experience9 yearsRuslan Ts.
Washing machine and refrigerator repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 746 00 26Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Free diagnostics.
Our own technicians4 to 20 years of experience




Repair prices
Below are typical symptoms and likely causes. The technician will determine the exact cause during free diagnostics.
refrigerant leak, compressor wear
from10 500 ₸
temperature sensor failure
from6 000 ₸
clogged drain, damaged door seal
from5 000 ₸
sensor or control board malfunction
from11 500 ₸
compressor wear, loose mounts
from24 500 ₸
No Frost failure, defrost sensor breakdown
from6 000 ₸
power interruption, start relay failure
from7 500 ₸
worn seal, misaligned hinges
from7 500 ₸
The table shows the starting labor cost without parts and the repair time for Gorenje refrigerators; the technician confirms the final amount before any work begins.
1 visittime
from 6 500 ₸cost

BeforeAfter5 steps

Five steps from request to performance check.
Submit a request by phone or messenger and describe the symptom.
Confirm your address and access to the appliance by phone so the technician arrives prepared.
The technician checks the appliance and identifies the cause of the breakdown.
The technician performs the repair on-site; if the needed part is not on hand, they will arrange a follow-up visit.
The technician starts the refrigerator and monitors the temperature to confirm it works.
The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsField refrigerator repair technician
experience12 yearsGeneral household appliance repair technician
experience8 yearsExpert washing machine repair technician
We reply during working hours
Submit a request — diagnostics are free. 1-year warranty on labor and parts.

Warranty question? Call us
+7 (778) 746 00 267 898 reviews of repairs at TECH SERVICE in total
Асель Ж.Order No. 2026-4630 · 5 February 2026
oursДолго искал, кому это отдать, и вот нашёл. Повод для визита: намерзает лёд. Никита М объяснил причину так, что понял даже я. Сказали 32 500, я согласился без торга. Диагностику сделали бесплатно, хотя я был готов платить. В списке работ — уплотнитель. Рекомендую. Проверили при мне, показали, что всё держит
Мадина Т.Order No. TS-7219 · 28 November 2024
oursХотел сначала вызвать мастера на дом, потом передумал. Нужен был ремонт холодильника — обратился сюда. С чем пришёл: шумит. Сказали 27 000, а потом ещё и скидку сделали. Приехал вечером, мастер ещё был на месте. Заодно поменяли: термостат. В помещении тесновато, но это мелочи. Внешне как новый, если не считать мелкой царапины!!
Индира П.Order No. ZK-1617 · 20 September 2024
oursХотел сначала вызвать мастера на дом, потом передумал. Техсервис на Абая, если не ошибаюсь, — вот туда и поехал. Проверили на всех режимах, всё чётко!!
Лилия В.Order No. TS-4770 · 30 May 2024
oursРаботаю допоздна, поэтому нужен был сервис с нормальным графиком. Основная жалоба — намерзает лёд. Проверили при мне, показали, что всё держит.
Аружан К.Order No. ZK-2416 · 24 February 2023
oursДо этого обращался в другой сервис, там только развели руками. Проблема — не морозит. Проверили при мне, показали, что всё держит.
Данияр С.Order No. TS-2205-673 · 5 April 2022
oursДруг посоветовал, у него похожая история была. С чем пришёл: не морозит. Проверили при мне, показали, что всё держит.
Алексей Г.Order No. TS-4782 · 30 August 2021
oursБыло подозрение, что дело в плате, хотелось услышать второе мнение. Приехал из командировки, а дома — шумит. В списке работ — уплотнитель. Проверил дома — всё на месте, ничего не забыли
Татьяна Б.Order No. ZK-2020/765 · 2 October 2020
oursЖалоба простая: течёт. Отдельно спосибо мастеру — Дильмурат С, терпения ему хватило. Проверили при мне, показали, что всё держит!!
Станислав К.Order No. TS-3337 · 28 February 2017
oursПовод для визита: шумит. Дильмурат С всё объяснил и не пытался впарить лишнее. Уже полгода — ни одного сбоя.
Евгений М.Order No. TS-5582 · 15 February 2016
oursДолго откладывал ремонт, потом всё-таки собрался. Привёз на диагностику: холодильник. С чем пришёл: намерзает лёд. Ни копейки сверху, как и обещали. Разобрали, посмотрели: уплотнитель. Приняли без очереди, оформили за пять минут. Хороший сервис, побольше бы таких. Крутит ровно, без рывков
Didn’t find the answer? Message us on WhatsApp.
Ask a questionTech Service takes requests for Gorenje refrigerator repair in Almaty: a technician comes to your home within 60 minutes anywhere in the city, and diagnostics are free. We work directly, without middlemen or aggregators.
The most common issues are ice buildup, noise and clicking, no cooling while the light is on, errors on the display, and leaks. The technician will identify the specific component during free diagnostics; it depends on the model.
Yes, we repair NoFrost systems: we clean the drain, replace defrost sensors, the heating element and fan, and eliminate ice buildup. We provide a 1-year warranty on labor and parts; it depends on the model.
It depends on the fault: sometimes the inverter control board can be restored, but if the compressor itself is worn out, it is replaced. The technician will tell you what is needed in your case after free diagnostics.
Yes, we provide a 1-year warranty on the replacement of the compressor, thermostat and other components — both on labor and on parts. The technician confirms the terms during the in-home repair.
First, check that food isn't blocking the airflow and that the door closes tightly. If ice appears again, a defrost sensor or drain is likely faulty — the technician will determine the cause during free diagnostics.
Tech Service repairs Gorenje refrigerators in Almaty, both at your home and in our shop. Our technicians have 4 to 20 years of experience, arrive within 60 minutes anywhere in the city, provide free diagnostics, and give a 1-year warranty on labor and parts. The technician quotes the price after diagnostics.
Most Gorenje service calls start with one of a few typical symptoms. Let's break down which component is behind each one and why these failures are common for the brand.
Most often, when the light works but there's no cold, the culprit is the compressor, the start relay, or a refrigerant leak—we check these three components first. The technician measures pressure in the circuit, tests the motor windings for continuity, and checks the start protection: in Gorenje models with inverter and linear compressors, this part fails more often than the motor itself wears out. If there's a refrigerant leak, we check the circuit's tightness at joints and service ports—microcracks in the evaporator cause a gradual loss of cooling over several weeks. Diagnostics are free, and a technician arrives within 60 minutes anywhere in the city, so we identify the cause on site. When the motor hums but won't start, the issue is usually the start component, not the compressor itself—replacing it is simpler than installing a new motor, so it's important not to delay diagnostics. If your refrigerator has stopped cooling, it's best to entrust Gorenje refrigerator repair in Almaty to a technician who will check all components on site.
Clicking during startup points to the start protection part, while ice buildup in the NoFrost compartment indicates a faulty defrost heater, timer, or clogged drain. A hum with periodic clicks means the motor tries to start and is shut off by the protection: this is how a worn start component or a seizing compressor behaves. In NoFrost systems, ice builds up not because of cold but due to a defrost failure—the heater, timer, or sensor stops initiating the cycle, and the evaporator gets covered in frost. The drain hole gets clogged, condensate doesn't drain and freezes near the fan. We check the defrost circuit element by element and test each component separately to avoid replacing parts at random. If the cause isn't fixed, the fan starts hitting the ice, and cooling is lost throughout the compartment.
Water under the drawers is almost always a clogged drain hole, and a warm refrigerator compartment while the freezer works is a sign of a faulty thermostat or temperature sensor. Condensate flows down the groove into the drain, and when the passage is clogged with crumbs and slime, moisture accumulates at the bottom of the refrigerator compartment and leaks under the drawers. A warm top with a freezing freezer means the thermostat isn't signaling the motor to start, or the sensor is sending incorrect readings to the control board. In our experience, cleaning the drain often solves the problem without replacing parts. But if water appears again, it's worth checking the entire condensate drain tube—it may be displaced or cracked at the outlet, and without replacing it, the leak will return.
The Gorenje self-diagnosis system displays a code when a component fails. Let's explain what typical codes mean and when the board needs replacement.
| Code | Meaning | Likely Component | What We Check |
|---|---|---|---|
| E1 | Refrigerator compartment sensor failure | Temperature sensor | Sensor circuit and connector |
| E2 | Freezer compartment sensor failure | Temperature sensor | Sensor resistance |
| E4 | Defrost error | Defrost heater, timer | Heater heating, timer |
| E6 | Communication error with board | Control board | Contacts and module |
| E9 | NoFrost fan failure | Fan | Rotation and winding |
We more often repair Gorenje control boards than replace them — this is possible when individual components are damaged rather than the entire board. In our practice, typical cases include burnt triacs, swollen capacitors in the power circuit, and broken traces after moisture exposure: such defects are fixed by soldering with circuit testing under load. Replacement is needed when the microcontroller itself is blown or the damage covers several connected components at once — then a new module is more predictable in operation. When restoring the board, we preserve the factory settings and calibration, while when replacing, we set the parameters anew for the specific model. A 1-year warranty applies to both the restored board and the new part. The decision depends on the nature of the damage: local intervention preserves settings and avoids waiting for a new part, but for extensive damage, replacement is more reliable.
After a power surge, Gorenje refrigerators most often have a failed control board or start-protection relay — we check both components and the power circuit. Diagnostics are free: the technician tests the power cord, noise filter, input fuse, and compressor windings to distinguish burnt electronics from mechanical motor seizure. A city visit takes up to 60 minutes, so the technician begins the inspection soon after the request. A surge often damages several elements at once — the varistor absorbs the impulse, but the fuse and board traces behind it may not withstand. Even if the refrigerator turns on but doesn't cool, the surge could have partially damaged the electronics, so after such an event, it's worth checking the entire circuit, not just the visible symptom.
We show what a specialist does at home step by step, and in which cases the work is moved to the service center — with compressor and board disassembly.
A Gorenje refrigerator is taken to the service center when work cannot be done at home — for complex compressor replacement or control board restoration. Such components require disassembling the housing, soldering, and testing under load, which cannot be reproduced in a kitchen. The technician decides on the format after diagnostics: if the part can be replaced on-site, the unit is not transported. Avoiding transportation reduces the risk of damage during loading and reinstallation. In my opinion, the debate about whether to transport the refrigerator is unnecessary: first we inspect the component, then decide. Gorenje refrigerator repairs at the service center are performed with component testing under load. When choosing a service, ask who exactly picks up the equipment — a direct contractor handles transportation themselves, while an intermediary passes the unit to a third party, and responsibility becomes blurred.
The specialist comes for diagnostics and selects the needed part for Gorenje based on the refrigerator model — compatibility is checked before replacement. The compressor, thermostat, defrost sensor, and seal differ in fit and connector across series, so a universal part is not installed by eye. The exact refrigerator model speeds up selection: before calling, find the nameplate with the model designation — usually inside the refrigerator compartment or on the back wall. This saves time on approval and eliminates a repeat visit due to a mismatched part. In our experience, owners who photograph the nameplate in advance get a compatibility answer faster — the technician already knows the series and doesn't guess by the unit's appearance. If the nameplate is worn off, we clarify the model from the appliance documents or by characteristic series features.
Here's what the warranty covers, how free diagnostics works, and what goes into the price of the work — no hidden fees or pushy add-ons.
We provide a 1-year warranty on labor and a separate 1-year warranty on parts — this applies to both compressor replacement and thermostat replacement. In practice, the components that last longest are those where a quality part meets correct installation, so labor and parts are covered independently of each other. Compressor replacement carries the heaviest warranty burden: the unit runs under load, and its lifespan depends on proper refrigerant charging and checking the circuit for leaks. Thermostat replacement is simpler, but choosing the wrong model leads to false shutdowns a few weeks later. Parts and labor warranties are issued separately, so if you come back, it helps to remember which components were replaced — that makes it easier to confirm the case is covered.
Diagnostics are free: the technician identifies the cause of the breakdown and only then quotes the price for the work. We send our own employee to your address — not a courier or a call taker, but someone who disassembles the unit and fixes the fault themselves. The inspection starts with questions for the owner: when the symptom appeared, what changed in the appliance's behavior, whether there were any voltage spikes. Then the compressor, thermostat, sensors, and control board are checked to separate a mechanical failure from an electronic one. Around the city, the technician arrives within 60 minutes, so inspection and troubleshooting don't stretch over several visits. If the owner decides not to repair the refrigerator, the technician explains the cause of the breakdown — this helps you understand whether to proceed or replace the appliance.
The technician quotes the price after free diagnostics, and you can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies. The final amount depends on the nature of the fault and which component needs attention: compressor replacement, thermostat replacement, or control board work are tasks of different complexity, and each requires its own set of operations. We also consider whether a home visit is needed or the unit has to be disassembled at the service center: in the latter case, the scope of work is larger. The owner sees what the sum consists of before work begins and can decline if the proposed scope doesn't suit them. Since the price depends on the specific component and scope of work, quoting it in advance over the phone would be inaccurate — the exact amount only appears after inspection.
A direct contractor and an aggregator handle responsibility differently, and an active manufacturer's warranty changes how you should proceed. Let's look at how to tell one from the other and what to do in each case.
Tech Service works as a direct contractor: our own technician comes to your home, not a middleman who passes the request to a third party. Our Gorenje refrigerator service is handled by specialists with 4 to 20 years of experience, and they are the ones accountable for the result. With an aggregator, a single request involves various subcontractors with different qualifications: one comes today, another tomorrow, and you can't predict the quality of work in advance. As a result, obligations and responsibility get blurred between the platform and the contractor, and if the problem recurs, they argue among themselves. With a direct contractor, the technician and the obligations are one and the same — a 1-year warranty on labor and parts is backed by a specific organization. In my view, when choosing, you should immediately ask who exactly will come and who is responsible for the result: if the answer is vague, you're dealing with a middleman.
In most cases, a Gorenje inverter compressor is replaced rather than rebuilt — attempts to repair such units are unreliable and don't give lasting results. An inverter compressor adjusts its speed smoothly, without constant on-off cycling, so wear builds up gradually. The failure doesn't show up as a sudden breakdown but as a slow loss of cooling: the compartments seem to work, but food spoils faster, and ice builds up in the NoFrost system. When we see this pattern, our technicians check the windings and the start module to tell a compressor failure apart from an electronics fault. It's better to catch the gradual loss of cooling before the compartments fully thaw: that way the unit can be replaced without ruining food or needing a second visit, and the right part is matched to the specific model and compartment volume.
While the manufacturer's warranty is active, you need to contact them; after it expires, servicing is done by whichever shop the owner chooses. The manufacturer accepts requests by serial number and sends the appliance to its own network, and until the warranty ends, any third-party work may void it. Once it's over, the appliance doesn't become unrepairable — in fact, that's when owners more often turn to an independent shop to avoid overpaying for whole-unit replacements. An independent shop, meanwhile, assesses the unit as a whole and offers options for individual parts, not just replacement of major assemblies. A practical tip: before you call, check the purchase date and the terms on the warranty card — if the warranty is still running, go to the manufacturer first, and plan independent service for after it ends, keeping all records of the work done.
Here's the key things a Gorenje refrigerator owner should keep in mind before calling a technician: from decoding symptoms and display codes to checking the person who'll do the work.
90brands
We work with every brand sold in Kazakhstan — from Samsung, LG and Atlant to Biryusa, Indesit, Stinol and rare imported makes. Can’t find yours in the list? Call anyway — a technician will come and take a look.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your refrigerator stops working, first check the outlet, the power cord, and the thermostat setting, and after defrosting let it stand for a while.
4 February 2026 · 12 minutes read
If your refrigerator isn't cooling but the light is on, the cause is usually one of the components in the cooling circuit: the compressor, thermostat…
10 December 2025 · 13 minutes read
If your dishwasher won't drain, the most common culprits are a clogged filter or drain hose; less often, it's the pump, impeller…
24 March 2026 · 12 minutes read
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
If your microwave isn't heating but the light and turntable still work, the problem is usually one of the high-voltage components — the magnetron, diode…
15 February 2026 · 12 minutes read












