experience9 yearsRuslan Ts.
Washing machine and refrigerator repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 746 00 26Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Diagnostics are free.
Our own technicians4 to 20 years of experience




Repair prices
If your Grand refrigerator stops holding temperature, check whether the settings have shifted and the door closes tightly. The technician will identify any other causes on site.
refrigerant leak, compressor failure
from10 500 ₸
no power, burnt start relay
from7 500 ₸
clogged drain, misaligned tray
from5 000 ₸
compressor touching the cabinet, worn mounts
from24 500 ₸
loose door seal, faulty defrost sensor
from6 000 ₸
faulty sensor, control board failure
from6 000 ₸
settings off, stuck thermostat
from9 500 ₸
clogged drain, tilted cabinet
from5 000 ₸
The table lists the 'from' price for labor and the time required; the technician confirms the final amount before any repair begins.
1 visittime
from 9,500 ₸cost

BeforeAfter5 steps

Five steps from request to checking the result.
Describe the symptom and your Grand refrigerator model so the technician brings the right tools.
A technician arrives within 60 minutes anywhere in the city, including remote areas of Almaty.
The technician agrees the scope of work with you before starting the repair.
The technician agrees any replacement parts with you before installing them.
The technician demonstrates the unit working after reassembly, and you accept the result.
The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsField refrigerator repair technician
experience12 yearsGeneral household appliance repair technician
experience8 yearsExpert washing machine repair technician
We reply during working hours
Describe the symptom and your Grand refrigerator model — the technician will bring the right tools and prepare for diagnostics. 1-year warranty on labor and parts.

Warranty question? Call us
+7 (778) 746 00 267 898 reviews of repairs at TECH SERVICE in total
Ксения И.Order No. TS-2612-282 · 29 August 2026
oursХотел сначала вызвать мастера на дом, потом передумал. Первое, что заметил: намерзает лёд. Никита М взялся за то, от чего другие отказались. Гудит ровно, не греется, всё как надо
Мирас С.Order No. TS-2641 · 13 July 2026
oursПроблема — течёт. Отдельно спосибо мастеру — Никита М, терпения ему хватило. Сделали и забыл про проблему.
Юлия А.Order No. TS-5126 · 17 April 2023
oursПробовал найти мастера в своём районе, но все были заняты. Утром столкнулся с тем, что течёт. Позвонил, описал проблему, сказали привозить — посмотрят в тот же день. Вышло дешевле нового, что логично. Из деталей — компрессор. Хороший сервис, побольше бы таких. Работает как раньше, придирок нет.
Ерасыл Б.Order No. 954197 · 13 August 2021
oursТехника на гарантии уже не была, так что выбор был свободный. Честно говоря, доверяю больше тем, кто говорит по делу. Симптом был очевидный: течёт. Из деталей — термостат. Вышло 20 000 тенге, дешевле, чем я рассчитывал. Ответили быстро, не пришлось ждать на линии. Техсервис на Абая, если не ошибаюсь, — вот туда и поехал. Уже полгода — ни одного сбоя.
Азамат Е.Order No. 20528 · 1 May 2021
oursДруг посоветовал, у него похожая история была. Первое, что заметил: течёт. Починили и дали гарантию на месяц.
Бекзат Т.Order No. ZK-2020/226 · 1 August 2020
oursСмотрел, у кого есть запчасти на такую модель. Обидно было, техника не старая совсем. С чем пришёл: намерзает лёд. Никита М возился с этим дольше, чем планировал, но довёл до конца. Сделали и забыл про проблему.
Вероника П.Order No. 46065 · 7 August 2018
oursНужен был счёт и чек, у нас техника на балансе организации. Повод для визита: течёт. Проверил дома — всё на месте, ничего не забыли
Павел Ш.Order No. 2018-7272 · 9 January 2018
oursСимптом был очевидный: шумит. Дильмурат С честно сказал, что менять, а что ещё походит. Шум пропал, работает мягко.
Куаныш Б.Order No. 2017-1993 · 27 June 2017
oursНужен был счёт и чек, у нас техника на балансе организации. Диагностика холодильника — с этого всё началось. Повод для визита: шумит. Поставили новую деталь: компрессор. Мастер посмотрел, сказал, что возьмёться, и взялся. С тех пор ни разу не подвёл.
Ольга М.Order No. TS-1608-592 · 23 May 2016
oursТехника на гарантии уже не была, так что выбор был свободный. Позвонил узнать про ремонт холодильника. Жалоба простая: течёт. Ответили быстро, не пришлось ждать на линии. Деталь на замену — уплотнитель. Даже с учётом запчасти вышло гуманно. Цену назвали не сразу, пришлось уточнять. Если что — обращусь снова. Второй месяц — полёт нормальный.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionIf the light works but there's no cold, the compressor has usually failed, there's a refrigerant leak, or the thermostat is broken. The technician will pinpoint the exact cause during free diagnostics after inspecting the components.
When the thermostat fails, the compressor may not shut off or may not start at all, and there's no cooling. If the compressor doesn't start and you hear a click, it could indicate a compressor fault. The technician will make an accurate diagnosis after testing.
Ice buildup in a No Frost system is caused by a faulty defrost sensor, heating element, or a clogged drain, and less often by a door that doesn't seal tightly. It depends on the Grand model, so the cause is determined after inspecting the defrost components.
Most Grand breakdowns are fixed on-site by a Tech Service technician: replacing the thermostat, relay, fan, or repairing the control board. The appliance is only taken to the service center if a complex repair of a component that can't be accessed on-site is needed.
Before calling a technician, it's worth checking that the door closes tightly, there's no ice buildup, and the compressor starts when you listen. You shouldn't touch the electricals or refrigerant circuit; the technician will determine the rest during free diagnostics.
A repeat failure may mean the cause wasn't fully found: for example, a micro-leak of refrigerant remains or the control board is faulty. Under the 1-year warranty, a Tech Service technician will run diagnostics again and fix the cause.
Tech Service repairs Grand refrigerators in Almaty: our technician comes to your home within 60 minutes anywhere in the city, or the appliance is fixed at our service center. Diagnostics are free, there's a 1-year warranty on labor and parts, and our technicians have 4 to 20 years of experience. We give you the price after diagnostics.
A Grand refrigerator not cooling but the light is on — it's not always the compressor. Let's break down how to use the symptom and the error code on the display to figure out which part has failed.
We start diagnostics by checking the compressor and the start relay: if the unit is humming but there's no cold, it's most often a refrigerant leak or a clogged capillary tube. A running compressor creates the illusion of normal operation — the fan and the light inside the compartment keep working too, so the owner doesn't immediately notice that the evaporator has stopped cooling. A clogged capillary tube gives the same symptom: the motor hums, the condenser on the back grille stays cold or only partially warm. When refrigerant escapes, the circuit loses pressure, and the compressor runs without load, barely heating up. If it starts and then stops with a click after a minute, that's a sign the protection has tripped — don't take the unit apart yourself; the relay and windings are checked with a meter. The technician measures winding resistance and current draw: a discrepancy with the spec values immediately shows whether the part is good or not.
The error code on a Grand display is shown by the control board when a sensor or component fails, and decoding the code immediately narrows down the search — we check it against the model's table on site. On models with electronic control, the board polls the temperature sensors in the fridge and freezer compartments, the evaporator sensor, and the defrost sensor, and when a signal goes out of the acceptable range, it shows the corresponding code on the display. The same code on different Grand series can mean different things, so we take the decoding from the service table for the specific model, not from general memory. The code on the display doesn't always point to the sensor itself: it often signals a consequence — for example, a faulty defrost heater, which makes the sensor read the wrong temperature. Before replacing the sensor, the technician checks the defrost circuit and the heater's resistance; otherwise, the replacement won't fix the cause.
We distinguish a refrigerant leak from compressor wear by current and pressure in the circuit: when refrigerant escapes, the motor runs without load and barely heats up, while with wear it hums louder and overheats. Measuring current draw shows how the compressor is running: a healthy unit keeps current within the spec value, with a leak it drops, and with mechanical wear it rises. The pressure in the cooling circuit on the suction and discharge sides confirms the picture: a low reading on a running unit indicates a lack of refrigerant, not a compressor failure. The condenser on the back grille with a leak stays evenly warm only at the inlet, and cold beyond that. If cold returns after recharging with refrigerant but disappears again after a few days, there's still an open microcrack in the circuit — it's found with a leak detector, not by recharging again. In Almaty, a technician arrives within 60 minutes, and diagnostics are free.
Like any brand, Grand has its typical symptom-to-component links. Below we cover the most frequent owner complaints and show what the technician actually checks.
Humming and clicking in Grand refrigerators are most often caused by the start-protection relay and the evaporator fan: the first clicks when the compressor tries to start, while the second hums when its bearing wears out in No Frost systems. The start-protection part sits in the motor winding circuit and cuts power when the starting current exceeds the norm, so a series of clicks without starting points either to it or to a seized compressor. In No Frost systems, a separate fan handles air circulation: over time its bearing dries out, and the hum grows along with frost buildup on the evaporator. Our technician listens to both components separately on site — the start element is disconnected from the circuit and a direct start is tested. If the hum appeared right after defrosting, check that the cabinet stands level and the rear grille isn't touching the wall — condenser resonance can sound like a motor failure.
Ice on the rear wall of a Grand in No Frost models indicates a defrost system failure: we check the heating element, timer, and sensor, and in drip models — the door seal and defrost mode. In No Frost systems, moisture on the evaporator should drain away during the defrost cycle: if the heater burns out or the timer fails to switch modes, frost grows and blocks the air channels, and cold stops reaching the compartments. The sensor may then show the wrong temperature, and the cycle starts at the wrong time. In drip models, frost often appears because the door doesn't seal tightly: warm air gets inside, moisture settles on the wall and freezes — the seal is replaced if it has hardened or torn.
An inverter compressor in a Grand is diagnosed by the control board and windings, not just by startup: it changes speed smoothly, so "the motor isn't audible" doesn't mean it's broken. A conventional motor runs at constant speed and starts through the start relay, so its condition shows in the current and the pattern of clicks. In an inverter model, the board converts power and sets the rotation frequency, so the technician first reads the module parameters and checks winding resistance, and only then draws a conclusion about the motor itself. In dual-compressor models, the units work independently, and one failure doesn't mean the other is fine — we check both circuits. An inverter compressor is more often repairable electronically than mechanically: if the winding burns out, it's replaced as a whole, while a control board or sensor failure is fixed by replacing the module.
Grand refrigerator repair in Almaty follows one procedure: request, free diagnostics, approval of work, the repair itself, and warranty. Let's walk through each step — from the first call to the moment the appliance freezes again.
During free diagnostics, we check the compressor and start-protection relay, thermostat and temperature sensor, the circuit for refrigerant leaks, and decode error codes from the Grand display. The technician measures starting current, tests the windings, compares sensor readings with the manufacturer's table, and inspects the evaporator for frost. For No Frost, they separately listen to the evaporator fan and check the defrost cycle. Diagnostics aren't about guessing the fault by eye — they're to name the exact cause and scope of work before disassembly, so you agree to the work already knowing which parts are being replaced and why. In our experience, half of the disputed cases are resolved at this stage: a suspected compressor turns out to be a refrigerant leak, and it's the joint that gets fixed, not the unit.
| Task | Where we do it | What we check |
|---|---|---|
| Start relay replacement | On-site | Compressor windings, starting current |
| Thermostat and temperature sensor replacement | On-site | Compartment temperature, cut-off cycle |
| No Frost fan replacement | On-site | Evaporator airflow, frost buildup |
| Door seal replacement | On-site | Door fit, gap |
| Defrost heater and timer replacement | On-site | Defrost cycle, drainage |
| Control board repair | On-site or in-shop | Error codes, sensors |
| Compressor replacement | In-shop | Windings, circuit pressure |
| Leak detection and refrigerant recharge | In-shop | Circuit tightness, capillary tube |
We provide a 1-year warranty on labor and parts: if your Grand refrigerator stops cooling for the same reason after the repair, the technician comes back. The warranty covers the replaced component and the work itself, so you don't pay for diagnostics again if the problem returns — the technician identifies the cause and fixes it under warranty. In our experience, the most common repeat visit is for the door seal: it wears out faster than other parts, and if installed incorrectly, the gap comes back within a few weeks. That's why after replacing the seal we check the fit around the entire perimeter and ask the owner not to remove the door from its hinges in the first few days. A warranty case is registered for the same part listed in the order — keep the note about the replaced component.
Not every Grand "breakdown" requires a technician visit — the owner can check some causes in a couple of minutes, and we'll honestly tell you when the call can wait.
The No Frost system in Grand refrigerators doesn't require manual defrosting: the evaporator defrosts automatically on a timer, and the owner only needs to clean the compartments and keep the drain hole clear. Moisture from food and air settles on the evaporator, the defrost heater periodically melts it, and the water drains through the drain tube into the tray above the compressor. A clogged drain is the most common cause of a puddle under the vegetable drawers even when cooling works perfectly. If ice does appear in a No Frost model, it's not because you "forgot to defrost" but due to a fault in the defrost heater, timer, or sensor — manual defrosting will only give a temporary effect. Check the drain hole every time you clean the compartments: the thin tube clogs with crumbs and mold faster than you think, and you can clear it with soft wire without disassembling the unit.
When it comes to how much a Grand refrigerator repair costs, the number matters less than who does it and how — let's look at the types of work and how to choose a technician.
We come to your home within 60 minutes anywhere in the city and fix on the spot any issues that don't require dismantling the refrigerant circuit. Complex cases involving compressor replacement are handled at our service center. During a home visit, the technician checks thermostats, sensors, start relays, wiring, fan and door seals — these components can be replaced without moving the appliance, right in your kitchen. Compressor replacement, circuit brazing and evacuation require a workshop: such operations can't be done cleanly and safely on-site, and after brazing the system must be purged and charged with refrigerant by weight. Our diagnostics are free in both formats, so the decision is made after inspection, not over the phone. When choosing the format, focus on the symptom: if the fridge won't start or clicks, a home visit is usually enough; if it's not cooling while the motor runs, there's likely a refrigerant leak and a service center is needed. We repair Grand refrigerators in Almaty in both formats, so you can choose the right one after inspection.
When choosing a service for Grand, check whether it works as a direct contractor with its own technicians, provides a warranty on labor and parts, and performs diagnostics before agreeing on repairs. Our Grand refrigerator service in Almaty is handled by technicians with 4 to 20 years of experience, and a 1-year warranty covers both labor and installed parts. A direct contractor means a staff technician arrives at your address, not a subcontractor from an intermediary platform: such a specialist is personally responsible for the result and doesn't pass it on to a third party. Ask which Grand series they've worked with: inverter and dual-compressor lines are designed differently, with different start automation, control boards and defrost algorithms. A service that takes on everything often doesn't know these nuances — check whether the technician has dealt with your specific series and which components they've replaced in it.
Grand symptoms follow a simple logic: what the display shows, which component is responsible, where the work is done, and what you get in the end.
90brands
We work with every brand sold in Kazakhstan — from Samsung, LG and Atlant to Biryusa, Indesit, Stinol and rare imported makes. Can’t find yours in the list? Call anyway — a technician will come and take a look.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your refrigerator stops working, first check the outlet, the power cord, and the thermostat setting, and after defrosting let it stand for a while.
4 February 2026 · 12 minutes read
If your refrigerator isn't cooling but the light is on, the cause is usually one of the components in the cooling circuit: the compressor, thermostat…
10 December 2025 · 13 minutes read
If your dishwasher won't drain, the most common culprits are a clogged filter or drain hose; less often, it's the pump, impeller…
24 March 2026 · 12 minutes read
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
If your microwave isn't heating but the light and turntable still work, the problem is usually one of the high-voltage components — the magnetron, diode…
15 February 2026 · 12 minutes read












