Open until 19:00+7 (775) 030 02 94Call a technician
Tech Service technician next to a oven

Oven Repair in Almaty

A technician arrives within 60 minutes anywhere in the city. Free diagnostics.

  • 1-year warranty on labor and parts
  • Technicians with 4 to 20 years of experience
  • You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies

Our own technicians4 to 20 years of experience

Ruslan Ts.Damir M.Dilmurat S.Dima

Repair prices

  • Diagnostics0 ₸
  • Door seal replacementfrom4 000 ₸
  • Oven installationfrom5 000 ₸
  • Wiring repairfrom5 000 ₸
  • Backlight lamp replacementfrom5 000 ₸
All prices
2ГИСЯours4,97 898 reviews
2GIS · Google · Yandex · order database
Common faultsCommon faultsTECH SERVICE02

Common oven faults in Almaty

Below are typical symptoms and the components most often checked. The exact cause is confirmed by the technician after diagnostics.

PricesPricesTECH SERVICE03

How much oven repair costs in Almaty

The table shows oven repair costs: a starting labor price without parts and the timeframe; the technician confirms the final amount before starting the repair.

Door seal replacementparts not included

1–2 hours

from4 000 ₸

Oven installationexact price — after the free diagnostics

1–2 hours

from5 000 ₸

Wiring repairparts not included

1–3 hours

from5 000 ₸

Backlight lamp replacementparts not included

1–2 hours

from5 000 ₸

Mode switch replacementparts not included

1–2 hours

from5 500 ₸

Before and afterBefore and afterTECH SERVICE04

Before and after oven repair in Almaty

Not responding to knobs and buttons

1 visittime

from 11 500 ₸cost

Problem
The oven stopped responding to knobs and buttons, sometimes it would turn on and immediately turn off, and it worked when tapping on the panel.
What we did
The technician removed the control module, resoldered the wire connector pins where the solder had cracked, checked the contact with a tester, reinstalled the module, and checked all modes.
Result
The oven responds to knobs and buttons again, all modes work, and the contact holds.
I want the same
Kitchen with sage-green cabinet fronts, an open oven with the door folded down, a removed green circuit board in a black tray on a gray towel, a technician in an orange shirt soldering the connector pins with a soldering ironBeforeAfter
01 / 04
All repairs
TECH SERVICE mobile technician with a tool case

How oven repair works at your home in Almaty

Five steps from request to performance check.

  1. Requestsame day

    Agree on a convenient time and address with the technician.

  2. Technician visitwithin 60 minutes

    The technician arrives at the agreed time and inspects the appliance on site.

  3. Diagnosticson site

    The technician records the inspection results and agrees with you on the list of faulty components.

  4. Approval of workafter inspection

    You approve the scope of work and the part before the technician starts.

  5. Final costat completion

    The technician gives the final price including labor and parts, and you confirm the order.

Leave a request
TechniciansTechniciansTECH SERVICE05

Our home appliance repair technicians in Almaty

The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

  • 8 technicians in Almaty
  • 8–12 years of experience in the department
  • Article author Ruslan Ts., 9 years of experience
Technician repairing a oven at a customer’s home
Field technician at a customer’s home

The department has 8 specializations — they are listed on the technicians' cards.

01 / 08
Ruslan Ts., washing machine and refrigerator repair technicianexperience9 years

Ruslan Ts.

Washing machine and refrigerator repair technician

Damir M., general household appliance repair technicianexperience12 years

Damir M.

General household appliance repair technician

Dilmurat S., field technician for washing machine and refrigerator repairexperience10 years

Dilmurat S.

Field technician for washing machine and refrigerator repair

Dima, expert washing machine repair technicianexperience8 years

Dima

Expert washing machine repair technician

Nikita M., field refrigerator repair technicianexperience8 years

Nikita M.

Field refrigerator repair technician

Oraz, senior washing machine repair technicianexperience8 years

Oraz

Senior washing machine repair technician

Radik T., dishwasher repair technicianexperience11 years

Radik T.

Dishwasher repair technician

Rustem T., washing machine repair technicianexperience9 years

Rustem T.

Washing machine repair technician

We reply during working hours

Book oven repair in Almaty

Choose a convenient visit time and mention your oven model when you request service so the technician brings the right tools and parts.

TECH SERVICE administrator replying to a customer's WhatsApp message

Warranty question? Call us

+7 (775) 030 02 94
Customer reviewsReviewsTECH SERVICE06

Reviews of oven repair in Almaty

Жасмин Р.Order No. 2026-1686 · 7 August 2026

ours

Искал мастерскую поближе к дому, чтобы не мотаться с техникой через полгорода. Позвонил узнать про ремонт духовки. Проблема — не греет. Вышло дешевле нового, что логично. Заодно поменяли: тэн. Позвонили заранее, предупредили, что задержится на полчаса. Шум пропал, работает мягко)

Repair: oven

Светлана Д.Order No. 737720 · 15 July 2026

ours

Жалоба простая: не закрывается. Дамир М приехал в тот же день, хотя был конец смены. Вернули в тот же день, всё функционирует.

Repair: oven

Татьяна Б.Order No. TS-2509-349 · 17 April 2025

ours

Танысым осы жерді мақтап, кеңес берді. Алдымен интернеттен іздедім, кейін таныстарым осы жерді ұсынды. Ұсақ ақауларды да тегін жөндеп берді. Бағасын алдын ала келістік, соңында өзгерген жоқ. Жұмыс сапасы жақсы, артық шуы жоқ. Диагностика тегін болды, бұл жағы жақсы. Мастер ақауды түсіндірді, қажетсіз нәрсе таңбады. Екінші рет хабарласуға тура келді, бірақ кінә оларда емес. Ұсынамын, текке ақша алмайды.

Repair: oven

Алексей Г.Order No. TS-2412-273 · 5 August 2024

ours

Симптом был очевидный: не греет. Дамир М честно сказал, что менять, а что ещё походит. Сделали аккуратно, следов разборки не видно)

Repair: oven

Алмас Д.Order No. 2024-6592 · 14 April 2024

ours

Жалоба простая: не закрывается. Отдельно спосибо мастеру — Дамир М, терпения ему хватило. Проверили на всех режимах, всё чётко.

Repair: oven

Роман З.Order No. 582123 · 5 January 2024

ours

Алдымен интернеттен іздедім, кейін таныстарым осы жерді ұсынды. Алдын ала айтқан уақыттан ерте бітірді. Бағасын алдын ала келістік, соңында өзгерген жоқ. Мастер ақауды түсіндірді, қажетсіз нәрсе таңбады. Бағасы базардағыдан қымбат емес. Кәсіби мамандар, рақмет.

Repair: oven

Зарина Ш.Order No. ZK-2023/856 · 12 October 2023

ours

Выбирал по отзывам в 2ГИС, времени на эксперименты не было. Больше всего напрягало: не держит температуру. Уже полгода — ни одного сбоя.

Repair: oven

Алия Ш.Order No. TS-9585 · 25 September 2023

ours

С чем пришёл: не закрываеться. Радик Т объяснил причину так, что понял даже я. Ребёнок уже проверил на прочность, держится.

Repair: oven

Зарина Ш.Order No. ZK-2023/252 · 3 August 2023

ours

Друг посоветовал, у него похожая история была. Честно говоря, доверяю больше тем, кто говорит по делу. С чем пришёл: не держит температуру. Приехал без записи, приняли как есть. Вышло дешевле нового, что логично. Поменяли: термостат. Спасибо, выручили. Сделали аккуратно, следов разборки не видно!!

Repair: oven

Гаухар Н.Order No. 2023-8447 · 2 July 2023

ours

Проблема — не закрываеться. Отдельно скажу про мастера: Дамир М — спокойный, без лишней суеты. Сделали и забыл про проблему

Repair: oven
Questions and answersQuestionsTECH SERVICE07

Questions about oven repair in Almaty

Didn’t find the answer? Message us on WhatsApp.

Ask a question
Can I fix the oven myself or is it better to call a technician?

You can replace the bulb or the seal yourself if you have the tools and feel confident. But if there are problems with heating, wiring, or electronics, it's better to call a technician: it's safer and won't lead to new breakdowns.

How can I tell if the thermostat or the heating element is broken?

If the oven doesn't heat up at all, the heating element is usually to blame, but if it heats more or less than the set temperature, the thermostat is suspected. Diagnostics help pinpoint the faulty part: a technician checks both elements, and it depends on the model.

Do you repair gas ovens at home in Almaty?

Yes, gas ovens are repaired at home if no intervention in the gas line is required. A Tech Service technician comes to your home in Almaty and fixes burner, thermostat, and ignition issues on site.

What should I do if the oven door no longer closes tightly?

Check if dirt or dishes are in the way and inspect the seal for damage. If it's worn out or deformed, it will need to be replaced, which a technician can do at your home.

Is an error code on the oven display dangerous?

The code indicates a specific malfunction, and some of them can indeed be dangerous. Don't ignore the signal: it's better to call a technician to interpret it and fix the cause to avoid a breakdown or fire.

Do you repair ovens at home in Almaty or take them to a service center?

Most breakdowns are fixed by a technician at your home, and the oven is taken to a service center only for complex electronic issues. Diagnostics are free, and the technician will tell you if it can be fixed on site.

Repair guideArticleTECH SERVICE08

Oven Repair in Almaty by Tech Service with On-Site Visits

Ruslan Ts., washing machine and refrigerator repair technician

Author: Ruslan Ts.,Washing machine and refrigerator repair technician

Published
Updated

Tech Service repairs ovens and built-in ovens in Almaty as a direct contractor: our technician comes to your home within 60 minutes or the work is done at our service center. Diagnostics are free, there is a 1-year warranty on labor and parts, and the technician gives you the price after diagnostics. We fix electric, gas, and combination ovens.

Why the Oven Isn't Heating and What Exactly Broke

The oven turns on but doesn't heat — this is almost always one of four components. Here's how a technician tells the heating element from the thermostat, relay, and wiring.

The Oven Turns On But Doesn't Heat

During diagnostics, our technician first checks the heating element with a multimeter — a working element shows resistance within the normal range, while a broken or shorted one produces no heat. Next in the chain are the thermostat, relay with contactor, and terminal connections: each component either supplies power to the heater or cuts it off when the set temperature is reached. In electric models, the upper and lower heaters and the grill each have their own role, and failure of one isn't always immediately noticeable — the cavity heats, but slower and weaker. In gas ovens, a burner with a thermocouple and valve works instead of a heating element, and the troubleshooting logic is different. If the heating element is intact but there's no heat, the cause is usually the thermostat or relay — they allow heating, and their failure looks exactly like a dead heater.

Why the Oven Trips the Breaker or Blows Fuses

Most often, the breaker trips due to a heating element shorting to the body or a short circuit in the oven's wiring and terminals, and our technician starts by checking the heater's insulation. A megohmmeter shows current leakage to the body that isn't visible externally: the element looks intact, but when it heats up, it shorts and the breaker trips after a few minutes of operation. The second common area is the terminal block and wire harness: burnt insulation, oxidized contacts, signs of melting at the connector. The third possibility is moisture in the cavity or on contacts after washing — this causes a one-time trip that doesn't repeat. If the breaker holds when the oven is unplugged but trips when it's turned on, the problem is in the appliance itself, not the home's electrical wiring, and this narrows the search to a few components.

Why the Oven Heats Unevenly and Doesn't Bake Through

Uneven heating is most often related to the convection fan or one of the heaters that has stopped working, rather than the oven's design. The fan circulates hot air throughout the cavity, and if the impeller is rubbing against the casing, humming, or has stopped, heat is distributed only from the bottom or only from the top — a sponge cake rises on one side, meat cooks in patches. Failure of the grill element or upper heater gives a similar picture but with a clear boundary: the bottom bakes, the top stays pale. A thermostat with worn calibration overstates the actual temperature by tens of degrees, turning a 180 setting into 150 or 210. Before replacing the fan, the technician checks whether it spins under load and whether the door seal is clogged — heat loss through a loose seal has the same effect as weak convection.

Error Codes and How Diagnostics Work

A signal on the display is a hint, not a verdict. Here's what groups of errors mean, why resetting doesn't fix the cause, and which components the technician checks first.

What an Error Code on the Oven Display Means

An error code points to a specific component — temperature sensor, control module, or heating circuit — but doesn't replace diagnostics, because the same code can have several causes. In electric models, a combination like E01 or F2 is most often related to an open or shorted temperature sensor, while overheating messages point to a stuck relay on the control board. In gas ovens, separate signals indicate ignition and flame control problems. Resetting with a button clears the message from the screen but doesn't fix the fault: if the cause remains, the message will return during the next heating cycle. In my opinion, noting the code and the conditions when it appears — before switching on, during preheating, or at the end of cooking — is more useful than immediately clearing the message: this detail narrows the search to one or two components and saves time on checks.

How Free On-Site Diagnostics Work

During the free diagnostics, our technician checks the heating element, thermostat, relay, and wiring with a multimeter to pinpoint the exact cause and cost of work before starting. First, they inspect the oven under load: turn on the heat and see at what stage the failure occurs. Then they test the heating element for breaks and insulation breakdown, compare the temperature sensor readings with the actual heating of the chamber, and check the relay contacts and wiring integrity. An on-site check is possible because most oven components are accessible after removing the back panel and don't require a test bench—so the cause is usually found in one visit. The technician arrives within 60 minutes of your request anywhere in the city, and after the inspection you get a clear list of work with no vague wording.

What breakdowns the technician fixes on site

FaultWhat we checkWhere we fix it
Not heatingHeating element, thermostat, relayAt your home
Trips the breakerHeating element insulation, wiringAt your home
Uneven heatingConvection fanAt your home
Door won't closeHinges, sealAt your home
Mode failuresControl moduleBased on diagnostics

Repair at home or at the service center

We fix most ovens right at your home, but there are cases when it's wiser to bring the appliance to the service center. Here's how the technician decides on the format of work and how many visits it will take.

When the oven is repaired at home

We repair ovens at home in most cases, because the heating element, thermostat, fan, hinges, and seal are accessible after removing the panels without taking the appliance away. The on-site technician arrives within 60 minutes anywhere in the city with tools for the specific complaint: weak heating, convection failure, loose door. Diagnostics are free, and right in your kitchen you can see whether the heating element, temperature sensor, or hinge fasteners need replacing. A built-in oven is actually easier to fix in place than to transport: you don't have to remove it from the kitchen and risk damaging the furniture during transportation. In my view, the benefit here is not only preserving the cabinetry—the client sees the whole process and can immediately test the result with their own cookware.

When repair at the service center is needed

We send the oven to the service center when work on the control module or testing of components can't be properly done on site. The electronic unit, display board, and convection wiring require a test bench and calm disassembly without rushing in someone else's kitchen. The technician records the complaint, removes the panel, and assesses whether the issue can be solved at the stove or a workshop is needed. Only a small portion of requests require transportation—most often it's boards that need to be tested under load on a bench rather than with a simple continuity check. The decision on the format of work is made after diagnostics, not in advance over the phone—so the client doesn't pay for transportation if the fault can be fixed on site. From our team's experience, this approach saves both time and nerves: the appliance doesn't leave the apartment without a confirmed cause.

How many visits are needed for repair

A typical repair fits into one technician visit: diagnostics and replacement of the component are done back-to-back if the cause is confirmed on site. A Tech Service specialist arrives within 60 minutes, opens the panels, checks the heating and control circuit, then installs the part and tests the oven in operating modes. The 1-year warranty covers both labor and parts—one visit gives you both the result and the coverage. Scheduling a second visit only makes sense for cases involving the control module: there, diagnostics are needed first, and then a repair decision. Moreover, diagnostics are free regardless of the outcome, so a repeat call doesn't turn into an extra expense for the client.

Gas vs electric ovens: what's the difference

Gas and electric ovens break down differently, and the approach to fixing them is different. We explain the differences and when restoration no longer makes sense.

How Gas Oven Repair Differs from Electric

We service gas ovens with extra care, because here the risk of a gas leak adds to the electrical side, and checking for leaks comes first. On a gas model, the technician first inspects the line connections, checks the burner flame and the thermocouple that cuts off the gas supply if the flame goes out. With an electric oven, the logic is different: heating comes from the heating elements, so the focus is on the thermostat, the elements and the relay, and there's no gas in the circuit at all. The tool kit and the order of checks differ between these two types, so the oven technician confirms the type before the visit to avoid going back for a part. Our technician arrives at your home within 60 minutes anywhere in the city, and diagnostics are free — he confirms the appliance type over the phone before the visit. An electric oven with a fault usually just stops heating, while a gas one may give off a smell or have a weak flame — that's a signal not to put off calling a technician.

What Types of Ovens We Repair

Oven typeRepair specificsWhat we check first
Electricheating from elementselement, thermostat, relay
Gasrisk of gas leakleak-tightness, flame
Combinationgas plus electricsboth circuits
Built-in ovenaccess after removing panelsheating, controls
Part of a rangeshared body with cooktopheating, wiring

When Oven Repair Isn't Worth It

Restoration stops making sense when the fault affects several expensive components at once or the body and cavity are seriously damaged. Fixing an oven with a burned-through bottom, cracked enamel and damaged wiring means replacing the cavity and the harness, and that's already comparable to buying a new model. Another criterion is the control module: if it fails along with the heater, the total scope of work grows, and replacing one component doesn't solve the problem. At the same time, no heating with working controls is usually fixed by replacing the heating element — that's a simple and predictable case. The decision should be made after diagnostics, not by appearance: the same "not heating" can be either a cheap element replacement or a complex module repair. A one-year warranty on labor and parts applies even when only some components are replaced — that's another reason to hear the technician's verdict first rather than rush out for a new oven.

Door, Seal, and What You Can Check Yourself

Some faults can be safely checked on your own before the technician arrives, while some components are better left alone. Let's look at where the line is and what to do so things don't get worse.

What to Do Before the Technician Arrives

  • Cut the power to the oven: unplug it from the outlet or switch off the circuit breaker in the panel before the specialist arrives.
  • Don't turn it back on: if the breaker tripped or you smelled burning, restarting won't help.
  • Check the outlet: look for melting and find out whether the breaker holds with the oven unplugged.
  • Note the error code: if one appeared on the display, it will speed up the free diagnostics and narrow down the causes.
  • Don't take the body apart: it's dangerous to touch internal components under voltage, and a shorted heater trips the breaker when you turn it on.
  • Remove the dishes: take out the trays and racks so the technician can reach the faulty component faster.

What You Can Check Yourself Without Risk

You can safely check the outlet, the circuit breaker, how tightly the door closes, and whether the light works — this doesn't require taking the case apart. Inspect the outlet and apartment wiring for melting and smell, and the breaker for tripping when the oven is off. Check the door seal for cracks and tears, and the light visually through the glass without removing it. But it's better not to replace the heating element or thermostat yourself: without testing with a multimeter, it's easy to install a working part instead of a burnt-out one and not solve the problem. During diagnostics, our technician checks the heating element, thermostat, relay, and wiring to find the real cause rather than replacing components at random — that's how the oven gets fixed right the first time.

Why the door stopped closing tightly

A door that doesn't close tightly is most often due to worn hinges or seal, and we restore the fit by adjusting the hinges or replacing the seal. Over time, hinges sag under the weight of the door, and the seal loses elasticity and cracks at the corners. Adjustment restores the door's geometry, and replacing the seal restores tightness around the entire perimeter. Even a small gap between the door and the body leads to heat loss, making the oven take longer to heat and use more energy — so it's better not to delay. If the door sags and catches the body, hinge adjustment should be done before the seal wears out, otherwise both components will need replacing. We check the fit around the entire contour and select a seal for the specific model.

Warranty and service terms

We explain the terms without fine print: what exactly the warranty covers, how the cost of work is determined, and why we work as a direct contractor rather than through an intermediary.

What the 1-year warranty covers

We provide a 1-year warranty on labor and parts, including replaced heating elements, thermostats, and control modules. The heating element and electronics are the most expensive components in an oven, and they are the ones that most often fail again due to poor soldering or a cheap analog part. Replacing the heating element, installing the thermostat, and control module are all covered by a single term — one year, not the formal two weeks usually given for such work. Warranty on the part and on the work are different things, and covering both means that if the same component fails again, the client doesn't pay twice: neither for a new part nor for a repeat visit. This is especially important for control modules, where the cost of a diagnostic error is highest.

How the cost of work is determined

The technician quotes the price after free diagnostics, when the cause is already known, not over the phone before inspection. It's impossible to guess the fault from a description like 'not heating' or 'tripping the breakers': similar symptoms can be caused by a burnt-out heating element, a failed thermostat, insulation breakdown to the body, or an oxidized contact in the power circuit. Our technician arrives, disassembles the component, tests the circuit with a multimeter, and only then names the sum — with the specific part and scope of work. This procedure protects against surprises at the end: the client approves the work with the exact cause known and understands what they are paying for, rather than learning the total after disassembly. Diagnostics are free — you don't pay for the inspection and finding the cause, even if you decide to decline the work.

Why we work as a direct contractor

Tech Service is a direct contractor: our technician comes to you, not an intermediary, so we are responsible for the work, not a subcontractor. An oven repair technician with 4 to 20 years of experience arrives within 60 minutes anywhere in the city — from outlying residential areas to central Almaty. The same person performs diagnostics and repairs and then handles the warranty, rather than forwarding the request to a third party. The no-intermediary scheme eliminates the dispatcher's markup and blurred responsibility: if the same fault recurs, you return to the same specialist instead of starting the search anew. That's why the 1-year warranty works in practice and doesn't remain just a line on paper.

Oven repair tips worth remembering

Diagnosing oven failures comes down to a few practical points: from pinpointing the exact cause of the breakdown to keeping the appliance safe until the technician arrives.

  • The cause matters more than the symptom: "not heating" can mean a failed heating element, thermostat, relay, or wiring — only diagnostics can tell for sure, not guesswork.
  • An error code is a clue: it points to a specific component, but a simple reset doesn't fix the cause, and the fault returns on the next heating cycle.
  • Diagnostics determine the type of work: most breakdowns can be fixed on-site, while complex components require service center work.
  • Safety before the technician arrives: unplug the oven and don't turn it on again if it trips the breaker or fuses.
  • Warranty on labor and parts: covering both protects you from paying twice for the same component if the issue recurs.

41brands

Which oven brands we repair in Almaty

The technician sources the part by model or part number, so repairs are possible for the appliances listed.

We also repairWe also repairTECH SERVICE09

Besides oven repair, we fix other equipment in Almaty

Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.

BlogBlogTECH SERVICE10

Worth reading before oven repair in Almaty

Leave a review

Choose a platform — the TECH SERVICE page will open.

2ГИС2GISGoogle MapsЯYandex Maps
Send a review with photos on WhatsApp