experience9 yearsRuslan Ts.
Washing machine and refrigerator repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (775) 031 92 28Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
We bring back the shape and shine of your jewelry. 1-year warranty on labor and parts, and a jeweler arrives within 60 minutes anywhere in the city.
Our own technicians4 to 20 years of experience




Repair prices
Below are typical jewelry problems and their likely causes. The jeweler confirms the exact cause after diagnostics.
Metal fatigue and a thin band
from8 000 ₸
Stretched links, twisting, defect
from4 000 ₸
Worn spring and a loose fitting
from1 500 ₸
Seasonal swelling and finger size changes
from8 500 ₸
Loose prong, impact, worn setting
from4 000 ₸
Oxidation and contact with chemicals
from2 500 ₸
Abrasion of the coating and contact with water
from9 500 ₸
Thin post and mechanical pressure
from15 500 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1–2 hourstime
from 4,000 ₸cost

BeforeAfter5 steps

Five steps from your request to checking the finished piece.
Leave a request, and the jeweler will agree on a convenient time for the visit.
The jeweler confirms the address and a convenient time window so you don't have to wait.
After confirmation, the jeweler arrives anywhere in the city within 60 minutes.
You approve the scope of work and the price, and then the jeweler starts the repair.
Check the result together with the jeweler.
The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience12 yearsGeneral household appliance repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsExpert washing machine repair technician
experience8 yearsField refrigerator repair technician
experience8 yearsSenior washing machine repair technician
experience11 yearsDishwasher repair technician
experience9 yearsWashing machine repair technician
We reply during working hours
Leave a request and tell us the type of piece, the metal and its hallmark, and what happened to it, so the jeweler understands the task in advance. 1-year warranty on labor and parts.

Warranty question? Call us
+7 (775) 031 92 287 898 reviews of repairs at TECH SERVICE in total
Алишер У.Order No. 26741 · 26 October 2026
oursСервис нашёл случайно, но остался доволен. Искал мастерскую поближе к дому, чтобы не мотатся с техникой через полгорода. Могу рекомендовать)
Фарида К.Order No. TS-2604-153 · 8 April 2026
oursНужен был ремонт, искал вариант поближе. Мастер посмотрел, назвал причину, всё разложил по полочкам. Приняли быстро, объяснили, что и как будет. Проверили при мне, показали результат. Всё объяснили простыми словами. Цену сказали сразу, без «ну потом посмотрим». Запчасть нашли без проблем. Рекомендую.
Наталья С.Order No. 2025-5951 · 13 June 2025
oursНашёл по отзывам, решил попробовать. Было подозрение, что дело в плате, хотелось услышать второе мнение. Пять звёзд, не задумываясь
Павел Ш.Order No. TS-1640 · 16 November 2022
oursИскал сервис с гарантией, чтобы не переделывать. Искал мастерскую поближе к дому, чтобы не мотаться с техникой через полгорода. Дамир М подсказал, как продлить жизнь технике!!
Марат Ж.Order No. 74495 · 3 September 2020
oursДолго откладывал, но пришлось обратиться. Достойно. Запчасть нашли без проблем.
Фарида К.Order No. ZK-2019/356 · 4 February 2019
oursВыбирал между несколькими сервисами, остановился на этом. Было важно, чтобы сделали до выходных — гости, то-сё. Дамир М помог выбрать, без навязывания. Не пришлось ничего доказывать и просить. Не пожалел ни разу.
Айгуль К.Order No. 17745 · 19 December 2018
oursНашёл по отзывам, решил попробовать. Дамир М честно сказал, что менять, а что ещё походит. Однозначно да
Гульнара Б.Order No. 355441 · 6 April 2018
oursСервис нашёл случайно, но остался доволен. Позвонил в три места, здесь единственные назвали цену сразу. Проверили при мне, показали результат. Мастер посмотрел, назвал причину, всё разложил по полочкам. Однозначно да.
Татьяна Б.Order No. 646537 · 17 February 2017
oursБыла срочная поломка, нужен был мастер сегодня. Цена имела значение, но и гарантия тоже. Сначала перепутали модель, потом исправились.
Фарида К.Order No. ZK-2016/997 · 14 July 2016
oursОбращаюсь не первый раз, поэтому есть что сказать. Выбирал по отзывам в 2ГИС, времени на эксперименты не было. Чуть дольше, чем обещали, но предупредили. Сделали ровно то, о чём договаривались. Дали гарантию и рекомендации на будущее. Цену сказали сразу, без «ну потом посмотрим». Не пришлось ничего доказывать и просить. Буду советовать знакомым
Didn’t find the answer? Message us on WhatsApp.
Ask a questionYes, a technician comes to your home anywhere in the city within 60 minutes of your request. On site, they diagnose the piece free of charge and agree on the work, while complex repairs are done at the service center.
Yes, with careful soldering the break is barely visible, especially on thin chains. The technician selects solder that matches the metal's purity and polishes the seam, but the result depends on the weave and the thickness of the link.
Usually 2–3 adjustments are fine; after that the metal thins and weakens from the heat. The technician will assess the shank during the jewelry repair and tell you whether another resize is worth doing.
With a proper resize, the stone settings are preserved, but after the adjustment the technician checks every setting. Sometimes during jewelry repair the prongs are tightened or replaced so the stone stays secure.
A laser heats precisely and doesn't burn through a thin link, so the seam is neater and stronger. A torch is simpler for heavy pieces, but on a thin chain during jewelry repair there's a higher risk of deformation.
Yes, the absence of a hallmark doesn't prevent repair: the technician will identify the metal on site and choose the right solder. It's worth mentioning this in advance so they can prepare properly for working with the piece.
Jewelry repair in Almaty at Tech Service is handled by our own jewelers with 4 to 20 years of experience: they solder chains, resize rings, set stones, and restore clasps and plating. Diagnostics are free, a jeweler arrives within 60 minutes anywhere in the city, and there is a 1-year warranty on labor and parts.
Rings are restored by soldering, reshaping the band and resetting stones, and the method depends on where the damage is and what it looks like. Here are three common situations that bring a ring to a jeweler.
We solder a crack in the band if the metal around it has kept its thickness, and we replace a worn-thin section with an insert of the same alloy. The band is the lower part of the ring that takes the load every time you clench your hand, so cracks appear there more often than near the setting. A jeweler with 4 to 20 years of experience examines the damage under a loupe, checking its depth, direction and any old seams nearby. For 585 gold, the solder is matched to the same shade so the joint doesn't stand out after polishing. When the metal has worn almost paper-thin, solder won't hold for long, and an honest answer is a new section. Jewelry repair in Almaty with us starts with free diagnostics, so you decide on the method already knowing the condition of the ring. A thin dark line on the inside of the band is a reason to show the ring to a jeweler before it breaks completely.
We resize a ring by stretching it one or two sizes, and for a bigger change we add an extra section of metal or remove some. When stretched, the metal gradually expands and the band becomes slightly thinner, which is noticeable on delicate rings. Sizing down is done by removing a section and soldering, after which the seam is smoothed and polished to an even shine. Wedding bands with an engraving inside are resized carefully so the inscription stays out of the seam area. Rings with stones set all the way around cannot be stretched, because the settings would spread and the stones would start falling out. Such pieces are resized only on a section without stones, if there is one, and with a full eternity row we say honestly that resizing is risky. Before ordering, try the ring on in the evening when your fingers are slightly swollen, so the new size won't feel tight in hot weather.
Chains and bracelets are restored by soldering a link, replacing the clasp or straightening the weave, depending on where the piece gave way under load. They usually break near the clasp, at a thin link or at a bend.
We solder a broken link with solder of the same hallmark, so after polishing the joint matches the color of the rest of the chain. Before soldering, the jeweler looks at why the link failed: thin metal, an old seam nearby, or a sharp tug when the chain caught on clothing. If the links next to the break have also thinned, they are replaced together, otherwise the chain will snap at the neighboring spot. With hollow chains, the heat is chosen with special care, because the link wall is thin and overheating burns right through it. Bracelets with large links are soldered the same way, but the link is also straightened so the bracelet lies flat on the wrist. Put all the pieces of the chain in a separate bag, because even one lost link changes the length and has to be replaced with new metal.
| Clasp | Typical problem | What is done |
|---|---|---|
| Lobster clasp | Lever spring has weakened | Spring or whole clasp replaced |
| Spring ring | Ring no longer snaps shut | Replaced with a same-size clasp |
| Box clasp | Tongue loosened, clasp opens | Tongue bent back, case straightened |
| Hook clasp | Bent open, chain slips off | Hook straightened and tightened |
| Magnetic clasp | Weak magnet, housing came loose | New clasp fitted |
We untwist a kinked chain and tighten stretched links, as long as the metal in them hasn't worn down to a thin wire. Twisting happens when a chain is stored tangled in a jewelry box, and stretching comes from a heavy pendant constantly pulling on a thin weave. Anchor and curb chains take straightening well, because their round or flat links return to shape without marks. Dense weaves like snake and rhombus chains rarely recover without a trace after a kink, and a visible crease stays at the bend. In such cases, the jeweler suggests cutting out the damaged section and soldering the ends, though the chain becomes slightly shorter. The decision is yours after the inspection: for some people length matters more, for others a smooth look. A thin chain with a heavy pendant is best taken off at night, because the weave twists and stretches most during sleep.
Earrings and pendants are repaired precisely, by straightening the ear wire, replacing the backing or rebuilding the bail, while costume jewelry is restored with its alloy and glued stones in mind. Their weak points are small, but they break often.
We straighten a bent ear wire and replace a broken lever-back clasp or a stud backing with a new one made of the same metal. Ear wires bend when earrings are put on in a hurry or worn in bed, especially thin hoops, and after two or three bends the metal at the fold gets tired. A lever-back clasp breaks at the hinge: the spring weakens and the earring opens on its own. Studs lose their backings, and a new one is matched to the post diameter so it holds tightly. When you need urgent jewelry repair before an important event, the jeweler will tell you during diagnostics what can be done on the spot and what requires soldering at the service. Don't keep an earring with a bent ear wire in your ear, because metal bent again breaks at the same place, and then the wire has to be soldered back on.
A pendant bail wears down from rubbing against the chain, so it is rebuilt or replaced before the pendant falls off and gets lost. The friction never stops: the pendant swings with every step, and the metal of the bail and the chain wear each other away. Thin bails on silver pendants wear fastest, because silver is softer than 585 gold. A new bail is made from an alloy of the same color and soldered so the heat doesn't reach a stone or enamel on the front. Sometimes it makes sense to fit an opening loop, so the pendant can be moved to another chain without soldering. On a necklace with several pendants, all the jump rings are checked, because they wear out at about the same time. If the bail has become thinner than the chain links, it's time to see a jeweler, since from then on the metal wears faster and the break usually happens outdoors.
Metal and plating change the approach to the work, because the solder, heating and finishing depend on the hallmark and hardness. The same damage on gold and on silver is fixed in different ways.
| Metal | Properties | What the work takes into account |
|---|---|---|
| 585 gold | Hard, holds its shape well | Solder matched to alloy color |
| 750 gold | Softer, richer in color | Gentle reshaping without extra stress |
| White gold | Coated with a rhodium layer | Rhodium replating after soldering |
| 925 silver | Soft, tarnishes over time | Careful heating, tarnish removal |
| Gold-plated silver | Thin gold layer on top | Plating restored after the work |
| Unmarked metal | Unknown composition | Inspection and testing first |
Silver tarnishes from sulfur compounds in the air, in cosmetics and on the skin, and we remove the tarnish by cleaning followed by polishing. The rate of tarnishing differs from person to person, depending on sweat composition, creams, medications and even rubber in a jewelry box. 925 silver contains copper, which oxidizes together with the silver, so the tarnish can be not only dark but also greenish. The jeweler removes it with gentle compounds that don't wear away the metal, and then polishes the surface back to its original shine. Blackened patterns are not touched during cleaning but worked around, otherwise the design that made the piece special would disappear along with the tarnish. Home methods with baking soda and toothpaste scratch silver, so with heavy tarnish free diagnostics from a jeweler make more sense than kitchen experiments.
We reapply worn gold plating and rhodium after repair, because soldering and polishing remove a thin layer of coating from the treated area. Rhodium is a platinum-group metal used on white gold for a cool shine and scratch protection. Over time the rhodium layer wears off on raised areas, and the yellowish tone of the alloy shows through. Gold plating on silver behaves the same way, disappearing first on ring edges and clasps. Enamel needs a different kind of care, since it fears heat and cracks if soldering is done nearby. That is why the jeweler shields the enamel area from the flame or chooses a cold joining method. Before repairing a plated piece, ask whether the coating will need restoring after soldering, because without it the repaired spot on white gold will look noticeably yellower than the rest of the jewelry.
The cost is made up of the type of work, the metal and the number of operations, and the process runs from free diagnostics to checking the finished piece. Here is what affects the amount and what happens after you leave a request.
The jeweler names the cost after free diagnostics, once the metal, the damaged spot and the number of operations are clear. Three things affect the total: the type of work, the hallmark and whether there are stones. Soldering a link on a chain without stones is one operation, while resizing a ring with a row of stones involves reshaping, soldering, setting and polishing. White gold adds rhodium plating, and gold-plated silver adds restoring the coating. If a new part is needed, such as a clasp or a stud backing, its cost is added to the work. We discuss jewelry repair prices in Almaty before any work begins: the jeweler names the amount, and you decide calmly whether to go ahead. A piece with several problems is better shown whole than brought in bit by bit, so the jeweler sees all the damage at once and offers one plan.
Our jeweler arrives within 60 minutes anywhere in the city, inspects the piece on site, and does any work that needs heat at the service. Tech Service is a direct provider: our own jeweler comes to you, not a middleman who passes your jewelry on. During the visit, the jeweler runs free diagnostics, shows the damage under a loupe and explains which operations are needed. Small tasks like straightening an ear wire or bending a prong back are sometimes done on the spot if no heat is required. Soldering, resizing and restoring plating need a flame and polishing, so the jeweler does that work at the service. You can also bring the jewelry to the service yourself, and diagnostics there are free as well. Before the jeweler arrives, lay the piece on a light cloth by a window, because cracks and worn prongs are easier to see in daylight.
Proper storage, taking jewelry off before strain and regular inspections by a jeweler help it last longer. These habits remove the reasons the piece broke the first time.
Rings and chains should come off before sports, cleaning with household chemicals, swimming pools, saunas and sleep. During a workout a ring gets squeezed between the palm and a dumbbell handle, so the band deforms and the prongs catch on gloves and spread. Chlorine in pools and cleaning products reacts with the copper and silver in the alloy, the metal becomes brittle, and old soldered joints weaken first. In a sauna gold heats up and can burn the skin, and sudden temperature changes harm stones like emeralds. During sleep a chain twists and hoop earrings bend against the pillow. Hand cream goes on before putting rings on, otherwise it clogs the space under the stones and dulls the shine. If a piece breaks again in the same place, think back to when it happened, because the cause often turns out to be the same habit rather than the quality of the soldering.
We recommend showing jewelry with stones to a jeweler once a year to catch loose prongs and worn clasps in time. A wedding band that is never taken off wears evenly, and a thinning band can only be seen during an inspection. A chain with a pendant is worth checking as soon as the bail starts to wear noticeably. Many people look for jewelry repair near me only after losing a stone, although tightening prongs in advance costs less than finding a new stone. Diagnostics with us are free, and a jeweler comes anywhere in the city, so an inspection doesn't require a trip. For such a visit, gather all your jewelry at once, so the jeweler can check several pieces in one meeting and tell you which one needs work first. A problem found early almost always costs less than searching for a lost stone.
We have gathered the key points that help keep jewelry intact and notice damage in time, from choosing a restoration method to home care and regular inspections.
8brands
We repair pieces from the brands that have their own pages on our site and choose the right approach for every item.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your dishwasher won't drain, the most common culprits are a clogged filter or drain hose; less often, it's the pump, impeller…
24 March 2026 · 12 minutes read
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
The easiest way to remove scale from a kettle is with citric acid: 1–2 tablespoons per liter of water, boil for 5–10 minutes, then drain and rinse.
17 March 2026 · 13 minutes read
If your laptop screen is broken, turn the device off first, don't press on the display, and check the picture through an external monitor.
12 March 2026 · 11 minutes read
Air conditioner errors are codes on the display or flashing indicators that show which component has failed.
5 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read












