Open until 19:00+7 (778) 746 00 26Call a technician
Tech Service technician next to a refrigerator

Hansa Refrigerator Repair in Almaty

A technician will arrive within 60 minutes anywhere in the city. Free diagnostics, 1-year warranty on labor and parts.

  • 1-year warranty
  • Arrival within 60 minutes
  • 4 to 20 years of experience

Our own technicians4 to 20 years of experience

Ruslan Ts.Dilmurat S.Nikita M.Damir M.

Repair prices

  • Diagnostics0 ₸
  • Drain line cleaningfrom5 000 ₸
  • Defrost timer / sensor replacementfrom6 000 ₸
  • Door rehanging / adjustmentfrom6 500 ₸
  • Door seal replacementfrom7 500 ₸
All prices
2ГИСЯours4,97 898 reviews
2GIS · Google · Yandex · order database
Common faultsCommon faultsTECH SERVICE02

Common Hansa refrigerator faults in Almaty

Common symptoms of Hansa refrigerator malfunctions and their likely causes — from refrigerant leaks to electronic failures.

PricesPricesTECH SERVICE03

How much Hansa refrigerator repair costs in Almaty

The table shows how much refrigerator repair costs for a Hansa in Almaty: the labor price "from" without parts and the time it takes; the technician confirms the final amount before starting the repair.

Drain line cleaninglabour only

1–2 hours

from5 000 ₸

Defrost timer / sensor replacementparts not included

1–2 hours

from6 000 ₸

Door rehanging / adjustmentlabour only

1–2 hours

from6 500 ₸

Door seal replacementparts not included

1–2 hours

from7 500 ₸

Filter drier replacementrefrigerant not included

1–2 hours

from7 500 ₸

Before and afterBefore and afterTECH SERVICE04

Before and after Hansa refrigerator repair in Almaty

Not holding temperature due to thermostat

1 visittime

from 9,500 ₸cost

Problem
The Hansa refrigerator stopped holding temperature: the compressor either would not turn on or ran without stopping — the thermostat is faulty.
What we did
The technician opened the thermostat housing in the chamber, replaced the thermostat and connected the wires, and checked the compressor turning on and off.
Result
The compressor turns on and off according to the set temperature, and the refrigerator holds cold again.
I want the same
In a kitchen with light gray fronts, a white refrigerator with glass shelves is open; a technician in an orange shirt holds a thermostat with wires near the open thermostat housing inside the compartment.BeforeAfter
01 / 05
All repairs
TECH SERVICE mobile technician with a tool case

How Hansa refrigerator repair works at your home in Almaty

Five steps from request to performance check.

  1. Requestsame day

    Submit a request and a technician will arrive within 60 minutes anywhere in the city.

  2. Diagnosticsfree

    The technician will identify the cause of the malfunction and determine the scope of work needed.

  3. Approvalafter inspection

    The technician will agree on the list of work with you before starting, so you can make a decision.

  4. Repairafter approval

    The necessary work is performed with replacement parts compatible with your model.

  5. Time confirmationbefore arrival

    The technician confirms a convenient time slot and clarifies what needs to be cleared around the refrigerator.

Leave a request
TechniciansTechniciansTECH SERVICE05

Our Hansa refrigerator repair technicians in Almaty

The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

  • 8 technicians in Almaty
  • 8–12 years of experience in the department
  • Article author Ruslan Ts., 9 years of experience
Technician repairing a refrigerator at a customer’s home
Field technician at a customer’s home

The department has 8 specializations — they are listed on the technicians' cards.

01 / 05
Ruslan Ts., washing machine and refrigerator repair technicianexperience9 years

Ruslan Ts.

Washing machine and refrigerator repair technician

Dilmurat S., field technician for washing machine and refrigerator repairexperience10 years

Dilmurat S.

Field technician for washing machine and refrigerator repair

Nikita M., field refrigerator repair technicianexperience8 years

Nikita M.

Field refrigerator repair technician

Damir M., general household appliance repair technicianexperience12 years

Damir M.

General household appliance repair technician

Dima, expert washing machine repair technicianexperience8 years

Dima

Expert washing machine repair technician

We reply during working hours

Book Hansa refrigerator repair in Almaty

Choose a convenient arrival time and confirm your request — the technician will coordinate the visit. 1-year warranty on labor and parts.

TECH SERVICE administrator replying to a customer's WhatsApp message

Warranty question? Call us

+7 (778) 746 00 26
Customer reviewsReviewsTECH SERVICE06

Reviews of Hansa refrigerator repair in Almaty

Ксения И.Order No. TS-2612-282 · 29 August 2026

ours

Хотел сначала вызвать мастера на дом, потом передумал. Первое, что заметил: намерзает лёд. Никита М взялся за то, от чего другие отказались. Гудит ровно, не греется, всё как надо

Repair: refrigerator

Мирас С.Order No. TS-2641 · 13 July 2026

ours

Проблема — течёт. Отдельно спосибо мастеру — Никита М, терпения ему хватило. Сделали и забыл про проблему.

Repair: refrigerator

Индира П.Order No. ZK-1617 · 20 September 2024

ours

Хотел сначала вызвать мастера на дом, потом передумал. Техсервис на Абая, если не ошибаюсь, — вот туда и поехал. Проверили на всех режимах, всё чётко!!

Repair: refrigerator

Юлия А.Order No. TS-5126 · 17 April 2023

ours

Пробовал найти мастера в своём районе, но все были заняты. Утром столкнулся с тем, что течёт. Позвонил, описал проблему, сказали привозить — посмотрят в тот же день. Вышло дешевле нового, что логично. Из деталей — компрессор. Хороший сервис, побольше бы таких. Работает как раньше, придирок нет.

Repair: refrigerator

Аружан К.Order No. ZK-2416 · 24 February 2023

ours

До этого обращался в другой сервис, там только развели руками. Проблема — не морозит. Проверили при мне, показали, что всё держит.

Repair: refrigerator

Данияр С.Order No. TS-2205-673 · 5 April 2022

ours

Друг посоветовал, у него похожая история была. С чем пришёл: не морозит. Проверили при мне, показали, что всё держит.

Repair: refrigerator

Алексей Г.Order No. TS-4782 · 30 August 2021

ours

Было подозрение, что дело в плате, хотелось услышать второе мнение. Приехал из командировки, а дома — шумит. В списке работ — уплотнитель. Проверил дома — всё на месте, ничего не забыли

Repair: refrigerator

Татьяна Б.Order No. ZK-2020/765 · 2 October 2020

ours

Жалоба простая: течёт. Отдельно спосибо мастеру — Дильмурат С, терпения ему хватило. Проверили при мне, показали, что всё держит!!

Repair: refrigerator

Куаныш Б.Order No. 2017-1993 · 27 June 2017

ours

Нужен был счёт и чек, у нас техника на балансе организации. Диагностика холодильника — с этого всё началось. Повод для визита: шумит. Поставили новую деталь: компрессор. Мастер посмотрел, сказал, что возьмёться, и взялся. С тех пор ни разу не подвёл.

Repair: refrigerator

Евгений М.Order No. TS-5582 · 15 February 2016

ours

Долго откладывал ремонт, потом всё-таки собрался. Привёз на диагностику: холодильник. С чем пришёл: намерзает лёд. Ни копейки сверху, как и обещали. Разобрали, посмотрели: уплотнитель. Приняли без очереди, оформили за пять минут. Хороший сервис, побольше бы таких. Крутит ровно, без рывков

Repair: refrigerator
See all reviews
Questions and answersQuestionsTECH SERVICE07

Questions about Hansa refrigerator repair in Almaty

Didn’t find the answer? Message us on WhatsApp.

Ask a question
Why isn't my Hansa fridge cooling even though the light inside is on and the compressor is running?

If the light is on but there's no cold, it's usually a refrigerant leak or a clogged capillary tube: the compressor hums, but the refrigerant isn't circulating. Less often, the cause is a faulty thermostat or sensor. An at-home diagnostic will give you a precise answer.

Why is my Hansa fridge humming louder than usual or making a gurgling sound?

The humming is usually due to compressor wear or loose motor mounts, while gurgling comes from refrigerant movement or a clog in the system. The type of sound depends on the model, so a technician determines the cause during inspection. At-home diagnostics are free.

Can a Hansa fridge be repaired at home in Almaty, or does it need to be taken to a service center?

Almost all Hansa fridge repairs are done at home: replacing the relay, thermostat, sensors, fan, fixing leaks, and recharging refrigerant. Taking the unit to a service center is rarely needed, for example with complex compressor repairs. A technician arrives within 60 minutes.

What can I check myself before the technician arrives if my Hansa fridge has stopped cooling?

Check that the door closes tightly, there's no ice on the seal, and the temperature control is in a working position. Make sure the plug is in the socket and the circuit breaker hasn't tripped. It's best not to disassemble the unit or touch the refrigerant lines yourself.

How can I tell if the compressor in my Hansa fridge has failed rather than a refrigerant leak?

With a refrigerant leak, the compressor usually runs nonstop but there's no cold, and the condenser stays only partially warm. If the compressor won't start, hums, or trips the breaker, the problem is most likely in it. An accurate conclusion comes from pressure measurement and checking the windings.

Are old Hansa fridge models repaired in Almaty?

Yes, technicians work on old Hansa models, including discontinued ones. Parts are selected by model, and if original parts aren't available, compatible equivalents are used. Diagnostics are free, and a technician will arrive within 60 minutes in the city.

Repair guideArticleTECH SERVICE08

Hansa refrigerator repair in Almaty with a technician visit

Ruslan Ts., washing machine and refrigerator repair technician

Author: Ruslan Ts.,Washing machine and refrigerator repair technician

Published
Updated

Tech Service repairs Hansa refrigerators in Almaty with its own technicians who have 4 to 20 years of experience. A technician arrives at your home within 60 minutes anywhere in the city, diagnostics are free, and there is a 1-year warranty on labor and parts. The technician quotes the price after diagnostics, and you can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies.

What breaks in Hansa refrigerators and how it shows

Like any brand, Hansa has its own set of typical symptoms. From them, the technician already knows where to look for the cause when they arrive.

Hansa refrigerator doesn't cool but the light is on

  • Power is fine: if the light inside comes on, the unit is getting voltage, so the cause is inside the cooling circuit or in the motor start assembly.
  • Motor hums but no cold: a steady hum without cooling almost always points to a refrigerant leak or a clogged capillary tube.
  • Silence with clicks: the motor doesn't start and the start-protection relay opens the winding — a sign of wear on the part or the assembly itself.
  • The motor compresses the refrigerant and pushes it through the circuit; if the seal fails, pressure drops and the evaporator stops cooling the compartments.
  • Freezer works, fridge doesn't: often the capillary tube is clogged or the fan that blows cold air upward is faulty.

Clicks, won't start, won't stop

  • Clicks without starting: the start-protection relay opens the circuit because the motor won't turn — worn contacts or a seized assembly.
  • Runs non-stop: a continuous cycle points to the thermostat, temperature sensor, or a leak that prevents the unit from reaching the set mode.
  • The thermostat controls motor on/off: if it fails, the motor either stays silent or runs without pauses.
  • Temperature sensors give false readings: the electronics get wrong data and don't send the command to stop the motor.
  • Don't keep the unit plugged in hoping it will 'start': the motor winding heats up for nothing, and the assembly can fail completely.

Ice builds up, noise and leaks

Ice on the back wall of the fridge compartment, humming, and water under the drawers are three different signals of a problem. Frost buildup points to a defrost system failure or a loose door seal, noise comes from the fan or motor, and a leak is linked to a clogged drain hole. In No Frost models, the defrost heater and fan remove moisture: if the heater burns out, the evaporator gets covered in ice and cold stops reaching the compartments. A thin layer of frost on the back wall of a drip model between defrost cycles is normal, but thick ice and puddles under the bottom drawers already indicate a breakdown. If you notice such symptoms, it's best to leave Hansa refrigerator repair in Almaty to a technician who comes to your home. Listen to the hum: a steady rising sound often comes from the motor, while an intermittent one comes from the fan.

Error codes and electronics of Hansa refrigerators

Models with a display show a self-diagnostic code, and from it you can see in advance which assembly to check. Mechanical versions have no codes — the symptom is read from how the unit behaves.

What the codes on the display mean

Display readingWhich assembly it points toWhat we check first
Compartment temperature deviationtemperature sensorsensor readings vs. actual temperature
Defrost deviationdefrost heater, timerdefrost circuit and ice on the evaporator
Board communication deviationcontrol moduleboard contacts and harnesses
Start deviationstart-protection relaycompressor start and windings

How Hansa electronics differ from mechanical controls

  • Thermostat: in mechanical models, the mode is maintained by a mechanical thermostat that opens the circuit based on evaporator temperature.
  • Control module: in electronic versions, the mode is controlled by a board that reads temperature sensors in the compartments.
  • Temperature sensors: electronics receive data from multiple points, so they maintain the mode more accurately, but there are also more failure points.
  • Diagnostics: on mechanical models, a technician often gets by with replacing the thermostat or relay, while on electronics they first rule out the sensor and wiring.
  • Check order: you can't replace a component on the board without reason — first, the sensor readings are compared with the actual cold.
  • Symptom "not cooling": with the same complaint on mechanical and electronic models, it leads to different components, and confusing them is costly.

When the error code isn't the main thing

We sometimes see the display silent while the cold is already gone: then we focus on compressor behavior and compartment temperature, not the code. The Hansa self-diagnosis system doesn't catch everything — a sensor can drift gradually without a sharp response, and the board continues to consider the mode normal. If the code doesn't return after defrosting and restarting, it doesn't mean there's no fault: the board may have reset the warning, but the cause remains. At Tech Service, we first take the actual temperature in both compartments and listen to the compressor startup, and only then compare it with what the display shows. This order cuts off false conclusions based on the code alone and saves you from replacing working components.

How a technician finds the cause during at-home diagnostics

We start Hansa refrigerator repair in Almaty with at-home diagnostics — a sequence of checks from simple to complex. Its job is not to guess the fault but to rule out versions until one cause remains.

Compressor or refrigerant leak

The compressor and a leak produce a similar "not cooling" symptom, but they differ in sound and in how the circuit behaves: a working unit hums and gets warm, while with a refrigerant loss it either stays silent or runs without cooling. The technician listens to startup, measures power consumption, and checks pressure in the refrigerant circuit — these three points show whether the motor is pumping or just running empty. Refrigerant escapes through joints, valves, or the capillary tube, and the location is found by oil traces and pressure testing. A silent unit is checked separately: seizure, an open winding, and a faulty start relay all produce the same silence but are fixed differently. A leak isn't solved by just recharging: first, the point of refrigerant loss in the circuit is found, otherwise the refrigerant will escape again through the same joint.

Thermostat, sensor, or board

We check the control chain in order: thermostat or sensor, then wiring, and only then the board, because a sensor is simpler and cheaper to replace than a module. First, we compare temperature sensor readings with the actual cold in the compartments: a difference of a few degrees already indicates a component failure. Next, we test the wiring from the sensor to the control module — an oxidized contact mimics an electronics fault and confuses during the first inspection. We look at the module itself last: traces, relays, signs of overheating on the board. With a mechanical thermostat, the logic is simpler — we check whether it opens the circuit when the required cold is reached. If the compartment holds temperature with a large spread but the motor is working, the cause is more often in the sensor, not the unit itself.

What's included in free diagnostics

  • Power and electrics: we check the outlet, wiring, and circuit breaker to rule out an external cause.
  • Compressor startup: we listen and measure how the unit starts and maintains the mode.
  • Circuit and refrigerant: we check for leaks and whether the capillary tube is clogged.
  • Controls: we compare the thermostat, sensors, and board with the actual temperature.
  • Outcome: we name the cause and the scope of work before starting.

Hansa refrigerator repair procedure at home

Hansa refrigerator repair in Almaty is most often done at home: most jobs don't require taking the appliance to a service center, and the technician comes to you.

What the technician does step by step

  • Request and visit: a technician reaches you within 60 minutes anywhere in the city.
  • Diagnostics: we check the components free of charge and find the cause instead of replacing parts at random.
  • Approval: we explain which component needs replacing and why, and give you the price before any work starts.
  • Repair: we install a new part or fix the cause on site, or at the service center if bench testing is needed.
  • Check: we make sure the appliance reaches its mode and holds it after reassembly.
  • Warranty: 1-year warranty on labor and parts.

Most common repairs

RepairWhen it's neededWhat we check afterward
Compressor replacementthe unit won't start or hold its modestart-up and temperature pull-down
Refrigerant rechargea leak in the circuit is confirmedseal tightness and cooling
Thermostat replacementthe mode won't switchshut-off by temperature
Relay replacementclicking without startingstable start-up
Module replacementthe board doesn't control the componentssensor and defrost operation
Clog removalthe circuit won't pass refrigerantflow and cooling

What to do if it stops cooling again after repair

If the cold doesn't come back, we return under warranty and check the work again, because the 1-year warranty covers both labor and parts. In our experience, a repeat visit is more often caused not by the component itself but by a cause that wasn't fixed the first time: a micro-leak of refrigerant in the foamed part of the circuit, a clogged capillary tube, or disturbed module settings. The technician goes through the circuit again, checks pressure and compressor start-up, and compares sensor readings with the reference values. Don't take the unit apart before the technician arrives: you can void the warranty and make it harder to find the cause. Keep access to the rear grille and don't defrost the appliance for more than a day — this helps recreate the conditions under which the defect appeared.

Hansa model specifics and what to do before the technician arrives

Different Hansa families fail in their own way, and before the technician arrives there are a few safe steps that help avoid making the breakdown worse and speed up the repair.

Old and new models, No Frost and drip systems

Older Hansa models more often wear out the thermostat, start relay, and door seal, while newer No Frost models tend to have issues with the fan, defrost heater, and defrost timer, so the checks focus on different components. In drip refrigerators, moisture runs down the back wall into the drain hole, and if it's clogged you get puddles under the drawers — that's not a compressor failure but a blocked drain. In No Frost units, ice builds up on the evaporator out of sight, and the first sign of a defrost failure is weak cooling while the motor is running. For discontinued models, one thing matters: the technician selects a component by its specifications, not just by the model name, so a repair is possible even without factory parts. Before calling, note the defrost type and series: that helps the technician bring the right parts straight away.

What you can check yourself before the technician arrives

  • Power: check that the outlet works and the breaker in the panel hasn't tripped.
  • Thermostat: make sure the setting isn't turned down to minimum.
  • Door: check that the seal fits tightly and dishes aren't in the way.
  • Defrost: if there's ice, defrost the compartment and switch it back on, then check the cooling.
  • What not to do: don't take components apart or touch the refrigerant circuit yourself.
  • Result of the check: if the cold doesn't return within a few hours, that's a sign of a breakdown, not just a setting.

What not to do when something breaks

Don't try to mess with the circuit, remove the control module, or leave a clicking refrigerator plugged in for a long time: this makes repairs harder and can finish off the compressor. Attempts to adjust the relay or manually bridge the contacts often lead to a short circuit and a fried board. The electrical part — the outlet, wiring, breaker — should be checked by a technician, because some faults are related to the power supply, not the appliance itself. If the refrigerator smells like burning or gives you a shock, it's best to unplug it and not turn it on until the technician arrives. A refrigerator with signs of a refrigerant leak should also be left alone: recharging and soldering the circuit require tools and refrigerant, not a screwdriver in the kitchen. In our practice, such cases are rare, but they are exactly the ones that require immediate disconnection from the power grid.

Calling a technician, warranty, and terms of service

Once the cause of the breakdown is found, you need to understand the terms of repair and the result afterward: who will come, how long to wait, and how the warranty and payment work.

How to call a technician and how long to wait

You can call a technician to your home, and we arrive within 60 minutes anywhere in the city. Our own specialist does the work, not a middleman. You can request service by phone: just tell us the model of your Hansa refrigerator and describe the symptoms — not cooling, clicking, or leaking. The specialist arrives with their own tools and inspects the appliance on the spot, so you don't need a separate trip to the service center and back. Within the city, arrival takes up to an hour, and we agree on the exact visit time when confirming the request. The same person who will handle the job from start to finish comes to your home — they will also call before heading out to clarify details. The sooner you request service, the faster the specialist can look at the refrigerator before the breakdown affects other components.

Warranty and payment

We provide a 1-year warranty on labor and parts and you can pay via Kaspi QR, Kaspi Red (instalments), bank card, cash, or bank transfer for companies. We quote the price after free diagnostics. First, we find the cause, explain which component failed and what repair options are possible, and only then give you the price — no surprises at the end. You can pay in cash, by card, or by bank transfer, whichever is convenient. The warranty covers both the installed part and the work itself, so if the same component fails again, we fix it at no charge. Protection for parts is just as important as for labor: if a new component fails, it's resolved under warranty, not at your expense. That's why the 1-year term applies to both the part and the work performed — the owner doesn't have to deal with the consequences alone.

Why a direct contractor, not a middleman

  • Our own specialist: the person who comes to you is from our service center, not a dispatcher who forwards the request to a third party.
  • Experience from 4 to 20 years: our technicians work with Hansa refrigerators of varying complexity and know the brand's typical components.
  • One responsible person: the same person does the diagnostics and the repair, so the one who did the work is responsible for the result.
  • Transparent terms: 1-year warranty on labor and parts, payment by any method, price after free diagnostics.
  • No middleman markup: you pay for the technician's work, not for a dispatcher forwarding your request.

When a Hansa refrigerator repair pays off

Hansa refrigerators fail in a few typical ways, and each one needs its own check. Here are short takeaways to help you make the right call when something breaks.

  • A symptom is not a diagnosis: "not cooling" sounds the same whether it's a leak, the compressor, or the thermostat, so the components need to be tested.
  • The display code points the way: it indicates a component, but the decision is made based on actual temperature and compressor behavior.
  • Diagnosis matters more than replacement: without finding the cause, a new part won't solve the problem for long.
  • The model matters: older models, No Frost, and electronics fail in different ways.
  • Before the technician arrives: check the power and the door, but don't touch the circuit or the board.

90brands

Besides Hansa, we repair other refrigerator brands in Almaty

We work with every brand sold in Kazakhstan — from Samsung, LG and Atlant to Biryusa, Indesit, Stinol and rare imported makes. Can’t find yours in the list? Call anyway — a technician will come and take a look.

We also repairWe also repairTECH SERVICE09

Besides Hansa refrigerator repair, we fix other equipment in Almaty

Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.

BlogBlogTECH SERVICE10

Worth reading before Hansa refrigerator repair in Almaty

Leave a review

Choose a platform — the TECH SERVICE page will open.

2ГИС2GISGoogle MapsЯYandex Maps
Send a review with photos on WhatsApp