experience9 yearsRuslan Ts.
Washing machine and refrigerator repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 746 00 26Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Free diagnostics.
Our own technicians4 to 20 years of experience




Repair prices
Below are typical symptoms and likely causes. The technician will pinpoint the exact fault after diagnostics.
Refrigerant leak, compressor failure
from10 500 ₸
Faulty defrost sensor or heater
from6 000 ₸
Clogged drain, worn door seal
from5 000 ₸
Compressor wear, installation errors
from24 500 ₸
Code points to a sensor or motor
from6 000 ₸
Clogged capillary tube, faulty thermostat
from9 500 ₸
Clog, leak, faulty fan
from10 500 ₸
Thermostat or temperature sensor failure
from9 500 ₸
The table shows Nord refrigerator repair prices: a starting labor price without parts and the time it takes; the technician confirms the final total before any work begins.
1 visittime
from 9 500 ₸cost

BeforeAfter5 steps

Five steps from request to confirming the technician's visit time.
Describe the symptom and your Nord refrigerator model so the technician brings the right tools.
A technician arrives within 60 minutes anywhere in the city. The technician comes with diagnostic equipment.
The technician checks the components on site and records the found fault in the request.
You approve the scope of work and the price, then the technician starts the repair.
Confirm the model, symptom, and access to the appliance with the technician so they arrive prepared.
The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsField refrigerator repair technician
experience12 yearsGeneral household appliance repair technician
experience8 yearsExpert washing machine repair technician
We reply during working hours
Leave a request — a technician will arrive within 60 minutes anywhere in the city. Specify a convenient visit time and we will confirm the request. 1-year warranty on labor and parts.

Warranty question? Call us
+7 (778) 746 00 267 898 reviews of repairs at TECH SERVICE in total
Асель Ж.Order No. 2026-4630 · 5 February 2026
oursДолго искал, кому это отдать, и вот нашёл. Повод для визита: намерзает лёд. Никита М объяснил причину так, что понял даже я. Сказали 32 500, я согласился без торга. Диагностику сделали бесплатно, хотя я был готов платить. В списке работ — уплотнитель. Рекомендую. Проверили при мне, показали, что всё держит
Мадина Т.Order No. TS-7219 · 28 November 2024
oursХотел сначала вызвать мастера на дом, потом передумал. Нужен был ремонт холодильника — обратился сюда. С чем пришёл: шумит. Сказали 27 000, а потом ещё и скидку сделали. Приехал вечером, мастер ещё был на месте. Заодно поменяли: термостат. В помещении тесновато, но это мелочи. Внешне как новый, если не считать мелкой царапины!!
Индира П.Order No. ZK-1617 · 20 September 2024
oursХотел сначала вызвать мастера на дом, потом передумал. Техсервис на Абая, если не ошибаюсь, — вот туда и поехал. Проверили на всех режимах, всё чётко!!
Лилия В.Order No. TS-4770 · 30 May 2024
oursРаботаю допоздна, поэтому нужен был сервис с нормальным графиком. Основная жалоба — намерзает лёд. Проверили при мне, показали, что всё держит.
Аружан К.Order No. ZK-2416 · 24 February 2023
oursДо этого обращался в другой сервис, там только развели руками. Проблема — не морозит. Проверили при мне, показали, что всё держит.
Данияр С.Order No. TS-2205-673 · 5 April 2022
oursДруг посоветовал, у него похожая история была. С чем пришёл: не морозит. Проверили при мне, показали, что всё держит.
Алексей Г.Order No. TS-4782 · 30 August 2021
oursБыло подозрение, что дело в плате, хотелось услышать второе мнение. Приехал из командировки, а дома — шумит. В списке работ — уплотнитель. Проверил дома — всё на месте, ничего не забыли
Татьяна Б.Order No. ZK-2020/765 · 2 October 2020
oursЖалоба простая: течёт. Отдельно спосибо мастеру — Дильмурат С, терпения ему хватило. Проверили при мне, показали, что всё держит!!
Станислав К.Order No. TS-3337 · 28 February 2017
oursПовод для визита: шумит. Дильмурат С всё объяснил и не пытался впарить лишнее. Уже полгода — ни одного сбоя.
Евгений М.Order No. TS-5582 · 15 February 2016
oursДолго откладывал ремонт, потом всё-таки собрался. Привёз на диагностику: холодильник. С чем пришёл: намерзает лёд. Ни копейки сверху, как и обещали. Разобрали, посмотрели: уплотнитель. Приняли без очереди, оформили за пять минут. Хороший сервис, побольше бы таких. Крутит ровно, без рывков
Didn’t find the answer? Message us on WhatsApp.
Ask a questionMost often it's the start relay: it clicks as it tries to start the motor, but the motor doesn't kick in. Less often the compressor itself is seized. It depends on the model, and a technician will give you a precise answer after free diagnostics.
With a leak, the motor runs nonstop but there's no cooling, and the condenser at the back only heats up partially. If the compressor has failed, you'll hear clicking and it won't start. A technician determines the exact cause on site.
This usually points to a refrigerant leak, a clogged capillary tube, or a faulty defrost sensor. It depends on the model and defrost type, so a technician will pinpoint the cause during free diagnostics.
Yes, compressor replacement in Nord refrigerators is possible, and the technician does the work at your home. Time depends on the model and access difficulty; the technician will give you an exact timeframe after free diagnostics.
No, loud humming after defrosting isn't normal. The cause may be improper installation, compressor mounts, or the fan, depending on the model. It's worth calling a technician for diagnostics.
It depends on the age, model, and nature of the fault: fixing a specific component is usually cheaper than buying a new appliance. After free diagnostics, the technician will quote the repair cost so you can compare.
Tech Service repairs Nord refrigerators in Almaty directly, without middlemen: our technician comes to your home within 60 minutes anywhere in the city or takes the appliance to the service center. Diagnostics are free, 1-year warranty on labor and parts, and the technician quotes the price after diagnostics. Technicians have 4 to 20 years of experience.
Nord refrigerators don't break all at once—specific components fail. Let's break down which symptoms point to which parts so you understand what you're dealing with.
If the light inside is on but there's no cold, power is reaching the unit, and the cause is almost always in the cooling circuit or the component that starts the compressor. The motor may hum but not build pressure, or it may not start at all due to the start relay. A refrigerant leak causes loss of cooling while the unit formally runs: the condenser on the back wall stays warm only at the inlet, and the evaporator gets uneven frost. The start relay is checked for contact and resistance—a burnt terminal block or cracked housing explains clicking without starting. The control module should be checked last: it rarely fails on its own, more often after a voltage spike. Starting with the compressor is pointless until you rule out refrigerant leak and start relay—they cause this symptom most often. If DIY diagnostics don't help, a technician repairs Nord refrigerators in Almaty after a free on-site check.
In two-compartment Nord models, the freezer and fridge compartments share one compressor, so when the freezer fails while the fridge still works, the search narrows to the circuit and cold distribution. Drip defrost in the fridge compartment explains frost on the back wall: moisture runs down the groove, and if the drain is clogged, it goes inside or under the unit. In No Frost models, defrost failure adds to the cold symptoms, and then the problem looks like a compressor failure, though it's actually the heater or sensor. Over years of working with this brand, our technicians have learned to first rule out cheap causes—relay, sensors, drain—and only then touch the circuit. In the No Frost system, the heater melts frost on the evaporator, and its failure gives the same picture as a refrigerant leak.
The Nord refrigerator display shows not text but a combination of symbols tied to a specific component. Let's break down how to read such a combination, what to do before the technician arrives, and when an electronics failure leads to module repair.
The combination on the Nord display is the fault address, not a verdict on the component: it points to the circuit (sensor, defrost, fan, module communication) that the technician checks first. The electronic control module manages modes and the defrost cycle in No Frost by polling the evaporator temperature sensor, defrost sensor, and fan; when any circuit goes out of range, the board logs a fault and enters protection mode. The same symbol on different series can mean different things, so the decoding is checked against the specific model, not just a table. If an error code appears on the display, Nord refrigerator repair in Almaty starts with checking the circuit indicated by the code. Some signals appear only under certain conditions—for example, forced defrost or a long cycle—and then the display shows a flashing code rather than a steady one. Don't reset the signal by power-cycling before the technician arrives—the stored code helps locate the fault faster.
The Nord control module is repairable: we either restore the board or replace it, and this is almost always cheaper and faster than replacing the entire refrigerator. The board fails for a specific reason — a blown defrost triac, a broken trace, a dried-out capacitor in the power circuit — and the Tech Service technician first finds that reason, then decides whether to solder or install a new module. In our practice, board restoration covers most electronics calls: replacement is needed when a section under several circuits has burned out or the traces are so damaged that solder won't hold. The decision depends not on the age of the appliance but on the condition of the compressor and circuit — if they are fine, electronics are no reason to part with the refrigerator.
After a power surge, the control module and starting electrics are the first to suffer, while the compressor usually remains intact. The impulse breaks through the varistor and triacs on the board, burns the winding of the start relay, or jams the protection relay — and the appliance goes silent without clicks or clicks and won't start. A faulty start relay is exactly what causes clicking and failure to start the compressor, so the technician checks it together with the board, not separately. A separate trap is a voltage stabilizer or surge protector plugged in after the appliance: they mask the damage and prevent assessing the board's condition during the first inspection. Do not turn the refrigerator on again 'on the off chance' — with a damaged module, repeated power supply can finish off a unit that was still repairable.
Three components produce similar symptoms: the refrigerator doesn't cool or won't start. They are repaired differently, and the difference determines what the technician checks.
With a refrigerant leak, the compressor runs but there is no cooling; with a compressor failure, it won't start but hums and shuts off on protection. The compressor of a Nord refrigerator compresses the refrigerant and drives it through the circulation circuit — through the condenser on the rear grille, the capillary tube, and the evaporator in the compartments. If the seal is broken, pressure drops and the refrigerant doesn't reach the evaporator in the required volume: the motor hums continuously, and the temperature in both compartments rises. When the motor is worn, the picture is different — it doesn't build the required pressure or trips the protection on start. A leak is not fixed by simply recharging: first the leak point is found and sealed, most often at a solder joint or in the foamed part of the circuit, otherwise the refrigerant will escape again in a few weeks.
We replace the compressor in a Nord refrigerator with a warranty on the part and labor, and after replacement we refill the circuit with refrigerant and check cooling in both compartments. Before replacement, the technician makes sure the motor is truly worn out beyond repair: he tests the windings, measures the starting current, and compares the readings with the model's specifications. The new compressor is selected for the specific Nord model based on cooling capacity and refrigerant type, not "by size" — a mismatch in these parameters shortens the unit's lifespan. After installation, the circuit is evacuated, charged with refrigerant by weight, and then the appliance runs under observation: the technician records the temperature in the refrigerator and freezer compartments. The 1-year warranty covers both the part and the labor. Compressor replacement is justified when the motor has burned out or reached the end of its life; if the motor is working and there's a leak, it's enough to find the damage and restore the circuit's tightness.
| Component | How it manifests | What we check | What we do |
|---|---|---|---|
| Start relay | Clicking, compressor won't start | Relay contacts, motor windings | Replace the relay |
| Compressor | Hums and shuts off on overload | Windings, starting current | Replace the compressor |
| Refrigerant leak | No cooling, motor runs | Circuit, solder joints | Find the leak, recharge |
| Thermostat | Doesn't turn off, ice buildup | Sensor response | Replace the thermostat |
We'll show you the path from request to post-service inspection and what's included in free diagnostics, so the owner knows what to expect at each step.
We do most work at your home, and we take the appliance to the service center when a compressor replacement or complex circuit work is needed. On-site, we replace relays, thermostats, sensors, fix wiring breaks, and restore electronics — our tools and stock of common parts are enough for that. Compressor replacement and circuit soldering require stationary conditions: there it's easier to evacuate the system and charge it with refrigerant without risk to the apartment. The specialist chooses the format based on diagnostic results, not the owner in advance — so the refrigerator doesn't get transported unnecessarily. In our practice, half of the requests the client planned to "take out" are resolved on-site in one visit. A city visit takes up to 60 minutes, and diagnostics are free — so the decision on format is made right in the kitchen, after inspection.
You don't need a full defrost before the technician arrives, and it often gets in the way: frost and how the components behave make it easier to find the cause. A layer of frost on the evaporator shows how cold is distributed and where the circuit is working unevenly, and the pattern of ice hints at whether refrigerant is leaking. The thermostat turns off the compressor when the set temperature is reached—if you defrost the compartments, that cycle is disrupted, and you can't see how the unit behaves in real operation. Just clear access to the back wall and don't unplug the fridge in advance—that way the symptom is visible live. It's best to move food from the top shelves so it doesn't block the evaporator. And if the appliance hasn't been cooling for a day and the compartments are empty, there's nothing to defrost—we go straight to measuring pressure in the circuit.
Let's clarify who exactly will come on your request, what direct work with the contractor gives you, and how the warranty on Nord refrigerator service is structured—no middlemen, no passing the buck.
Our technician with 4 to 20 years of experience comes to you, not an aggregator's employee: Tech Service is the direct contractor, and we stand behind the work ourselves. The same service that takes your request is the one whose technician later stands at your Nord refrigerator—there's no dispatcher between you passing the order to a third party. That experience means they've already worked on top- and bottom-freezer platforms, single- and dual-compressor setups, and electronic and mechanical thermostats. On site, they run the diagnostics themselves and identify the fault themselves, rather than coordinating it with someone over the phone. Direct contractor means the same organization that sent the technician is responsible for the result, and the warranty isn't shifted to a third party.
We provide a 1-year warranty on labor and parts, including compressor replacement—it covers the entire scope of work, not just the part. If after replacing the start relay or compressor the refrigerator stops cooling again, the same technician who installed the component will handle it, not the parts supplier or a third party. The year covers both the part itself and the quality of its installation: brazing the circuit, vacuuming, refrigerant charging, and thermostat adjustment. In my view, this is the main difference between direct work and an intermediary scheme, where the warranty on the component and the warranty on the installation are given by different parties. A warranty on a part without a warranty on the labor is useless: if the component fails due to installation, the one who installed it should be responsible.
The technician arrives within 60 minutes anywhere in the city, and you can pay via Kaspi QR, Kaspi Red, card, cash or bank transfer. Diagnostics are free: the specialist comes, finds the cause, and only then tells you which component needs to be replaced and how. We accept cash, transfers, and bank cards—you choose the method yourself, and you won't have to change it during the work. The technician quotes the price after free diagnostics, so the final amount is known before work begins. From our practice: Nord owners often put off calling because they worry the price will be named only after the appliance is taken apart—with this workflow that risk is removed, you agree on the figure in advance and can decline if it doesn't suit you.
Here are the key takeaways on diagnosing and repairing Nord refrigerators — a quick guide to help you tell a simple glitch from a serious breakdown and prepare for a conversation with a technician.
90brands
We work with every brand sold in Kazakhstan — from Samsung, LG and Atlant to Biryusa, Indesit, Stinol and rare imported makes. Can’t find yours in the list? Call anyway — a technician will come and take a look.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your refrigerator stops working, first check the outlet, the power cord, and the thermostat setting, and after defrosting let it stand for a while.
4 February 2026 · 12 minutes read
If your refrigerator isn't cooling but the light is on, the cause is usually one of the components in the cooling circuit: the compressor, thermostat…
10 December 2025 · 13 minutes read
If your dishwasher won't drain, the most common culprits are a clogged filter or drain hose; less often, it's the pump, impeller…
24 March 2026 · 12 minutes read
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
If your microwave isn't heating but the light and turntable still work, the problem is usually one of the high-voltage components — the magnetron, diode…
15 February 2026 · 12 minutes read












