Open until 19:00+7 (778) 746 00 26Call a technician
Tech Service technician next to a refrigerator

Beko Refrigerator Repair in Almaty

A technician arrives within 60 minutes anywhere in the city. Diagnostics are free.

  • Arrival within 60 minutes anywhere in the city
  • Free diagnostics
  • 1-year warranty

Our own technicians4 to 20 years of experience

Ruslan Ts.Dilmurat S.Nikita M.Damir M.

Repair prices

  • Diagnostics0 ₸
  • Drain line cleaningfrom5 000 ₸
  • Defrost timer / sensor replacementfrom6 000 ₸
  • Door rehanging / adjustmentfrom6 500 ₸
  • Door seal replacementfrom7 500 ₸
All prices
2ГИСЯours4,96 064 reviews
2GIS · Yandex · order database
Common faultsCommon faultsTECH SERVICE02

Common Beko refrigerator faults in Almaty

The symptoms Beko refrigerator owners most often report and their likely causes.

PricesPricesTECH SERVICE03

How much Beko refrigerator repair costs in Almaty

The Beko refrigerator repair table shows the starting labor price excluding parts and the turnaround time; the technician confirms the final total before any work begins.

Drain line cleaninglabour only

1–2 hours

from5 000 ₸

Defrost timer / sensor replacementparts not included

1–2 hours

from6 000 ₸

Door rehanging / adjustmentlabour only

1–2 hours

from6 500 ₸

Door seal replacementparts not included

1–2 hours

from7 500 ₸

Filter drier replacementrefrigerant not included

1–2 hours

from7 500 ₸

Before and afterBefore and afterTECH SERVICE04

Before and after Beko refrigerator repair in Almaty

Not holding temperature due to thermostat

1 visittime

from 9 500 ₸cost

Problem
The Beko refrigerator stopped holding temperature: the compressor either would not turn on or ran without stopping; the thermostat is faulty.
What we did
The technician opened the thermostat housing in the chamber, replaced the thermostat and connected the wires, and checked the compressor turning on and off.
Result
The refrigerator holds temperature again; the compressor turns on and off as it should. 1-year warranty on labor and parts.
I want the same
In a kitchen with light gray fronts, a white refrigerator with glass shelves is open; a technician in an orange shirt holds a thermostat with wires near the open thermostat housing inside the compartment.BeforeAfter
01 / 05
All repairs
TECH SERVICE mobile technician with a tool case

How Beko refrigerator repair works at your home in Almaty

Five steps from request to checking the work after repair.

  1. Requeston the day of request

    Submit a request, describe the symptom and your Beko refrigerator model.

  2. Technician visitwithin 60 minutes

    The technician comes anywhere in the city to inspect the appliance on site.

  3. Inspection and diagnosticson site

    The technician checks the compressor, thermostat and seals to find the cause.

  4. Approval of workafter inspection

    You approve the scope of work and parts, then the technician starts the repair.

  5. Check with the technicianafter repair

    Ask the technician about the warranty terms and what to do if the symptom returns.

Leave a request
TechniciansTechniciansTECH SERVICE05

Our Beko refrigerator repair technicians in Almaty

The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

  • 8 technicians in Almaty
  • 8–12 years of experience in the department
  • Article author Ruslan Ts., 9 years of experience
Technician repairing a refrigerator at a customer’s home
Field technician at a customer’s home

The department has 8 specializations — they are listed on the technicians' cards.

01 / 05
Ruslan Ts., washing machine and refrigerator repair technicianexperience9 years

Ruslan Ts.

Washing machine and refrigerator repair technician

Dilmurat S., field technician for washing machine and refrigerator repairexperience10 years

Dilmurat S.

Field technician for washing machine and refrigerator repair

Nikita M., field refrigerator repair technicianexperience8 years

Nikita M.

Field refrigerator repair technician

Damir M., general household appliance repair technicianexperience12 years

Damir M.

General household appliance repair technician

Dima, expert washing machine repair technicianexperience8 years

Dima

Expert washing machine repair technician

We reply during working hours

Book Beko refrigerator repair in Almaty

In your request, specify a convenient visit time and a contact number so the technician can confirm the arrival.

TECH SERVICE administrator replying to a customer's WhatsApp message

Warranty question? Call us

+7 (778) 746 00 26
Customer reviewsReviewsTECH SERVICE06

Reviews of Beko refrigerator repair in Almaty

Асель Ж.Order No. 2026-4630 · 5 February 2026

ours

Долго искал, кому это отдать, и вот нашёл. Повод для визита: намерзает лёд. Никита М объяснил причину так, что понял даже я. Сказали 32 500, я согласился без торга. Диагностику сделали бесплатно, хотя я был готов платить. В списке работ — уплотнитель. Рекомендую. Проверили при мне, показали, что всё держит

Repair: refrigerator

Алексей Г.Order No. TS-2501-114 · 4 August 2025

ours

Работаю допоздна, поэтому нужен был сервис с нормальным графиком. По деньгам вышло адекватно, в другом месте просили больше. Уже полгода — ни одного сбоя)

Repair: refrigerator

Мадина Т.Order No. TS-7219 · 28 November 2024

ours

Хотел сначала вызвать мастера на дом, потом передумал. Нужен был ремонт холодильника — обратился сюда. С чем пришёл: шумит. Сказали 27 000, а потом ещё и скидку сделали. Приехал вечером, мастер ещё был на месте. Заодно поменяли: термостат. В помещении тесновато, но это мелочи. Внешне как новый, если не считать мелкой царапины!!

Repair: refrigerator

Лилия В.Order No. TS-4770 · 30 May 2024

ours

Работаю допоздна, поэтому нужен был сервис с нормальным графиком. Основная жалоба — намерзает лёд. Проверили при мне, показали, что всё держит.

Repair: refrigerator

Сергей Р.Order No. 598321 · 25 April 2020

ours

Выбирал по отзывам в 2ГИС, времени на эксперименты не было. До последнего откладывал, но пришлось признать: шумит. Могли бы взять больше, но взяли по-божески. Заявку приняли по телефону, перезвонили через десять минут. Деталь на замену — уплотнитель. Пять звёзд, не задумываясь. Ребёнок уже проверил на прочность, держится.

Repair: refrigerator

Светлана Д.Order No. ZK-2019/136 · 30 May 2019

ours

Было подозрение, что дело в плате, хотелось услышать второе мнение. Честно, уже готовился покупать новое, но обошлось. Проблема — шумит. Проверил дома — всё на месте, ничего не забыли.

Repair: refrigerator

Аяна Е.Order No. 25364 · 9 December 2017

ours

Отдал мастеру: холодильник. Жалоба простая: шумит. Никита М объяснил причину так, что понял даже я. Смета совпала с итогом, что редкость. Поставили новую деталь: термостат. Мастер сразу сказал, что к чему, без размытых формулировок. Нагрев в норме, посторонних звуков нет.

Repair: refrigerator

Станислав К.Order No. TS-3337 · 28 February 2017

ours

Повод для визита: шумит. Дильмурат С всё объяснил и не пытался впарить лишнее. Уже полгода — ни одного сбоя.

Repair: refrigerator

Акбота Т.Order No. ZK-2520 · 13 April 2016

ours

Проблема — шумит. Никита М подсказал, как продлить жизнь технике. Починили и дали гарантию на месяц.

Repair: refrigerator

Сергей Р.Order No. ZK-8150 · 20 March 2016

ours

Хотел сначала вызвать мастера на дом, потом передумал. Нужен был ремонт холодильника — обратился сюда. Основная жалоба — шумит. Всё оформили по договору, с печатью. Заодно поменяли: термостат. Вышло 34 500 тенге, дешевле, чем я рассчитывал. Однозначно да. Проверил дома — всё на месте, ничего не забыли.

Repair: refrigerator
See all reviews
Questions and answersQuestionsTECH SERVICE07

Questions about Beko refrigerator repair in Almaty

Didn’t find the answer? Message us on WhatsApp.

Ask a question
Who makes Beko refrigerators and where are they assembled?

Beko is a brand of the Turkish holding Arçelik, with production set up at several plants. Check the country of assembly for your model on the label inside the compartment or on the back panel.

How do I find the model of my Beko refrigerator to match a part?

The sticker with the model and serial number is usually on the side wall of the fridge compartment or on the back of the unit. The technician uses this information to select compatible parts; the set depends on the model.

Is it dangerous to leave a Beko refrigerator plugged in if it clicks and won't start?

Yes, it's best to unplug it right away. Clicking often comes from the start relay or compressor, and if the appliance keeps running, the unit can be damaged beyond repair.

Is there a warranty on compressor replacement for a Beko refrigerator?

Yes, we provide a 1-year warranty on labor and parts. The technician will explain after the repair what exactly is covered in your case; it depends on the model.

Can a Beko No Frost refrigerator be repaired at home in Almaty?

Most No Frost failures — fan, sensors, defrost, refrigerant leak — we fix right at your home. We only take the appliance to the service center when a complex unit repair is needed.

Can an inverter compressor in a Beko refrigerator be repaired separately from the electronics?

It depends on the model and the nature of the fault: sometimes the issue is in the board or sensors, and the compressor itself is fine. The technician will determine what exactly failed after free diagnostics.

Repair guideArticleTECH SERVICE08

Beko Refrigerator Repair in Almaty by a Direct Contractor

Ruslan Ts., washing machine and refrigerator repair technician

Author: Ruslan Ts.,Washing machine and refrigerator repair technician

Published
Updated

Tech Service repairs Beko refrigerators in Almaty at your home and in our service center: our own refrigerator technician with 4 to 20 years of experience arrives within 60 minutes anywhere in the city. Diagnostics are free, the technician gives you the price after diagnostics, and we provide a 1-year warranty on labor and parts.

Why Your Beko Refrigerator Isn't Cooling and What the Error Codes Mean

Beko signals a fault in different ways — a code on the display, how the motor behaves, or frost buildup in the compartment. Let's break down what each signal means and which component is behind it.

What Error E1 and Other Codes on the Beko Display Mean

The E1 code on a Beko display most often points to a faulty temperature sensor in the refrigerator compartment, and that's exactly where we start diagnostics. Then, following the manufacturer's code table, we check defrost circuit errors, evaporator sensor errors, and communication with the control board: each has its own place in the low-voltage section. On the Beko board, the thermistors share a common connector, so an oxidized contact can produce the same code as a failed component. We check the sensor's resistance with a multimeter, test the wiring harness to the board, and only then make a call on the component. A code isn't a death sentence for a part — it points to a circuit: often the culprit is a contact or the board itself, so replacing a part based on a single code blindly isn't worth it. If decoding the code doesn't give an answer, Beko refrigerator repair in Almaty starts with a full diagnostics of all circuits.

Beko Refrigerator Not Cooling but the Light Is On

If the light inside is on but there's no cold, on a Beko the most common culprits are the motor-compressor, the start-protection relay, or a refrigerant leak — we check all three one by one. We remove the relay and test it separately for starting: burnt contacts cause a click without the shaft turning. Then we measure current draw and pressure in the circuit — that's how a leak is distinguished from mechanical wear of the unit. A motor that sounds like it's running doesn't mean it's working: with a refrigerant leak it hums idly, and cooling fades gradually over several days. Listening isn't enough — you need measurements and a circuit check, otherwise replacing the relay won't bring the cold back, it'll just delay another call. In practice, we first test the windings and only then connect the manifold gauge.

Clicking, Humming, Frosting, or Shocking — Beko Symptom Table

SymptomProbable CauseBeko Component
Clicks and won't startstart mechanism not engagingstart-protection relay, compressor
Hums loudlyworn mounts or motorcompressor
Frost and ice buildupdefrost failuredefrost heater, sensor, No Frost fan
Doesn't shut off, overcoolssticking thermostatthermostat
Water at the bottom, odorclogged draindrain channel
Shocksinsulation breakdownpower cord, compressor

How Beko No Frost Failures Differ from Cycle Defrost Models

Beko has two defrost systems, and they fail in different ways. Knowing your model's type helps you anticipate the component and not be surprised why the technician checks the fan or drain first.

What Breaks on Beko No Frost Refrigerators

In Beko No Frost refrigerators, the most common failures are the evaporator fan, the defrost heater, or the sensor, which causes ice to build up on the back wall of the freezer. The fan circulates cold air through the compartments, the heating element periodically melts frost on the evaporator, and the thermistor tells the controller when to start this cycle. If the defrost circuit malfunctions, the evaporator becomes covered in ice, airflow stops, and both compartments warm up even though the compressor appears to be running. Our technicians first check the heater's resistance and the thermistor readings, then the fan rotation and blade movement. In such cases, Beko refrigerator repair at home begins with diagnosing the defrost circuit. Ice in a No Frost system is almost always a result of a defrost cycle failure, not a reason to manually defrost: manual defrosting will remove the symptom, but the faulty component remains, and ice will return within a few days.

Common breakdowns of drip-type Beko refrigerators

In drip-type Beko refrigerators, moisture drains down the back wall into the drain, so typical issues involve a clogged drain, the thermostat, and the door seal. The back wall of the refrigerator compartment periodically gets covered with condensation, and droplets flow down to the drain hole and evaporate there. When the channel gets clogged with crumbs and slime, water doesn't drain and collects at the bottom of the compartment, and if the clog is severe, it leaks under the vegetable drawers. A thermostat with burnt contacts stops turning off the compressor, and food in the refrigerator compartment freezes near the back wall. A worn door seal lets warm air in, and the wall gets covered with a thick layer of frost. If there's water at the bottom of a drip-type Beko, it's usually a clogged drain channel rather than a "broken cooling system" — cleaning it with a flexible wire solves the problem without replacing parts.

Comparison of Beko by defrost systems

ParameterBeko No FrostBeko drip-type
Moisture removalby air, through defrostdown the back wall into the drain
Common failuresfan, heating element, sensordrain, thermostat, door seal
Sign of failureice in the freezerwater at the bottom, frost on the wall
What we check firstdefrost circuitdrain channel

How Beko refrigerator repair at home works

We fix most Beko breakdowns right at your home. Here's the step-by-step process our technician follows, which components he checks, and when a visit to the service center is still necessary.

Step-by-step Beko repair at home

  • Diagnostics: a free inspection where the technician identifies the faulty component, checks the thermostat, relay, and compressor windings, and explains the cause of the breakdown.
  • Approval: the technician quotes the cost of labor and parts and waits for your decision — he doesn't start work until you agree.
  • Repair: he replaces the relay, board, fan, or fixes a refrigerant leak in the circuit, selecting parts for your specific model.
  • Check: he makes sure the refrigerator cools, maintains the set temperature, and reaches operating mode without the compressor stopping.
  • Warranty: we provide a 1-year warranty on labor and parts.

How refrigerant leaks are found and when recharging is needed

We trace the refrigerant leak in Beko refrigerators along the circuit: we check the connections, capillary tube, and filter-drier, then recharge the system. A pressure gauge shows the pressure in the circuit, which indicates whether the system holds tight after soldering. We replace the filter-drier every time the system is opened: the old one absorbs moisture and clogs the capillary, causing the compressor to run overloaded and overheat. Owners know the signs of a leak: the fridge hums nonstop, there's no frost on the walls, and food in the main compartment warms up even though the light is on. Just "topping up" without finding the leak is pointless—the refrigerant will escape again through the same spot, so we always find and fix the cause first, and recharge only after restoring the circuit. We perform such Beko refrigerator repair in Almaty on-site so you don't have to transport the appliance to a service center.

What we fix on-site and what in the workshop

On-site for Beko we replace relays, fans, thermostats, control boards, and fix leaks, while complex work on the circuit and compressor is sometimes moved to the workshop. Replacing a compressor requires soldering the circuit under pressure and vacuuming the system—this is inconvenient and unsafe in an apartment, so such work is better done in the workshop. Repairing the control board on-site is possible if the fault is local; with extensive damage, the board is replaced entirely. A technician arrives within 60 minutes anywhere in the city, so you get on-site diagnostics without a long wait. Honestly saying "this needs the workshop" is better than fixing blindly on-site: some jobs require conditions that an apartment can't provide, and the result depends on it.

What to check yourself before the technician arrives

While the technician is on the way, you can rule out some causes yourself—and also protect yourself from unnecessary risks. Here's a list of checks that won't do any harm, and one condition when you should immediately unplug the appliance.

Simple checks that won't do any harm

  • Power: make sure the plug is firmly in the socket and the circuit breaker in the panel hasn't tripped.
  • Thermostat: check that the knob isn't turned to minimum—at that setting the fridge won't get cold.
  • Door: inspect the seal for gaps, cracks, and tightness around the perimeter.
  • Ice buildup: note where ice forms—on the back wall, in the corners, or on the evaporator.
  • Smell and water: check for a puddle at the bottom of the compartment and any unusual odor.
  • Power cord: trace it along its length to where it enters the body—kinks and melted spots are noticeable.

When a Beko refrigerator gives you an electric shock

If a Beko gives you an electric shock, unplug it immediately and don't turn it on until the technician arrives—this is a sign of insulation breakdown. A noticeable shock from the body is not "static electricity": most often the compressor insulation is broken or the power cord is damaged at the plug or where it enters the body. Also rule out an ungrounded outlet—common in older apartment buildings in Almaty, where potential builds up on metal parts. The danger is that the breakdown progresses gradually: first a tingle with wet hands, then a noticeable shock. Don't use the appliance until the cause is fixed and don't try to test the wiring yourself: without disassembling the circuit, you can't check the compressor start or relay anyway. Pull the plug from the outlet and leave the doors slightly open—this way the compartment won't get moldy while you wait for the technician. If diagnostics show a unit needs replacement, owners often ask how much a new model costs—but the exact repair price is only given after inspection.

How to choose a Beko technician and the terms we work on

People look for a Beko specialist based on one thing—whether they know the brand and stand behind the result. Here's how to tell a direct contractor and the terms we work on.

How to tell that a technician knows Beko

A technician who knows Beko will decode the display code on the spot, ask about the defrost system, and name the likely component before even arriving. Beko refrigerators are built on different platforms: No Frost models have their own weak spots — defrost, fan, sensors — while drip models have others — thermostat and drainage. A refrigeration technician with 4 to 20 years of experience usually keeps both scenarios in mind and can tell a sensor fault from a refrigerant leak just from the symptoms. They will also ask which code is showing on the panel instead of asking you to 'photograph everything.' If the technician answers a question about error E1 or the difference between No Frost and drip models with vague generalities, chances are they handle any brand without specialization — and will start replacing parts at random.

Why a direct contractor is better than an intermediary

Tech Service is a direct contractor: our own specialist comes to your home, not an intermediary who passes the request to a third party. In the chain 'dispatcher — subcontractor — technician,' responsibility gets blurred: one takes the request, another does the repair, and a third promises the warranty. With us, the person who ran the diagnostics and fixed the problem is the same one accountable for the result, and the 1-year warranty on labor and parts comes from the person who held the tools. For the owner, this means that if the issue recurs, you don't have to explain the whole history to a stranger — just describe what happened to the same employee. We provide home visits throughout the city, so there's simply no need for a middleman: the same party takes the request and closes it.

Warranty, diagnostics, and booking a technician

Diagnostics are free, a specialist arrives within 60 minutes anywhere in the city, and we provide a 1-year warranty on labor and parts. You can book a visit to any address — apartment, house, or office; the Beko service center only stands in for the visit, but the repair is done on site. You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies. The specialist gives you the price after the free diagnostics — until then you pay nothing for the inspection and are not obligated to proceed with the repair. A common question is how much a Beko refrigerator itself costs: the price on the secondary market depends on condition, but repair is almost always cheaper than replacement, especially if the fault is local — a sensor, thermostat, or start relay. If after the inspection that option doesn't work for you, you simply decline, and the inspection remains free.

When a Beko refrigerator repair pays off

Here's the key information about Beko refrigerator breakdowns — from decoding display codes to choosing a technician. Below are brief takeaways to help you decide on servicing your appliance.

  • A code on the display is not a verdict: the error points to a circuit, not always to a specific part, so replacing components at random without diagnostics makes no sense.
  • The defrost system matters: No Frost and drip Beko models have different typical failures, and the technician should clarify the type before visiting.
  • Most work is done at home: complex cases involving the refrigerant circuit sometimes require a workshop, but the rest is fixed on site.
  • Before the technician arrives: check the power supply, thermostat, and door seal, and if you get an electric shock, unplug the appliance immediately.
  • Choose a direct contractor: a question about Beko codes and the defrost system will immediately reveal their qualification.

90brands

Besides Beko, we repair other refrigerator brands in Almaty

We work with every brand sold in Kazakhstan — from Samsung, LG and Atlant to Biryusa, Indesit, Stinol and rare imported makes. Can’t find yours in the list? Call anyway — a technician will come and take a look.

We also repairWe also repairTECH SERVICE09

Besides Beko refrigerator repair, we fix other equipment in Almaty

Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.

BlogBlogTECH SERVICE10

Worth reading before Beko refrigerator repair in Almaty

Leave a review

Choose a platform — the TECH SERVICE page will open.

2ГИС2GISЯYandex Maps
Send a review with photos on WhatsApp