Original
Motor by part number
- Matching
- by model or part number
- Compatibility
- exactly matches the factory assembly
- Delivery time
- depends on supplier availability
- Warranty
- 1 year on labor and parts
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 746 00 26Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
Free diagnostics, a technician at your door within 60 minutes anywhere in the city. We work on washing machine motors and drives.
Our own technicians4 to 20 years of experience




1 yearwarranty on labor and parts
60 minutestechnician arrival anywhere in the city
4 to 20 yearstechnician experience
The technician checks the windings, commutator and brushes, inspects the belt and pulley, and if needed replaces the brushes, bearings with a seal, or the whole motor. The price is quoted after free diagnostics, and there's a 1-year warranty on labor and parts.
01
Step 1a few minutes
The technician measures winding resistance, inspects the commutator and brushes, and checks that the shaft spins freely.
02
Step 2a few minutes
They inspect the belt, pulley and tension: a slipping belt can cause symptoms similar to a weak motor.
03
Step 3about half an hour
Brushes on commutator motors wear down; new ones are fitted to size and bedded to the commutator.
04
Step 4one to two hours
If there's a humming noise during the spin cycle, the tank bearings and seal are replaced, and the shaft is checked for wear.
05
Step 5about half an hour
If a winding is broken or the motor is seized, a new motor is installed, matched by model or part number.
6
The motor turns the drum. If the machine hums but the drum stays still, stops mid-cycle, or smells burnt, the motor, belt and brushes are checked. An error on the display points to the drive assembly, not the control board.
Drum spins in jerks
Spinning in one direction only or in pulses points to a faulty tachometer sensor or control module.
Stops during the spin cycle
Causes are an unbalanced load or overloading: the machine drops speed and won't go into the spin cycle.
Humming and vibration during spin
A growing hum, increasing vibration and drum play during the spin cycle mean the supports need checking.
Smell of burnt insulation
If there's a burnt smell, the detergent powder or laundry has darkened, stop washing and call a technician.
Drive error on the display
Write down the error code from the display before the technician arrives — it speeds up diagnostics.
Before calling a technician, unplug the machine and don't try to force the drum to turn.
Describe the symptomsThe part is matched by the machine model or part number; for Bosch, by the E-Nr on the rating plate inside the door. The price for the part is quoted after diagnostics.
Original
or
Aftermarket
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1–2 hourstime
from 3 000 ₸cost

BeforeAfterThe home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsExpert washing machine repair technician
experience8 yearsSenior washing machine repair technician
experience9 yearsWashing machine repair technician
We reply during working hours
A technician will arrive within 60 minutes anywhere in the city, and diagnostics are free. Labor and the part are covered by a 1-year warranty. You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies.

Warranty question? Call us
+7 (778) 746 00 267 898 reviews of repairs at TECH SERVICE in total
Богдан С.Order No. 69617 · 14 July 2026
oursСимптом был очевидный: не отжимает. В techservice попал случайно — и остался. Сказать, что доволен — ничего не сказать.
Малик Т.Order No. ZK-2025/600 · 2 July 2025
oursБыло важно, чтобы сделали до выходных — гости, то-сё. Жалоба простая: не отжимает. Работает как раньше, придирок нет
Ксения И.Order No. 819682 · 12 May 2025
oursСмотрел, у кого есть запчасти на такую модель. Позвонили заранее, предупредили, что задержиться на полчаса. Пользуюсь ежедневно, вопросов нет!!
Светлана Д.Order No. TS-2101-184 · 4 November 2021
oursДосымның кеңесімен келдім, өкінбедім. Жұмыс барысын көрсетіп отырды, жасырған жоқ. Жөндеуге кепілдік бар, сол сенімді.
Кристина Л.Order No. TS-9241 · 13 January 2021
oursИскал мастерскую поближе к дому, чтобы не мотаться с техникой через полгорода. Отдал мастеру: стирально-сушильная машина. Симптом был очевидный: не сушит. Ораз взялся за то, от чего другие отказались. Сначала сказали одно, потом уточнили, но в итоге всё совпало. Оплатил картой, чек дали. В списке работ — тэн. Не пожалел ни разу. Ребёнок уже проверил на прочность, держится
Владимир Н.Order No. ZK-5322 · 16 October 2019
oursЖалоба простая: течёт. Работает как раньше, придирок нет. Сделали и забыл про проблему.
Сауле Н.Order No. TS-1904-298 · 19 June 2019
oursЦена имела значение, но и гарантия тоже. Скажу прямо: ожидал худшего. Больше всего напрягало: ошибка на дисплее. Шум пропал, работает мягко
Алмас Д.Order No. ZK-2018/189 · 30 September 2018
oursСимптом был очевидный: не сушит. Рустем Т перезвонил, когда всё было готово. Гудит ровно, не греется, всё как надо.
Виктор Ф.Order No. TS-6901 · 15 June 2017
oursПробовал найти мастера в своём районе, но все были заняты. Пользуюсь ежедневно, вопросов нет.
Мирас С.Order No. TS-6042 · 15 January 2017
oursОтдельно спосибо мастеру — Рустем Т, терпения ему хватило. Запчасть была в наличии, доплачивать не пришлось. Проверили при мне, показали, что всё держит
Didn’t find the answer? Message us on WhatsApp.
Ask a questionMost often, an old machine is turned into a pressure washer, a homemade machine tool, or a compressor. But if the motor still works, it's wiser to have a technician look at it first — the motor may be repairable and the machine can keep running.
If the motor can be restored and the tub and electronics are intact, motor repair will cost less than a new machine. When the whole unit is worn out, replacing the appliance may be the smarter choice — a technician will assess this during free diagnostics.
Motor durability depends less on the brand and more on the motor type and operating conditions: brushed models wear out their brushes over time, while inverter motors have a different weak point. A technician determines the cause after diagnostics, not by the brand name.
Beko motors are considered fairly reliable, but a lot depends on the model and operating conditions: brushed motors wear out their brushes over time, while inverter ones last longer. With proper care, the motor runs for years, and if it breaks down, it can be repaired or replaced.
It depends on the fault: brushed motors often just need new brushes, while inverter motors are harder to repair and it's not always possible. After disassembly, the technician will tell you what's cheaper — restoring the unit or installing another motor.
Yes, you shouldn't keep washing: sparks and the smell of burnt insulation indicate a motor or wiring fault, and that's a risk of short circuit. Unplug the machine and call a technician — diagnostics in Almaty are free.
Tech Service repairs washing machine motors in Almaty at the customer's home. A technician arrives within 60 minutes anywhere in the city, diagnostics are free, and there is a 1-year warranty on labor and parts. We first identify the motor type and the cause, then give you the price and agree on repair or replacement.
Humming and a stopped spin cycle don't always mean the motor. Similar symptoms can come from an unbalanced drum, a clogged drain, or a worn drive belt. Here's how a technician tells a motor failure from other causes.
In our experience, humming during the spin cycle is more often caused by an unbalanced drum, a clogged drain, or a drive belt, and only after checking those does the technician look at the motor. Clothes bunch up, the machine won't spin up to 800–1600 rpm, and it hums and stops — that's how an imbalance behaves. If the drum turns hard and you hear squeaking, the drum bearing is checked. A clogged filter at the bottom front behind the service flap or debris in the drain pump impeller can also cause a stop mid-cycle. A slipped or stretched drive belt explains why the tub doesn't rotate even though the motor hums. If the drum still won't turn after replacing the belt, the cause is already in the motor or its wiring, and then diagnostics focus on the electrical part.
Sparks and a burnt smell from the motor are a sign of worn brushes in a commutator motor or damaged winding, and you shouldn't keep washing. Unplug the machine, drain the water through the emergency drain hose behind the service flap at the bottom front, and put a towel down — the water may be hot. Inverter motors like Bosch EcoSilence Drive and LG Direct Drive have no brushes, so sparking there points to wiring, contacts, or the control board, not the brush assembly. With this symptom, the technician first checks the brushes and commutator rather than replacing the whole motor, because worn brushes are the most common cause in commutator motors. The part is matched by part number or model code; for Bosch, by the E-Nr on the rating plate inside the door.
Repair and replacement are not the same thing. Below we explain what the choice depends on and why motor repair isn't right for every machine.
We first assess which component has failed, and in commutator motors it's often enough to replace the brushes rather than the whole motor. In our practice, restoring a washing machine motor starts with disassembling the unit: the technician inspects the brushes, commutator, and winding, and checks whether the shaft turns freely. We perform washing machine motor repairs in Almaty after such disassembly and inspection. Motor replacement is needed when wear affects the winding or commutator, not just the brushes — such a motor can't be restored on-site. Our diagnostics are free, a technician arrives within 60 minutes anywhere in the city, and we provide a 1-year warranty on labor and parts. Our experience ranges from 4 to 20 years across different brands. The decision to replace is based specifically on the condition of the winding and commutator, so the technician first disassembles and checks the motor rather than replacing the unit blindly. Ask the technician what the disassembly revealed — that's the basis for choosing between repair and a new motor.
| Motor type | What is repaired | What is replaced |
|---|---|---|
| Commutator | brushes, contacts | motor when winding is worn |
| Inverter | wiring, contacts | the whole unit |
| Induction | wiring, contacts | motor when winding is damaged |
The drive type determines what work is possible when it breaks and which parts are even sought. We cover the three types and brand-specific features of Bosch and LG.
A brushed motor has carbon brushes that wear out over time, while an inverter motor doesn't have them, so that kind of wear doesn't apply. The brush assembly transfers rotation through a belt, sparks on worn graphite inserts, and is found in budget models from Indesit, Hotpoint, and some Samsung machines. An inverter drive is controlled by electronics, smoothly changes drum speed, and has no rubbing parts — its weak point shifts to the bearing and control board. Bosch EcoSilence Drive and LG Direct Drive have no graphite, so if you hear a hum or the machine stops, look for the cause in the wiring, bearing, or electronics, not in a wear part. In practice, this changes diagnostics: the technician first listens to the type of noise and checks the board rather than taking the assembly apart hoping to replace something.
We only replace the drum bearing when the tub is serviceable, and we select the motor by part number or model code, including for machines that are no longer in production. When the tub is sealed, the bearing isn't replaced separately — the work follows a different scenario, and it's important to say this before disassembly. To choose a part, we match the part number and model code: on Bosch both are on the rating plate inside the door (E-Nr), and they make it easier to find the right assembly than the series name. Older Maxx, Logixx, and Classixx lines and the current Serie 2, 4, 6, and 8 differ in parts, so the series name alone guarantees nothing. Our technician confirms the E-Nr before the visit, so the right part comes along instead of being searched for after the first disassembly.
The combination on the display is a hint, not a verdict. We show how a specialist checks it against the model and why flashing indicators don't always mean a motor failure.
On older Bosch and Siemens series (Maxx, Classixx, Logixx, Avantixx), the F21 code points to the motor, but the meaning depends on the model, and the specialist checks it against the table for your machine. The same F21 on another series may describe a different fault, so a single combination doesn't condemn the motor. On Bosch and Siemens, the heating element is at the front and the pump at the bottom, so access to components during testing differs. Drain codes from other brands are their own: Samsung 5E (SE, E2), Electrolux E20, Indesit and Hotpoint F05 — they can't be mixed with Bosch F-codes. On models without a display, indicators show the signal, so when lights flash, it's more important to give the series and model than to guess the code.
Our specialist first checks whether the pump impeller turns freely and whether there's a blockage, and only then moves on to the motor and belt. The drain pump doesn't run while the machine fills, so it's tested separately from the fill cycle. A multimeter won't show a jammed pump — it's checked by hand by turning the impeller, not by continuity testing. The causes of pump failures are debris (coins, lint, small objects) and a clogged filter, which is at the bottom front behind the service flap. If the drum doesn't spin after a belt replacement, our technician checks belt tension and the pulley condition, then tests the motor winding. We arrive within 60 minutes across the city, diagnostics are free, and we give a 1-year warranty on labor and parts.
We explain how a technician call works: what happens during an at-home visit, when the job moves to the service center, and exactly what the warranty covers after a motor replacement.
We come to your home anywhere in the city within 60 minutes, and if it's more convenient to do everything at the service center, the technician will arrange that with you on the spot. Diagnostics are free: the specialist opens the machine, checks the motor, belt, brushes of the commutator motor, and the control board to pinpoint the faulty unit. Once the cause is clear, they explain the scope of work and offer two options — fix it at home or take the machine to the service center, where there are proper conditions for disassembling the drum. The technician gives you the price after the free diagnostics, when it's already clear which unit has failed and what work is needed. In my view, on-site work covers most motor cases, while machines with a non-separable drum and bearings are brought to the service center. You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies — cash, card, or transfer.
Our 1-year warranty covers both labor and parts, including a replaced motor. A few months after the work, you're not left alone with a breakdown: if the motor starts humming again, jerking during the spin cycle, or the machine stops turning the drum, a repeat visit will be handled under the same warranty. The technician who worked on your machine remembers which unit was replaced and which belt or brushes were installed — that data makes it easier to match a new symptom to the previous work. If the motor again behaves the way it shouldn't, the warranty covers both the repeat labor and the part itself. For older series like Maxx or Classixx, this is especially valuable: finding the right motor for them is harder, and repeat failures are not uncommon.
To sum up: the key points for a machine owner who suspects the motor — no unnecessary details, just the essentials.
If you ask, the technician will check other parts during the same visit.
Refrigerator Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
Washing machine error codes are self-diagnostic codes that point to a specific component: drain, water fill, heating, motor, or door lock.
29 January 2026 · 13 minutes read
If your washing machine won't spin, it's usually an unbalanced load, a clogged drain filter or hose, and less often the pump, belt…
19 January 2026 · 12 minutes read
If your washing machine isn't heating water, the heating element or temperature sensor is usually to blame, less often the control board or wiring.
25 December 2025 · 12 minutes read
If your washing machine won't turn on, first check the outlet, extension cord, and the circuit breaker in your panel, then the plug and power cord.
24 November 2025 · 13 minutes read