Diagnostics
Backlight check
- Sign
- image visible under external light
- What is checked
- LED integrity and power circuit
- Timeframe
- depends on the scope of work
- Cost
- quoted after diagnostics
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 021 13 16Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
We restore TV electronics: free diagnostics, a technician at your door within 60 minutes anywhere in the city, and a 1-year warranty on labor and parts.
Our own technicians4 to 20 years of experience




1 yearwarranty on labor and parts
60 minutestechnician visit anywhere in the city
freediagnostics
Electronics restoration includes soldering and component replacement, trace repair, reflashing, and setup. 1-year warranty on labor and parts.
01
Step 1quick
We look for bulging capacitors, solder cracks, and signs of overheating. Inspecting under magnification helps spot microcracks.
02
Step 2quick
We check test points and backlight circuits with a multimeter. We compare the readings against the TV's schematic.
03
Step 3depends on the scope of work
We replace failed parts and repair traces. We use a soldering station and flux.
04
Step 4as needed
We update the software if the firmware has failed. We reset settings to working values.
05
Step 5quick
After reassembly, we turn on the TV and check the picture, sound, and remote response. We make sure the issue is resolved.
5
Five typical symptoms point to power or board issues. Diagnostics will pinpoint the exact cause.
TV won't turn on
The indicator light is off or blinking, and the screen stays dark. Often the power supply or startup circuit is at fault.
Reboot loop
The TV turns on and immediately off, and the cycle repeats. The cause is a power or firmware failure.
Turns on but no sound
There's a picture but no sound, or the sound cuts out. The audio path and speakers are checked.
No response to the remote
The buttons on the TV also don't work. This may indicate a control board malfunction.
Turns off by itself
The TV shuts down after warming up, especially at high brightness. Often related to component overheating.
After warming up, the TV may turn off by itself — a sign of board overheating.
Describe the symptomsIf the screen is dark but you can see a faint image with a flashlight, the backlight is likely faulty.
Diagnostics
or
Diagnostics
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1–2 hourstime
from 10 000 ₸cost

BeforeAfterThe digital device repair department in Almaty has 7 technicians with 7 to 18 years of experience.

The department has 7 specializations — they are listed on the technicians' cards.
experience10 yearsSenior TV repair technician
experience10 yearsTV board repair technician
experience10 yearsElectromechanical technician
experience13 yearsAudio and DVD repair technician
experience18 yearsSmartphone repair technician
We reply during working hours
Unplug the TV, note the symptoms, and don't open the case. This will help the technician find the cause faster.

Warranty question? Call us
+7 (778) 021 13 167 898 reviews of repairs at TECH SERVICE in total
Гаухар Н.Order No. ZK-3515 · 6 August 2023
oursПрочитал кучу отзывов, половина — реклама, но тут вроде живые. Симптом был очевидный: зависает. Пользуюсь ежедневно, вопросов нет.
Лилия В.Order No. 25349 · 20 January 2023
oursИскал мастерскую поближе к дому, чтобы не мотаться с техникой через полгорода. Всё оформили по договору, с печатью. Второй месяц — полёт нормальный.
Нурасыл М.Order No. TS-1530 · 2 December 2022
oursНужен был счёт и чек, у нас техника на балансе организации. Оставил заявку на ремонт спутникового ресивера. Основная жалоба — зависает. Отдельно скажу про мастера: Сергей Архипов — спокойный, без лишней суеты. Заплатил 25 000, и не жалею. Приняли без очереди, оформили за пять минут. Второй месяц — полёт нормальный)
Ирина Т.Order No. 342249 · 4 August 2022
oursСмотрел, у кого есть запчасти на такую модель. Все разъёмы на месте, ничего не люфтит.
Лилия В.Order No. TS-4617 · 10 February 2020
oursАлдын ала бірнеше жерге қоңырау шалдым, бірақ нақты жауап осында ғана алдым. Таңертең жұмыс істеп тұрды, кешке қарай үнсіз қалды. Асыққан адамға ыңғайлы.
Ольга М.Order No. TS-1909-475 · 27 December 2019
oursЖалоба простая: слетела прошивка. Сергей Архипов помог выбрать, без навязывания. Сказать, что доволен — ничего не сказать.
Алия Ш.Order No. 98100 · 16 July 2018
oursЖалоба простая: зависает. Дамир М объяснил причину так, что понял даже я. Сказать, что доволен — ничего не сказать
Зарина Ш.Order No. TS-9260 · 10 April 2017
oursДо этого обращался в другой сервис, там только развели руками. Позвонил узнать про ремонт телевизора. Основная жалоба — не включается. Дамир М перезвонил, когда всё было готово. Заодно поменяли: подсветка. Сказали 9 500, я согласился без торга. Объяснили по телефону, что можно не везти, но я всё равно привёз. Все разъёмы на месте, ничего не люфтит
Ксения И.Order No. TS-2429 · 3 March 2017
oursЖалоба простая: не включается. Дамир М снял деталь, показал износ, вопросов не осталось. Проверили на всех режимах, всё чётко)
Молдир С.Order No. ZK-2016/515 · 19 November 2016
oursПозвонил знакомому, он раньше работал в сервисе, посоветовал этих. С чем пришёл: слетела прошивка. Внешне как новый, если не считать мелкой царапины.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionChip re-soldering is possible if the damage is localized and suitable components are available. In complex cases, replacing the board may be more cost-effective, but the technician decides after diagnostics, depending on the model.
Most often, the cause is a firmware failure or a motherboard issue. The exact diagnosis will be made by a technician after free diagnostics, as the behavior depends on the model.
During a voltage surge, the power supply and motherboard components often fail. A blinking indicator points to protection, but diagnostics will reveal the exact cause.
Problems with Wi-Fi and HDMI may be related to the motherboard or its modules. Accurate fault detection requires diagnostics, as the causes depend on the model.
Repair after liquid damage is possible if oxidation hasn't damaged critical circuits. The technician will assess whether restoration is feasible, and in cases of severe damage, may recommend replacing the board.
Yes, chip re-soldering and firmware flashing come with a 1-year warranty on labor and parts. Warranty terms depend on the specific case and TV model.
Tech Service repairs TV motherboards in Almaty as a direct contractor with its own technicians. Diagnostics are free, a technician arrives at your home within 60 minutes anywhere in the city, and you get a 1-year warranty on labor and parts. The technician gives you the price after free diagnostics, before any work starts.
The motherboard controls power, picture, sound, and Smart features, so when it fails, the symptoms are distinctive—and it's important to tell them apart from faults in other components.
A reboot loop on the logo usually points to a firmware failure or a board fault, and that's the first scenario our technician checks. First, they connect the set to a programmer and read the boot log: freezing on the startup screen with a repeating cycle means the Smart module isn't initializing and keeps restarting. On Samsung models, this symptom is often accompanied by the TV turning itself on at regular intervals. We reflash the device and check whether it boots normally after a restart. If the loop continues after the firmware is restored, the cause is in the board's hardware, and then chip rework is unavoidable. TV motherboard repair cost depends on the nature of the fault, and the technician gives you the exact amount after free diagnostics. Firmware won't fix a board with memory or power faults—it only masks the problem temporarily, so a repeated logo loop tells the technician it's time for hardware diagnostics. This approach saves time: software causes are ruled out before the case is even opened.
Board failures come from external impacts and internal wear, and the type of cause determines whether the unit can be restored or needs replacement.
After a power surge or lightning strike, the board's power circuits are the first to burn out, and for us such calls start with checking the standby mode. A pulse from a lightning discharge or a switching surge in the city grid passes through the power supply and reaches the motherboard's primary circuits—blowing capacitors, zener diodes, and PWM controllers. Standby mode shows whether voltage reaches the unit at all: if the indicator blinks or doesn't light up, the defect is often localized. A short in the backlight circuit or at the power supply output gives a similar picture—the TV won't start, even though the processor itself is intact. A blinking indicator doesn't always mean the board is completely dead; often it's enough to restore the power circuits and replace the burned components. Our technician on site first tests the primary circuits and only then concludes how extensive the damage is.
Moisture causes contacts to oxidize and can short the board, but if you act quickly, the motherboard can often be restored. Spilled tea, condensation after temperature changes, or drips from the balcony settle on the traces and under the chips, triggering electrochemical corrosion — the metal of the traces dissolves, and oxidation products short adjacent contacts. The first signs don't appear immediately: the TV works, then the sound or picture disappears, or stripes appear. The longer the unit stays wet under power, the deeper the corrosion of the traces — the metal breaks down across the entire area, not just at the edge of the spill. The first thing to do when liquid gets inside is to unplug the TV and not turn it on until diagnostics. A board after moisture exposure can be restored if the traces haven't burned through.
The choice between repairing and replacing the board depends on the nature of the fault, the age of the TV, and the availability of a compatible board for the specific model. Let's look at both scenarios.
| What we repair | When repair makes sense | When replacement is needed |
|---|---|---|
| Chips and microcircuits | Mounting pads are intact, traces are not damaged | Charring or delamination of the base |
| Power circuits | A single component burned out | Multiple connected circuits are damaged |
| Firmware | Failure without physical damage | Memory controller is unreadable |
| Connectors | Contacts detached without pad separation | Pads torn off along with traces |
Restoring the board of an old TV makes sense as long as the other components are working and a compatible board is available for the model. Replacing a chip or restoring a power circuit costs less than replacing the entire device if the matrix has no spots or dead pixels and the LED backlight works evenly across the entire screen. It's a different matter when the faulty board is combined with worn backlight or degraded LCD matrix — then the investment in such work should be evaluated together with the condition of the whole TV, not just the board. In my opinion, for models with a rare board and a working screen, it's wiser to first hear the technician's verdict after diagnostics than to immediately look for a new TV. The technician explains which elements can be restored and which are replaced entirely, and on that basis the owner decides on further steps.
Diagnostics begins with separating the motherboard from adjacent components, and then the technician determines which elements require intervention and subsequent soldering.
Diagnostics are free at our shop, and the technician gives you the repair price after the check, before any work begins. The inspection includes measuring supply voltages, checking for signs of overheating and oxidation, testing the output stages, and continuity testing the backlight and panel control circuits. Based on the results, the specialist shows you which unit failed and which components need resoldering, and you decide whether to go ahead with the repair or just get a consultation. We only start TV motherboard repair in Almaty after this check, so we don't replace parts that are still good. For Smart TVs and Android TVs, we also check the firmware and Smart module: app boot failures often look like hardware faults, and confusing the two doesn't help anyone. In my view, an honest diagnosis before the soldering iron saves more than a quick guess-and-go approach — that's why we don't start resoldering until we've ruled out related components.
How we work and what the warranty covers directly affect your decision, so it's important to understand how the technician arrives, where the board is repaired, and what the warranty covers after resoldering.
The technician arrives at your home within 60 minutes anywhere in the city, and if the board work requires shop conditions, the TV is taken there. We work as a direct provider: our own specialist comes to your address, not a middleman who passes the request to a third party. A home visit works for diagnostics, checking power circuits, and replacing accessible modules, but boards with dense mounting are better soldered at the shop. For Almaty residents, this saves time: you don't have to haul a heavy TV across town on a guess — first the technician confirms the cause, then you choose where the work happens. Complex chip resoldering is done at the shop, where the board sits on a bench without transport vibration. In my view, a home visit saves time at the inspection stage, not for every operation at once. Ask the technician which tasks they'll do on site — that saves you an unnecessary TV trip.
We provide a 1-year warranty on labor and parts, and it also covers chip resoldering and firmware restoration. The warranty period is the same for on-site service and shop work — it doesn't depend on where the work was done. If the TV freezes on the logo again or gets stuck in a reboot loop after the repair, that's a reason for a free warranty re-diagnosis. Reflashing the firmware yourself in that situation makes it harder to find the original fault. The warranty for resoldering memory chips and restoring firmware works the same as for replacing modules. Before you contact us, note exactly how the TV behaves: which screen it freezes on and how many seconds until it reboots — these details speed up the re-diagnosis.
Here's the key information for any TV owner who suspects a motherboard issue — from the first symptoms to warranty obligations.
If you ask, the technician will check other parts during the same visit.

If your TV won't turn on, first check the outlet, power cable, and the button on the TV itself—not the remote.
21 November 2025 · 12 minutes read
If your laptop screen is broken, turn the device off first, don't press on the display, and check the picture through an external monitor.
12 March 2026 · 11 minutes read
If your phone won't charge, start by checking the adapter, cable, and port, then the charging settings.
16 February 2026 · 12 minutes read
If your laptop freezes, the first thing to do is restart it and check Task Manager to see what's loading the CPU and memory.
25 January 2026 · 12 minutes read
If your phone falls in water, take it out right away, turn it off, and don't charge it.
19 January 2026 · 12 minutes read
If your phone camera isn't working, first check app permissions, clear the cache, and restart your phone — this fixes some software glitches.
24 December 2025 · 13 minutes read





