Open until 19:00+7 (778) 046 88 53Call a technician
Tech Service technician next to a refrigeration unit

Refrigeration Unit Repair in Almaty

A technician arrives within 60 minutes anywhere in the city. Diagnostics are free.

  • 1-year warranty on labor and parts
  • 4 to 20 years of experience
  • You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies

Our own technicians4 to 20 years of experience

Ruslan Ts.Damir M.Dilmurat S.Dima

Repair prices

  • Diagnostics0 ₸
  • Drive belt replacementfrom4 000 ₸
  • Filter drier replacementfrom5 000 ₸
  • Temperature sensor replacementfrom6 000 ₸
  • Drain repair and cleaningfrom6 500 ₸
All prices
2ГИСЯours4,97 898 reviews
2GIS · Google · Yandex · order database
Common faultsCommon faultsTECH SERVICE02

Common refrigeration unit faults in Almaty

Below are typical symptoms and likely causes. The technician will pinpoint the exact cause during inspection. Cost and timeline are given after diagnostics.

PricesPricesTECH SERVICE03

How much refrigeration unit repair costs in Almaty

The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.

Drive belt replacementparts not included

1–2 hours

from4 000 ₸

Filter drier replacementparts not included

1–2 hours

from5 000 ₸

Temperature sensor replacementparts not included

1–2 hours

from6 000 ₸

Drain repair and cleaningexact price — after the free diagnostics

1–2 hours

from6 500 ₸

Refrigerant leak repairexact price — after the free diagnostics

1–3 hours

from7 500 ₸

Before and afterBefore and afterTECH SERVICE04

Before and after refrigeration unit repair in Almaty

Evaporator frosting

1–2 hourstime

from 6,500 ₸cost

Problem
The evaporator was covered with a thick layer of frost and ice, air barely passed through the fins, and the edges were dirty.
What we did
The technician turned off the unit, defrosted the evaporator, removed ice and dirt from the fins, washed the surfaces, and checked for free air passage.
Result
The evaporator is clean, the fins are dry and free of frost, the gaps between them are open, and airflow is restored.
I want the same
Refrigerator: evaporator icing — after repairBeforeAfter
01 / 03
All repairs
TECH SERVICE mobile technician with a tool case

How refrigeration unit repair works on site in Almaty

Five steps from request to checking the unit's operation.

  1. Requestsame day as request

    Describe the symptom by phone or messenger so the technician brings the right tools.

  2. Technician visitwithin 60 minutes

    The technician arrives anywhere in the city within an hour after the request is confirmed.

  3. Documenting diagnosticsafter inspection

    Ask for the found cause to be recorded in the request and clarify which components it affects.

  4. Post-repair checkafter repair

    Make sure the unit holds the set temperature during a test period of operation.

  5. Handoverafter repair

    The technician hands the unit back to the owner and explains further operating steps.

Leave a request
TechniciansTechniciansTECH SERVICE05

Our home appliance repair technicians in Almaty

The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

  • 8 technicians in Almaty
  • 8–12 years of experience in the department
  • Article author Ruslan Ts., 9 years of experience
Mobile technician fixing a washing machine at the customer's home
Field technician at a customer’s home

The department has 8 specializations — they are listed on the technicians' cards.

01 / 08
Ruslan Ts., washing machine and refrigerator repair technicianexperience9 years

Ruslan Ts.

Washing machine and refrigerator repair technician

Damir M., general household appliance repair technicianexperience12 years

Damir M.

General household appliance repair technician

Dilmurat S., field technician for washing machine and refrigerator repairexperience10 years

Dilmurat S.

Field technician for washing machine and refrigerator repair

Dima, expert washing machine repair technicianexperience8 years

Dima

Expert washing machine repair technician

Nikita M., field refrigerator repair technicianexperience8 years

Nikita M.

Field refrigerator repair technician

Oraz, senior washing machine repair technicianexperience8 years

Oraz

Senior washing machine repair technician

Radik T., dishwasher repair technicianexperience11 years

Radik T.

Dishwasher repair technician

Rustem T., washing machine repair technicianexperience9 years

Rustem T.

Washing machine repair technician

We reply during working hours

Book refrigeration unit repair in Almaty

Leave a request so a technician can inspect the unit on site. Diagnostics are free — afterwards you'll know the cause of the breakdown and the cost of work.

TECH SERVICE administrator replying to a customer's WhatsApp message

Warranty question? Call us

+7 (778) 046 88 53
Customer reviewsReviewsTECH SERVICE06

Reviews of refrigeration unit repair in Almaty

Вероника П.Order No. 912949 · 3 November 2025

ours

Обращался в сервис по совету знакомых. Долго откладывал ремант, потом всё-таки собрался. По срокам не подвели. Мастер посмотрел, назвал причину, всё разложил по полочкам. Цену сказали сразу, без «ну потом посмотрим». Оформили всё официально, с гарантией. Работали аккуратно, ничего не поцарапали. Не пришлось ничего доказывать и просить. Могу рекомендовать!!

Артём К.Order No. ZK-2025/726 · 16 April 2025

ours

Обращаюсь не первый раз, поэтому есть что сказать. Пробовал найти мастера в своём районе, но все были заняты. Дамир М перезвонил, когда всё было готово. По срокам не подвели. Работали аккуратно, ничего не поцарапали. Оформили всё официально, с гарантией. Приняли быстро, объяснили, что и как будет. Однозначно да

Гаухар Н.Order No. 2025-7256 · 17 January 2025

ours

Сервис нашёл случайно, но остался доволен. Работаю допоздна, поэтому нужен был сервис с нормальным графиком. С чистой совестью советую.

Александра Н.Order No. 388464 · 24 July 2024

ours

Позвонил, когда техника встала окончательно. Отдельно спасибо мастеру — Сергей Архипов, терпения ему хватило

Алишер У.Order No. TS-2208-957 · 8 June 2022

ours

Нашёл по отзывам, решил попробовать. Сервис нормальный, обращусь ещё. Не пришлось ничего доказывать и просить.

Алишер У.Order No. 132198 · 29 September 2021

ours

Позвонил утром, к обеду уже всё решили. Позвонил знакомому, он раньше работал в сервисе, посоветовал этих. По срокам не подвели. Запчасть нашли без проблем. Ставлю пятёрку.

Алмас Д.Order No. 39714 · 7 September 2021

ours

Нужен был ремонт, искал вариант поближе. Искал мастерскую поближе к дому, чтобы не мотаться с техникой через полгорода. Проверили при мне, показали, что всё держит.

Нурасыл М.Order No. 2021-8792 · 16 June 2021

ours

Нашёл по отзывам, решил попробовать. Пять звёзд, не задумываясь. Дали гарантию и рекомендации на будущее.

Наталья С.Order No. 796846 · 17 February 2018

ours

Искал сервис с гарантией, чтобы не переделывать. Сергей Москоленко не стал навязывать дорогую запчасть, поставил нормальную. Включил, проверил, работает.

Николай Ч.Order No. 599802 · 1 November 2016

ours

Нужен был ремонт, искал вариант поближе. Оформили всё официально, с гарантией. Сервис нормальный, обращусь ещё)

See all reviews
Questions and answersQuestionsTECH SERVICE07

Questions about refrigeration unit repair in Almaty

Didn’t find the answer? Message us on WhatsApp.

Ask a question
What should I do if the reefer is noisy or won't turn off?

This symptom usually points to issues with the fan, compressor mounts, or a sensor that's preventing the unit from shutting down. Before the technician arrives, check whether the condenser is clogged and if the unit is standing level.

How can I tell a refrigerant leak from compressor wear when cooling is lost?

With a leak, the compressor runs continuously but the temperature doesn't drop, and there may be oil traces on the pipes. Compressor wear is often accompanied by noise and vibration. Only diagnostics will pinpoint the exact cause.

Can a reefer container be repaired on-site without taking it to the shop?

Some reefer container work can be done on-site if there's access to the unit and no major disassembly is needed. The technician determines what can be fixed on location and what requires the shop after a free diagnostic.

Why is a refrigerant leak in a reefer dangerous if trips continue?

Without refrigerant, the unit can't maintain temperature, and the cargo may spoil while the compressor runs idle and wears out. If you suspect a leak, it's best to stop trips and call a technician.

Why does the reefer frost up and get icy even though the door is closed?

Ice usually appears due to a faulty defrost sensor, clogged drain, or a loose door gasket. It depends on the model: the technician checks the defrost cycle and the condition of the evaporator.

Who in Almaty repairs commercial and industrial refrigerators, not just household ones?

Tech Service repairs reefers, reefer containers, and commercial refrigeration equipment, not just household refrigerators. A technician arrives within 60 minutes in the city, and diagnostics are free.

Repair guideArticleTECH SERVICE08

Refrigerator Repair in Almaty by Tech Service with On-Site Technician

Author: TECH SERVICE editorial team

Published
Updated

Tech Service repairs refrigerators and refrigeration equipment in Almaty: our technician arrives at your home or site within 60 minutes anywhere in the city, diagnostics are free, and you get a 1-year warranty on labor and parts. The technician gives you the price after diagnostics, and you can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies.

Why the Refrigerator Isn't Cooling and Won't Hold Temperature

A refrigerator maintains the temperature of the cargo, so any failure in the circuit or controls is immediately noticeable. Here's what usually lies behind the symptom and what the technician checks first.

Compressor or Refrigerant Leak

When the refrigerator isn't cooling, our technician first checks the pressure in the circuit and the compressor startup, because these two causes produce a similar symptom but are fixed differently. With a refrigerant leak, the gauge shows a pressure drop on the suction side, and the compressor may hum without creating the needed pressure difference. If the pressure is normal but there's no cooling, we look at the unit itself: windings, start relay, valves. We search for leaks along the entire line—from evaporator to condenser, including brazed joints and valves, not just visible connections. Tech Service provides a 1-year warranty on labor and parts, so after fixing the leak the technician rechecks the circuit for tightness. If cooling returns for a couple of days after recharging and then disappears again, the issue isn't the amount of refrigerant but a leak in the circuit, and you need to find the leak rather than add more refrigerant.

Why It Leaks Inside and on the Floor

Water inside the chamber or on the floor usually means a clogged drain, a frosted evaporator, or a damaged door seal that lets warm moist air in. A clogged drain channel prevents condensate from draining, and moisture accumulates at the bottom of the chamber, turning into ice on the evaporator in sub-zero mode. A damaged or pinched door seal lets moist air in, which settles as frost on the evaporator, and from there water leaks onto the floor. A cracked or displaced drip tray adds its own stream to the overall picture. A leak is dangerous not only for the floor but also for the cargo: moisture and ice change the temperature regime, so before the technician arrives, it's better to move the cargo to another chamber rather than wait for the water to go away by itself.

Noise, Vibration, and Running Non-Stop

Humming and vibration in a refrigerator are rarely normal: more often they indicate wear of the fan, loose compressor mounts, or an emerging control failure that prevents the unit from shutting off. The fan loses balance over time, and its bearing starts to hum—the sound grows as it runs. Loose compressor mounts cause vibration that transfers to the frame and housing, and also accelerates wear of neighboring components. A faulty temperature sensor distorts readings, and the controls keep the compressor running longer than needed. If the refrigerator runs non-stop, don't be glad about 'good cooling': a continuous cycle accelerates compressor wear, so it's better to show this to a technician before it turns into a unit replacement.

What Types of Refrigeration Equipment We Repair

Refrigerators, reefer containers, commercial and industrial refrigerators are built differently, and the approach to restoring them differs. Here's what we work with and how servicing a transport unit differs from a household refrigerator.

How Servicing a Refrigerator Differs from a Household Fridge

A reefer unit maintains the cargo's temperature and often runs outdoors or in a vehicle, so our technician considers not only the cooling circuit but also the controls, sensors, and operating conditions that a household refrigerator doesn't have. In a transport unit, the compressor is driven by the engine or a separate generator, and the controller monitors a dozen parameters at once: chamber temperature, circuit pressure, fan speed. A home appliance lives in the stable climate of a kitchen, while a reefer faces rain, dust, and voltage spikes during startup. Because it operates outdoors, a reefer's seals and electronics wear out faster, so during a visit the technician checks not only whether it cools but also the condition of components that barely wear in a home refrigerator.

Table of equipment types and repair approach

Equipment typeWhat we check firstWhere we usually repair
Transport reeferCompressor, circuit, controlsOn site or at the service center
Reefer containerRefrigerant, sensors, ice buildupOn site, at the warehouse
Commercial refrigeratorSeal, fan, defrostOn site
Industrial cold roomCondenser, controls, sensorsOn site or at the service center
Household refrigeratorCompressor, relay, sealAt home or at the service center

Can a reefer be repaired outdoors or in a vehicle

Yes, if the issue doesn't require disassembling complex components, our mobile technician restores the equipment right on site, outdoors or in a vehicle, and it's taken to the service center when deeper work is needed. A city visit takes up to 60 minutes, diagnostics are free — the technician arrives, checks the circuit, controls, and sensors, and identifies the cause. Replacing a seal, relay, sensor, or fan is usually done on site, while brazing the circuit and replacing the compressor with subsequent refrigerant recharge require a workshop. Outdoors, it's important to provide access to the circuit and power, so before the technician arrives, clear the space around the unit; otherwise, part of the diagnostics will go into rearranging rather than finding the cause.

What an error code means and how we check the electronics

An error code on the display is a hint, not a verdict: it points to a component that's out of range. We explain what the error means and why you shouldn't reset it yourself.

What an error code on the display means

An error code shows which component the controls consider faulty but doesn't name the cause: the same code can indicate a temperature sensor, wiring, or a control board failure. The controls detect a deviation in readings and assign it a number, so the same code on two machines often leads to different faults. A sensor may give false readings due to oxidized contacts, wiring may lose signal at a splice, and the control board may show an error even when the circuit is fine. Decoding a code without checking components often misleads, so the technician first looks at sensor readings and circuit condition, and only then draws a conclusion instead of replacing a part based on a single code.

Why you shouldn't reset the error yourself

Resetting an error without diagnostics hides the cause of the fault, and the reefer continues to operate with the same issue, just without a signal on the display. The controls clear the code from memory, but the component that's out of range doesn't go away: the compressor or fan keeps running in the wrong mode, and the chamber temperature gradually drifts from the setpoint. While the error is on the screen, it hints where to look; after a reset, that clue is gone, and the technician has to check more components, which prolongs the search. If the error returns after a reset, it's a signal that it's not a one-time glitch but a component that needs checking, and repeated resets only delay the repair — sometimes until the cargo in the chamber is spoiled.

What we check if the refrigerator doesn't turn on but the light is on

If the light inside is on but the compressor won't start, our technician checks the start relay, power supply, and sensor readings, because this symptom is usually related to the compressor start rather than a complete electronics failure. The relay is responsible for starting the motor, and if it's faulty, the compressor simply doesn't get the start pulse even though there's voltage. We also check the contacts and winding integrity: a burnt terminal gives the same symptom as a dead relay. We provide free electronics diagnostics and arrive within 60 minutes anywhere in the city, and the warranty on labor and parts is 1 year. This symptom doesn't always mean the compressor needs replacing: sometimes it's enough to check the relay and contacts, so don't expect an expensive repair before diagnostics.

How refrigerator repair works on-site or at the service center

The work starts with free diagnostics and ends with a load test. We show you how the process works and when equipment is repaired on-site versus taken to the service center.

How free diagnostics works

Diagnostics are free: a specialist arrives within 60 minutes anywhere in the city, checks the circuit, compressor, sensors, and automation, identifies the cause, and then agrees on the cost of work. First, they inspect the unit and listen to how it runs, then measure the pressure in the circuit and take sensor readings, and on electronic boards they read the current parameters and compare them with the specifications. Based on the inspection, they explain which component failed and why, and show where the fault occurred. The check is needed not only to find the breakdown but also to rule out unnecessary work: often there's one cause behind "not cooling," not several, and a consistent inspection of components helps avoid replacing working parts. In our practice, the inspection takes less time than it seems—most of it goes to checking the automation.

When we repair on-site and when at the service center

On-site, we fix what doesn't require disassembling complex components, and if deep work on the circuit or electronics is needed, the equipment is taken to the service center. The decision depends not on the size of the equipment but on the component: a reefer container at a warehouse is often repaired on-site, while complex automation is easier to check at a facility with conditions for step-by-step diagnostics. The field technician brings tools for typical operations, so some faults are fixed in one visit right at your location—in the truck, warehouse, or sales floor. If the breakdown affects a sealed circuit or control board, the unit is transported to where the component can be safely disassembled and checked step by step. Moreover, transportation doesn't stretch out the work: a complex component can't be checked as accurately on-site anyway.

Repair stages from request to performance check

  • Request: you describe the symptom, we clarify the equipment type and address so we arrive prepared.
  • Visit: the specialist arrives within 60 minutes anywhere in the city, including remote areas.
  • Diagnostics: a free check of the circuit, compressor, sensors, and automation takes up most of the visit.
  • Approval: we quote the cost of work after diagnostics, and you decide whether to proceed.
  • Check: after repair, the equipment is started in operating mode under load and monitored to see if it holds temperature.

Warranty, technician experience, and why it matters when choosing a contractor

When choosing a contractor, it's important to know who will arrive and what happens to the equipment if the problem returns. Here's about the warranty, technician experience, and our direct approach.

What the 1-year warranty on labor and parts gives you

We give a 1-year warranty on labor and parts, so if the refrigerator stops cooling again after service, you come back to us instead of looking for a new technician. The warranty covers both at once: how the technician did the work and the parts they installed. In practice, a repeat visit is more often linked not to the unit itself but to a related cause that was missed on the first visit — and then we work through the situation again under the same commitment. In our experience, a year is enough time for hidden defects to show up that aren't visible when the equipment is handed back. A warranty only makes sense when it's given by the person who did the work: with a middleman, responsibility gets blurred between contractors, while with a direct contractor it's tied to a specific job.

Why a direct contractor is more reliable than a middleman

Tech Service is a direct contractor: our own technician comes to you, not a subcontractor through an aggregator, so one party is responsible for diagnostics, work, and warranty. The same specialist who diagnoses the issue then fixes it, and they're the one accountable to you for the result. With a middleman, a dispatcher sits between the request and the technician, and the service history gets split across several contractors. With us, the technician comes to your home or picks up the equipment for service and handles the job from start to finish. When there's no middleman between you and the technician, it's easier to agree on the work and come back for warranty service: you don't have to explain the history to a third party all over again. In my view, this is the point people most often overlook when choosing.

Technicians with 4 to 20 years of experience

Our technicians have 4 to 20 years of experience, so with symptoms like "not cooling" or "freezing up" they don't go by a single sign — they check components in order. The compressor, refrigerant, sensors, and electronics can all produce similar outward symptoms, and the difference only shows up in measurements. A specialist with that much experience already knows the typical combinations of symptoms for different types of equipment, so they're less likely to drift away from the real cause. Experience shows not in speed but in the fact that the technician doesn't replace parts at random: they first rule out simple causes and then tackle the complex components, which saves both time and the equipment itself. Around the city, a technician arrives within 60 minutes, and diagnostics are free — this lets us test a theory before agreeing on the work.

What to do before the technician arrives and how pricing is agreed

Before the technician arrives, there are a few simple things you can do to avoid making the breakdown worse and to keep your cargo safe. We also explain how pricing is agreed and how payment works.

Checklist: what to check yourself before the technician arrives

  • Power: check that the unit is plugged in and the contact in the socket is secure.
  • Error code: write it down or take a photo, but don't reset it before diagnostics.
  • Refrigerant: don't top up the freon yourself, because that masks a leak and throws off the search for the cause.
  • Cargo: move it to another chamber if there's free space and a working mode.
  • Access: clear the space around the unit so the specialist can get to the components right away.
  • Documents: keep the unit's model and the recorded code handy — this will speed up the check.
  • Observations: note when the fault appeared and how the equipment behaves after being turned on.

How pricing is agreed after diagnostics

The specialist gives you the price after free diagnostics, when the cause and scope of work are clear, so you agree to the work with your eyes open, not over the phone. On site, they check the compressor, refrigerant circuit, electronics, and sensors, record the fault, and explain which components need replacement and which can be restored. After that, they state the amount and break down what it consists of — labor and parts — and proceed only with your consent. This order protects you from surprises: if it turns out during the work that the cause is deeper, they'll discuss it with you before continuing, not present it as a done deal. In my view, this is exactly what you should clarify on the first call with any contractor — agreement before work starts, not after.

How fast does the technician arrive and how do I pay for the work?

The technician arrives within 60 minutes anywhere in the city, and you can pay via Kaspi QR, Kaspi Red, card, cash or bank transfer. We cover the entire area, including remote districts and industrial zones where equipment with cargo is most often located. The specialist comes with tools to check the compressor and electrical system, so diagnostics start right on site without transporting the unit to the service center. Fast arrival is especially important for a refrigerated truck with cargo: the sooner diagnostics begin, the less time the cargo spends out of operating mode. If the equipment is in a vehicle or warehouse, work is done right on site and does not require dismantling. When you call, specify exactly where the unit is located and whether there is free access to it — this saves time on site.

Key points on refrigeration unit repair

Refrigerator repair comes down to three questions: what exactly broke, where to fix it, and who is responsible for the result. Below is a short summary to help you decide before calling a technician.

  • A symptom is a clue, not a diagnosis: "not cooling" can equally mean a refrigerant leak, compressor wear, or a temperature sensor failure.
  • Equipment type matters: a refrigerated truck, reefer container, and commercial refrigerator are built differently, so the service approach differs too.
  • Don't just reset the error code: the display points to a component, but the specific cause is shown by diagnostics, not by turning it back on.
  • The scope of work depends on the component: simple faults are fixed on site, complex ones require disassembling the unit at the service center.
  • Warranty and direct contractor: responsibility for the work lies with whoever performed it, not with an intermediary between the client and the technician.

7brands

Which refrigeration unit brands we repair in Almaty

Brands with dedicated pages on the site. Follow the link to learn about repairs for a specific make.

We also repairWe also repairTECH SERVICE09

Besides refrigeration unit repair, we fix other equipment in Almaty

Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.

BlogBlogTECH SERVICE10

Worth reading before refrigeration unit repair in Almaty

Leave a review

Choose a platform — the TECH SERVICE page will open.

2ГИС2GISGoogle MapsЯYandex Maps
Send a review with photos on WhatsApp