experience9 yearsRuslan Ts.
Washing machine and refrigerator repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (775) 030 02 94Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
We arrive within 60 minutes anywhere in the city. Diagnostics are free, and we name the cause and the cost before any work starts.
Our own technicians4 to 20 years of experience




Repair prices
Common symptoms and likely causes, starting with the most frequent. The technician names the exact cause after free diagnostics.
no gas, clogged nozzle, thermocouple fault
from4 000 ₸
clogged nozzle, shifted burner cap, moisture
from4 500 ₸
clogged nozzle, low gas pressure
from4 000 ₸
dead battery, oxidized contacts
from4 500 ₸
worn seal, loose connection
from4 000 ₸
motor fault, belt slipped off
from4 000 ₸
thermostat fault, worn door seal
from8 000 ₸
damaged cord, oxidized plug
from4 000 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1 visittime
from 4 500 ₸cost

BeforeAfter5 steps

From request to final check in five steps, with free diagnostics.
Describe the symptom and the stove model so the technician brings the right tools.
The technician confirms the model, the symptom and the connection type and brings the parts needed.
The technician shows and explains what will be taken apart and offers repair options.
The technician prepares the work area, protects surfaces and replaces parts in the agreed order.
Check the ignition of every burner, the flame and the rotisserie yourself, and ask the technician any questions.
The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience12 yearsGeneral household appliance repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsExpert washing machine repair technician
experience8 yearsField refrigerator repair technician
experience8 yearsSenior washing machine repair technician
experience11 yearsDishwasher repair technician
experience9 yearsWashing machine repair technician
We reply during working hours
Describe the symptom and the stove model, and the technician will bring the right tools and parts and arrive anywhere in the city within 60 minutes.

Warranty question? Call us
+7 (775) 030 02 947 898 reviews of repairs at TECH SERVICE in total
Диана М.Order No. 76639 · 8 March 2025
oursПриехал без записи, приняли. Ораз подсказал, как продлить жизнь технике. Работу сделали в тот же день. Могу рекомендовать)
Николай Ч.Order No. 2025-9120 · 9 January 2025
oursПришёл по записи, всё прошло спокойно. Пробовал найти мастера в своём районе, но все были заняты. Дамир М подсказал, как продлить жизнь технике!!
Станислав К.Order No. 14721 · 7 April 2023
oursОбращаюсь не первый раз, поэтому есть что сказать. Приняли быстро, объяснили, что и как будет. Работу сделали в тот же день. Проверили при мне, показали результат. Оформили всё официально, с гарантией. Цена не изменилась ни на тенге. Приняли технику, выдали квитанцию. Работали аккуратно, ничего не поцарапали. Не идеально, но честно.
Сауле Н.Order No. 801205 · 20 February 2023
oursОбращался в сервис по совету знакомых. Прочитал кучу отзывов, половина — реклама, но тут вроде живые. Ораз объяснил причину так, что понял даже я.
Вероника П.Order No. 29987 · 28 March 2022
oursБыла срочная поломка, нужен был мастер сегодня. Не пожалел ни разу. Перезвонили, когда можно было забирать.
Павел Ш.Order No. 2022-7882 · 29 January 2022
oursНужен был ремонт, искал вариант поближе. Выбирал по отзывам в 2ГИС, времени на эксперименты не было. Турарбек Кайрош объяснил причину так, что понял даже я.
Евгений М.Order No. 864519 · 16 September 2021
oursПозвонил утром, к обеду уже всё решили. Дамир М снял деталь, показал износ, вопросов не осталось. Цена не изменилась ни на тенге. Сервис нормальный, обращусь ещё.
Индира П.Order No. ZK-2021/920 · 20 May 2021
oursПервый раз сюда, до этого чинился в другом месте. По срокам не подвели. Отношение нормальное, без высокомерия. Не пожалел ни разу
Ксения И.Order No. 685771 · 23 October 2019
oursБыла срочная поломка, нужен был мастер сегодня. До этого обращался в другой сервис, там только развели руками. Максим Снегирев перезвонил, когда всё было готово. Работу сделали в тот же день. По срокам не подвели. Отношение нормальное, без высокомерия. Сервис нормальный, обращусь ещё.
Ерасыл Б.Order No. ZK-8883 · 15 May 2016
oursПозвонил утром, к обеду уже всё решили. Прочитал кучу отзывов, половина — реклама, но тут вроде живые. Дмитрий Радионов всё объяснил и не пытался впарить лишнее.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionStove replacement at the state's expense is available to certain eligible categories under akimat social programs, usually upon application. We repair gas stoves rather than handle benefit-based replacements.
Moisture got onto the spark plug or wiring, and the ignition module keeps sending a spark. Dry the stove and remove water around the burners; if the clicking continues, a technician needs to take a look.
You can remove and blow out the nozzle, but it's easy to damage or knock out of adjustment, and then the flame will become uneven. If the burner burns weakly, it's safer to have a technician clean it during gas stove repair.
Most likely the thermocouple isn't holding, or the gas control cuts off the supply when the sensor doesn't detect a flame. It depends on the model: a technician will check the thermocouple and valve and replace the worn part.
You need to replace the jets for the different gas type and check the connections for leaks, otherwise the flame will soot. A technician does this during gas stove repair, selecting jets for the model.
If the problem involves the ignition, thermocouple, or valves, repair is usually worthwhile and extends the stove's service life. When the main components and body are worn out, the technician will honestly tell you after free diagnostics whether replacement is more cost-effective.
Tech Service repairs gas and dual-fuel stoves with its own technicians: a specialist arrives within 60 minutes anywhere in the city, checks the burners, ignition, flame failure protection and oven free of charge, then fixes the stove on site or takes it to our service. We give a 1-year warranty on labor and parts and accept payment via Kaspi QR, Kaspi Red, card, cash, or bank transfer for companies.
The same symptom can come from different parts: clicking with no flame, a burner that goes out and soot all point to different components. Below is a fault map and the signs you should not put off.
| Complaint | Likely part | What is checked first |
|---|---|---|
| Clicks but won't light | spark electrode, ignition module | spark and moisture on the electrode |
| Goes out when the knob is released | thermocouple, safety valve | carbon buildup and thermocouple position |
| Weak, yellow flame | nozzle, burner head | clogging and burner head seating |
| Knob is hard to turn | burner valve | valve grease and stem |
| Pops when lit | burner, spark electrode | spark gap and clean burner ports |
| Oven goes out after a minute | oven thermocouple | sensor position in the flame |
| Baking burns on the bottom | thermostat, door seal | flame response and door fit |
If one burner misbehaves, the cause is almost always in its own parts, not in the gas supply to the stove. The shared supply line feeds every burner at once, so when it fails, all burners weaken and go out together. When only one acts up, the search narrows to its burner head, nozzle, thermocouple and valve. Our free gas stove diagnostics start with exactly this comparison: the technician lights the burners one by one, looks at the flame color and height and checks whether the flame stays on after the knob is released. Our technicians, with 4 to 20 years of experience, can tell a clog from a worn part by the flame alone, before taking anything apart. Before you call, note which burner the problem started on and at which knob position it appears (low flame or full power), since this noticeably shortens the search for the fault.
Most burner complaints come down to three parts: the ignition spark, the flame sensor and gas metering. Below is how each of them fails and what the stove owner sees when it happens.
Nonstop clicking almost always means moisture and a short in the button and ignition module, while total silence means a broken wire, a failed button and, less often, a failed module. Electric ignition is simple: a button (on some models, turning the knob) closes the circuit, the module produces high voltage and a ceramic electrode next to the burner makes the spark. Water from a soup that boiled over or from cleaning runs under the knobs, and the module starts clicking on its own even with the burners off. In these cases we dry and check the contacts, inspect the electrode ceramic for cracks and replace the module only if it is actually burned through. The opposite also happens: there is a spark, but it jumps past the burner because the electrode is covered in carbon or the burner head sits crooked. After wet cleaning, give the stove a few hours to dry and do not press the igniter right away, so the module lasts much longer.
If the flame goes out as soon as you release the knob, the flame failure device is not working: either the thermocouple or the solenoid valve. A thermocouple is a thin metal rod next to the burner: in the flame it heats up and produces a small current that keeps the valve open. While the knob is pressed, your hand holds the valve open, and after you let go everything depends on the thermocouple. Carbon on its tip, a shift out of the flame zone or an oxidized contact all weaken the current, and the valve closes. Our gas stove technician first cleans and repositions the sensor, checks its contact with the valve and only then decides what to replace: the thermocouple, the valve or sometimes both. Thermocouples also differ in length for burners of different sizes, so the part is matched to the specific burner. Holding the knob for a long time and trying again and again is pointless: if the safety device does not hold after normal warm-up, the stove needs an inspection, not patience.
A weak, yellow flame comes from a clogged nozzle, a shifted burner head and nozzles that do not match the gas type. A nozzle is a brass part with a calibrated hole through which gas enters the burner; grease and burnt sugar narrow the hole, and the burner burns low. A burner head with clogged ports, or one seated at an angle, gives a ragged flame on one side. If the stove is switched from bottled to mains gas without changing the nozzles (or the other way round), the flame changes on all burners at once: it either lifts off the burner or turns yellow and leaves soot on the bottom of pots. A healthy flame is blue and even, with a faint purple edge, and makes no noise. Never clean a nozzle with a needle, drill bit or wire: the hole widens, the calibration is lost and the part has to be replaced entirely.
The oven has its own burner, flame sensor and thermostat, so its faults are different from burner complaints. We cover ignition, uneven heating and the order in which the oven cavity is checked.
The oven goes out a minute after lighting when its thermocouple does not heat up or the safety valve does not hold the gas. The oven burner is long and sits under the floor of the cavity, so over time its flame sensor gets coated with carbon from spilled fat and burnt food. Besides the thermocouple, we check the burner itself: clogged ports give a flame along only part of its length, and the flame simply never reaches the sensor. On stoves with electric oven ignition we check the electrode separately, as it sits where fat drips from the baking tray. Sometimes haste is to blame: if the knob is not held in long enough, the valve does not have time to latch. If ignition fails, do not relight the oven right away; open the door and air the cavity for a minute or two so the trapped gas does not cause a pop.
If baking burns on the bottom and stays raw on top, the thermostat, the door seal or, less often, the oven burner is to blame. A thermostat with a capillary sensor inside the cavity reduces the gas flow when the set temperature is reached, and when worn it keeps the flame on full or, on the contrary, turns it down too early. A torn or hardened seal lets heat escape, and the top of the cavity stays cold while the bottom is red hot. A burner with partly clogged ports heats unevenly, so one edge of the tray burns while the other stays pale. In our service, gas stoves with a faulty thermostat are taken apart more carefully than usual because a thin capillary tube runs to it and is easy to break. You can check the seal without a technician: close the door on a sheet of paper and pull it; if it slides out with no resistance, the seal no longer holds heat.
| Oven part | Sign of a fault | What we check |
|---|---|---|
| Burner | flame along only part of it | clean ports and seating |
| Thermocouple | goes out when the knob is released | carbon and position in the flame |
| Safety valve | won't hold with a hot thermocouple | contact and activation |
| Thermostat | burns food or underheats | flame response to the knob |
| Oven spark electrode | no spark in the cavity | carbon, ceramic cracks, wire |
| Seal and hinges | heat escapes around the door | fit along the whole edge |
| Timer and lamp | no light, no countdown | power and contacts |
A gas smell is the only fault where the order of actions matters more than the cause. We explain what to do in the first minutes, who is responsible for the pipe and who for the stove itself, and how any gas work should end.
| Section | Who is responsible | When to call |
|---|---|---|
| Pipe and valve up to the stove | gas utility | leak, smell near the pipe |
| Connection to the mains | gas utility | first connection, moving the stove |
| Cylinder and regulator | gas supplier | smell near the cylinder, cylinder swap |
| Connection hose | gas utility or technician | cracks, old hose |
| Valves, thermocouples, nozzles | repair technician | burner faults |
| Oven and thermostat | repair technician | no heat, goes out, burns food |
| Ignition, timer, light | repair technician | electrical part not working |
We finish any work on the gas part with a soapy water test of the joints. The solution is brushed onto the valve nuts, the stove inlet and both ends of the hose, then the gas is turned on: bubbles even the size of a pinhead reveal a leak. Our in-home gas stove technician repeats the test after every tightening and only then lights all burners and the oven to check the flame and the flame failure device. We inspect the hose separately: rubber hoses harden over time and crack at the fittings, while corrugated steel ones suffer from kinks behind the stove. If the stove was moved during cleaning, the hose is often twisted without the owners knowing. As a last step, we make sure every knob returns to the off position without play and does not turn past the stop. An old hose is worth replacing at the very first repair, even if it still holds: a crack appears suddenly, and then it becomes an emergency call.
Step by step, from the request to checking the result: when the specialist arrives, what the inspection includes, where the work takes place and what the warranty covers.
The technician arrives within 60 minutes anywhere in the city and checks the stove free of charge. We start in-home gas stove repair in Almaty with a short conversation: what happened, on which burner, how long ago the fault appeared and whether the stove was moved. Then the specialist shuts off the gas, removes the grates and burner heads, inspects the burners, checks the spark, the thermocouples and how the valves turn, and then lights the burners and watches the flame at every setting. The oven is checked separately: ignition, flame holding, thermostat operation and door fit. The work is done by technicians with 4 to 20 years of experience, so the cause is named after the inspection, not from a description over the phone. You hear the cost before the work starts, and the decision to repair stays with you. Before the visit, clear access to the valve and the hose behind the stove and take cookware off the burners so the inspection goes faster.
| Work | Where we do it | What we check afterwards |
|---|---|---|
| Cleaning nozzles and burner heads | at home | flame color and height |
| Replacing a burner thermocouple | at home | flame holding without the knob |
| Ignition module repair | at home | spark at every burner |
| Valve greasing and replacement | at home | knob movement and leak tightness |
| Connection hose replacement | at home | joints with soapy water |
| Oven thermostat replacement | at home, sometimes in the service | cavity temperature |
| Safety valve replacement | at home, sometimes in the service | activation after warm-up |
| Electrics of a dual-fuel stove | at home, sometimes in the service | heating and timer operation |
We give a 1-year warranty on labor and parts we install, so replacing a thermocouple, a valve or an ignition module is covered both for the part itself and for its installation. We name the gas stove repair price after the free inspection, once it is clear which part has failed and what needs to be done with it: cleaning, adjustment or replacement. The amount of work varies widely: clearing one nozzle and replacing an oven thermostat are very different jobs, and a fair estimate without an inspection is impossible. You can pay in whatever way suits you, as we accept Kaspi QR, Kaspi Red, card, cash or bank transfer. We are a direct service provider, not a middleman: your stove is repaired by our technician, and the same service that sent him is responsible for the result. Keep the name of the replaced part: if the symptom returns, this speeds up the check and helps tell a new fault from the old one.
Not every stove is worth repairing, and a repaired one lasts longer with proper care. We look at how to make the decision and how not to bring the fault back yourself.
A stiff knob is a sign of dried-out or dirty valve grease, and we lubricate the valve with heat-resistant grease made for gas fittings. Inside the valve a tapered plug rubs against the body, and the grease both makes turning easier and seals the gap that gas would otherwise pass through. Over time it dries out from the heat, grease and cleaning products get into it, and the knob has to be forced. We take the valve apart, clean the plug and seat, apply a fresh layer and test the joint for leaks, and if the plug is scored, we replace the whole valve. Never force a stiff knob: the stem or even the plastic bushing will break. Vegetable oil, heavy machine grease and general-purpose spray lubricants are not suitable for valves: they cannot handle the heat, dissolve what is left of the old grease, and within a couple of weeks the knob turns even harder.
We have put together a short summary to help you understand a stove fault before the specialist arrives, avoid making it worse yourself and calmly decide whether the appliance is worth fixing.
25brands
Pick a brand to open its page and learn about repairing specific models.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your oven isn't working, first check the outlet, the circuit breaker in the panel, and the selected mode, then assess the symptom: not heating…
3 October 2025 · 12 minutes read
If your dishwasher won't drain, the most common culprits are a clogged filter or drain hose; less often, it's the pump, impeller…
24 March 2026 · 12 minutes read
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
If your microwave isn't heating but the light and turntable still work, the problem is usually one of the high-voltage components — the magnetron, diode…
15 February 2026 · 12 minutes read
If your refrigerator stops working, first check the outlet, the power cord, and the thermostat setting, and after defrosting let it stand for a while.
4 February 2026 · 12 minutes read












