experience9 yearsRuslan Ts.
Washing machine and refrigerator repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 746 00 26Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician will come to your home and find the cause of the problem. Diagnostics are free, and the technician arrives within 60 minutes anywhere in the city.
Our own technicians4 to 20 years of experience




Repair prices
Below are typical symptoms, likely causes, and service costs. The technician will determine the exact cause during a free diagnostic.
refrigerant leak, clogged capillary tube
from10 500 ₸
defrost failure, faulty sensor
from6 000 ₸
clogged drain, misaligned tray
from5 000 ₸
refrigerant leak, clogged capillary tube
from12 000 ₸
faulty start relay, burnt control board
from7 500 ₸
compressor wear, loose mounting
from24 500 ₸
dirty compartments, clogged drain
from5 000 ₸
sensor failure, faulty board
from6 000 ₸
The table shows labor costs "from," excluding parts and fridge repair turnaround; the technician confirms the final total before any work begins.
1 visittime
from 6 500 ₸cost

BeforeAfter5 steps

Five steps from request to checking the work after repair.
Describe the symptom and refrigerator model so the technician brings the right tools.
The technician arrives within 60 minutes anywhere in the city, coming to the client's home.
The technician agrees on the scope of work and list of parts to replace before starting repairs.
The technician performs the agreed work and checks the operation of the refrigerator components.
Check that it cools properly, with no ice buildup or unusual noise after turning it on.
The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsField refrigerator repair technician
experience12 yearsGeneral household appliance repair technician
experience8 yearsExpert washing machine repair technician
We reply during working hours
Describe the symptom and refrigerator model in your request — the technician will prepare for the visit and bring the necessary tools. We'll agree on a convenient visit time upon confirmation.

Warranty question? Call us
+7 (778) 746 00 267 898 reviews of repairs at TECH SERVICE in total
Ксения И.Order No. TS-2612-282 · 29 August 2026
oursХотел сначала вызвать мастера на дом, потом передумал. Первое, что заметил: намерзает лёд. Никита М взялся за то, от чего другие отказались. Гудит ровно, не греется, всё как надо
Мирас С.Order No. TS-2641 · 13 July 2026
oursПроблема — течёт. Отдельно спосибо мастеру — Никита М, терпения ему хватило. Сделали и забыл про проблему.
Асель Ж.Order No. 2026-4630 · 5 February 2026
oursДолго искал, кому это отдать, и вот нашёл. Повод для визита: намерзает лёд. Никита М объяснил причину так, что понял даже я. Сказали 32 500, я согласился без торга. Диагностику сделали бесплатно, хотя я был готов платить. В списке работ — уплотнитель. Рекомендую. Проверили при мне, показали, что всё держит
Алексей Г.Order No. TS-2501-114 · 4 August 2025
oursРаботаю допоздна, поэтому нужен был сервис с нормальным графиком. По деньгам вышло адекватно, в другом месте просили больше. Уже полгода — ни одного сбоя)
Мадина Т.Order No. TS-7219 · 28 November 2024
oursХотел сначала вызвать мастера на дом, потом передумал. Нужен был ремонт холодильника — обратился сюда. С чем пришёл: шумит. Сказали 27 000, а потом ещё и скидку сделали. Приехал вечером, мастер ещё был на месте. Заодно поменяли: термостат. В помещении тесновато, но это мелочи. Внешне как новый, если не считать мелкой царапины!!
Индира П.Order No. ZK-1617 · 20 September 2024
oursХотел сначала вызвать мастера на дом, потом передумал. Техсервис на Абая, если не ошибаюсь, — вот туда и поехал. Проверили на всех режимах, всё чётко!!
Лилия В.Order No. TS-4770 · 30 May 2024
oursРаботаю допоздна, поэтому нужен был сервис с нормальным графиком. Основная жалоба — намерзает лёд. Проверили при мне, показали, что всё держит.
Юлия А.Order No. TS-5126 · 17 April 2023
oursПробовал найти мастера в своём районе, но все были заняты. Утром столкнулся с тем, что течёт. Позвонил, описал проблему, сказали привозить — посмотрят в тот же день. Вышло дешевле нового, что логично. Из деталей — компрессор. Хороший сервис, побольше бы таких. Работает как раньше, придирок нет.
Аружан К.Order No. ZK-2416 · 24 February 2023
oursДо этого обращался в другой сервис, там только развели руками. Проблема — не морозит. Проверили при мне, показали, что всё держит.
Данияр С.Order No. TS-2205-673 · 5 April 2022
oursДруг посоветовал, у него похожая история была. С чем пришёл: не морозит. Проверили при мне, показали, что всё держит.
Алексей Г.Order No. TS-4782 · 30 August 2021
oursБыло подозрение, что дело в плате, хотелось услышать второе мнение. Приехал из командировки, а дома — шумит. В списке работ — уплотнитель. Проверил дома — всё на месте, ничего не забыли
Ерасыл Б.Order No. 954197 · 13 August 2021
oursТехника на гарантии уже не была, так что выбор был свободный. Честно говоря, доверяю больше тем, кто говорит по делу. Симптом был очевидный: течёт. Из деталей — термостат. Вышло 20 000 тенге, дешевле, чем я рассчитывал. Ответили быстро, не пришлось ждать на линии. Техсервис на Абая, если не ошибаюсь, — вот туда и поехал. Уже полгода — ни одного сбоя.
Азамат Е.Order No. 20528 · 1 May 2021
oursДруг посоветовал, у него похожая история была. Первое, что заметил: течёт. Починили и дали гарантию на месяц.
Татьяна Б.Order No. ZK-2020/765 · 2 October 2020
oursЖалоба простая: течёт. Отдельно спосибо мастеру — Дильмурат С, терпения ему хватило. Проверили при мне, показали, что всё держит!!
Бекзат Т.Order No. ZK-2020/226 · 1 August 2020
oursСмотрел, у кого есть запчасти на такую модель. Обидно было, техника не старая совсем. С чем пришёл: намерзает лёд. Никита М возился с этим дольше, чем планировал, но довёл до конца. Сделали и забыл про проблему.
Сергей Р.Order No. 598321 · 25 April 2020
oursВыбирал по отзывам в 2ГИС, времени на эксперименты не было. До последнего откладывал, но пришлось признать: шумит. Могли бы взять больше, но взяли по-божески. Заявку приняли по телефону, перезвонили через десять минут. Деталь на замену — уплотнитель. Пять звёзд, не задумываясь. Ребёнок уже проверил на прочность, держится.
Светлана Д.Order No. ZK-2019/136 · 30 May 2019
oursБыло подозрение, что дело в плате, хотелось услышать второе мнение. Честно, уже готовился покупать новое, но обошлось. Проблема — шумит. Проверил дома — всё на месте, ничего не забыли.
Вероника П.Order No. 46065 · 7 August 2018
oursНужен был счёт и чек, у нас техника на балансе организации. Повод для визита: течёт. Проверил дома — всё на месте, ничего не забыли
Павел Ш.Order No. 2018-7272 · 9 January 2018
oursСимптом был очевидный: шумит. Дильмурат С честно сказал, что менять, а что ещё походит. Шум пропал, работает мягко.
Аяна Е.Order No. 25364 · 9 December 2017
oursОтдал мастеру: холодильник. Жалоба простая: шумит. Никита М объяснил причину так, что понял даже я. Смета совпала с итогом, что редкость. Поставили новую деталь: термостат. Мастер сразу сказал, что к чему, без размытых формулировок. Нагрев в норме, посторонних звуков нет.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionIt's usually the No Frost system: ice blocks the channel, so cold air doesn't reach the upper compartment. It depends on the model, but defrosting and having a technician check the defrost components often helps.
Most often the drain channel is clogged and condensation drips into the compartment. Less often the cause is the door seal or the defrost system; free diagnostics will pinpoint the exact cause.
The clicking means the start relay is trying to start the compressor, but it won't kick in. A technician will check the relay and the motor windings to determine what needs replacing.
The louder hum comes from either a worn compressor or loose mounts and vibrating pipes. A technician will listen to it running and eliminate the source of the noise; it depends on the model.
Yes, a technician comes to your home, decodes the code for your model and checks the relevant component. Many Bosch electronics faults are fixed right on site.
A technician fixes most faults on inverter models at home after diagnostics. The appliance is only taken to the service center for complex board or compressor repairs.
Tech Service is a direct provider of refrigerator repair in Almaty: our technician arrives at your home within 60 minutes anywhere in the city or picks up the appliance for service. Diagnostics are free, there's a 1-year warranty on labor and parts, and you can pay via Kaspi QR, Kaspi Red, bank card, cash or bank transfer for companies. The technician gives you the price after diagnostics.
A refrigerator breakdown almost always shows up as a specific symptom. Let's go over the most common ones we fix at home—what they mean and what the technician checks on site.
When the light is on but there's no cold, the compressor, a refrigerant leak, or the temperature sensor is usually to blame—the technician checks all three during the free diagnostics. The compressor pumps refrigerant through the circuit, the sensor sends the signal to start, and the refrigerant carries the cold into the compartments. If the freezer works but the fridge compartment doesn't, it often points to a leak or a clogged capillary rather than a broken motor in a two-compartment refrigerator. The technician performs home refrigerator repair only after confirming the cause: first checking the pressure in the circuit and the thermostat readings, then testing the compressor's starting current—this way, unnecessary part replacement is avoided. If the freezer works and the top compartment is warm, don't rush to agree to a motor replacement: first check the capillary and for leaks at the connections.
An inside leak is usually caused by a clogged drainage system, while an outside leak comes from a door seal or the unit being uneven; the technician checks the drainage and door alignment. Condensation runs down the groove into the drain hole on the back wall of the fridge compartment and evaporates in the tray above the compressor. When the drain is clogged with crumbs and ice, water ends up on the shelves and under the drawers. An outside leak appears if the door seal doesn't fit tightly and warm air gets inside—then there's more condensation than the drain can handle. Our technician checks both the drain itself and the door alignment with a level. Before calling a specialist, check if the drain hole on the back wall is clogged—sometimes the problem is solved by cleaning it without a technician visit.
Let's cover what the technician does right in your kitchen, when the appliance is taken to the service center, and how the free diagnostics before work goes.
| What we fix | At home | At the service center |
|---|---|---|
| Start relay | yes | — |
| Door seal | yes | — |
| Temperature sensors | yes | — |
| Electronic board adjustment | yes | — |
| Refrigerant recharge | yes | — |
| Compressor replacement | — | yes |
| Circuit soldering | — | yes |
A technician arrives within 60 minutes anywhere in the city, checks the components, identifies the cause and gives you the price after a free diagnostic — and only then starts work. First, they listen to how the appliance behaves: whether the motor hums, the relay clicks, the compartments stay cold. Then they inspect the seal, sensors, and control board, check the pressure in the circuit, and assess the start relay. Based on the inspection, they explain exactly what has failed and what work is needed. The price is given after the diagnostic, not over the phone — this protects you from a "guesswork diagnosis" when the cause is determined without seeing the appliance. In our experience, a significant share of "not cooling" calls are resolved by adjusting the board or replacing a sensor right in your kitchen. Fridge repair at home in Almaty is convenient because most faults are fixed on site. Diagnostics are free, so the inspection doesn't become a separate expense — you pay only for the work and the part.
We repair household fridges and freezers of various types and brands — from classic two-door models to inverter and No Frost units. A technician comes to your home or takes the appliance to the service center if the fault requires workshop conditions.
An inverter compressor smoothly adjusts cooling power, while a linear one works with a reciprocating piston stroke — we diagnose and restore both types. Inverter models are sensitive to voltage spikes — if the fridge stopped cooling after a power outage, the cause is often the control board, not the compressor itself. LG linear units fail differently: over time the piston loses its stroke, the compressor hums but doesn't pump refrigerant, and it sounds like it's working fine. We check the windings with a multimeter, test the board, and only then name the cause — we don't suggest replacing the compressor blindly. On inverter models, replacing the control board costs less than replacing the assembly, so we rule out the electronics first.
In a No Frost system, moisture is removed by the evaporator with a fan and a defrost heater. If they fail, ice builds up on the back wall or the fridge stops cooling. Ice on the back wall isn't always a breakdown: if the door was left open for a long time or the seal doesn't fit tightly, the system can't remove moisture fast enough. In two-compartment models with separate circuits, sometimes only the freezer works—then we check the damper and the compartment sensor. We inspect the door seal on every visit: a loose fit causes frost and extra load on the compressor. We service these units and two-compartment models on-site if the problem doesn't require replacing the entire evaporator—a technician arrives within 60 minutes anywhere in the city.
Let's break down how to tell a real freon leak from an upsell and when a compressor replacement is truly needed, not just maintenance for the sake of a bill.
Freon isn't consumed during operation—if it's low, there's a leak, and the technician first finds the leak, then recharges the circuit. In our practice, the check starts with inspecting the tubes, brazing, and evaporator: oil traces at connections, frost at one point, hissing during operation are direct signs of depressurization. We recharge freon only after fixing the leak; otherwise the procedure is pointless. Refrigerant R600a and R134a are charged by weight, not by eye: undercharging gives weak cooling, overcharging puts extra load on the unit. When a technician offers to just top up without finding the leak, the refrigerant will escape again in a few weeks—the correct order is the opposite: find the leak, fix it, then recharge.
The compressor is replaced when the motor won't start, runs overheated, or has lost performance, and the technician confirms this with diagnostics, not just by sound. A click and silence when turned on, a hot housing, no pressure at the outlet—these are reasons to check the unit with a multimeter and manifold gauge. At Tech Service, we make that call after measuring the windings and circuit pressure, not based on a single symptom. Before replacing the compressor, the specialist checks the start relay and the electronic control board—sometimes a 'dead' motor is actually fine and just won't start because of the relay or electronics. So we rule out the cheap causes first, and only then suggest replacing the unit. Diagnostics are free, and there's a 1-year warranty on labor and parts—this removes the risk that the replacement turns out to be unnecessary.
The compressor compresses the refrigerant and keeps it circulating in the circuit, and it most often fails due to overheating, wear, or voltage spikes. The motor draws in refrigerant vapor, compresses it, and pushes it through the tubes—this keeps the evaporator cold and releases heat in the condenser. Overheating occurs when the condenser is clogged or the fan is faulty, wear accumulates over the years, and a sudden power surge can burn out the winding. The unit rarely fails on its own—if it burned out, it's worth checking whether the relay, board, or power supply was the cause, otherwise the new motor will meet the same fate. Understanding this helps you avoid agreeing to replace the unit without an explanation of the cause.
An error code on the display is a hint, not a verdict. Let's look at which component it points to, how the electronics affect cooling, and what steps the technician takes.
The error code points to a specific component — a sensor, fan, module, or defrost system — but the technician confirms the exact cause through diagnostics. Each brand has its own table: with Bosch, the combination of flashing indicators and the alphanumeric code on the panel are read according to the manufacturer's instructions, while on other models the same symptom means a failed air sensor or a defrost fault. The electronic board detects a deviation in the signal from the temperature sensor and displays it on the screen, so the same combination on different series can refer to different parts. Don't reset the error by turning the appliance back on — if the code returns, the cause is still there, and a cleared record makes troubleshooting harder. The technician needs to see the original state, not a wiped controller memory.
We test and set up the control board on site or at the service center — it controls the compressor, fans, and sensors. A Tech Service specialist checks the traces, relay contacts, and module power, compares the temperature sensor readings with reference values, and verifies how the controller responds to compressor start commands. When the module is working but there's no cooling, the search moves to the actuators — the start relay, fan, or compressor motor. Setup includes reflashing and calibration for the specific model, not just a visual inspection of the traces, so afterward the board correctly reads sensor signals and manages the cycles. Electronics often suffer from voltage spikes and moisture, so after replacement it's worth checking the refrigerator's power supply too — otherwise the new part will burn out the same way.
When the refrigerator won't shut off and gets colder and colder, the usual culprit is the thermostat or temperature sensor that isn't sending the cooling signal. A mechanical thermostat loses sensitivity to cold over time, and an electronic sensor produces distorted resistance — the controller "thinks" the compartment is warm and keeps the compressor running. On two-compartment and No Frost models, these components are separate in the fridge and freezer sections, and failure of one disrupts the entire defrost cycle. Don't confuse a sensor failure with an incorrect regulator setting — if you recently changed the setting, return it to the middle value and observe for a day. Diagnostics will show which part has failed — replacing a sensor is simpler than restoring a compressor that ran nonstop.
Let's break down what the warranty covers, what to do if the problem comes back, and when repairs no longer make sense — with typical situations explained.
We provide a 1-year warranty on the work performed and on the parts installed — if the appliance breaks down again, contact us under warranty, and a specialist will investigate the cause again. The term is the same for the compressor, thermostat, sensors, and control board, as well as for work on refilling the circuit and soldering connections. For repeat warranty calls in Almaty, we follow the same procedure as the first time: an engineer arrives, checks the component, and records exactly which element failed. In my view, it's fairer to separate two scenarios right away. The warranty covers the work performed and the part installed — if the breakdown occurs in a different component, that's a separate case, and the specialist will say so directly, without trying to pass off unrelated wear as our fault.
Repairs don't make sense when the cost of labor and parts approaches the price of a new appliance, or when the body and circuit are seriously damaged. The second case is through-and-through corrosion of the evaporator inside the foamed body: to reach the unit, you have to open up the insulation, and airtightness isn't always restored afterward. The third scenario is cracked inner plastic and separated seams in the chamber, when cold simply won't hold. Old Soviet refrigerators are repaired more often than you might think: they have a simple motor and a repairable circuit, so "just buy a new one" isn't always the right call. Moreover, in such models, replacing the start relay or thermostat gets the unit running again, while modern electronics with an inverter compressor can sometimes cost more when the board fails. The technician names the likely outcome after free diagnostics — use that to decide.
We accept payment via Kaspi QR, Kaspi Red (instalments), bank card, cash, or bank transfer for companies, and the technician names the price after free diagnostics — before work starts, you know what you're paying for. Cash, card transfer, and QR code payment are all equally fine, so you choose how to pay, including when you need refrigerator repair in Almaty affordably without extra hassle. Diagnostics are free, the engineer arrives within 60 minutes anywhere in the city, and we don't charge for the inspection even if you decline the work. We quote the price after checking, because the cause may not be what the symptom suggested — that way you don't pay for work you don't need. In practice, it looks like this: the engineer opens the back panel, checks the compressor and circuit pressure, then names the scope of work and the final amount. Only after your approval does he pick up his tools.
The refrigerator stopped cooling, started leaking, or showed an error code — most often it's one of the typical faults that can be fixed on-site after free diagnostics.
90brands
We work with every brand sold in Kazakhstan — from Samsung, LG and Atlant to Biryusa, Indesit, Stinol and rare imported makes. Can’t find yours in the list? Call anyway — a technician will come and take a look.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your refrigerator stops working, first check the outlet, the power cord, and the thermostat setting, and after defrosting let it stand for a while.
4 February 2026 · 12 minutes read
If your refrigerator isn't cooling but the light is on, the cause is usually one of the components in the cooling circuit: the compressor, thermostat…
10 December 2025 · 13 minutes read
If your dishwasher won't drain, the most common culprits are a clogged filter or drain hose; less often, it's the pump, impeller…
24 March 2026 · 12 minutes read
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
If your microwave isn't heating but the light and turntable still work, the problem is usually one of the high-voltage components — the magnetron, diode…
15 February 2026 · 12 minutes read












