experience9 yearsRuslan Ts.
Washing machine and refrigerator repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 746 00 26Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Free diagnostics.
Our own technicians4 to 20 years of experience




Repair prices
Below are the signs a homeowner notices before diagnostics. The exact cause is determined by the technician.
clogged drain and mold
from5 000 ₸
worn seal and loose door closure
from7 500 ₸
improper installation or compressor wear
from24 500 ₸
worn bearing, ice buildup on blades
from10 500 ₸
loose mounts or a breakdown
from10 500 ₸
clogged condenser or fan failure
from10 500 ₸
clogged drain or displaced hose
from5 000 ₸
misaligned hinge, worn seal
from7 500 ₸
The table shows how much refrigerator repair costs in Almaty for a Frigidaire: the "from" price for labor without parts and the time frame; the technician confirms the total before starting the repair.
1 visittime
from 6 500 ₸cost

BeforeAfter5 steps

From request to final check — five steps.
Tell the dispatcher your address, refrigerator model, and the symptoms.
The technician checks the unit and explains the cause and cost.
You approve the scope of work and the parts.
The technician replaces the faulty part and checks related components.
Agree on a visit time and prepare the refrigerator: clear access, defrost, and note any symptoms.
The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsField refrigerator repair technician
experience12 yearsGeneral household appliance repair technician
experience8 yearsExpert washing machine repair technician
We reply during working hours
Leave a service request — the technician will agree on a convenient time and clarify the symptoms.

Warranty question? Call us
+7 (778) 746 00 267 898 reviews of repairs at TECH SERVICE in total
Ксения И.Order No. TS-2612-282 · 29 August 2026
oursХотел сначала вызвать мастера на дом, потом передумал. Первое, что заметил: намерзает лёд. Никита М взялся за то, от чего другие отказались. Гудит ровно, не греется, всё как надо
Мирас С.Order No. TS-2641 · 13 July 2026
oursПроблема — течёт. Отдельно спосибо мастеру — Никита М, терпения ему хватило. Сделали и забыл про проблему.
Юлия А.Order No. TS-5126 · 17 April 2023
oursПробовал найти мастера в своём районе, но все были заняты. Утром столкнулся с тем, что течёт. Позвонил, описал проблему, сказали привозить — посмотрят в тот же день. Вышло дешевле нового, что логично. Из деталей — компрессор. Хороший сервис, побольше бы таких. Работает как раньше, придирок нет.
Аружан К.Order No. ZK-2416 · 24 February 2023
oursДо этого обращался в другой сервис, там только развели руками. Проблема — не морозит. Проверили при мне, показали, что всё держит.
Данияр С.Order No. TS-2205-673 · 5 April 2022
oursДруг посоветовал, у него похожая история была. С чем пришёл: не морозит. Проверили при мне, показали, что всё держит.
Алексей Г.Order No. TS-4782 · 30 August 2021
oursБыло подозрение, что дело в плате, хотелось услышать второе мнение. Приехал из командировки, а дома — шумит. В списке работ — уплотнитель. Проверил дома — всё на месте, ничего не забыли
Татьяна Б.Order No. ZK-2020/765 · 2 October 2020
oursЖалоба простая: течёт. Отдельно спосибо мастеру — Дильмурат С, терпения ему хватило. Проверили при мне, показали, что всё держит!!
Вероника П.Order No. 46065 · 7 August 2018
oursНужен был счёт и чек, у нас техника на балансе организации. Повод для визита: течёт. Проверил дома — всё на месте, ничего не забыли
Куаныш Б.Order No. 2017-1993 · 27 June 2017
oursНужен был счёт и чек, у нас техника на балансе организации. Диагностика холодильника — с этого всё началось. Повод для визита: шумит. Поставили новую деталь: компрессор. Мастер посмотрел, сказал, что возьмёться, и взялся. С тех пор ни разу не подвёл.
Ольга М.Order No. TS-1608-592 · 23 May 2016
oursТехника на гарантии уже не была, так что выбор был свободный. Позвонил узнать про ремонт холодильника. Жалоба простая: течёт. Ответили быстро, не пришлось ждать на линии. Деталь на замену — уплотнитель. Даже с учётом запчасти вышло гуманно. Цену назвали не сразу, пришлось уточнять. Если что — обращусь снова. Второй месяц — полёт нормальный.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionThe technician gives you the exact cost of replacing the refrigerant after a free diagnostic visit: it depends on the model and the scope of work. The price and the work plan are agreed with you before the repair starts.
Noise and clicking can come from the fan, the compressor, or the start relay. The technician will pinpoint the cause after diagnostics. Don't put off the visit if you hear unusual sounds.
Clear access to the back wall and unplug the refrigerator. Take out the food so the technician can run diagnostics. Don't take apart any components yourself.
Frigidaire breaks down no more often than other brands, but it does have its weak spots. The most common issues are faulty defrost sensors, the start relay, and the control board. The specific set depends on the model and operating conditions.
A cracked evaporator is usually replaced rather than repaired, since refrigerant leaks through the crack. The technician makes the call after an at-home diagnostic. Whether replacement is possible and how it's done depends on the model.
Tinkering with Frigidaire components yourself can cause a refrigerant leak and damage the control board. The only safe step is to unplug the appliance and not take it apart. Leave the rest to the technician.
Tech Service repairs Frigidaire refrigerators in Almaty: our technician arrives at your home within 60 minutes anywhere in the city or takes the appliance to our service center. Diagnostics are free, we provide a 1-year warranty on labor and parts, and you can pay via Kaspi QR, Kaspi Red, bank card, cash or bank transfer for companies. The technician quotes the price after free diagnostics.
A Frigidaire refrigerator may stop cooling for various reasons — from a sensor failure to a refrigerant leak. Let's break down what the symptoms and error codes mean and when you need a technician.
If the light inside is on but there's no cold, the refrigerator is receiving power — so the problem is inside the cooling circuit or in the compressor control. A working motor starts in short cycles and turns off when the temperature sensor signals. When it hums continuously and the tubes on the back panel are warm only near the outlet, the refrigerant isn't circulating. The thermostat only turns things on and off — if it fails, the compressor either stays silent or runs nonstop. The control board distributes signals between the sensors and the motor, and its failure produces the same picture as a mechanical fault. If the compressor hums continuously but the walls don't get cold, this more often points to a refrigerant leak or a clogged capillary tube — you can't fix that yourself.
| Code | What it means | What we check |
|---|---|---|
| E1 | Fridge compartment sensor failure | Circuit and connector |
| E2 | Freezer compartment sensor failure | Readings and wiring |
| E3 | No Frost system malfunction | Defrost heater and timer |
| E4 | Control board error | Power supply and traces |
| E5 | Airflow problem | Fan and damper |
Ice on the back wall and running without stopping are usually linked to the defrost system or a temperature sensor that won't let the compressor shut off. In No Frost models, the heater and timer cycle to melt frost on the evaporator; if the element burns out or the timer gets stuck in cooling mode, ice builds up on the wall and blocks the airflow channels. A failed sensor sends incorrect readings to the board — the motor doesn't get the stop command and runs without pauses, while the compartment gets warm. After defrosting, the unit needs time to get cold again, but if the temperature hasn't recovered after a few hours, the issue isn't defrosting but a fault in the circuit or defrost system. In our experience, these symptoms most often come down to the defrost heater or the sensor — both are checked on site.
Frigidaire has its own weak spots — inverter compressors, control boards, and the No Frost system. Here's how to tell one fault from another by how the appliance behaves, without taking it apart.
If the compressor won't start and you hear clicking, the start relay or the compressor itself is to blame. If it runs nonstop and won't shut off, it's more often the thermostat or temperature sensor. A hum with periodic clicks means the unit is trying to start and failing: the windings get a pulse, but the shaft won't turn. A steady hum with no shutdowns and food freezing too much point to stuck thermostat contacts or skewed sensor readings. A silent compartment with the light on and warm air inside is a separate scenario where the start unit is at fault, not the automation. Clicking during startup attempts is dangerous for the compressor: the longer the appliance runs like this, the higher the risk of the shaft seizing, so don't put off diagnostics.
The Frigidaire inverter compressor is controlled by a board, so when a fault occurs, we check the electronics first and only then draw conclusions about the compressor itself. The power unit here is not connected directly to the mains — the electronic module sets its rotation speed, and sensors around the compartments transmit temperature readings. When the unit is silent or, conversely, hums in bursts, the cause is more often the module or a break in the sensor circuit rather than the mechanics. In our practice, such faults often masquerade as compressor failure, even though the mechanics are intact. The control board doesn't always need to be replaced entirely — we fix some malfunctions by restoring the module, and this is worth discussing with the technician before replacement. This approach preserves the factory electronics and avoids hunting for a rare component.
| Symptom | Likely cause | What we check |
|---|---|---|
| Won't turn on, clicking | Start relay, compressor | Windings, relay |
| Runs continuously | Thermostat, temperature sensor | Thermostat contacts, sensor |
| Silent, light on | Control board | Electronic module, circuit |
| Ice on evaporator | Defrost heater, timer | Heater operation, defrost cycle |
| Weak airflow, warm | Fan | Fan blade, motor |
| Freezing along door edge | Door seal | Fit, seal wear |
Some causes can be ruled out on your own in a couple of minutes — such a check saves time and helps the technician. But there are components you shouldn't touch without equipment and skills.
A Frigidaire No Frost refrigerator is defrosted completely by unplugging it, leaving the doors open until water drains, and removing ice without sharp objects. The procedure takes several hours, and you can't speed it up with a hairdryer or knife: the evaporator plastic and circuit tubes are easily punctured, and that means a refrigerant leak. Water is collected with rags and trays, and food is temporarily moved to a cool place or a thermal bag. The No Frost system removes moisture via the defrost heater and fan, so in normal operation it doesn't need manual defrosting. Ice in such a model is a signal to check the defrost unit, timer, or sensor, not just to melt the ice. If ice appears again a day after a full defrost, the cause is in parts that are checked with instruments.
Don't open the cooling circuit, touch the compressor or the control board yourself — without the right equipment and skills, that kind of intervention leads to refrigerant leaks and new breakdowns. The circuit is under pressure, and one careless move with a tube turns a minor defect into an expensive repair with a recharge. The control board is sensitive to static and incorrect testing: shorting the contacts can easily burn out a working module. The compressor requires checking the windings and start circuit with a multimeter — you can't spot that kind of defect by eye. Even replacing the start relay without checking the circuit can make the compressor problem worse, so it's best to leave those components to a technician. The line is simple: power, thermostat, door seal and defrost are your area, while refrigerant, electrics and the motor are the specialist's.
We start Frigidaire refrigerator repair in Almaty with free diagnostics at your home — here's a step-by-step look at what the technician does and when the appliance is taken to the service center.
During free diagnostics, the technician checks the power supply, compressor operation, sensors and defrost system, reads error codes and identifies the cause of the fault. First he inspects the outlet and power cord, then listens to the motor start and measures the winding parameters, after which he moves on to the evaporator and defrost heaters. Error codes are read from the control board separately — they narrow the search down to a specific component. In my experience, more than half of all calls are resolved at this stage: the cause is clear from how the compressor runs and what the sensors show, without taking the whole unit apart. Diagnostics at home shows whether the refrigerator can be fixed on site or needs repair at the service center — this saves time and lets us discuss the scope of work right away.
To book a technician, leave a request — we'll agree on a convenient time, and the specialist will arrive at your home within 60 minutes anywhere in the city. You can submit a request in any convenient way, and payment is accepted by all methods. Tell us the Frigidaire model and the error code if it's shown on the display — this helps the technician bring the right tools and figure things out faster on site. Our technicians have 4 to 20 years of experience, and there's a 1-year warranty on labor and parts. Before the visit, clear access to the back of the refrigerator: diagnostics will take less time, and the technician can get straight to checking components without moving furniture or shifting food around.
Frigidaire stands out for its inverter compressors and electronics, so guesswork is risky here — we explain why specialization matters and what brand knowledge brings.
Frigidaire often comes with an inverter compressor and an electronic control board, so a one-size-fits-all approach without electronics know-how leads to diagnostic mistakes. In these models, the mechanics are inseparable from the control board: the compressor receives commands from the inverter, and sensor or winding failures produce similar symptoms—weak cooling while the motor runs. A technician without experience with this brand often starts by replacing the compressor, even though the real cause is the control board or a broken sensor circuit. Checking the electronics takes longer than inspecting the mechanics, but that's what separates a real fault from a false one. Someone who knows the brand recognizes typical Frigidaire failures faster and doesn't replace working parts "in a chain." In my view, it's cheaper to test the board once than to replace a working compressor twice.
Our technicians have 4 to 20 years of experience, and Tech Service is a direct service provider with its own staff, not an intermediary. That kind of experience means the person has worked on inverter models and their electronics not from a manual but on real machines: they know how the board behaves when voltage drops and how compressor symptoms differ from a sensor failure. A direct service provider means our own employee comes to your home, not a subcontractor with someone else's responsibility. The same service that sent the technician is responsible for the work—this makes it easier to resolve warranty issues, and we provide a 1-year warranty on labor and parts. Diagnostics are free, we arrive within 60 minutes anywhere in the city, and the price is quoted after the inspection. You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies.
A warranty and clear terms are as much a part of the service as the work itself. Here's what we provide after fixing the problem and how payment works, so you're left with no uncertainties.
We provide a 1-year warranty on labor and parts, including Frigidaire refrigerator compressor replacement. The coverage applies to both the part and the technician's work: if the same component fails again, the repeat repair is handled under the warranty. This covers the compressor—the most heavily loaded part in the cooling system—as well as the control board and thermostat, which we replace when a fault is confirmed. Our technicians have worked with this brand for 4 to 20 years, so they know which components tend to fail again and which last. The part is also covered, so if the same component fails again, the issue is resolved under the warranty without arguments. In my view, it's the parts coverage, not just the labor, that removes the owner's main worry after an expensive repair.
The technician quotes the price after free diagnostics, once the cause of the breakdown and the scope of work are clear, and you can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies. The inspection costs nothing: the specialist arrives, finds the fault, and only then tells you what needs to be done and for how much. This way you don't pay for the check and know in advance what you're paying for—no hidden fees during the repair. We arrive within 60 minutes anywhere in the city, so you can approve the work and payment in a single visit. If the proposed option doesn't work for you after the inspection, you don't owe anything for the check itself—the visit and diagnostics are free. Payment via Kaspi QR, Kaspi Red, card, cash, or bank transfer is convenient whether we come to your home or you bring the appliance to our service center: you choose how to pay.
Frigidaire refrigerator repair comes down to pinpointing the faulty component: by symptom, error code, and diagnostic results. Below is a quick summary to help you understand the likely scenario in advance.
90brands
We work with every brand sold in Kazakhstan — from Samsung, LG and Atlant to Biryusa, Indesit, Stinol and rare imported makes. Can’t find yours in the list? Call anyway — a technician will come and take a look.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your refrigerator stops working, first check the outlet, the power cord, and the thermostat setting, and after defrosting let it stand for a while.
4 February 2026 · 12 minutes read
If your refrigerator isn't cooling but the light is on, the cause is usually one of the components in the cooling circuit: the compressor, thermostat…
10 December 2025 · 13 minutes read
If your dishwasher won't drain, the most common culprits are a clogged filter or drain hose; less often, it's the pump, impeller…
24 March 2026 · 12 minutes read
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
If your microwave isn't heating but the light and turntable still work, the problem is usually one of the high-voltage components — the magnetron, diode…
15 February 2026 · 12 minutes read












