experience10 yearsMaksim S.
Graphics card repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 046 88 53Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Free diagnostics, technicians with 4 to 20 years of experience.
Our own technicians4 to 20 years of experience




Repair prices
Below are the symptoms owners often notice. The technician will pinpoint the exact cause during diagnostics.
power supply, cable, button
from18 000 ₸
fan, bearing, mounting
from4 000 ₸
thermal paste, heatsink, fan
from4 000 ₸
chip, ribbon cable, contact
from9 500 ₸
capacitors, diodes, fuse
from18 000 ₸
wear, dust, bearing
from4 000 ₸
firmware, connector, chip
from5 500 ₸
hash board, chip, power
from10 500 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1–3 daystime
from 4,000 ₸cost

BeforeAfter5 steps

Five steps from request to checking the equipment.
Submit a request, describe the symptom and the miner model — the technician will prepare for the visit.
A technician arrives within 60 minutes anywhere in the city, bringing tools and diagnostic equipment.
The technician lists the replacements and scope of work, and you confirm the list before repairs begin.
Once the scope and price are approved, the technician performs the repair and replaces parts on site.
The technician demonstrates the miner starting up and confirms the warranty terms on labor and parts.
The computer and laptop repair department in Almaty has 7 technicians with 6 to 15 years of experience.

The department has 7 specializations — they are listed on the technicians' cards.
experience10 yearsGraphics card repair technician
experience6 yearsPC and laptop diagnostics technician
experience8 yearsLaptop repair engineer
experience10 yearsSoftware installation specialist
experience7 yearsPC and laptop repair technician
experience13 yearsDiagnostics and virus removal specialist
experience15 yearsConsultant
We reply during working hours
Describe the issue and a convenient time — the technician will arrange a visit and check the equipment on site.

Warranty question? Call us
+7 (778) 046 88 537 898 reviews of repairs at TECH SERVICE in total
Александра Н.Order No. ZK-2025/635 · 13 September 2025
oursОбращаюсь не первый раз, поэтому есть что сказать. Функции все на месте, ничего не отвалилось.
Ержан А.Order No. 113462 · 23 July 2025
oursОбращался в сервис по совету знакомых. Оформили всё официально, с гарантией. Приняли быстро, объяснили, что и как будет. Мастер посмотрел, назвал причину, всё разложил по полочкам. Рекомендую.
Алия Ш.Order No. ZK-2023/279 · 5 August 2023
oursДолго откладывал, но пришлось обратится. Проверили при мне, показали результат. Отношение нормальное, без высокомерия. Запчасть нашли без проблем. По срокам не подвели. В целом остался доволен.
Тимур А.Order No. ZK-3532 · 11 July 2023
oursОбращаюсь не первый раз, поэтому есть что сказать. Друг посоветовал, у него похожая история была. Всё объяснили простыми словами. Дали гарантию и рекомендации на будущее. Оформили всё официально, с гарантией. Приняли быстро, объяснили, что и как будет. Спасибо за работу!!
Нурлан Б.Order No. TS-2305-273 · 6 June 2023
oursВыбирал между несколькими сервисами, остановился на этом. Техника на гарантии уже не была, так что выбор был свободный. Отношение нормальное, без высокомерия. Работу сделали в тот же день. Диагностика заняла минут двадцать. Проверил дома — всё на месте, ничего не забыли!!
Нурасыл М.Order No. TS-1904 · 31 March 2023
oursНужен был ремонт, искал вариант поближе. Выбирал по отзывам в 2ГИС, времени на эксперименты не было. Дамир М взялся за то, от чего другие отказались. Перезвонили, когда можно было забирать. Приняли быстро, объяснили, что и как будет. Сделали ровно то, о чём договаривались. Не идеально, но честно.
Айнур М.Order No. 81461 · 20 December 2021
oursВыбирал между несколькими сервисами, остановился на этом. Друг посоветовал, у него похожая история была. Сделали аккуратно, следов разборки не видно.
Серик М.Order No. 17104 · 20 February 2020
oursНашёл по отзывам, решил попробовать. Проверили при мне, показали результат. Дали гарантию и рекомендации на будущее. По срокам не подвели. Работу сделали в тот же день. Отношение нормальное, без высокомерия. Диагностика заняла минут двадцать. Всё объяснили простыми словами. Приняли технику, выдали квитанцию. Хороший сервис, побольше бы таких.
Николай Ч.Order No. ZK-6559 · 20 February 2017
oursОбращался в сервис по совету знакомых. Нужен был счёт и чек, у нас техника на балансе организации. Отдельно скажу про мастера: Никита М — спокойный, без лишней суеты. Диагностика заняла минут двадцать. Хороший сервис, побольше бы таких)
Карина А.Order No. ZK-2016/159 · 5 September 2016
oursПозвонил утром, к обеду уже всё решили. С чистой совестью советую. Запчасть нашли без проблем.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionYes, the power supply of an ASIC miner is repaired as a separate unit without touching the hash board. During free diagnostics, the technician checks the output voltages and power circuits, then agrees on the scope of work.
Yes, hash boards of Antminer and Whatsminer ASIC miners are repaired at the component level: burnt chips are replaced and power circuits are restored. If the board is damaged too severely, the technician will suggest replacing the unit after diagnostics.
Running with an error on the hash board overloads the working chips and power circuits, so the fault spreads. The ASIC miner may go into protection or stop starting, and repairs will cost more.
First, check the cables and connectors between the hash board and the control board, their fit and absence of damage. If the board is still not detected after reconnecting, diagnostics are needed — the cause may be in the board itself or in the power circuits.
The hash board of an ASIC miner is more often repaired: burnt chips are replaced and power circuits are restored. A complete replacement is needed for severe damage, which the technician determines after diagnostics — it depends on the model.
Yes, for ASIC miner repair in Almaty we provide a 1-year warranty on labor and parts. It covers the work performed by the technician and the installed parts, and the terms depend on the specific case.
Tech Service repairs ASIC miners in Almaty: our technician arrives at your home within 60 minutes or you can drop off your equipment at our service center. Diagnostics are free, 1-year warranty on labor and parts, technicians have 4 to 20 years of experience. The technician gives you the price after diagnostics, and you can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies.
Owners come with a symptom, not a diagnosis: "won't start," "hums and shuts down," "throws errors." Each symptom has a specific cause—let's go through three common scenarios and where to start checking.
If your ASIC won't start or shuts off after a minute, it's usually the power supply or the power circuit on the hash board, not the whole device being fried. A voltage spike in the grid damages the power supply, it stops delivering the required 12 volts, and the board controller doesn't start the boards. The second scenario is a short in the circuit on the hash board itself: the device starts but protection cuts power almost immediately. The third, less obvious one is voltage drop under load: the outlet or extension cord can't handle the current, and the miner shuts down even though it's fine. Diagnostics start with measuring the power supply's output voltage and inspecting the board for signs of overheating. Before calling a technician, check if the outlet can handle the load and look for any burn marks near the power connector—this will narrow down the search and save diagnostic time.
An ASIC overheats and shuts down on protection when heat dissipation is compromised: radiators are clogged with dust, thermal paste has dried out, or a fan isn't spinning. Dust compacts between the radiator fins and acts like a blanket—heat from the ASIC chips doesn't escape into the air and stays on the board. Dried thermal paste loses conductivity, and even a clean radiator can't remove heat from the die. A cooling fan with a worn bearing spins slower than needed, and thermal protection triggers based on sensors and shuts down the miner when it exceeds the threshold. Sustained overheating is more dangerous because chips degrade gradually—the miner still runs but hash rate quietly drops, so cleaning should be planned before errors appear. If the fan is already louder than usual and the case has gotten hotter, don't put off maintenance: at an early stage, cleaning and replacing thermal paste is usually enough.
A hash board error and dropped hash rate usually point to a faulty chip or power circuit on the board itself, not a problem with the whole miner. ASIC chips work in a chain, and one failed chip drags down its neighbors—the board marks them as faulty and reduces overall performance. Moisture on contacts after temperature changes or condensation gives the same symptom: the board sees an open circuit and throws an error. Diagnostics include testing power circuits and checking chips on a test bench—this shows exactly what failed. One bad board drags down the overall hash rate and loads the others—so it's better to diagnose it right away rather than wait for the error to turn into a complete failure.
We break it down at the component level: what we take on, where replacement is more honest than restoration, and how to tell a power unit defect from a computing module failure.
We repair the computing modules and power supply units of ASIC miners and, based on diagnostic results, tell you what makes more sense — getting the component back in working order or installing a new one. On the board, we check the ASIC chips, power circuit, and controller: a blown chip is replaced, while a broken trace or dried-out capacitor is restored by soldering. In the power supply, we check the output voltage, connectors, and signs of overheating — a voltage drop under load is more often fixed by installing a new unit than by rebuilding. Both units produce similar symptoms, so we make a decision only after checking both, not based on a single sign like "won't turn on" — this way the technician doesn't replace a working part. In my opinion, a good half of the failures that owners describe as "the module burned out" actually turn out to be sagging power. Our ASIC repair starts with free diagnostics of both units — so the technician doesn't replace a working board instead of a cheap power restoration.
| Unit | What we check | Work option |
|---|---|---|
| Power supply | output voltage, connectors, signs of overheating | restoration or replacement |
| Hash board | chips, power circuit, errors | repair or new board |
| Fans | rotation, noise, bearing | cleaning or replacement |
| Cooling | dust, thermal paste, heatsinks | maintenance |
| Controller | startup, firmware, communication with boards | diagnostics and setup |
We work with Antminer, Whatsminer, Avalon, and Innosilicon, including the Antminer S9, S17, L3+ lines and other common models. For S17 and S19, we more often deal with chip degradation on the computing module; for Whatsminer, with power units and controller circuitry; and for Avalon and L3+, cooling often suffers due to tight layout. Restoration on these platforms differs in the set of spare parts and firmware, so please provide the model and hashrate when you request service — the technician will arrive with the right tools. Bringing an old S9 back to life isn't always worth it — the specialist will honestly tell you when the work is justified and when the cost is comparable to buying other equipment. Our experience of 4 to 20 years per technician allows us to predict the likely scenario for each line in advance and not promise more than we can deliver.
We show the miner's journey step by step — from request and free diagnostics to the repair itself and warranty, so you understand what happens at each stage and what the technician is responsible for.
Diagnostics are free with us: the technician checks the power, hash boards, cooling, and controller and identifies the cause of the failure before work begins. First, we check the power supply under load — a voltage drop on the 12V lines causes startup failure and false errors on the hash board. Then we test each board separately to find the specific chip rather than replacing the whole unit: pinpoint search saves money on parts and reduces downtime. We also inspect the cooling separately: a clogged heatsink and dried thermal paste send the ASIC into thermal protection before the automation kicks in, so it's better not to delay cleaning and paste replacement. We test the controller for communication with the boards and firmware correctness. It's during diagnostics that it becomes clear whether any work is needed at all — sometimes cooling maintenance is enough, and the technician will tell you so directly.
The time depends on which component failed and whether a part needs replacement, so the technician gives the exact time after diagnostics. Replacing the power supply and servicing the cooling system usually take less time than working on the hash board: there you need to find the specific chip, check the circuitry, and make sure the board can handle the load. The model also affects the timeline — Antminer, Whatsminer, and Avalon have different board layouts and different access to components. A technician visit within the city takes 60 minutes, so the inspection doesn't stretch into days of waiting. If the failure affects the hash board and not just cooling, the work almost always takes longer — keep this in mind when planning equipment downtime.
A miner has a peculiarity: it's heavy, noisy, and demanding on power. So let's break down when a site visit is really needed and when it's smarter to bring the equipment to our workshop.
We send our specialist to your home within 60 minutes anywhere in the city if the failure can be found and fixed on-site without disassembling boards. Most often this means checking power, connections, and cooling: the technician opens the case, inspects the connectors, tests the connection, and assesses whether the device has gone into thermal protection. In a container or on a rack, this approach is especially convenient — you don't need to remove the ASIC and arrange transportation. A visit saves time when the equipment is running on-site and its dismantling and transport are risky in themselves. If the inspection shows that work on the hash board is needed, the technician will tell you honestly and suggest bringing the equipment to us.
If you need work on the hash board or power supply at the component level, it's more convenient to bring the miner to us, where we have the conditions for precise work. At the client's site, you can't set up a proper check of components: the hash board needs to be carefully removed, the chips and traces inspected, and the power supply disassembled and its components tested. Such operations require a calm environment and good lighting, not a cramped container. We are a direct contractor and perform work at the client's home or in our workshop — no middlemen between you and the specialist. This honest division of formats benefits you: we don't push for a visit where it won't help, and we don't drag equipment to us if the issue can be solved on-site.
| Situation | Format | Why |
|---|---|---|
| Won't turn on, suspected power issue | home visit | on-site check without transportation |
| Overheating, noise, dust | home visit | cooling maintenance on-site |
| Hash board error | service center | requires precise work with the board |
| Power supply repair | service center | requires disassembly and component testing |
| Miner in a container | home visit | dismantling and transport are risky |
Let's break down exactly what work the one-year warranty covers, why a direct contractor is more accountable for the result than a middleman, and how the technicians' experience affects diagnostic accuracy.
We provide a 1-year warranty on labor and parts, so if the repaired unit fails again, you come back to us instead of looking for a new technician. The coverage applies to both sides of the work: the quality of soldering or component replacement, and the parts themselves — the hash board, power supply, chips. A miner runs under constant heavy load, and a hidden defect in a part doesn't show up immediately but after weeks of operation. A year of coverage gives enough time to test the replaced unit under real mining conditions, not in a hothouse. In my view, the warranty on parts is more important here than on labor: soldering is visible right away, while the lifespan of a new power supply or board can only be checked under load. So keep the service record — we use it to handle your claim without any arguments.
Tech Service is a direct contractor: our technician comes to you, not a subcontractor from an aggregator, so we are responsible for the work and the warranty. There is no dispatcher between you and the specialist who forwards the request to a third party and loses details. This shows in the quality of communication: the technician opens the case himself, retrieves the error log, and explains exactly what failed — the hash board, power circuit, or cooling. When the chain is short, it's easier to get a clear answer instead of a faceless "needs repair." In our experience, this saves time: the request isn't passed between contractors, and diagnostics aren't repeated twice. Moreover, the same technician who did the work handles the warranty case — he doesn't have to reconstruct someone else's work from memory.
Our technicians have 4 to 20 years of experience, and you can pay for service in any convenient way — via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies. Diagnostics are free, and the specialist quotes the cost of work only after diagnostics, once the cause of the failure is identified. Experience with miners matters because symptoms are similar across models: overheating, a failed hash board, and a sagging power supply produce almost the same picture on screen. An experienced technician distinguishes them by logs and measurements, not by replacing components at random. This saves both time and parts that would otherwise be swapped "just in case." For residents of Almaty, a technician visit within the city takes up to 60 minutes. And one more thing: don't rush to agree to the first diagnosis — ask them to explain why they chose that particular component.
Some miner breakdowns can be prevented by timely cooling maintenance. Here's what preventive service includes, how often to do it, and what steps to take right now while the device is still working.
We perform dust cleaning and cooling maintenance: we blow out the heatsinks, check the fans and the condition of the thermal paste so the ASIC doesn't go into thermal protection. Clogged heatsink fins and thickened thermal paste reduce heat dissipation — chips get hotter under the same load, fan speeds increase, and the case gets louder. At Tech Service, people bring in Antminer, Whatsminer, and Avalon for service: each line has its own board layout and cooling mount, so we disassemble and reassemble according to the specific model's diagram, and after reassembly we check how the temperature behaves under load. We also inspect the fan bearings separately: wear in them adds vibration and noise before the temperature even starts to rise. Dust on heatsinks acts slowly and unnoticed — the device keeps working, but the chips get hotter, so it's better not to put off cleaning until the first error: removing a layer of dust in advance is cheaper than replacing a burned-out hash board.
How often you need service depends on the conditions: in a dusty room or container, cooling gets clogged faster than in a clean one, so the guideline is regular checks, not a one-time procedure. Mining containers and utility rooms collect dust and lint within weeks, while in an apartment or office with air filtration, radiators stay clean longer. Overheating leads to the miner shutting down for protection: the firmware stops operation when chip temperatures exceed the threshold, and the hashrate drops to zero. If the device has become noisier or the temperature has risen under the same load, that's a signal to check the cooling earlier than usual — a worn fan or dried thermal paste produces exactly this picture, and at an early stage, servicing without replacing components is enough. It's also worth inspecting the airflow path: a dented case or a shifted baffle changes the flow and adds a couple of degrees to the operating temperature.
We've gathered the key things to keep in mind before contacting us: what factors affect the cause of the failure, why a check is needed, and what to look for in the warranty.
7brands
We work with mining equipment from popular manufacturers. Choose a brand to learn more.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your laptop screen is broken, turn the device off first, don't press on the display, and check the picture through an external monitor.
12 March 2026 · 11 minutes read
If your laptop freezes, the first thing to do is restart it and check Task Manager to see what's loading the CPU and memory.
25 January 2026 · 12 minutes read
If your computer won't turn on, start simple: check the outlet, power cable, switch on the power supply, and the power button.
19 January 2026 · 13 minutes read
If your laptop won't boot, first determine which of two states you're in: the device doesn't respond to the power button at all…
13 December 2025 · 12 minutes read












