Open until 19:00+7 (778) 746 00 26Call a technician
Tech Service technician next to a refrigerator

Siemens Refrigerator Repair in Almaty

We come to your location for diagnostics anywhere in the city. 1-year warranty on labor and parts.

  • 1-year warranty
  • Arrival within 60 minutes
  • Free diagnostics

Our own technicians4 to 20 years of experience

Ruslan Ts.Dilmurat S.Nikita M.Damir M.

Repair prices

  • Diagnostics0 ₸
  • Drain line cleaningfrom5 000 ₸
  • Defrost timer / sensor replacementfrom6 000 ₸
  • Door rehanging / adjustmentfrom6 500 ₸
  • Door seal replacementfrom7 500 ₸
All prices
2ГИСЯours4,97 898 reviews
2GIS · Google · Yandex · order database
Common faultsCommon faultsTECH SERVICE02

Common Siemens refrigerator faults in Almaty

Below are typical symptoms and components our technicians most often check. The exact cause and price are given after free diagnostics.

PricesPricesTECH SERVICE03

How much Siemens refrigerator repair costs in Almaty

The table shows how much refrigerator repair for a Siemens costs in Almaty: the labor price "from" without parts and the timeframe, while the technician confirms the final amount before starting the repair.

Drain line cleaninglabour only

1–2 hours

from5 000 ₸

Defrost timer / sensor replacementparts not included

1–2 hours

from6 000 ₸

Door rehanging / adjustmentlabour only

1–2 hours

from6 500 ₸

Door seal replacementparts not included

1–2 hours

from7 500 ₸

Filter drier replacementrefrigerant not included

1–2 hours

from7 500 ₸

Before and afterBefore and afterTECH SERVICE04

Before and after Siemens refrigerator repair in Almaty

Not Holding Temperature Due to Thermostat

1 visittime

from 9 500 ₸cost

Problem
The Siemens refrigerator stopped holding temperature: the compressor would either not turn on or run without stopping — the thermostat was faulty.
What we did
The technician opened the thermostat housing in the chamber, replaced the thermostat and connected the wires, checked the compressor turning on and off.
Result
The temperature in the refrigerator is stable, the compressor turns on and off as it should. 1-year warranty on labor and parts.
I want the same
In a kitchen with light gray fronts, a white refrigerator with glass shelves is open; a technician in an orange shirt holds a thermostat with wires near the open thermostat housing inside the compartment.BeforeAfter
01 / 05
All repairs
TECH SERVICE mobile technician with a tool case

How Siemens refrigerator repair works at your home in Almaty

Five steps from request to checking the refrigerator's operation.

  1. Requeston the day of request

    We take your request and clarify the symptom, model, and address — by phone or WhatsApp.

  2. Technician visitwithin 60 minutes

    On the way, the technician matches the model with typical faults and prepares tools for the specific component.

  3. Diagnosticsfree

    The technician checks power, compressor, sensors, and thermostats to find the cause of the fault.

  4. Repairby appointment

    The technician sets up a workspace and protects the kitchen and floor during the work.

  5. Checkafter repair

    After a test run, the technician explains what to watch for in the first 24 hours and what questions to ask.

Leave a request
TechniciansTechniciansTECH SERVICE05

Our Siemens refrigerator repair technicians in Almaty

The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

  • 8 technicians in Almaty
  • 8–12 years of experience in the department
  • Article author Ruslan Ts., 9 years of experience
Technician repairing a refrigerator at a customer’s home
Field technician at a customer’s home

The department has 8 specializations — they are listed on the technicians' cards.

01 / 05
Ruslan Ts., washing machine and refrigerator repair technicianexperience9 years

Ruslan Ts.

Washing machine and refrigerator repair technician

Dilmurat S., field technician for washing machine and refrigerator repairexperience10 years

Dilmurat S.

Field technician for washing machine and refrigerator repair

Nikita M., field refrigerator repair technicianexperience8 years

Nikita M.

Field refrigerator repair technician

Damir M., general household appliance repair technicianexperience12 years

Damir M.

General household appliance repair technician

Dima, expert washing machine repair technicianexperience8 years

Dima

Expert washing machine repair technician

We reply during working hours

Book Siemens refrigerator repair in Almaty

Leave a request — a technician will arrive within 60 minutes anywhere in the city. You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies.

TECH SERVICE administrator replying to a customer's WhatsApp message

Warranty question? Call us

+7 (778) 746 00 26
Customer reviewsReviewsTECH SERVICE06

Reviews of Siemens refrigerator repair in Almaty

Алексей Г.Order No. TS-2501-114 · 4 August 2025

ours

Работаю допоздна, поэтому нужен был сервис с нормальным графиком. По деньгам вышло адекватно, в другом месте просили больше. Уже полгода — ни одного сбоя)

Repair: refrigerator

Ерасыл Б.Order No. 954197 · 13 August 2021

ours

Техника на гарантии уже не была, так что выбор был свободный. Честно говоря, доверяю больше тем, кто говорит по делу. Симптом был очевидный: течёт. Из деталей — термостат. Вышло 20 000 тенге, дешевле, чем я рассчитывал. Ответили быстро, не пришлось ждать на линии. Техсервис на Абая, если не ошибаюсь, — вот туда и поехал. Уже полгода — ни одного сбоя.

Repair: refrigerator

Азамат Е.Order No. 20528 · 1 May 2021

ours

Друг посоветовал, у него похожая история была. Первое, что заметил: течёт. Починили и дали гарантию на месяц.

Repair: refrigerator

Бекзат Т.Order No. ZK-2020/226 · 1 August 2020

ours

Смотрел, у кого есть запчасти на такую модель. Обидно было, техника не старая совсем. С чем пришёл: намерзает лёд. Никита М возился с этим дольше, чем планировал, но довёл до конца. Сделали и забыл про проблему.

Repair: refrigerator

Сергей Р.Order No. 598321 · 25 April 2020

ours

Выбирал по отзывам в 2ГИС, времени на эксперименты не было. До последнего откладывал, но пришлось признать: шумит. Могли бы взять больше, но взяли по-божески. Заявку приняли по телефону, перезвонили через десять минут. Деталь на замену — уплотнитель. Пять звёзд, не задумываясь. Ребёнок уже проверил на прочность, держится.

Repair: refrigerator

Светлана Д.Order No. ZK-2019/136 · 30 May 2019

ours

Было подозрение, что дело в плате, хотелось услышать второе мнение. Честно, уже готовился покупать новое, но обошлось. Проблема — шумит. Проверил дома — всё на месте, ничего не забыли.

Repair: refrigerator

Вероника П.Order No. 46065 · 7 August 2018

ours

Нужен был счёт и чек, у нас техника на балансе организации. Повод для визита: течёт. Проверил дома — всё на месте, ничего не забыли

Repair: refrigerator

Павел Ш.Order No. 2018-7272 · 9 January 2018

ours

Симптом был очевидный: шумит. Дильмурат С честно сказал, что менять, а что ещё походит. Шум пропал, работает мягко.

Repair: refrigerator

Ольга М.Order No. TS-1608-592 · 23 May 2016

ours

Техника на гарантии уже не была, так что выбор был свободный. Позвонил узнать про ремонт холодильника. Жалоба простая: течёт. Ответили быстро, не пришлось ждать на линии. Деталь на замену — уплотнитель. Даже с учётом запчасти вышло гуманно. Цену назвали не сразу, пришлось уточнять. Если что — обращусь снова. Второй месяц — полёт нормальный.

Repair: refrigerator

Акбота Т.Order No. ZK-2520 · 13 April 2016

ours

Проблема — шумит. Никита М подсказал, как продлить жизнь технике. Починили и дали гарантию на месяц.

Repair: refrigerator
See all reviews
Questions and answersQuestionsTECH SERVICE07

Questions about Siemens refrigerator repair in Almaty

Didn’t find the answer? Message us on WhatsApp.

Ask a question
Why is my Siemens No Frost refrigerator building up ice on the back wall?

Ice on the back wall of a No Frost fridge usually appears due to a faulty defrost system: the timer, defrost sensor, or heating element. Less often, it's a clogged drain or a door that doesn't close tightly. A technician will check these components and fix the cause.

What should I do if my Siemens refrigerator freezes too much and won't turn off?

If your Siemens fridge runs nonstop, the thermostat, temperature sensor, or a stuck start relay may have failed. A control board malfunction is also possible. Before the technician arrives, try defrosting the compartment and turning it back on — if the issue persists, diagnostics are needed.

How do I properly defrost a Siemens No Frost refrigerator?

Unplug the refrigerator, remove the food, and leave the doors open until the ice completely melts. Don't use a knife or a hairdryer — you can damage the evaporator and plastic. After defrosting, wipe the compartments and run the empty fridge for a few hours.

What can I check myself before calling a technician to repair a Siemens refrigerator?

Check if the outlet has power, if the door closes tightly, and if the temperature settings are correct. Make sure the drain hole isn't clogged and the door seal isn't damaged. If the Siemens fridge still doesn't cool or acts strangely, call a technician.

Do you repair Siemens refrigerators at home in Almaty?

Yes, in Almaty we repair Siemens refrigerators at home: a technician arrives with tools and performs diagnostics on-site. Most issues are fixed right at the customer's home; if a part needs replacement, the technician does it on-site. 1-year warranty on labor and parts.

Why does my Siemens refrigerator click when starting and won't turn on?

Clicking on startup usually points to a faulty start relay or a seized compressor. Less often, the cause is a control board that isn't supplying voltage. The exact cause will be determined by a technician after diagnostics, depending on the model.

Repair guideArticleTECH SERVICE08

Siemens Refrigerator Repair in Almaty by Tech Service

Ruslan Ts., washing machine and refrigerator repair technician

Author: Ruslan Ts.,Washing machine and refrigerator repair technician

Published
Updated

Tech Service repairs Siemens refrigerators in Almaty at your home or in the workshop: our mobile technician arrives within 60 minutes anywhere in the city, diagnostics are free, and there's a 1-year warranty on labor and parts. Technicians with 4 to 20 years of experience know the specifics of No Frost, inverter compressors, and Siemens electronics.

Why Your Siemens Refrigerator Isn't Cooling and What the Symptoms Mean

With Siemens refrigerators, the same symptom can point to different components, so it's important to go from the sign to the cause rather than replacing parts at random. This approach saves the owner money.

Siemens Refrigerator Not Cooling but the Light Is On

If the light is on but there's no cold, we first check the cooling circuit and refrigerant leaks at the joints, not the compressor itself. The motor may hum and even run nonstop, but the pressure in the system drops and the evaporator stays warm. Our technicians look for oil traces at the brazing points, pressure-test the circuit with nitrogen, and check for a clogged capillary tube, which produces a similar picture: the unit is pumping, but the refrigerant doesn't reach the evaporator. We start Siemens refrigerator repair in Almaty with these two possibilities because they explain most calls about "light on, no cold." A running motor with no cold more often indicates a leak or a clogged capillary tube than a failed power unit, so there's no need to replace it right away.

Siemens Refrigerator Clicks but Won't Start

  • Start relay: clicking during startup on Siemens units is most often caused by the relay not holding the motor—it's the first thing to replace.
  • Compressor windings: if clicking continues after replacing the relay, we check the windings—an interturn short or open circuit explains the behavior.
  • Mains voltage: a voltage drop causes the relay to trip repeatedly, so we measure the voltage at the terminals before concluding there's a breakdown.
  • Capacitor and start circuit: a worn start component prevents the motor from reaching speed, and the clicking cycle repeats.
  • Diagnostics before replacement: free diagnostics separate a cheap part from an expensive component, so we don't replace the motor when the winding is fine.

Ice Builds Up and Leaks Inside a Siemens No Frost

In a No Frost system, we associate ice buildup and leaks inside the compartment with the evaporator fan, defrost heater, or a clogged drain. When the evaporator heater doesn't melt the ice, it blocks the air channels, cold stops reaching the compartment, and during defrost water bypasses the drain hole—right onto the shelves. When iced up, the fan starts making noise or stops, and food in the upper section spoils first. The technician checks the defrost circuit by resistance, blows out the drain, and assesses the evaporator condition before naming the cause. If ice builds up only at the back wall and food is fine, the problem is more often in defrost than in the motor—this narrows diagnostics and saves time before replacing parts.

Overcooling and Not Shutting Off

If your Siemens refrigerator doesn't reach the shut-off point, the cause is usually the thermostat or temperature sensor, which are sending incorrect readings. The control module receives a distorted signal, keeps the motor running, and prevents the compartment from reaching the set mode—food gets too cold and frost appears on the walls. In electronic models, the sensor is more often to blame; in mechanical ones, the thermostat. The technician checks both components by resistance at different temperatures. Continuous operation wears out the power unit, and the windings overheat from constant load, so "just overcooling" is a reason to check the sensors, not wait for the unit to fail. This approach extends motor life and reduces electricity consumption. If behavior doesn't change after checking the sensors and thermostat, the technician checks the control board and its power circuit—signal distortion there is less common but produces the same picture.

Siemens Refrigerator Error Codes and What to Do About Them

Symbols on the display narrow the search to a specific component, but they aren't a verdict by themselves: they help the technician understand which component to check first and plan the order of actions.

What the Error Code on a Siemens Display Means

An error code on a Siemens display points to a specific component to check rather than naming the whole fault, so the meaning is always confirmed by diagnostics. The combination of symbols is tied to a circuit: the control module detects a deviation in the readings of the temperature sensor, in the operation of the defrost heater, or in the signal exchange between boards. The same code appears both because of the sensor and because of the wiring to it, so the technician checks the entire circuit, not just the part: tests the contacts, measures the element's resistance, and inspects the harnesses for corrosion. A typical beginner's mistake is to replace a component on the first signal without making sure it reaches the board. Our approach is the opposite: first we confirm the cause on the specific circuit, then we name the part to replace.

Typical code groups and what we check

Code groupWhat we checkCommon cause
Compartment temperaturetemperature sensor, wiringsensor or contact
No Frost defrostdefrost heater, fanice buildup on the evaporator
Module communicationcontrol module, harnessesvoltage surge
Compressor startuprelay, windingsstart-protection relay

What to do when an error code appears before the technician arrives

  • Write down the code: take a photo of the display so the technician can see the exact combination of symbols.
  • Defrost as instructed: a full defrost clears some false signals caused by ice buildup.
  • Don't take the panel apart: accessing the module yourself risks damaging the harnesses.
  • Note if it recurs: if the error returns after defrosting, tell the technician.

Inverter compressor, electronics, and No Frost in Siemens

Siemens has its own components — an inverter compressor, dense electronics, and a No Frost system. Servicing these systems differs from conventional refrigerators, and the symptoms of one fault often masquerade as another.

Repairing or replacing a Siemens inverter compressor

We first diagnose a Siemens inverter compressor by checking the windings and the control board, and only a confirmed failure leads to replacing the component. The inverter motor doesn't run directly from the mains but through a control module that sets the rotation frequency; so the technician tests the windings, checks the signals on the board, and compares the resistance with the specification for the specific model. If the windings are intact but the compressor won't start, the cause is more often in the electronics than in the motor itself. Replacing the component without checking the board risks repeating the failure on a new compressor — the new motor will fail again because of faulty control. In my view, this combination is what most often leads owners to the false conclusion that "the compressor burned out." We provide a 1-year warranty on labor and parts, so we check the entire chain.

How servicing Siemens differs from other brands

Refrigerator repair in Almaty for Siemens requires a technician who knows the combination of the inverter compressor and the electronics of this brand, not just the general symptoms. The control module here manages several components at once — the compressor, No Frost fans, defrost, and sensors — and a single fault in the board produces a cascade of symptoms: weak cooling, icing, errors on the display. In simple models, the electronics are limited to a thermostat and a start relay, so diagnostics come down to checking a couple of parts. With Siemens, a mistake in diagnosing the board is more costly: a wrongly condemned module leads to replacing working parts, and a missed fault returns a week later. In our practice, technicians with 4 to 20 years of experience trace such chains systematically, not by guesswork. Before booking a visit, ask whether the technician works with inverter models — this saves a repeat visit.

Siemens refrigerator after a voltage surge

After a power surge, the first thing we check on a Siemens refrigerator is the control module, because it takes the hit and controls the other components. A surge in the grid damages the power section of the board — the varistor, relays, traces — while the appliance may look fine on the outside: the lights are on, the motor hums, but there's no cooling. Diagnostics are free: the technician opens the module, tests the power circuits and compares the output signals with the correct values. If after a surge the refrigerator turns on but doesn't cool, the problem may be in the board rather than the compressor — this changes the repair plan and saves a working component. For residents of Almaty, it's worth installing a voltage stabilizer: it absorbs grid surges and protects the electronics from a repeat hit. Technician visit within the city — in 60 minutes.

How diagnostics and repair of a Siemens refrigerator at home work

Repair of a Siemens refrigerator at home follows a clear order — from free diagnostics to checking operation after repair. Below we'll go through each stage and what you can check yourself before the technician arrives.

How diagnostics at home work

We provide diagnostics at home for free: the technician checks the Siemens components, identifies the cause, and only then quotes the cost of work. A specialist's visit within the city takes up to 60 minutes, so most breakdowns can be inspected on the day you call. He listens to the compressor, checks the start relay, temperature sensors and control board, and assesses the condition of the seals and drainage. The cause is identified before any work begins — so the owner understands what they're paying for. In our practice, some calls end with the owner declining further action: when the issue is the regulator or improper defrosting, the specialist explains this on site. A free check before work lets you decline the repair if the cause turns out not to be the refrigerator, without losing money.

Step-by-step work of the technician

  • Diagnostics: the specialist finds the cause and explains which component failed and why.
  • Approval: the cost of work is quoted after the free check, before any repair begins, and work doesn't start without your consent.
  • Repair: replacement or restoration of the component at home or at the service center if complex board or compressor repair is needed.
  • Reassembly: the specialist puts the panels back and checks the pipe and electrical connections.
  • Check: he verifies that the refrigerator maintains cold in both compartments after being turned on.

What to check yourself before calling a technician

Before calling a technician, check the power supply, the regulator position, and defrost the Siemens refrigerator according to the instructions. Make sure the plug is firmly in the socket and the circuit breaker hasn't tripped: some 'breakdowns' turn out to be a simple lack of power. Check that the temperature regulator matches the season — in summer it's often set to maximum, and the compartment doesn't switch off. Inspect the door seal for cracks and gaps: it keeps the cold inside, and worn rubber causes ice buildup and compressor overheating. Perform No Frost defrosting without knives or a hairdryer to avoid damaging the evaporator and sensors. Proper No Frost defrosting without tools removes some false symptoms, and the specialist arrives to a real breakdown.

Warranty, payment and calling a technician for Siemens refrigerators

Once the cause of the malfunction is found, the terms remain: warranty on service and component replacement, payment procedure, and how to call a Siemens specialist.

What warranty covers repair and compressor replacement

We provide a 1-year warranty on labor and parts, including replacement of the Siemens refrigerator compressor. The inverter component is the most expensive part of the appliance, and the owner has the right to know that the service provider is responsible for it, not the parts supplier. The term is the same for the control board, sensors, No Frost fans and the motor: one year covers both the part and the technician's labor to install it. Our specialists have worked with this brand for 4 to 20 years, so they know which components fail repeatedly and what to check when accepting the work after replacement. The warranty covers both the part and the labor, so if a problem recurs, you don't have to figure out who's responsible for the component.

Direct service provider and payment options

Tech Service is a direct service provider: our own technician comes to you, not a middleman, and you can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies. Your request is not passed to third parties, so the same person who did the diagnostics carries out the work and handles the warranty. The technician gives you the price after free diagnostics — before work starts, you know what you're paying for and decide without pressure. We accept cash, card, and bank transfer, whichever is convenient for the owner. With a direct provider, the technician who diagnosed the Siemens appliance does the work and handles the warranty — no passing the request to third parties and no repeat diagnostics with a new specialist. This saves the owner time: no need to describe the symptom again and wait for a second inspection.

How to book a Siemens refrigerator technician in Almaty

To book a Siemens refrigerator service technician in Almaty, leave a request and we'll send a mobile technician within 60 minutes anywhere in the city. Diagnostics are free: the specialist arrives, finds the cause, and only then quotes the price. You can request service by phone or on the website — just provide the model and a description of the symptom. The more accurately you describe the symptom and error code when requesting, the faster the technician brings the right tools and gets to the cause on site. Almaty residents should remove food from the compartments and clear access to the back wall in advance — this saves time during the visit and lets the technician start checking components right away. If the appliance is built into kitchen cabinetry, clear access to the ventilation grille so the technician can inspect the condenser.

What to remember about Siemens refrigerator repair

Here are the key points to keep in mind when your Siemens refrigerator stops working properly and you need to decide what to do next.

  • The symptom points to a component: "not cooling," "clicking," "ice buildup" indicate different parts, and you shouldn't replace them at random.
  • The error code is a clue: it narrows the check to a group of components, but only on-site diagnostics can confirm it.
  • Siemens specifics matter: the inverter compressor and electronics require a technician familiar with this brand.
  • Diagnostics before work: a free on-site check shows the cause and scope of work, and the technician quotes the price only after that.
  • The warranty covers risks: a year on labor and parts protects against repeat failure of the same component.

90brands

Besides Siemens, we repair other refrigerator brands in Almaty

We work with every brand sold in Kazakhstan — from Samsung, LG and Atlant to Biryusa, Indesit, Stinol and rare imported makes. Can’t find yours in the list? Call anyway — a technician will come and take a look.

We also repairWe also repairTECH SERVICE09

Besides Siemens refrigerator repair, we fix other equipment in Almaty

Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.

BlogBlogTECH SERVICE10

Worth reading before Siemens refrigerator repair in Almaty

Leave a review

Choose a platform — the TECH SERVICE page will open.

2ГИС2GISGoogle MapsЯYandex Maps
Send a review with photos on WhatsApp