranty on labor and parts—if the unit fails again within this period due to our fault, we'll fix it at no extra cost. The obligation covers both components at once: the technician's work and the part they installed. In our experience, disputes are rare, and almost always they are not related to the repair itself but to another unit that was working at the time of diagnosis. Therefore, at Tech Service we record which unit and which part were replaced—this makes it easier to distinguish a warranty case from a new breakdown. Keep this information—with the unit and part details, the technician can more easily confirm that the request is covered by the warranty.
If the same error comes back after service, we recheck the cause: sometimes the code points not to the replaced unit but to a related fault that appeared later. Code E03 usually indicates heating problems, E15—overheating or a temperature sensor fault, but the same code on the display does not always lead to the same culprit. Behind the control board there may be an oxidized contact, and behind the temperature sensor—damaged wiring. On a repeat visit, the technician goes through the entire chain again, not just the part they touched last time. Describe to the specialist under what conditions the error appears—at startup, during steam generation, or under load—this narrows down the search.
| What was checked | Covered by warranty | Term |
|---|---|---|
| Replacing the steam generator heating element | yes, labor and part | 1 year |
| Repairing the control board | yes, labor and part | 1 year |
| Replacing the door seal | yes, labor and part | 1 year |
| A unit that was not touched | no | — |
Before calling, it's useful for the owner to understand two things: who exactly will step into the kitchen and how the booking process works. We tell you about our technicians and the stages of work.
Tech Service is a direct service provider: our technician comes to you, not a contractor from an aggregator, so we stand behind the work and the warranty. The same service that takes your request is the one whose specialist later opens the combi oven panel — there's no third party between the dispatcher and the field technician who resells the call and adds their own margin. The 1-year warranty covers both labor and parts, and you claim it from us, not from an outside organization that simply passed the order along. In practice, if a breakdown happens again, you go back to the same provider with the same obligation, rather than starting a conversation with a new contractor. Ask who the provider is and who handles warranty claims — with a middleman, responsibility often gets blurred between the dispatcher and the technician.
Our technicians have 4 to 20 years of experience and arrive within 60 minutes anywhere in the city. That range in experience is no accident: combi ovens of different generations are built differently, and a technician with more experience recognizes a familiar fault faster by the sound of the pump or the pattern of the error on the display. The 60-minute response works across all of Almaty, not just the central neighborhoods — that's convenient when equipment sits in a hot kitchen and downtime holds up the whole shift. In my experience, the cause takes longest to find when the symptom is described vaguely, without the code on the panel. If the equipment is in a kitchen during peak hours, schedule the visit in advance — that way the technician arrives when the chamber is free.
To request service, just provide the model, error code, and symptom — we'll agree on a time, the technician will come, run free diagnostics, and quote the cost of work. Diagnostics are free, so the inspection costs nothing even if the fault turns out to be minor and there's nothing to fix. The combi oven model and the code on the display are the first things to provide: with them, the technician prepares tools in advance and understands the type of unit involved. The cost is agreed after the inspection, not over the phone — the amount depends on the failed component. You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies, so you choose how to pay. Decide in advance whether a home visit works for you or if it's better to bring the equipment to the service center — that will speed up scheduling.
Understanding the breakdown, the type of work, and warranty terms helps equipment owners make decisions without rushing or overspending. Below is a short summary to keep in mind before contacting a technician.
9brands
Choose a brand to see its models and repair details.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your dishwasher won't drain, the most common culprits are a clogged filter or drain hose; less often, it's the pump, impeller…
24 March 2026 · 12 minutes read
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
The easiest way to remove scale from a kettle is with citric acid: 1–2 tablespoons per liter of water, boil for 5–10 minutes, then drain and rinse.
17 March 2026 · 13 minutes read
If your laptop screen is broken, turn the device off first, don't press on the display, and check the picture through an external monitor.
12 March 2026 · 11 minutes read
Air conditioner errors are codes on the display or flashing indicators that show which component has failed.
5 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read












