experience10 yearsMaksim S.
Graphics card repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (775) 031 92 28Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Free diagnostics.
Our own technicians4 to 20 years of experience




Repair prices
Below are eight common symptoms and their likely causes. A technician will pinpoint the exact cause during free diagnostics.
no power, fuse, button
from3 500 ₸
dull blades, feed misalignment, debris
from8 500 ₸
jammed gearbox, worn brushes, break in circuit
from9 000 ₸
misaligned blades, loose mounting
from11 000 ₸
overload, worn blades, debris
from8 500 ₸
worn bearings, loose mounting
from6 500 ₸
sensor, overheating, jam
from7 000 ₸
natural wear, sparking, stoppage
from6 500 ₸
Select a service or symptom to see the price.
1 visittime
from 11,000 ₸cost

BeforeAfter5 steps

Five steps from request to performance check.
Describe the symptom and shredder model so the technician brings the right tools.
The technician arrives anywhere in the city within an hour of your request.
The technician identifies the parts needed and discusses the repair plan with you before starting.
You approve the scope of work and the price, then the technician begins the repair.
The technician cleans up debris and dust after the work so your workspace stays clean.
The computer and laptop repair department in Almaty has 7 technicians with 6 to 15 years of experience.

The department has 7 specializations — they are listed on the technicians' cards.
experience10 yearsGraphics card repair technician
experience6 yearsPC and laptop diagnostics technician
experience8 yearsLaptop repair engineer
experience10 yearsSoftware installation specialist
experience7 yearsPC and laptop repair technician
experience13 yearsDiagnostics and virus removal specialist
experience15 yearsConsultant
We reply during working hours
Fast technician visits across Almaty and free diagnostics help identify the cause of the shredder breakdown right away. Describe the symptom and model so the technician brings the right tools.

Warranty question? Call us
+7 (775) 031 92 287 898 reviews of repairs at TECH SERVICE in total
Лилия В.Order No. 504332 · 13 October 2026
oursПозвонил в три места, здесь единственные назвали цену сразу. Проблема — не режет. Уже полгода — ни одного сбоя.
Игорь Щ.Order No. 852316 · 10 April 2026
oursНужен был счёт и чек, у нас техника на балансе организации. В тех сервис привёл знакомый, у него тут чинили ноут. Пользуюсь ежедневно, вопросов нет.
Тимур И.Order No. ZK-1481 · 1 March 2026
oursПозвонил знакомому, он раньше работал в сервисе, посоветовал этих. Честно, уже готовился покупать новое, но обошлось. Основная жалоба — не режет. Роман Мигунов подсказал, как продлить жизнь технике. Разобрали, посмотрели: нож. Даже с учётом запчасти вышло гуманно. Всё оформили по договору, с печатью. Пользуюсь ежедневно, вопросов нет.
Марина В.Order No. TS-2602-636 · 18 February 2026
oursТехника на гарантии уже не была, так что выбор был свободный. Привёз на диагностику: шредер. С чем пришёл: заедает. В списке работ — нож. Прошивку не тронули, всё как было.
Аружан К.Order No. 32285 · 29 September 2025
oursБольше всего напрягало: заедает. Роман Мигунов помог выбрать, без навязывания. Вернули в тот же день, всё функционирует.
Гаухар Н.Order No. ZK-2430 · 18 September 2025
oursНужен был счёт и чек, у нас техника на балансе организации. Приехал из командировки, а дома — заедает. Договорились на утро, к девяти уже был свободный мастер. В списке работ — нож. Сделали и забыл про проблему.
Айнур М.Order No. ZK-3018 · 11 September 2025
oursПозвонил в три места, здесь единственные назвали цену сразу. Утром столкнулся с тем, что не режет. Назвали 31 500 сразу, в конце сумма не изменилась. Даже настройки не сбились, что удивительно.
Тимур И.Order No. ZK-2023/775 · 21 January 2023
oursБірінші рет осында жүгіндім, бұрын басқа жерге барғанмын. Рақмет, техника әлі күнге дейін жұмыс істеп тұр!!
Серик М.Order No. ZK-3597 · 29 January 2020
oursНужен был счёт и чек, у нас техника на балансе организации. Больше всего напрягало: не режет. Вернули в тот же день, всё функционирует.
Светлана Д.Order No. TS-3210 · 24 November 2019
oursС чем пришёл: заедает. Сергей Архипов приехал в тот же день, хотя был конец смены. Проверил дома — всё на месте, ничего не забыли.
Томирис Ж.Order No. 41650 · 20 November 2018
oursОтдельно спасибо мастеру — Сергей Москоленко, терпения ему хватило. Под замену пошло: двигатель. Сделали аккуратно, следов разборки не видно.
Гульмира С.Order No. 776022 · 24 February 2018
oursХотел сначала вызвать мастера на дом, потом передумал. Повод для визита: заедает. Ребёнок уже проверил на прочность, держится!!
Айгерим Б.Order No. TS-1808-790 · 10 February 2018
oursЦена имела значение, но и гарантия тоже. Поломка застала врасплох: не режет. Заодно поменяли: нож. Позвонил, описал проблему, сказали привозить — посмотрят в тот же день. Даже с учётом запчасти вышло гуманно. Чуть дольше, чем обещали, но предупредили. Прошивку не тронули, всё как было)
Диана М.Order No. TS-3179 · 7 March 2017
oursЦена имела значение, но и гарантия тоже. Диагностика шедера — с этого всё началось. Жалоба простая: заедает. Сергей Архипов принял, посмотрел и сразу сказал, что делать. Проверил дома — всё на месте, ничего не забыли)
Алишер У.Order No. TS-3296 · 4 August 2016
oursОсновная жалоба — заедает. Сергей Архипов всё объяснил и не пытался впарить лишнее. Все разъёмы на месте, ничего не люфтит.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionYes, a technician comes to your home or office anywhere in the city and handles most work on-site. We only take equipment to the service center for complex cases, such as replacing the motor or gearbox.
No, the approach is different: office models more often have issues with sensors, buttons, and the feed mechanism, while industrial ones put more load on the motor and cutting block. So the set of work and parts depends on the equipment class and model.
First, unplug it, switch to reverse, and remove any stuck sheets, and check for leftover staples. If jams keep happening after cleaning, the cause is in the blades or feed mechanism and it needs repair.
It's better not to use it: a burning smell and noise usually indicate motor overheating, worn brushes, or gearbox problems. Continuing to use it can lead to a more expensive breakdown, so it's best to unplug it right away.
Yes, we service office and industrial shredders of various brands, including Fellowes, taking into account the specific model's design. The technician identifies which component has failed and offers repair or replacement.
Repair makes sense if a sensor, button, or feed mechanism is worn out and the mechanical part is intact. If the motor or cutting block is seriously damaged on a cheap model, replacement may be more reasonable.
Tech Service repairs office and industrial shredders in Almaty: our technician comes to your home or office within 60 minutes or takes the equipment to our service center. Diagnostics are free, and we provide a 1-year warranty on labor and parts. Technicians with 4 to 20 years of experience identify the cause by symptom and fix it directly, without middlemen.
A shredder that's silent or hums without cutting involves different components. Let's break down what the technician checks first and why the symptom points to a specific part.
We start with the power supply and cable, then check the forward/reverse/auto buttons, and only after that the control board — this way we find the cause without unnecessary disassembly. In office models, power comes through an external adapter, and a voltage drop on it results in complete silence even when the electronics are fine. The button block suffers from dust and paper crumbs: contacts oxidize, and the auto switch stops closing the circuit. The control board fails less often — usually after a power surge, less commonly from moisture. If the device doesn't even respond with an indicator, it's more often the power supply rather than the electronics; replacing a cable or connector is simpler than restoring the board, so the technician checks the power first. We provide shredder repair in Almaty with on-site visits to your home or office, and diagnostics are free.
A hum without blade rotation almost always points to the gearbox and drive gears, or to a motor that receives power but doesn't transmit force to the cutting unit. In office models, a plastic or metal gearbox sits between the motor and blades: from overload and attempts to destroy a stack of sheets, the teeth strip, and the shaft spins idle. Metal gears withstand more, but if the blades jam, they can strip too. Less often the motor itself is at fault — the winding or brushes — then the motor hums but loses power. Continuing to turn on such a device is dangerous: the motor heats up under load, and instead of replacing a gear, you may need a more serious drive restoration. The technician opens the gearbox and checks the engagement before touching the electrics.
Running non-stop is usually related to the bin-full sensor or the control board, while a burning smell and loud noise point to thermal protection and motor overheating. The sensor is located at the bin entrance and sends a 'full' signal: if it's stuck or misaligned, the motor doesn't stop after a cycle and spins the blades idle. In this case, the control board doesn't execute the stop command, and the unit keeps running until protection kicks in. Thermal protection triggers based on the duty cycle — during continuous shredding longer than recommended, the winding heats up, and the protective element cuts power. If there's a burning smell, it's best to unplug the device immediately: repeated overheating of the motor leads to failure of a unit that could still have been restored.
A jam and 'not responding to paper' are often confused. Below is how a clogged cutting unit differs from a faulty paper sensor and what the technician does about it.
We determine the cause of a jam by the condition of the blades and reverse operation: if the cutting unit is clogged with staples, paper dust, the blades don't grab the sheet, and the shredder stops on every sheet. The anti-jam system runs the shafts backward, but with a dense clump of dust and staples, reverse doesn't clear the gap, and the stop repeats after one or two passes. During inspection, the technician disassembles the chamber, cleans it out, and checks how the shafts grab paper under load. Staples and paper clips that get into the cutting unit not only jam the sheet but also chip the blade edge — so after such an incident, not only cleaning but also a check of the cutting edge is needed. In our practice, jams after a stapler occur more often than any wear, and regular preventive cleaning of the cutting unit reduces the number of such calls.
If the shredder is on but doesn't start when you feed a sheet, we check the paper sensor first, then the control board — these are the parts that trigger the cutting mechanism. The sensor sits at the entrance to the feed slot and sends a signal to start the motor; when its window is clogged with paper dust, the machine doesn't see the sheet and stays silent even though the motor is fine. The technician checks the board second: looks at the signal at the input, tests the start circuit, and makes sure the command reaches the drive. The paper sensor often gets dirty with paper dust and stops detecting the sheet; simply cleaning the sensor gets the shredder working again without replacing parts. I recommend blowing out the slot with compressed air — that's cheaper than any replacement.
| Symptom | What we check first | Likely component |
|---|---|---|
| Won't turn on | Power and cable | Power supply, buttons |
| Hums but doesn't cut | Drive and gears | Gearbox, motor |
| Jams the sheet | Cutting mechanism and reverse | Blades, staples |
| Doesn't react to paper | Paper sensor | Sensor, board |
| Runs non-stop | Bin sensor | Sensor, board |
| Burning smell, noise | Thermal protection | Motor, overheating |
We repair shredders in Almaty in two ways: with a technician visiting your home or office, and at our service center. Below we explain what can be fixed on site and what requires the workshop.
We send our technician to your home or office within 60 minutes anywhere in the city, and the first thing they do is free diagnostics to identify the cause and cost of the work. Our technician checks the power, buttons, paper sensor, and reverse mechanism, so they can spot typical faults in office models from Fellowes, COMIX, and Bulros right on site. A visit is convenient when the equipment is in a meeting room or at a desk and you don't want to take it out of the office. On-site diagnostics benefit the client: if the problem is simple, the technician fixes it right away, and the machine doesn't have to be taken to the workshop. This format saves office employees time — the equipment gets back to work without trips or waiting.
On site we handle what doesn't require disassembling the drive or soldering the board, while complex work on the gearbox, motor, and electronics is done at the service center. During a visit, the technician replaces and cleans blades, clears jams, checks limit switches and the paper sensor, and restores contact in the power button — these operations take minimal time and don't require disassembling the drive. The control board, motor winding, and gearbox gears require soldering, testing, and disassembling the unit, so we take such equipment to the workshop. The technician decides after diagnostics, and the client knows in advance whether the machine will stay in the office or, if necessary, be taken to the service center. The second option takes more time, but complex components are checked at the workshop.
Buyers usually ask about warranty and diagnostics before booking a technician — these are the terms that shape the decision to repair. Below is what we cover and how payment for the work is handled.
We provide a 1-year warranty on labor and parts for shredder repairs, so if a component fails again due to our work, we'll fix it under warranty. This applies to both on-site service and in-shop repairs: the technician comes to your home or office, and if needed, takes the equipment to the workshop. Replaced parts — the gearbox, blades, control board, motor — are covered for the same period as the labor itself. In our experience, warranty cases most often involve repeated blade wear or a loosened component mount after intensive use. The parts warranty matters separately from the labor warranty: a replaced gearbox or blades are parts that should last their expected lifespan, not just the moment of installation. When you drop off your shredder, ask which components were replaced and exactly what the one-year coverage applies to — that way it's easier to make a claim if the symptom returns.
Diagnostics are free, and the technician quotes the cost of labor and parts after diagnostics — once the cause is known. Before disassembly, the technician checks the power supply, buttons, paper sensor, reverse function, and blade condition so they don't replace parts at random. A call-out within the city takes up to 60 minutes, and on site it becomes clear whether the shredder can be fixed at home or needs workshop repair. This way the client decides on repair knowing the exact cause, not a guess: sometimes after diagnostics it turns out that cleaning and lubrication are all that's needed. One more thing: don't agree to service until you're told the specific component and the nature of the fault — otherwise you're paying for a guess. The technician quotes the price after free diagnostics, so you have time to compare it with the cost of a new machine.
Office and industrial shredders break down differently: loads, components, and types of failure vary. Below is how the service approach differs for such equipment and which models and cut types we handle.
With office shredders, we most often deal with jammed blades, reverse wear, and paper sensor failures, because the equipment handles small sheets with frequent stops. A personal model and a departmental machine break down differently: the former wears out its cutting unit faster, while the latter wears out the drive and electronics designed for a steady flow of employees. Auto-feed shredders add a feed mechanism and a set of sensors that get knocked off by dust and fine debris. A separate story is repairing an office micro-cut shredder: the thin blade edges are sensitive to staples and clips, and the heavy paper flow in a large office accelerates shaft wear. An office shredder with auto-feed or micro-cut requires more careful cleaning of the cutting unit: fine debris clogs the mechanism faster than with strip-cut, and a clogged unit heats up and loses torque on the shaft.
Industrial shredders run under heavier loads, so we check the motor, gearbox, and cooling system—these are the components that suffer during continuous operation with large volumes of documents. Such a machine is designed for kilograms of paper per shift, and its weak point is not the cutting edge but the drive's ability to dissipate heat: a dust-clogged radiator and dried-out gearbox lubricant cause overheating long before the cutting parts wear out. Thermal protection then kicks in as a last line of defense, and frequent shutdowns are a signal to check the airflow and bearings, not to replace the blades. We approach industrial shredder restoration starting from the drive: first we assess how the motor handles the load and whether the gearbox jams under force. An industrial shredder can't be judged by office standards: motor overheating occurs differently here, and drive maintenance is more important than blade replacement.
| Shredder type | What breaks most often | What we look at during repair |
|---|---|---|
| Personal office | Blades, paper sensor | Cutting unit, reverse |
| Departmental office | Reverse, control board | Drive, electronics |
| Micro-cut | Cutting unit | Cleaning, lubrication, edge |
| Auto-feed | Feed mechanism | Sensors, drive |
| Industrial | Motor, gearbox | Cooling, thermal protection |
Not every breakdown is worth fixing. Below are the signs a technician uses to determine whether restoration will get the machine back to work, and when replacement is more reasonable.
Restoration makes sense when a single component has failed—blades, paper sensor, reverse, power supply—and the rest of the mechanisms are in working order. We start by checking the drive: if the motor and gearbox turn the shaft without jerking or unusual noise, the failure is local. Replacing the paper sensor or restoring the reverse function brings the machine back to normal operation, and after sharpening the blades cut as cleanly as before wear. The power supply is a separate story: voltage drop under load is fixed by replacing the module, and the electronics again handle the power on thick stacks. The motor doesn't overheat, and the shaft doesn't lose speed under a thick stapled block. If free diagnostics show that the motor and gearbox are intact, replacing one component returns the equipment to full operation, and there's no point in replacing the whole machine.
Replacement is smarter when several key components are damaged at once—motor, gearbox, and control board—or when the housing and cutting unit are worn so much that repair won't give a lasting result. A crack in the housing near the shaft means blade misalignment, and a burned-out control board often takes the motor with it: half the machine has to be replaced. Another sign is wear of the cutting unit to the point where sharpening no longer maintains the gap between blades, and the shredder crumples paper instead of cutting. Motor winding with signs of inter-turn short circuit and gearbox shaft play combined with blown electronics add up to a set where restoration doesn't pay off. The decision should be made after diagnostics, not by appearance: sometimes a "hopeless" machine is fixed by replacing one sensor, and sometimes it's cheaper to buy new equipment right away.
A shredder failure can almost always be identified by its symptoms, but an inspection confirms the exact cause. Below is a short summary to help you decide before the technician arrives.
11brands
Our technicians service shredders from various brands. See the list of brands with dedicated pages below.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your laptop screen is broken, turn the device off first, don't press on the display, and check the picture through an external monitor.
12 March 2026 · 11 minutes read
If your laptop freezes, the first thing to do is restart it and check Task Manager to see what's loading the CPU and memory.
25 January 2026 · 12 minutes read
If your computer won't turn on, start simple: check the outlet, power cable, switch on the power supply, and the power button.
19 January 2026 · 13 minutes read
If your laptop won't boot, first determine which of two states you're in: the device doesn't respond to the power button at all…
13 December 2025 · 12 minutes read












