Open until 19:00+7 (778) 746 00 26Call a technician
Tech Service technician next to a refrigerator

Goldstar Refrigerator Repair in Almaty

A technician arrives within 60 minutes anywhere in the city. Free diagnostics.

  • 1-year warranty on labor and parts
  • Technicians with 4 to 20 years of experience
  • You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies

Our own technicians4 to 20 years of experience

Ruslan Ts.Dilmurat S.Nikita M.Damir M.

Repair prices

  • Diagnostics0 ₸
  • Drain line cleaningfrom5 000 ₸
  • Defrost timer / sensor replacementfrom6 000 ₸
  • Door rehanging / adjustmentfrom6 500 ₸
  • Door seal replacementfrom7 500 ₸
All prices
2ГИСЯours4,97 898 reviews
2GIS · Google · Yandex · order database
Common faultsCommon faultsTECH SERVICE02

Common Goldstar refrigerator faults in Almaty

The issues refrigerator owners call us about most often. The technician confirms the exact cause during diagnostics.

PricesPricesTECH SERVICE03

How much Goldstar refrigerator repair costs in Almaty

The table shows what a Goldstar refrigerator repair costs: the labor price "from" without parts and the time it takes, and the technician confirms the final amount before starting the repair.

Drain line cleaninglabour only

1–2 hours

from5 000 ₸

Defrost timer / sensor replacementparts not included

1–2 hours

from6 000 ₸

Door rehanging / adjustmentlabour only

1–2 hours

from6 500 ₸

Door seal replacementparts not included

1–2 hours

from7 500 ₸

Filter drier replacementrefrigerant not included

1–2 hours

from7 500 ₸

Before and afterBefore and afterTECH SERVICE04

Before and after Goldstar refrigerator repair in Almaty

Not holding temperature due to thermostat

1 visittime

from 9 500 ₸cost

Problem
The Goldstar refrigerator stopped holding temperature: the compressor either would not turn on or ran without stopping — the thermostat is faulty.
What we did
The technician opened the thermostat housing in the chamber, replaced the thermostat and connected the wires, checked the compressor turning on and off.
Result
The refrigerator holds temperature again, the compressor turns on and off as it should. Warranty — 1 year for labor and parts.
I want the same
In a kitchen with light gray fronts, a white refrigerator with glass shelves is open; a technician in an orange shirt holds a thermostat with wires near the open thermostat housing inside the compartment.BeforeAfter
01 / 05
All repairs
TECH SERVICE mobile technician with a tool case

How Goldstar refrigerator repair works at your home in Almaty

Five steps from your request to checking that the refrigerator works.

  1. Requestsame day you call

    Describe the symptom and your refrigerator model so the technician brings the right tools.

  2. Technician visitwithin 60 minutes

    The technician confirms the model and symptom by phone, then brings tools and common parts for your brand.

  3. Preparing accessbefore the visit

    Agree on a convenient time and clear access to the refrigerator so the technician can work quickly.

  4. Confirming the workafter inspection

    The final list of work is recorded in the request, and the technician hands the replaced part to the owner.

  5. Checkafter repair

    The technician starts the refrigerator, checks the cooling, and shows you that it works.

Leave a request
TechniciansTechniciansTECH SERVICE05

Our Goldstar refrigerator repair technicians in Almaty

The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

  • 8 technicians in Almaty
  • 8–12 years of experience in the department
  • Article author Ruslan Ts., 9 years of experience
Technician repairing a refrigerator at a customer’s home
Field technician at a customer’s home

The department has 8 specializations — they are listed on the technicians' cards.

01 / 05
Ruslan Ts., washing machine and refrigerator repair technicianexperience9 years

Ruslan Ts.

Washing machine and refrigerator repair technician

Dilmurat S., field technician for washing machine and refrigerator repairexperience10 years

Dilmurat S.

Field technician for washing machine and refrigerator repair

Nikita M., field refrigerator repair technicianexperience8 years

Nikita M.

Field refrigerator repair technician

Damir M., general household appliance repair technicianexperience12 years

Damir M.

General household appliance repair technician

Dima, expert washing machine repair technicianexperience8 years

Dima

Expert washing machine repair technician

We reply during working hours

Book Goldstar refrigerator repair in Almaty

Describe the issue and a convenient time for the visit. The technician will come, check the cause on site, and agree on next steps with you.

TECH SERVICE administrator replying to a customer's WhatsApp message

Warranty question? Call us

+7 (778) 746 00 26
Customer reviewsReviewsTECH SERVICE06

Reviews of Goldstar refrigerator repair in Almaty

Алексей Г.Order No. TS-2501-114 · 4 August 2025

ours

Работаю допоздна, поэтому нужен был сервис с нормальным графиком. По деньгам вышло адекватно, в другом месте просили больше. Уже полгода — ни одного сбоя)

Repair: refrigerator

Ерасыл Б.Order No. 954197 · 13 August 2021

ours

Техника на гарантии уже не была, так что выбор был свободный. Честно говоря, доверяю больше тем, кто говорит по делу. Симптом был очевидный: течёт. Из деталей — термостат. Вышло 20 000 тенге, дешевле, чем я рассчитывал. Ответили быстро, не пришлось ждать на линии. Техсервис на Абая, если не ошибаюсь, — вот туда и поехал. Уже полгода — ни одного сбоя.

Repair: refrigerator

Азамат Е.Order No. 20528 · 1 May 2021

ours

Друг посоветовал, у него похожая история была. Первое, что заметил: течёт. Починили и дали гарантию на месяц.

Repair: refrigerator

Бекзат Т.Order No. ZK-2020/226 · 1 August 2020

ours

Смотрел, у кого есть запчасти на такую модель. Обидно было, техника не старая совсем. С чем пришёл: намерзает лёд. Никита М возился с этим дольше, чем планировал, но довёл до конца. Сделали и забыл про проблему.

Repair: refrigerator

Сергей Р.Order No. 598321 · 25 April 2020

ours

Выбирал по отзывам в 2ГИС, времени на эксперименты не было. До последнего откладывал, но пришлось признать: шумит. Могли бы взять больше, но взяли по-божески. Заявку приняли по телефону, перезвонили через десять минут. Деталь на замену — уплотнитель. Пять звёзд, не задумываясь. Ребёнок уже проверил на прочность, держится.

Repair: refrigerator

Светлана Д.Order No. ZK-2019/136 · 30 May 2019

ours

Было подозрение, что дело в плате, хотелось услышать второе мнение. Честно, уже готовился покупать новое, но обошлось. Проблема — шумит. Проверил дома — всё на месте, ничего не забыли.

Repair: refrigerator

Павел Ш.Order No. 2018-7272 · 9 January 2018

ours

Симптом был очевидный: шумит. Дильмурат С честно сказал, что менять, а что ещё походит. Шум пропал, работает мягко.

Repair: refrigerator

Аяна Е.Order No. 25364 · 9 December 2017

ours

Отдал мастеру: холодильник. Жалоба простая: шумит. Никита М объяснил причину так, что понял даже я. Смета совпала с итогом, что редкость. Поставили новую деталь: термостат. Мастер сразу сказал, что к чему, без размытых формулировок. Нагрев в норме, посторонних звуков нет.

Repair: refrigerator

Акбота Т.Order No. ZK-2520 · 13 April 2016

ours

Проблема — шумит. Никита М подсказал, как продлить жизнь технике. Починили и дали гарантию на месяц.

Repair: refrigerator

Сергей Р.Order No. ZK-8150 · 20 March 2016

ours

Хотел сначала вызвать мастера на дом, потом передумал. Нужен был ремонт холодильника — обратился сюда. Основная жалоба — шумит. Всё оформили по договору, с печатью. Заодно поменяли: термостат. Вышло 34 500 тенге, дешевле, чем я рассчитывал. Однозначно да. Проверил дома — всё на месте, ничего не забыли.

Repair: refrigerator
See all reviews
Questions and answersQuestionsTECH SERVICE07

Questions about Goldstar refrigerator repair in Almaty

Didn’t find the answer? Message us on WhatsApp.

Ask a question
Can a Goldstar refrigerator compressor be replaced at home in Almaty?

Yes, the technician replaces the compressor on-site if the unit is accessible: they do the brazing and refrigerant recharge. Whether it's possible depends on the model and design of the refrigerator.

The Goldstar refrigerator clicks and won't start — is it the compressor or the start relay?

More often it's the start relay: it clicks as it tries to start the compressor, but the compressor doesn't kick in. The exact answer comes from free diagnostics — the technician checks the compressor windings and the relay.

Why does the Goldstar refrigerator run nonstop and never shut off?

The causes are a refrigerant leak, a faulty thermostat or sensor, compressor wear, or a loose door seal. It depends on the model, so an on-site diagnosis is needed.

Can an old Goldstar refrigerator be repaired, or is it easier to buy a new one?

Old Goldstar units are repaired if the component is accessible and replacement makes sense: compressor, thermostat, seal. The technician explains the decision after free diagnostics, once the cause of the breakdown is clear.

What should I do if the Goldstar refrigerator builds up ice on the back wall?

Frost points to a defrost or sensor failure, or a door that isn't closing tightly. Check whether the seal fits snugly and whether the drain is blocked, and if the ice keeps growing, you need a technician.

There's a refrigerant leak in the Goldstar refrigerator — how does the technician find and fix it?

The technician checks the circuit for leaks, locates the leak, seals it, and recharges the system with refrigerant. The method of finding it depends on the refrigerator model.

Repair guideArticleTECH SERVICE08

Goldstar Refrigerator Repair in Almaty with Technician Visit

Ruslan Ts., washing machine and refrigerator repair technician

Author: Ruslan Ts.,Washing machine and refrigerator repair technician

Published
Updated

Tech Service repairs Goldstar refrigerators in Almaty at home or at the service center. A technician arrives within 60 minutes anywhere in the city, diagnostics are free, and we provide a 1-year warranty on labor and parts. The technician names the cost after diagnostics, and you can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies.

Why Your Goldstar Refrigerator Isn't Cooling and What the Symptoms Tell You

A Goldstar refrigerator usually signals a specific symptom, and that can narrow down the faulty components even before the technician arrives. Let's look at three typical scenarios.

Refrigerator Not Cooling but Light Is On

  • Power is fine: if the light inside comes on, the unit is receiving voltage, so the cause is likely in the cooling circuit.
  • Compressor under suspicion: a humming motor may not be building enough pressure, so 'running but not cooling' doesn't mean the compressor is fine.
  • Refrigerant leak: when the refrigerant circuit loses its seal, cooling drops and the compartment warms up gradually, not all at once.
  • Start relay: a worn part can prevent the motor from reaching operating mode, leaving the compartment warm while the light stays on.
  • What to tell the technician: describe whether the unit hums and how long the cooling has been gone — this speeds up troubleshooting.

Clicking, Humming, or Running Nonstop

  • Clicking without starting: most often this points to a worn start relay — it opens but the motor doesn't start.
  • Running without stopping: continuous humming suggests a thermostat that isn't signaling for a break, or a refrigerant leak.
  • Humming after defrosting: often the source is the compressor mounting, not the unit itself, and that changes the scope of work.
  • Thermostat and temperature control: a sensor that has lost accuracy keeps the compartment in constant freeze mode or doesn't turn on cooling at all.
  • What to tell the technician: the type of sound and when it occurs hint at which component to check first.

Ice Build-Up and Frost on the Back Wall

Ice on the back wall and excessive freezing are usually linked to the defrost system, door seal, or temperature control. When defrost doesn't kick in, moisture settles on the evaporator and gradually turns into frost, and the fan stops distributing cold air evenly. If the seal doesn't fit tightly, warm air constantly gets inside, and the frost returns even after a full defrost — the motor has to run longer. A temperature control that has lost accuracy keeps the temperature above the set point, so food in the upper part of the compartment starts to thaw and a crust builds up on the wall. In my experience, the seal is the most underrated culprit: its wear quietly brings frost back even after defrosting. Check how tightly the door fits with a sheet of paper — if it slips out without resistance, show the unit to a technician.

Goldstar Error Codes and How a Technician Finds the Fault

A signal on the display narrows the search to a specific component, but the specialist makes the final call after testing. Let's look at what the screen shows and how measurements confirm the fault.

What the Error Code on the Display Means

  • Control board: generates the signal and displays it when a component's readings go beyond the operating range.
  • Temperature sensor: if the circuit is open or shorted, the module detects a fault and shows a code.
  • Group of components: the symbols point to the entire circuit, not a specific part inside it.
  • Decoding by table: the code is tied to a section of the circuit but doesn't name the culprit directly.
  • Measurement instead of the screen: the specialist checks the sensor's resistance and the circuit's power to separate a module fault from a part fault.
  • Repeatability: if the signal reappears after a restart, it confirms a fault rather than a random glitch.

How to Tell If It's the Compressor or the Thermostat

  • Startup behavior: our technician listens to whether the motor starts and keeps running, rather than relying on a single symptom.
  • Measurements at components: diagnostics show the pressure in the circuit and the resistance of the thermostat circuit before any work begins.
  • Thermostat: if the compartments don't shut off while the motor runs properly, the thermostat or temperature sensor is usually to blame.
  • Compressor: humming without starting, clicking, and no pressure point to the motor-compressor itself.
  • Sensor: fluctuating temperature readings while the motor runs are often caused by the temperature sensor, not the thermostat.
  • Conclusion: when the motor starts and holds pressure but the compartments don't shut off, there's no need to replace it.

How a technician finds a refrigerant leak

We find refrigerant leaks by pressure drop in the circuit and by inspecting connections, then fix the leak before recharging. The technician checks joints, the capillary tube, and the evaporator, looking for oil traces and corrosion spots on the cooling circuit. With the motor running, cooling doesn't disappear at once: gas escapes gradually, and the compartments warm up over several days. Our diagnostics are free, so the leak is located before any work. Simply topping up refrigerant without finding the leak makes no sense—the gas will escape again through the same connection, so we fix the cause first and then recharge the circuit. Finding the leak is hardest in the foamed part of the cabinet—there visual inspection doesn't help, and the point is determined by the pressure difference between sections. Refrigerator repair for Goldstar in Almaty starts with this kind of leak detection to avoid recharging the circuit again.

Common Goldstar refrigerator breakdowns and their repair

Like any brand, Goldstar has components that fail more often than others. Below is what breaks, which symptom reveals it, and what the technician checks.

Which components fail most often

ComponentTypical symptomWhat we check
Compressornot cooling, hummingstartup and circuit pressure
Start relayclicking, won't startcontacts and motor startup
Thermostatwon't shut offtemperature response
Refrigerant leakcooling lostpressure and circuit connections
Defrost systemice buildupheating and defrost timer
Fannoisy, compartment warmrotation and bearing

Can a compressor be replaced on-site?

We replace the compressor at the customer's home if access to the part allows; otherwise, the work is done at our service center. The motor compresses refrigerant and circulates it through the cooling circuit, so when it fails, both compartments stop cooling. Before work, the technician checks the start relay and circuit pressure: if the contacts are fine but there's no pressure, the part is replaced along with leak detection. In a tight niche or with built-in appliances, it's easier to remove the component on-site and braze the circuit at the service center—that way, joint tightness is easier to verify. After replacing the compressor, the circuit is checked for leaks; otherwise, the new part will quickly fail due to the same leak. We provide a 1-year warranty on labor and on the installed component.

How servicing an inverter Goldstar differs

  • Control board: in an inverter model, it sets the compressor speed, so diagnostics start there, not with the relay.
  • Compressor: the inverter motor smoothly varies power, and its failure often looks like an electronics error.
  • Error code: the board displays a code, and the technician uses it to narrow down the circuits to check.
  • Check before replacement: an electronics fault can look like a "dead" motor, so replacing it without checking the board is risky.
  • Temperature sensors: inverter models have several, and mismatched readings disrupt the cooling mode.

How Goldstar refrigerator repair in Almaty works from request to warranty

The process follows clear steps — from request and visit to approval and warranty. Let's walk through each stage so you know what's happening with your appliance and when.

Request and technician visit within 60 minutes

After you request a visit, our technician arrives at your home within 60 minutes anywhere in the city. The on-site specialist inspects the appliance right there, so most faults are identified on the spot. Goldstar refrigerator repair in Almaty starts with an accurate on-site diagnosis, so the technician immediately assesses the condition of the components. You can request a visit by phone or on the website: just provide the Goldstar model and describe how the cooling behaves. The specialist will ask whether the light inside is on, if there's a click when it starts, and if there's frost on the back wall — these details narrow down the causes even before the visit. Before the technician arrives, please clear access to the back of the refrigerator — this makes diagnosis faster.

Free diagnostics and work approval

We provide diagnostics free of charge and then agree on the list of works and the cost with the client. The specialist checks the thermostat, compressor, start relay, and pressure in the circuit to pinpoint the faulty component rather than replacing parts at random. Based on the inspection, the client receives a list of what needs to be fixed or replaced and decides which works to proceed with. The specialist quotes the price after diagnostics because it depends on the specific component, not on the brand as a whole — replacing a relay and working on the circuit differ in labor. Approval happens before any work begins: we don't start until the client confirms the list. If an additional fault is found during the inspection, it's also added to the list and approved separately so the final amount doesn't come as a surprise.

Repair at home or at the service center

  • At home: replacement of the thermostat, start relay, seal, and sensors is done on-site without transporting the appliance.
  • At the service center: complex disassembly or work on the circuit is performed in the workshop, where the appliance is delivered for repair.
  • Choosing the format: the specialist suggests an option after inspection based on the component and access to it, not by a template.
  • 1-year warranty: covers both labor and parts regardless of where the work was done.
  • Payment: you can pay by Kaspi QR, Kaspi Red, card, cash or bank transfer, and the specialist quotes the price after free diagnostics.

What you can check yourself and when you need a technician

The owner of a Goldstar can rule out some causes in a couple of minutes, while others require tools and a technician visit. Let's separate the checks you can do yourself from the cases where a specialist is essential.

What to check before calling a technician

  • Power supply: make sure the outlet works and the plug fits snugly — poor contact causes startup issues.
  • Thermostat: check that the knob isn't set to minimum and hasn't been accidentally moved while cleaning the compartments.
  • Door seal: inspect the edge for gaps and frost — a loose seal causes ice buildup and loss of cooling.
  • Loading the compartments: packing too much food blocks air circulation between shelves and at the back wall.
  • Defrosting: if your model isn't No Frost, check if there's a thick layer of frost and whether it's time to defrost the appliance completely.
  • Result of checks: if the refrigerator behaves the same after these steps, the cause is inside the components and you need a technician.

When you need a technician, not self-checks

You need a technician when the refrigerator doesn't cool but the light is on, clicks without starting, or runs without stopping. The symptom 'clicks and doesn't start' most often points to the start relay or compressor, while continuous operation without pauses indicates a thermostat or refrigerant leak. These components can't be checked visually: you need a manifold gauge, a multimeter, and access to the cooling circuit. Trying to disassemble the compressor compartment without tools and skills usually damages the components. If the symptom persists after self-checks, the next step is an on-site diagnosis — it shows which component has failed. Around the city, a technician visit takes about 60 minutes, and at the address they confirm or rule out the preliminary diagnosis.

Repair an old Goldstar or replace it

An old Goldstar fridge is worth restoring if only one component is faulty and the body and circuit are intact. The decision to replace is based not on the age of the appliance but on the condition of the cooling circuit and the number of broken components. If the compressor, relay, or thermostat has failed, replacing the component restores cooling without affecting the rest of the system. When the tubes and evaporator are free of corrosion, restoration preserves the unit's lifespan. If several components are faulty at once and the circuit is damaged, replacement may be more sensible. Diagnostics identify the faulty component before work begins and show what needs to be replaced. The final decision is made after inspection, not based on external signs or the year of manufacture. The technician explains which components still have life left and which will soon need attention, and offers restoration only where it is justified by the condition of the circuit.

Warranty and why a direct contractor is more reliable

When choosing who will repair your fridge, two things matter: what the obligations cover and who exactly will come on the request. Let's look at how this works in practice.

1-year warranty on labor and parts

We provide a 1-year warranty on labor and parts. If after a few months the compressor or start relay fails again, you come back to us and we fix the issue under warranty. The labor coverage is responsible for the quality of soldering, connections, and adjustments of components, while the parts coverage is for the component itself. Both periods run in parallel, so both the work and the installed part remain under the service's obligation. The parts obligation is important because a part can fail on its own—then it is replaced under warranty, not at the customer's expense. Ask the technician what exactly the warranty covers—labor and parts. This is especially important when replacing a compressor or another expensive component: coverage for the part and its installation applies equally, so a repeat failure does not become a new expense for the owner.

Direct contractor, not an aggregator

  • Our own field specialist: our technician arrives on the request, not a third-party contractor.
  • Single responsibility: one party holds the work and obligations, so there is no dispute about who is responsible for defects.
  • Direct contact: you discuss the issue with the person who will service the fridge, without an intermediary.
  • No middleman: there is no aggregator between you and the contractor, so the same company that handles the request also does the repair.
  • Verifiable trail: the request, diagnostics, and obligations stay within one company, without intermediaries.

Technician experience and payment

Our technicians have from 4 to 20 years of experience, and you can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies. Such experience means the specialist has already seen various manifestations of breakdowns and can quickly narrow down the causes during inspection. Diagnostics are free: the technician arrives, finds the cause, and only then names the cost of work. City visits within 60 minutes. In my opinion, diagnostics show the specialist's level: a novice replaces parts one after another, while an experienced person narrows it down to one or two components and doesn't touch working ones. So when requesting service, ask not only about the price but also about experience with your specific model—this will tell you how confidently the technician knows your series.

Key points on Goldstar refrigerator repair

Diagnosing Goldstar breakdowns comes down to a few recurring scenarios, and understanding the troubleshooting logic helps you get to the cause faster and avoid replacing unnecessary parts.

  • No cooling but the light is on: narrows the search to the compressor, start relay, or refrigerant leak, not the electronics.
  • Error code on the display: outlines a group of components, but the exact cause is confirmed by pressure and winding resistance measurements.
  • Common issues for the brand: compressor, relay, thermostat, and refrigerant leak are the four components responsible for most failures.
  • Self-check: helps rule out simple issues, but clicking, humming, and nonstop operation require a technician's diagnosis.
  • Choosing a service provider: what matters is the warranty on labor and parts and who exactly will come to your address.

90brands

Besides Goldstar, we repair other refrigerator brands in Almaty

We work with every brand sold in Kazakhstan — from Samsung, LG and Atlant to Biryusa, Indesit, Stinol and rare imported makes. Can’t find yours in the list? Call anyway — a technician will come and take a look.

We also repairWe also repairTECH SERVICE09

Besides Goldstar refrigerator repair, we fix other equipment in Almaty

Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.

BlogBlogTECH SERVICE10

Worth reading before Goldstar refrigerator repair in Almaty

Leave a review

Choose a platform — the TECH SERVICE page will open.

2ГИС2GISGoogle MapsЯYandex Maps
Send a review with photos on WhatsApp