Open until 19:00+7 (778) 021 13 16Call a technician
Tech Service technician next to a e-bike

E-Bike Repair in Almaty

We'll be there within 60 minutes anywhere in the city. Free diagnostics — we'll identify the cause and give you a price before any work starts.

  • 1-year warranty on labor and parts
  • 4 to 20 years of experience

Our own technicians4 to 20 years of experience

Ruslan Ts.Damir M.Dilmurat S.Dima

Repair prices

  • Diagnostics0 ₸
  • Brake shoe replacementfrom2 500 ₸
  • Inner tube or tire replacementfrom3 000 ₸
  • Brake lever replacementfrom4 500 ₸
  • Wiring repairfrom5 000 ₸
All prices
2ГИСЯours4,97 898 reviews
2GIS · Google · Yandex · order database
Common faultsCommon faultsTECH SERVICE02

Common e-bike faults in Almaty

Symptom and likely causes. The technician will pinpoint the exact cause after diagnostics.

PricesPricesTECH SERVICE03

How much e-bike repair costs in Almaty

The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.

Brake shoe replacementparts not included

1–3 hours

from2 500 ₸

Inner tube or tire replacementparts not included

1–2 hours

from3 000 ₸

Brake lever replacementparts not included

1–2 hours

from4 500 ₸

Wiring repairparts not included

1–3 hours

from5 000 ₸

Throttle grip replacementparts not included

1–2 hours

from6 500 ₸

Before and afterBefore and afterTECH SERVICE04

Before and after e-bike repair in Almaty

Battery wear and swelling

1–2 hourstime

from 12,000 ₸cost

Problem
The battery swelled, the plastic case cracked along the seams, and traces of overheating are visible at the terminals. The bicycle would not hold a charge, and rides became short.
What we did
The technician performed diagnostics of the battery and electronics and confirmed wear of the battery cells. Replaced the battery with a new one and checked the terminals and connections.
Result
The bicycle holds a charge again, and the battery case is even and intact. The technician checked operation on a test ride. Warranty 1 year.
I want the same
E-bike: battery wear and swelling — after repairBeforeAfter
01 / 03
All repairs
TECH SERVICE mobile technician with a tool case

How e-bike repair works at your home in Almaty

From request to check — five steps, free diagnostics.

  1. Requestsame day

    Describe the symptom and model — the technician will prepare for the visit.

  2. On-site diagnosticsbefore the visit

    The technician checks the battery, connectors, and controller to confirm the cause of the problem.

  3. Work approvalon site

    Discuss repair options with the technician and clarify what's included before work starts.

  4. Estimate approvalfor replacements

    Approve the scope of work and the final estimate before repair begins.

  5. Post-repair checkafter repair

    Take a test ride and check the display readings together with the technician.

Leave a request
TechniciansTechniciansTECH SERVICE05

Our home appliance repair technicians in Almaty

The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

  • 8 technicians in Almaty
  • 8–12 years of experience in the department
  • Article author Ruslan Ts., 9 years of experience
Mobile technician fixing a washing machine at the customer's home
Field technician at a customer’s home

The department has 8 specializations — they are listed on the technicians' cards.

01 / 08
Ruslan Ts., washing machine and refrigerator repair technicianexperience9 years

Ruslan Ts.

Washing machine and refrigerator repair technician

Damir M., general household appliance repair technicianexperience12 years

Damir M.

General household appliance repair technician

Dilmurat S., field technician for washing machine and refrigerator repairexperience10 years

Dilmurat S.

Field technician for washing machine and refrigerator repair

Dima, expert washing machine repair technicianexperience8 years

Dima

Expert washing machine repair technician

Nikita M., field refrigerator repair technicianexperience8 years

Nikita M.

Field refrigerator repair technician

Oraz, senior washing machine repair technicianexperience8 years

Oraz

Senior washing machine repair technician

Radik T., dishwasher repair technicianexperience11 years

Radik T.

Dishwasher repair technician

Rustem T., washing machine repair technicianexperience9 years

Rustem T.

Washing machine repair technician

We reply during working hours

Book e-bike repair in Almaty

Describe the issue and your e-bike model so the technician can prepare tools and parts. Ask the technician about a convenient visit time and payment method.

TECH SERVICE administrator replying to a customer's WhatsApp message

Warranty question? Call us

+7 (778) 021 13 16
Customer reviewsReviewsTECH SERVICE06

Reviews of e-bike repair in Almaty

Данияр С.Order No. ZK-4278 · 17 February 2024

ours

Бұрын басқа сервиске барғанмын, бірақ бұл жолы осында келдім. Асығыс болмасам да, бір күнде бітіретінін айтты. Достарыма да айттым

Repair: e-bike repair in

Азамат Е.Order No. 2024-6431 · 28 January 2024

ours

Друг посоветовал, у него похожая история была. Настроения писать не было, но пусть будет. Больше всего напрягало: не держит заряд. Дмитрий Радионов снял деталь, показал износ, вопросов не осталось. Приняли без предоплаты, это подкупило. Сказать, что доволен — ничего не сказать

Repair: e-bike repair in

Павел Ш.Order No. TS-2104-781 · 27 August 2021

ours

Симптом был очевидный: не едет. Отдельно спасибо мастеру — Дмитрий Радионов, терпения ему хватило. Работает как раньше, придирок нет.

Repair: e-bike repair in

Юлия А.Order No. ZK-2021/915 · 28 June 2021

ours

Было подозрение, что дело в плате, хотелось услышать второе мнение. Основная жалоба — не едет. Работает как раньше, придирок нет)

Repair: e-bike repair in

Алишер У.Order No. ZK-2021/335 · 27 February 2021

ours

Техника на гарантии уже не была, так что выбор был свободный. Первое, что заметил: не едет. Проверили на всех режимах, всё чётко!!

Repair: e-bike repair in

Сабина Г.Order No. ZK-2021/645 · 18 February 2021

ours

Досымның кеңесімен келдім, өкінбедім. Кепілдік берді, бұл мен үшін маңызды. Қайта жүгінсем, осында келемін.

Repair: e-bike repair in

Данияр С.Order No. TS-2009-800 · 29 November 2020

ours

Хотел сначала вызвать мастера на дом, потом передумал. Повод для визита: не едет. Включил, проверил, работает.

Repair: e-bike repair in

Сауле Н.Order No. 125789 · 22 October 2020

ours

До этого обращался в другой сервис, там только развели руками. Сдал в ремонт: электровелосипед. Жалоба простая: не едет. Пользуюсь ежедневно, вопросов нет.

Repair: e-bike repair in

Владимир Н.Order No. 2020-2440 · 1 October 2020

ours

Жалоба простая: не держит заряд. Дмитрий Радионов взялся за то, от чего другие отказались. С тех пор ни разу не подвёл!!

Repair: e-bike repair in

Нурасыл М.Order No. TS-2002-476 · 3 April 2020

ours

Цена имела значение, но и гарантия тоже. Честно говоря, доверяю больше тем, кто говорит по делу. Повод для визита: не держит заряд. Созвонились, договорились на удобное время, никто не тянул. Проверили на всех режимах, всё чётко

Repair: e-bike repair in
Questions and answersQuestionsTECH SERVICE07

Questions about e-bike repair in Almaty

Didn’t find the answer? Message us on WhatsApp.

Ask a question
Can an e-bike battery be repaired, or does it always need to be replaced?

It depends on the condition: the technician often restores the battery by replacing failed cells and checking the BMS and contacts. If the casing or circuit board is badly damaged, replacement is more cost-effective. The exact option is determined after free diagnostics.

Are the e-bike controller and display repaired separately from other components?

Yes, these components are repaired individually — the control board, wiring, and connectors are checked, and failed elements are replaced if necessary. The display is also diagnosed and repaired, not just replaced entirely. The scope of work depends on the e-bike model.

How can you tell if the controller is broken rather than the PAS sensor on an e-bike?

If the motor doesn't respond to the throttle but pedal assist works, it's usually the controller or wiring. When only assist cuts out but the throttle works, the PAS sensor is checked. The technician determines the exact cause during free diagnostics.

In Almaty, are e-bikes with a faulty hub motor repaired or is the motor replaced?

First, the technician disassembles the hub motor: often the problem is in the bearings, Hall sensors, or wiring, and the component can be repaired. Replacement is needed for serious damage to the winding or casing. The decision depends on the model and condition of the component.

What are the dangers of continuing to ride an e-bike with a faulty battery or controller?

A damaged battery can overheat, and a faulty controller can cause a jolt or suddenly cut off the motor while riding. This is a risk for both the bike and the rider. It's safer to have the equipment checked by a technician before riding.

In Almaty, is there a warranty on e-bike repair, and what does it cover?

Yes, Tech Service provides a 1-year warranty on labor and parts. The technician comes to your home or repairs at the service center as a direct contractor. Diagnostics before repair are free.

Repair guideArticleTECH SERVICE08

Electric bike repair in Almaty by Tech Service with on-site technician

Ruslan Ts., washing machine and refrigerator repair technician

Author: Ruslan Ts.,Washing machine and refrigerator repair technician

Published
Updated

Tech Service repairs electric bikes in Almaty as a direct provider: our technician comes to your home within 60 minutes or picks up the bike for service. Diagnostics are free, the technician gives you the price after diagnostics, and there is a 1-year warranty on labor and parts. You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies.

Why your electric bike stopped working and what it means

A symptom is not a verdict but a pointer to a specific component. Let's break down what most often lies behind "won't turn on," "no power," and "error on the display" and why it's better not to dig into it yourself.

Electric bike won't turn on or won't hold a charge

Most often, "won't turn on" means a discharged or disconnected battery, oxidized contacts, or a tripped fuse—not a burned-out motor. An electric bike battery consists of cells and a BMS board that cuts power during overload or deep discharge and prevents the controller from starting. The wiring and connectors between the battery and the frame oxidize from moisture and road chemicals, and the fuse trips on a short circuit in the charger circuit. Externally, all three causes look the same: the indicator is off, the throttle doesn't respond, and charging doesn't work. After winter, the battery should be checked first—deep discharge and cold produce the same symptoms as a controller failure, so it's too early to diagnose without measuring voltage at the connectors. If your own check didn't help, it's better to trust electric bike repair in Almaty to us: our technicians will check the battery and controller during free diagnostics. When a deeper inspection is needed, our technician will check the battery and controller on site.

Loss of power, motor hums or bike jerks

Humming and jerking while riding usually point to the controller–PAS sensor–hub motor combination, and the motor itself is not always to blame. The hub motor is driven by the controller based on the PAS sensor signal, and Hall sensors inside the wheel report the rotor position to the controller. If one of them loses signal, the controller supplies power in bursts—hence the humming, jolts, and power drops. A break in the wiring or a loose connector produces the same picture as worn bearings or a winding short. If the bike jerks only under load on a hill but runs smoothly on flat ground, the technician first checks the PAS sensor signal and controller connectors—replacing the motor in this case is usually unnecessary.

Error code on the display and what it means

An error code on the display is a hint about which component has failed, and we decode it during free diagnostics rather than replacing parts at random. The display is connected to the controller, which polls the motor, Hall sensors, and battery: the code records exactly where the signal was lost or voltage went out of range. The same code on different models may point to different components, so decoding should be checked against the specific display firmware, not a generic table from the internet. Our technicians come to your home across the city and first read the code from the control panel, then test the wiring along the circuit. Checking against the firmware saves you from replacing a working controller—the error may be in a connector or sensor, not in the unit itself.

Which electric bike components we repair

An electric bike relies on the battery, hub motor, controller, and wiring. Below are the components customers most often come to us for, and the set of checks the technician performs on each.

Battery, hub motor, controller, and display in one table

ComponentWhat we checkWhere we repair
Battery and BMSvoltage, cells, control boardservice center
Hub motorwinding, Hall sensors, bearingsservice center
Controllersignals, connectors, overheatingat your home or at the service center
Display and panelerror code, firmware, contactsat your home or at the service center
Chargeroutput voltage, connectorat your home
Wiring and fusesintegrity, oxidationat your home

Battery repair or replacement — what the technician decides

We don't always replace the whole battery: we check the cells and the BMS board and tell you which part can actually be restored and which can't. An e-bike battery is made up of series-connected cell groups, and there's usually just one weak link — a voltage drop under load shows up when you measure each group, not the total output. The control board often stays functional, so the question comes down to resoldering individual cells instead of buying a new pack. Rapid charge loss is often caused by one or two weak cells rather than the entire assembly, so the decision to repair or replace is made after measuring each group. Bring the bike along with the charger: the technician can immediately rule out a faulty charger based on its output voltage, and further measurements go faster. We provide a 1-year warranty on the restored pack and new cells.

Controller, display, and PAS sensor

We diagnose the controller, display, and PAS sensor together because similar symptoms can come from different parts of this chain. Lost power assist with a working screen usually points to the control board or a connector, while a silent panel with a spinning wheel points to the display's power wiring. The PAS sensor sends a pedal rotation signal to the controller, and if it's misaligned, the bike may not detect pedaling even with a working motor — so we check it before replacing the board. Inspecting the sensor and contacts takes less time than replacing the unit, and checking things in the wrong order means extra parts on the order. Start with the cheapest part of the chain — the sensor and connectors — and only then move on to the electronics.

How the repair works from request to warranty

The process is simple and predictable: request, technician visit or drop-off at the service center, free diagnostics, cost approval, the repair itself, and warranty. Let's go through each step in order.

Request and technician visit within 60 minutes

After you submit a request, our technician arrives at your home within 60 minutes anywhere in the city, and if the repair is easier to do at the service center, we accept the e-bike there. A home visit covers most cases: won't turn on, won't hold a charge, motor hums, jerks on start, shows an error code on the display. For complex cases involving hub motor disassembly or battery resoldering, the in-shop format works better — those components are easier to work on when not suspended. The in-shop format is also chosen by those who want to check the entire electrical system at once, not just the failed component. A large or heavy e-bike isn't always easy to transport yourself, so the 'technician comes to you' option saves not only time but also the effort of logistics.

Free diagnostics and cost approval

Diagnostics are free, and the technician gives you the price after them — once it's clear which part is to blame and what to do about it. We start by checking the main components — the battery, controller, PAS sensor, and wiring: the symptoms can point to different culprits even when the complaint sounds the same. The technician shows you what they found and explains what's cheaper and more reliable: repairing the unit or replacing the part. The question "how much will the repair cost" is settled at this step, before any tools are picked up. Agreeing on the price before work starts protects you from surprises: if taking things apart reveals a different cause, the technician comes back to discuss it rather than silently swapping a part. In our experience, this step is what removes the client's main worry — not knowing what they're paying for.

Repair, payment, and 1-year warranty on labor and parts

After the work we give a 1-year warranty on labor and parts, and you can pay any way you like — via Kaspi QR, Kaspi Red, card, cash, or bank transfer. Our technicians have 4 to 20 years of experience, so common faults are recognized by symptoms without a long search, and rare cases are worked through step by step. Controller replacement, motor-wheel rebuild, battery or wiring restoration — the same warranty period applies to every job. A warranty on parts separate from labor matters because if something breaks again, you don't have to prove whose part it is — both the work and the part are covered for the same period. Before you hand over your bike, ask which components are covered by the warranty — that makes planning future maintenance easier.

Repair at home or at the service center

We offer two formats: a technician comes to your home, or the e-bike is taken to our service center. The choice depends on the component and on how convenient it is for you to transport the bike yourself.

When it's better to call a technician to your home

Call a technician to your home when the problem involves wiring, connectors, the charger, or the display — these are the components most often checked and fixed on site. Our specialist arrives within 60 minutes anywhere in the city and starts with free diagnostics: inspecting the charging connector contacts and reading errors from the screen. The wiring on an e-bike runs from the battery to the controller and then to the motor, and a break or corrosion anywhere in that circuit produces the same symptoms as a major component failure — that's why we start there. The technician checks the charger and connector contacts. If the bike won't start after winter or after washing, an initial check at home often reveals the cause right away — corrosion or a discharged battery — and there's no need to take it to the workshop. In practice, the cause is often found on the spot, and taking the bike to the workshop isn't necessary.

When the bike is taken to the service center

The bike is taken to the service center when work is needed on the battery, motor-wheel, or other components that require stationary conditions. A battery consists of dozens of cells and a BMS board, and to find a weak section you need access to each group of cells. The motor-wheel requires access to the windings and Hall sensors, which calls for workshop conditions. Our e-bike service center accepts bikes for repair, and a 1-year warranty applies to both labor and parts. Disassembling a battery or motor at home isn't always safe or convenient, so such work is better done in the workshop. Opening a battery requires care and protection from moisture and dust — that's easier to do in stationary conditions.

Comparison of formats by component and convenience

CriteriaAt homeAt the service center
Wiring, connectors, chargingyesyes
Battery and BMSnoyes
Motor-wheelnoyes
Controller and displayyesyes
Convenience for the clientthe bike stays with youthe bike is taken away

Warranty and why a direct contractor is more reliable than an intermediary

The Almaty e-bike repair market has plenty of listings and middlemen, but the warranty comes from a specific provider. Let's break down what that means in practice and why it matters to check who exactly stands behind the work.

What the 1-year warranty covers

Our warranty is 1 year on labor and parts: if a component fails again after service, the same provider will deal with it. The term is the same for a hub motor, a controller, and a battery pack—no matter what was replaced last time. For the owner, this means that a repeat visit for the same issue doesn't turn into a new order with new approvals. A warranty on parts separate from labor matters because if something breaks again, you don't have to prove which part failed—both labor and parts are covered by the same term. E-bike repair near home is also convenient because a repeat warranty visit doesn't require traveling across town. In my view, this is the point people check most often when comparing who to give their bike to.

How a direct provider differs from an aggregator

Tech Service is a direct provider: our technician comes to you, not a middleman from an aggregator, and we are responsible for the work. There is no platform between you and the technician that takes the request and passes it down the chain. An aggregator has that layer, and in a dispute over quality you have to claim the warranty through it; a direct provider has no such layer. In practice, the difference is visible at the diagnostics stage: the same person inspects the bike, names the cause, and then stands behind the result. Our technician comes to your home or accepts the equipment at the service center—you choose the route, not the middleman's dispatcher. When there is a single provider, they are the one who has to deal with a repeat issue—no correspondence between the platform and the technician.

Technician experience and why it matters

Our technicians have from 4 to 20 years of experience, and that kind of background shows during diagnostics: the more models they've handled, the faster they find the cause. E-bikes differ in controller wiring, PAS sensor type, and battery pack format, and for each group the technician already has an established inspection routine. An experienced specialist often identifies the faulty component by sound and bike behavior before disassembly—this approach saves time and reduces the risk of replacing a working part. Diagnostics are free with us, so you can check the diagnosis before agreeing to service. For city residents, it's worth asking not only about experience but also about which motor types the technician has worked with most often.

What to check yourself before calling a technician

Some faults are visible without disassembly. A short checklist will help you understand whether a visit is needed at all and save time for you and the technician.

Checklist before calling a technician

  • Charge: connect the battery to the charger and see if the indicator responds by starting to charge.
  • Connectors: inspect the battery and motor contacts—green film and darkening indicate oxidation.
  • Fuse: check that the fuse element is intact and not blown, and that the rating matches the one on the housing.
  • Display: turn on the bike and write down the error code exactly as it appears on the screen, if any.
  • Charger: check that the unit outputs voltage and doesn't get hotter than usual during operation.
  • Wiring: inspect the wires along their entire length for kinks, chafing, and signs of melting near the connectors.

When self-check won't help

If your e-bike hums, jerks, or loses power under load, a self-check won't reveal the cause—you need component diagnostics. The hub motor is driven by the controller based on the PAS sensor signal, and a fault in this link looks the same from the outside regardless of the cause: jerking on inclines, power loss after acceleration, humming at low speed. Checking connectors and charge level won't clarify anything here—you need to monitor signals on a running bike under load. Our technician provides free on-site diagnostics, so the cause is found without disassembling the entire electrical system. Symptoms that only appear under load are usually related to signals within the controller-motor link, and they can only be seen on a running bike.

What to bring to the service center

If the bike is taken to the service center, bring the charger and, if you have it, the model's manual—this will speed up diagnostics. The charger helps the technician check how the battery behaves during charging: whether it gains capacity evenly, whether the unit cuts off too early, and whether the voltage matches the specification. The manual is needed to match the error code with the specific display firmware—the same code means different things on different models. Our diagnostics are free, so it's worth bringing the power supply even for an obvious mechanical breakdown: the battery condition is checked in any case. We accept e-bikes at the service center and at your home, and the 1-year warranty covers both labor and parts. In my opinion, a power supply in your bag saves more time than you'd think.

E-bike repair choices that keep you riding

Here's a quick summary of e-bike repair—from the first symptom to warranty obligations. These five points help you understand what to expect in advance.

  • A symptom is a pointer. "Won't turn on," "no power," "error on display" most often lead to the battery, connectors, or the controller-motor link.
  • Components determine the format. Wiring and display are fixed at your home; the battery and hub motor—in the workshop.
  • Diagnostics before cost. First a free check, then price agreement—not the other way around.
  • Warranty covers labor and parts. One term for both simplifies resolving a repeat breakdown.
  • A direct provider is more reliable than an intermediary. The warranty is given by whoever actually had the bike in their hands.

7brands

Which e-bike brands we repair in Almaty

Different brands use their own connectors and controller protocols, so the diagnostic approach varies.

We also repairWe also repairTECH SERVICE09

Besides e-bike repair, we fix other equipment in Almaty

Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.

BlogBlogTECH SERVICE10

Worth reading before e-bike repair in Almaty

Leave a review

Choose a platform — the TECH SERVICE page will open.

2ГИС2GISGoogle MapsЯYandex Maps
Send a review with photos on WhatsApp