experience9 yearsRuslan Ts.
Washing machine and refrigerator repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 746 00 26Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Diagnostics are free.
Our own technicians4 to 20 years of experience




Repair prices
Below are frequent symptoms of refrigerator breakdowns. The technician will pinpoint the exact cause during free diagnostics.
refrigerant leak, compressor failure
from10 500 ₸
no power, faulty thermostat
from9 500 ₸
clogged drain, damaged door seal
from5 000 ₸
compressor wear, loose mounts
from24 500 ₸
defrost sensor failure, door left open
from6 000 ₸
temperature sensor or control board failure
from6 000 ₸
clogged capillary tube, faulty damper
from10 500 ₸
defrost failure, faulty timer
from6 000 ₸
The table shows Stinol refrigerator repair costs: the labor price "from" (parts not included) and the turnaround time; the technician confirms the final amount before starting the repair.
1 visittime
from 6 500 ₸cost

BeforeAfter5 steps

Five steps from request to checking the refrigerator's operation.
You describe the symptom (not cooling, leaking, noisy) and the refrigerator model — the technician brings the right tools.
The technician identifies the cause of the problem and names the failed component.
You approve the scope of work and the price, and the technician starts the repair.
The technician replaces faulty parts and adjusts the refrigerator's operation.
The technician demonstrates the refrigerator working after repair and hands over the documents.
The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsField refrigerator repair technician
experience12 yearsGeneral household appliance repair technician
experience8 yearsExpert washing machine repair technician
We reply during working hours
Describe the problem and a convenient time — the technician will arrive with tools and parts. On-site diagnostics will reveal the cause, and the timeline and price are agreed before repair.

Warranty question? Call us
+7 (778) 746 00 267 898 reviews of repairs at TECH SERVICE in total
Асель Ж.Order No. 2026-4630 · 5 February 2026
oursДолго искал, кому это отдать, и вот нашёл. Повод для визита: намерзает лёд. Никита М объяснил причину так, что понял даже я. Сказали 32 500, я согласился без торга. Диагностику сделали бесплатно, хотя я был готов платить. В списке работ — уплотнитель. Рекомендую. Проверили при мне, показали, что всё держит
Алексей Г.Order No. TS-2501-114 · 4 August 2025
oursРаботаю допоздна, поэтому нужен был сервис с нормальным графиком. По деньгам вышло адекватно, в другом месте просили больше. Уже полгода — ни одного сбоя)
Ерасыл Б.Order No. 954197 · 13 August 2021
oursТехника на гарантии уже не была, так что выбор был свободный. Честно говоря, доверяю больше тем, кто говорит по делу. Симптом был очевидный: течёт. Из деталей — термостат. Вышло 20 000 тенге, дешевле, чем я рассчитывал. Ответили быстро, не пришлось ждать на линии. Техсервис на Абая, если не ошибаюсь, — вот туда и поехал. Уже полгода — ни одного сбоя.
Азамат Е.Order No. 20528 · 1 May 2021
oursДруг посоветовал, у него похожая история была. Первое, что заметил: течёт. Починили и дали гарантию на месяц.
Сергей Р.Order No. 598321 · 25 April 2020
oursВыбирал по отзывам в 2ГИС, времени на эксперименты не было. До последнего откладывал, но пришлось признать: шумит. Могли бы взять больше, но взяли по-божески. Заявку приняли по телефону, перезвонили через десять минут. Деталь на замену — уплотнитель. Пять звёзд, не задумываясь. Ребёнок уже проверил на прочность, держится.
Светлана Д.Order No. ZK-2019/136 · 30 May 2019
oursБыло подозрение, что дело в плате, хотелось услышать второе мнение. Честно, уже готовился покупать новое, но обошлось. Проблема — шумит. Проверил дома — всё на месте, ничего не забыли.
Аяна Е.Order No. 25364 · 9 December 2017
oursОтдал мастеру: холодильник. Жалоба простая: шумит. Никита М объяснил причину так, что понял даже я. Смета совпала с итогом, что редкость. Поставили новую деталь: термостат. Мастер сразу сказал, что к чему, без размытых формулировок. Нагрев в норме, посторонних звуков нет.
Станислав К.Order No. TS-3337 · 28 February 2017
oursПовод для визита: шумит. Дильмурат С всё объяснил и не пытался впарить лишнее. Уже полгода — ни одного сбоя.
Акбота Т.Order No. ZK-2520 · 13 April 2016
oursПроблема — шумит. Никита М подсказал, как продлить жизнь технике. Починили и дали гарантию на месяц.
Сергей Р.Order No. ZK-8150 · 20 March 2016
oursХотел сначала вызвать мастера на дом, потом передумал. Нужен был ремонт холодильника — обратился сюда. Основная жалоба — шумит. Всё оформили по договору, с печатью. Заодно поменяли: термостат. Вышло 34 500 тенге, дешевле, чем я рассчитывал. Однозначно да. Проверил дома — всё на месте, ничего не забыли.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionMost often the bulb itself has burned out or the contact in the socket has oxidized. Less commonly, the cause is in the wiring or control module — the technician will check this during free diagnostics.
Unplug it, remove the food, and leave the doors open until it fully thaws. Don't chip ice with a knife or use a hairdryer — you'll damage the evaporator; parts vary by model.
They often quote an inflated price over the phone, then demand more on site, or scare you with a compressor replacement without checking. At Tech Service, the technician gives you the price after free diagnostics, and the warranty is one year.
On models with a drip system, a thin layer of frost during operation is normal, but a thick buildup and ice on food indicate a defrost or thermostat failure. The technician will check the sensors and defrost timer at your home.
Yes, repairing the control board is possible. The technician will check the electronics and replace faulty components if needed; the warranty on labor is one year.
Yes, we repair old Stinol models too. Our technicians have four to twenty years of experience and are familiar with the design of Soviet refrigerators.
Tech Service repairs Stinol refrigerators in Almaty at your home and at our service center. A technician arrives within 60 minutes anywhere in the city, diagnostics are free, and there's a 1-year warranty on labor and parts. We work with electronic and electromechanical controls, including older Stinol models. The technician gives you the price after diagnostics.
Stinol breakdowns tend to cluster around a few components. Based on the symptom, the technician narrows it down to the motor, thermostat, start relay, or refrigerant circuit, and then verifies the specific cause during diagnostics.
If the light is on but there's no cold, power is reaching the unit, so we look for the cause in the motor, thermostat, or a refrigerant leak. The thermostat controls when the motor turns on, so if it fails, the power unit simply doesn't get the start command and stays off. A refrigerant leak shows up differently: the appliance runs nonstop, the condenser on the back grille stays only partially warm, and the cooling circuit loses pressure. A faulty temperature sensor in the fridge compartment sends incorrect readings, causing the unit to shut off prematurely. Which compartment is warm can point to the culprit: one warm compartment while the other works often indicates a local issue with the circuit or sensor, not a complete failure of the power unit. If you need Stinol refrigerator repair in Almaty, the technician checks each of these possibilities with instruments.
A click on startup usually comes from the start-protection relay, which tries to start the motor and then shuts it off via protection. This part sits on the motor housing and trips when the starting current exceeds the norm or the winding doesn't respond. At Tech Service, the technician first removes it and checks the contacts and winding resistance one by one. If the unit hums and then dies after the click rather than staying silent, the issue is narrowed to the relay and motor windings, and there's no need to replace the power unit right away. Silence after the click more often indicates a seized motor or a broken winding. Our diagnostics are free, so we verify with instruments, not by ear. The technician first rules out a broken winding and a seized shaft, then checks the start circuit under load. This sequence prevents replacing a working relay and quickly leads to the real cause of the click.
On electronically controlled Stinol models, self-diagnostics show a fault code or flashing icon on the panel. Decoding it narrows the search to a specific component and saves time during disassembly.
A flashing indicator on a Stinol signals a component malfunction, and we decode it based on the model and the combination of icons on the panel. The control module polls the temperature sensors, detects deviations from the norm, and displays a single flash or a sequence of several on the front panel. Models with a display show an alphanumeric code, while simpler versions only have a flashing light. The same icon can mean different things on different Stinol series, so the technician matches the combination to the specific model rather than interpreting the flash from memory. Before calling, take a photo of the panel while it's flashing — decoding from a photo is more accurate than from a verbal description. Such a photo immediately rules out half the possibilities and speeds up finding the faulty component.
| Indicator or code | Likely component | What we check |
|---|---|---|
| Temperature indicator flashing | Temperature sensor | Sensor readings and circuit |
| Defrost fault code | Defrost timer | Evaporator defrost cycle |
| Compressor code | Compressor, relay | Start-up and motor windings |
| Whole panel flashing | Control module | Power supply and board |
Stinol electronics record the effect, not always the cause, so the code points you in a direction rather than giving a ready diagnosis. A temperature sensor error often comes from a corroded contact in the connector or a worn wire in the door hinge, while the sensor itself still works. A compressor code sometimes comes from the start relay, not the motor windings. The control module can show a false code when the mains voltage drops or after a power surge. That's why a technician tests the whole circuit—from the connector to the board—before replacing a part. Replacing a sensor without checking the wiring brings the error back, and the job has to be done again. Measuring resistance and testing contacts takes less time than a second visit and shows the condition of the circuit right away.
Old Stinols aren't fully repairable: the decision depends on which part has failed and whether a replacement is available. Here's what can be restored and when restoration won't pay off.
If the compressor has failed and the body and circuit are worn, restoration may not be practical, and the specialist will tell you so directly. The motor-compressor is the most expensive part of a refrigerator, and replacing it on an appliance with corrosion in the circuit and a dried-out seal rarely brings it back to working condition for long. Signs that restoration won't pay off: rust on the lower part of the body, traces of previous repairs to the circuit, swollen insulation in the chamber, several faults at once. In such a case, replacing the motor means checking for leaks and recharging, and the worn body will keep letting heat in. An honest approach to the job means not taking on a restoration that won't pay off for the owner, so serious wear is a reason not to spend money on restoration. If the appliance can't be brought back to life on site, the service option is considered a last resort. Refrigerator repair for Stinol in Almaty in such cases starts with free diagnostics so you know in advance whether restoration will pay off.
For common older Stinol models, parts are available, but for rare series availability is confirmed before the visit. The thermostat, start relay, and door seal for single-compressor and dual-compressor Stinol units are selected by model and chamber type, and for rare series compatibility is checked separately. We service both configurations — with one motor and with two — and for each it's clear in advance which part gets replaced. Part availability matters more than its price: if the needed element isn't available, there's no point in taking the refrigerator apart for nothing — an alternative is discussed right away. For common components, compatibility is usually known in advance, and for rare series it's confirmed before the visit so the appliance isn't dismantled for nothing. That's why before the visit our technician matches the appliance model with the required part and doesn't take the job blindly, so the equipment isn't taken apart without the right part.
Our Stinol repair follows step-by-step from request to result check. The specialist comes to your home, and the refrigerator only goes to the service center when the work can't be done on site.
We service Stinol refrigerators on site, and we only take the appliance to the service center if the work can't be done at your place. Citywide arrival is within 60 minutes, so most requests are handled right at the owner's home. On site we replace thermostats, sensors, start relays, control modules, and fix leaks in accessible parts of the circuit. The refrigerator goes to the service center for work that requires workshop conditions: circuit soldering, compressor replacement, and refrigerant charging. A Stinol refrigerator repair technician inspects the appliance and immediately says which option fits the specific case. Home service is more convenient for the owner but not always possible: some circuit work is done at the service center, and this is explained during diagnostics.
After replacing the component, the specialist starts the Stinol and checks that the chambers reach working cold and the compressor runs normally. They monitor temperature build-up via sensors, listen to how the motor starts and stops, and inspect the refrigerant circuit for leaks after soldering. On models with electromechanical control, they additionally check that the thermostat triggers at the on and off thresholds. Then the technician verifies that the cycle repeats without issues and the chambers hold cold. The post-service check is more important than the replacement itself: if the refrigerator doesn't get cold while the specialist is there, the cause isn't fixed, and the job isn't considered done. This stage prevents repeat calls — the component is replaced but cold didn't come, so the search needs to go further and deeper.
Warranty and payment procedure are what a refrigerator owner clarifies before calling a technician. Let's break down what exactly the warranty covers, what to do if the problem recurs, and what makes up the final amount.
We provide a 1-year warranty on labor and parts, including compressor replacement in Stinol refrigerators. Replacing the motor is the most expensive operation in the unit, and the one-year coverage applies to both the component and its installation. Our technicians have 4 to 20 years of experience, and over that time we've learned that coverage depends on the direct contractor. At Tech Service, the same service center that accepts your request sends a technician to your home. A warranty makes sense when the work is done by the direct contractor: the same organization is responsible for the result, not an intermediary who simply forwarded the request. So when choosing a service, ask who will actually come and who is responsible for the result.
If your Stinol doesn't cool again after repair, we return to the refrigerator under warranty and look for the cause anew rather than just repeating the previous replacement. A repeat failure often means the first visit fixed the symptom, not the cause: the compressor may have failed, but the real culprit is a refrigerant leak or a clogged capillary tube. That's why the technician checks the entire cooling circuit—from the motor to the evaporator—not just the replaced component. For repeat warranty calls, the same terms apply: one year on labor and parts. This full circuit check saves a second visit: the root cause is found instead of just patching the symptom. If cooling disappears after the visit, note how the unit behaves—partially cooling, clicking, or silent—these details speed up the repeat diagnosis.
The technician gives you the price after a free diagnostic, and you can pay for the work in any convenient way—via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies. We don't quote a sum before the inspection: it depends on the component and the scope of work. Replacing a thermostat and replacing a compressor are tasks of different scale, and guessing over the phone would be misleading. During the free diagnostic, the technician determines which component has failed and only then gives you the final amount. This approach eliminates surprises in the bill: you know upfront what you're paying for and can compare the scope of work with the quoted price. A city visit takes up to 60 minutes, and diagnostics are free. The final amount is given only after the inspection—so payment is tied to a specific operation, not a guess. You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies.
Taken together, the signs of failure, error codes, and the order of work add up to a clear action plan for Stinol owners, and this plan helps you get to the cause faster.
90brands
We work with every brand sold in Kazakhstan — from Samsung, LG and Atlant to Biryusa, Indesit, Stinol and rare imported makes. Can’t find yours in the list? Call anyway — a technician will come and take a look.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your refrigerator stops working, first check the outlet, the power cord, and the thermostat setting, and after defrosting let it stand for a while.
4 February 2026 · 12 minutes read
If your refrigerator isn't cooling but the light is on, the cause is usually one of the components in the cooling circuit: the compressor, thermostat…
10 December 2025 · 13 minutes read
If your dishwasher won't drain, the most common culprits are a clogged filter or drain hose; less often, it's the pump, impeller…
24 March 2026 · 12 minutes read
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
If your microwave isn't heating but the light and turntable still work, the problem is usually one of the high-voltage components — the magnetron, diode…
15 February 2026 · 12 minutes read












