experience10 yearsMaksim S.
Graphics card repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (775) 031 92 28Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
We get hubs, relays, locks, and cameras working again. A technician arrives within 60 minutes anywhere in the city.
Our own technicians4 to 20 years of experience




Repair prices
The symptoms we see most often and their likely causes, starting with the most common. The technician confirms the exact cause after a free diagnostic.
no power, firmware failure, burnt-out unit
from7 500 ₸
wrong password, weak signal
from6 000 ₸
channel overload, cloud failure, firmware
from5 000 ₸
broken line, stuck contact, circuit
from6 500 ₸
dead battery, worn drive
from4 000 ₸
power loss, recording failure
from5 500 ₸
device conflict, condition error
from5 500 ₸
lost link to the hub, scenarios reset
from6 000 ₸
Call-out and typical automation jobs, with what's included in each service.
5 steps

Five steps from request to checking the system after repair.
Describe the symptom and device model so the technician brings the right tools.
We agree on the visit time and access to devices and the electrical panel.
The technician identifies the cause and cost; work starts after you approve.
Module replacement, line check, and re-linking the device to the ecosystem.
Warranty for the work performed and parts replaced.
The computer and laptop repair department in Almaty has 7 technicians with 6 to 15 years of experience.

The department has 7 specializations — they are listed on the technicians' cards.
experience10 yearsGraphics card repair technician
experience6 yearsPC and laptop diagnostics technician
experience8 yearsLaptop repair engineer
experience10 yearsSoftware installation specialist
experience7 yearsPC and laptop repair technician
experience13 yearsDiagnostics and virus removal specialist
experience15 yearsConsultant
We reply during working hours
Request smart home repair — a technician arrives within 60 minutes anywhere in the city, diagnostics are free.

Warranty question? Call us
+7 (775) 031 92 287 898 reviews of repairs at TECH SERVICE in total
Томирис Ж.Order No. ZK-2026/491 · 6 September 2026
oursДолго откладывал ремонт, потом всё-таки собрался. Ремонт камеры видеонаблюдения — вот с этим и пришёл. Больше всего напрягало: нет сигнала. Сергей Москоленко принял, посмотрел и сразу сказал, что делать. Приняли без очереди, оформили за пять минут. Вернули в тот же день, всё функционирует.
Тимур И.Order No. 665543 · 3 September 2026
oursПовод для визита: нет сигнала. Дамир М снял деталь, показал износ, вопросов не осталось. Проверили при мне, показали, что всё держит)
Елена К.Order No. 27491 · 25 June 2026
oursИскал мастерскую поближе к дому, чтобы не мотаться с техникой через полгорода. Ремонт шлагбаума — вот с этим и пришёл. Основная жалоба — ошибка. Мастер сразу сказал, что к чему, без размытых формулировок. Починили и дали гарантию на месяц.
Богдан С.Order No. TS-2610-431 · 28 May 2026
oursПоломка застала перед командировкой, тянуть было нельзя. Нужен был ремонт камеры видеонаблюдения — обратился сюда. Основная жалоба — запотела. Договорились на утро, к девяти уже был свободный мастер. Сравнивал с двумя другими — здесь вышло ровнее всех. Из деталей — матрица. Мастер опоздал на полчаса, правда позвонил. Проверил дома — всё на месте, ничего не забыли
Елдос К.Order No. 2026-5073 · 17 April 2026
oursБыло важно, чтобы сделали до выходных — гости, то-сё. Жалоба простая: нет сигнала. Даже настройки не сбились, что удивительно
Ерасыл Б.Order No. TS-2608-238 · 2 April 2026
oursБыло важно, чтобы сделали до выходных — гости, то-сё. Жалоба простая: не открываеться. Проверили при мне, показали, что всё держит
Айгерим Б.Order No. TS-4563 · 15 March 2026
oursПрочитал кучу отзывов, половина — реклама, но тут вроде живые. Повод для визита: нет сигнала. Вернули в тот же день, всё функционирует.
Айгерим Б.Order No. TS-2605-173 · 3 February 2026
oursБыло важно, чтобы сделали до выходных — гости, то-сё. Утром работало, днём сломалось, вечером я уже искал сервис. Жалоба простая: остановился. Сергей Москоленко снял деталь, показал износ, вопросов не осталось. В списке работ — привод. Мастер сам перезвонил, когда появилась запчасть. Сравнивал с двумя другими — здесь вышло ровнее всех. Включил, проверил, работает.
Динара М.Order No. TS-2505-422 · 28 December 2025
oursТехника кенеттен істен шықты, қатты асығыс едім. Мастер ақауды түсіндірді, қажетсіз нәрсе таңбады. Алдын ала айтқан уақыттан ерте бітірді. Нәтижесіне ризамын.
Сабина Г.Order No. 11969 · 14 December 2025
oursИскал мастерскую поближе к дому, чтобы не мотаться с техникой через полгорода. Повод для визита: ошибка. Сделали аккуратно, следов разборки не видно!!
Владимир Н.Order No. TS-2503-745 · 17 November 2025
oursКүтуге уақытым жоқ еді, сол күні алып кеттім. Ескі бөлшекті қайтарып берді, әдетте олай жасамайды. Бөлшектің бар-жоғын бірден тексерді, қоймада бар екен. Бағасын алдын ала келістік, соңында өзгерген жоқ. Жұмыс барысын көрсетіп отырды, жасырған жоқ. Ұсақ ақауларды да тегін жөндеп берді. Бір күнде жөндеп берді, кешіктірмеді. Мастер ақауды түсіндірді, қажетсіз нәрсе таңбады. Қайта жүгінсем, осында келемін.
Эльмира Т.Order No. ZK-9304 · 21 October 2025
oursТехника на гарантии уже не была, так что выбор был свободный. Симптом был очевидный: не встаёт на охрану. Все разъёмы на месте, ничего не люфтит.
Марина В.Order No. ZK-1746 · 24 July 2025
oursБұрын басқа сервиске барғанмын, бірақ бұл жолы осында келдім. Қарапайым ғана ақау деп ойладым, бірақ басқаша болып шықты. Тексеру кезінде бәрін өзі көрсетті. Ұсынамын, текке ақша алмайды!!
Диана М.Order No. ZK-2025/644 · 7 April 2025
oursРаботаю допоздна, поэтому нужен был сервис с нормальным графиком. До последнего откладывал, но пришлось признать: нет сигнала. Отдельно спасибо мастеру — Дамир М, терпения ему хватило. Посмотрели, назвали срок — два дня. Поставили новую деталь: объектив. Сказали 8 000, я согласился без торга. Хороший сервис, побольше бы таких. Сделали аккуратно, следов разборки не видно.
Бакыт Ж.Order No. ZK-2025/844 · 25 March 2025
oursПробовал найти мастера в своём районе, но все были заняты. Отдал мастеру: умный замок. Первое, что заметил: не держит заряд. Ответили быстро, не пришлось ждать на линии. Заплатил 25 000, и не жалею. Второй месяц — полёт нормальный)
Ержан А.Order No. TS-2509-880 · 25 February 2025
oursДо этого обращался в другой сервис, там только развели руками. Первое, что заметил: не держит заряд. Все разъёмы на месте, ничего не люфтит.
Томирис Ж.Order No. 889086 · 8 February 2025
oursБалалар бар, техникасыз қиын, сондықтан тез жөндеу керек еді. Бір айдан бері ешқандай мәселе жоқ.
Андрей П.Order No. ZK-8516 · 14 December 2024
oursПрочитал кучу отзывов, половина — реклама, но тут вроде живые. Основная жалоба — не поднимается. Работает как раньше, придирок нет.
Ерасыл Б.Order No. TS-2410-779 · 14 December 2024
oursБұрын осында ноутбук жөндеткенмін, сондықтан сеніммен келдім. Ескі бөлшекті қайтарып берді, әдетте олай жасамайды. Бір күнде жөндеп берді, кешіктірмеді. Қосымша бөлшек қажет болды, бірақ бағаны көтермеді. Ұсақ ақауларды да тегін жөндеп берді. Тексеру кезінде бәрін өзі көрсетті. Бағасын алдын ала келістік, соңында өзгерген жоқ. Жалпы әсер жақсы, кемшілік байқамадым!!
Данияр С.Order No. ZK-9313 · 22 September 2024
oursБольше всего напрягало: не встаёт на охрану. Сергей Москоленко возился с этим дольше, чем планировал, но довёл до конца. Включил, проверил, работает
Didn’t find the answer? Message us on WhatsApp.
Ask a questionSetup starts with connecting the hub to Wi-Fi and adding devices in the app. A technician will check compatibility, set up routines, and walk you through the controls. It depends on the model.
The difference is in the models: some have a screen and a Zigbee module, others only have a voice assistant. For a smart home, support for the right protocols matters, so check the specs.
If the device doesn't show up in the app and doesn't respond to a hub reboot, the sensor or its power is most likely the issue. A technician makes the final call after testing. It depends on the model.
Yes, smart switches and relays are repaired individually, there's no need to touch the whole system. The device is replaced entirely only when the board or relay can't be restored.
Check the power to the hub and router, reboot them one at a time, and see if the devices appear in the app. If some sensors still aren't visible, the communication module is probably damaged and needs repair.
Most likely the plug's internal relay is faulty or the contact in the power circuit is loose, so the command doesn't reach the load. This is a repairable component; a technician will check the relay and power. It depends on the model.
Tech Service repairs smart home systems in Almaty with its own technicians who have 4 to 20 years of experience. A technician arrives at your home within 60 minutes anywhere in the city, diagnostics are free, and there is a 1-year warranty on labor and parts. The price is quoted after diagnostics.
A smart home system doesn't break all at once—usually it's a chain of causes. Here's where to start when scenes stop triggering, connection is lost, or devices respond unreliably.
We recommend first checking the power to the hub and router, then the status of devices in the app, and only then calling a technician. Rebooting the controller and router one after the other resolves half of all calls—often the home comes back to life in a couple of minutes without a specialist. Next, open the app and see which devices are online and which have dropped off: if one out of ten sensors is missing, look for the cause in that sensor, not the whole system. Our technician arrives at your home anywhere in the city within 60 minutes, diagnostics are free, and the warranty on labor and parts is 1 year. At Tech Service, the on-site specialist starts by checking power and network, not by taking equipment apart. If some devices come back after rebooting the hub and some don't, the problem isn't the power supply as a whole but specific nodes—this saves diagnostic time.
If the connection drops regularly and repeats after a reboot, it's a sign of a hardware problem with the hub or interference in the channel, not a one-time network glitch. A single loss of connection during a power surge is normal, but repeated dropouts every few hours indicate module overheating, a weak power supply, or a congested frequency band. On a dual-band router, a 2.4 GHz hub often conflicts with neighboring networks and the microwave—switching to a free channel eliminates some of the dropouts. It helps to log periodic connection losses by time: a pattern like 'every evening' or 'when the appliance turns on' tells the technician where to look. The event log in the app shows which device dropped off first, and that narrows down the causes for the on-site specialist.
The hub is the brain of the smart home system, and most calls to us come down to it one way or another. Here's what complaints like 'not responding,' 'won't connect,' and 'freezes' actually mean in practice.
A hub that won't connect to Wi-Fi usually needs the communication module checked and reflashed, not just re-entering the network password. During diagnostics, the technician first makes sure the router is handing out addresses and isn't blocking the device via MAC filter, then checks the smart home module itself for overheating and oxidized contacts, and after that — the firmware version and compatibility with the current network. A common picture: the hub is fine, but the access point operates on a band the module doesn't support, or on a channel with heavy load from neighboring networks. If the device sees other networks but not yours, the cause may be the router's band or channel — this is checked on site in a couple of minutes. A stable connection only holds with coordinated router and hub settings, so after the work we ask you not to change network parameters without checking.
We fix regular hub freezes by diagnosing the power supply and checking the module — a one-time reboot doesn't solve the problem. On site, the technician measures the voltage in the line, inspects the power supply and the breaker the control panel is connected to, and checks the event log: it shows the moment the device goes into reboot again. The cause is often a voltage drop when powerful appliances start — an air conditioner, boiler, or pump — or overheating of the case due to tight installation in the panel or niche. Firmware can also cause failures: after an update, some scenarios may cyclically restart the controller. If freezes coincide with network load peaks or with switching on powerful appliances, it's worth checking power stability, not just the hub itself. Our technicians have worked with such systems for 4 to 20 years and can tell a power failure from a board failure by the first measurements.
An error on the display or in the app while devices are working usually means a failure of one node or a status desync, not a failure of the whole system. The control panel shows a code, the app duplicates it in the devices section, and that code shows which module stopped communicating: a sensor, a relay, or the hub itself. Desync happens when a command is sent but no confirmation comes back, and the status in the app gets stuck on the old value even though the light or valve has already responded. Diagnostics are free, so the technician comes and checks each node's connection one by one without waiting for the error to repeat. It's worth photographing the error code before rebooting — after a reset it may disappear, and the code helps the technician identify the node faster. We provide a 1-year warranty on labor and parts.
Smart home actuators fail in different ways: some lose connection, others jam mechanically. Below is what can actually be restored and what is easier to replace, and by what signs the technician determines this.
When the leak sensor triggers but the smart valve doesn't shut off the water, we check the chain 'sensor → hub → valve' because the failure can be in any link. The electric valve on the pipe receives a command from the controller, and the controller receives a radio signal from the sensor; a break in this chain creates a false sense of security. During diagnostics, the technician removes the actuator and checks whether the stem moves on a manual command, whether a signal reaches the terminals, and whether the central module sees the sensor in the device list. Often the culprit is a dead battery: the signal is sent but too weak to be received. If the sensor sends a signal but the valve stays silent, the cause is more often the valve actuator or the controller losing the command, not the sensor itself — so starting with the valve rather than replacing the sensor is faster and cheaper in labor.
When a smart plug shows up in the app but doesn't power the load, we check the relay and contact group—often the issue is there, not in the connection. The app shows the device online, the command reaches the module, but the contacts inside don't close: the actuator clicks idly or stays silent. The technician measures voltage at the output terminals when a command is sent and compares it with the mains voltage—a discrepancy points to a burnt contact group or a stuck switch. The load is checked separately: a powerful appliance could have overloaded the plug, and then melted contacts are visible. If the plug is 'visible' but doesn't click on command, it indicates a failed switch; if it clicks but the appliance doesn't work, check the load and wiring. In my opinion, a burnt contact group shouldn't be restored: the unit has already worked under load and will fail again.
| Device | What we check | Repair or replacement |
|---|---|---|
| Hub and controller | power, communication module, firmware | repair by unit |
| Smart valve | actuator, valve, command from hub | actuator repair |
| Smart plug | relay, contact group | usually replacement |
| Leak sensor | battery, signal | replacement on failure |
| Door/window sensor | magnet, battery | replacement on failure |
Not every 'breakdown' requires service intervention: some smart home failures are fixed by reconfiguration. We explain how to tell one from the other and what exactly the technician does on site.
After a power outage, we restore automation and check that the hub and devices have synced again. In our practice, lighting schedules and climate settings most often get lost: the controller boots with an empty list, and sensors remain in 'no connection' status even though they're physically fine. The technician verifies each device's binding to the hub, re-enters trigger conditions, and checks command delivery to actuators—relays, valves, plugs. If automation fails with every power fluctuation, the cause may be in the hub's power-loss settings: it's worth checking so the failure doesn't repeat at the next outage. Restoring scenarios takes less time than a service visit and doesn't require replacing parts.
We start smart home restoration in Almaty with a specialist visit. Some work is done right on site, and if a specific component needs repair, the equipment is taken to the service center.
We come to your home and run diagnostics on site: we check the hub, connection, and devices. If a component needs repair, the equipment is taken to the service center rather than replaced blindly. The on-site specialist first identifies exactly what stopped working — the controller, the smart home module, or a specific sensor — and only then decides whether to fix it on site or take it to the workshop. We perform smart home repair in Almaty both on site and in the service center — the format depends on what exactly failed. Diagnostics are free, so the cause of the breakdown becomes clear before any work begins. Most connectivity and configuration tasks are handled on site: reconnecting the hub, checking channels, restoring scenarios after a power failure. Restoring boards and modules requires service conditions — soldering, load testing, bench tests — and the specialist will tell you about this after diagnostics, not guess over the phone. For the owner, this means the decision on the format is made based on the actual check, not on a description of symptoms.
On-site diagnostics are free and take as long as needed to check the hub, connection, and devices. The on-site specialist arrives within 60 minutes anywhere in the city. The check usually fits into one visit: first, a conversation about what stopped working and when, then an inspection of the controller and power supply, then a test of the connection between the hub and devices, and a check of scenarios and sensors. Based on the results, the specialist states the cause and the format of work — on site or in the service center. The more precisely you describe what stopped working and under what conditions it happened, the faster diagnostics will go: an accurate symptom saves time for both you and the specialist. If the fault is intermittent, it helps to recall what preceded it — power outages, a router replacement, moving furniture, or new devices on the network.
Smart home restoration is handled by a service specialist, not an installer: the installer mounts the system, while diagnostics and restoration are done by a repair technician. The difference is in the task: the installer knows how cables are routed and where modules are located, but does not always work with boards, firmware, and connection restoration. The repair specialist starts by finding the cause — power, communication channel, controller, sensor — and brings the system back to working order. Contacting the installer makes sense only if the system is under installation warranty: then they are responsible for their work. In other cases, restoration is performed by the party responsible for the result. The direct contractor comes personally rather than passing the request to a subcontractor, so one party is responsible for diagnostics and restoration, and you don't have to retell the breakdown story to multiple people.
Below are the key terms: what the warranty covers, how diagnostics work, and how to order a visit, so you understand what work the service is responsible for.
We provide a 1-year warranty on labor and parts — this covers both controller restoration and sensor replacement. The term is the same for any system component: whether the technician restores the control board, replaces a leak sensor or a valve actuator, the same condition applies to each item. Over years of practice in the Almaty market, we've seen that components last longer when, after restoration, we check power and radio channel stability, not just swap the part. That's why in our work, checking communication and power is part of every visit — it reduces the risk of the same component failing again. The warranty covers the work performed and the parts installed, so it's important to keep records of which component was serviced and which parts were replaced: with them, the technician can identify the cause faster on a repeat call.
Diagnostics are free with us, and the technician quotes the cost of work after diagnostics — when the scope of tasks is clear. First, they check the controller, power, radio channel and sensor statuses in the app, then explain the cause of the failure and list the operations needed. This approach protects you from paying blindly: you agree to the work only knowing the cause and the list of operations. Based on our experience, some calls are resolved by reconfiguring scenarios or replacing a single sensor, and the free check shows this right away — without taking the whole system apart. We accept Kaspi QR, Kaspi Red, card, cash or bank transfer for companies, so you can pay in the way that's convenient after agreeing on the work with the technician. If, after the check, the work doesn't suit you, you pay only for what was actually done — the diagnostics themselves remain free.
A smart home system rarely breaks down entirely — more often one component fails or the scenario logic gets disrupted. Below is a short summary to help you decide before calling a technician.
9brands
Choose an ecosystem or device manufacturer to go to the brand page and check compatibility.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your laptop screen is broken, turn the device off first, don't press on the display, and check the picture through an external monitor.
12 March 2026 · 11 minutes read
If your laptop freezes, the first thing to do is restart it and check Task Manager to see what's loading the CPU and memory.
25 January 2026 · 12 minutes read
If your computer won't turn on, start simple: check the outlet, power cable, switch on the power supply, and the power button.
19 January 2026 · 13 minutes read
If your laptop won't boot, first determine which of two states you're in: the device doesn't respond to the power button at all…
13 December 2025 · 12 minutes read












