Original
Manufacturer's compressor
- Compatibility
- Full match for the refrigerator model
- Selection
- By part number or model
- Delivery time
- Confirmed by the technician
- Price
- After diagnostics
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 746 00 26Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city, diagnostics are free, and you get a 1-year warranty on labor and parts.
Our own technicians4 to 20 years of experience




1 yearwarranty on labor and parts
60 minutestechnician arrival anywhere in the city
freediagnostics
Compressor replacement is more than just installing a new part. The technician removes the old unit, replaces the filter drier, vacuums the system, recharges the refrigerant, and checks for leaks. The cost of work is agreed after free diagnostics.
01
Step 1removal
The technician unplugs the refrigerator, disconnects the tubes, and removes the old compressor's mounts.
02
Step 2installation
The new compressor is installed in its place, connected to the tubes, and checked for proper fit.
03
Step 3filter
The filter drier is replaced to remove moisture and contaminants from the circuit before recharging.
04
Step 4vacuum
The system is vacuumed to remove air and residual moisture so the refrigerant works efficiently.
05
Step 5recharge
The technician recharges the refrigerant, checks the connections for leaks, and tests the refrigerator.
5
The compressor is the heart of the refrigerator. If it won't start or runs nonstop, it won't stay cold. Here are five symptoms that most often prompt a service call.
Refrigerator isn't cooling
The compartments stay warm, but the light and fan work. This points to a compressor failure or refrigerant leak.
Compressor is humming
You hear a hum but there's no cold. The cause may be a start relay or a seized compressor.
Refrigerator starts then stops
The motor starts and immediately cuts out. This indicates a faulty start relay or compressor windings.
Clicking on startup
You hear clicking, and the compressor immediately cuts out. This indicates a faulty start relay or windings.
Compressor is hot
The compressor body heats up more than usual. The cause is overheating due to wear or ventilation problems.
Note how often and under what conditions the symptom appears — this will help the technician find the cause faster.
Describe the symptomsWhen replacing the compressor, the technician will offer an original part or a compatible equivalent. Selection is based on the part number or refrigerator model.
Original
or
Equivalent
The table shows refrigerator compressor replacement costs: a starting labor price without the part and the time it takes, with the final amount agreed with the technician before any work begins.
1–2 hourstime
from 11 500 ₸cost

BeforeAfterThe home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsField refrigerator repair technician
experience12 yearsGeneral household appliance repair technician
experience8 yearsExpert washing machine repair technician
We reply during working hours
Leave a request — a technician will arrive within 60 minutes anywhere in the city. 1-year warranty on labor and parts.

Warranty question? Call us
+7 (778) 746 00 267 898 reviews of repairs at TECH SERVICE in total
Ксения И.Order No. TS-2612-282 · 29 August 2026
oursХотел сначала вызвать мастера на дом, потом передумал. Первое, что заметил: намерзает лёд. Никита М взялся за то, от чего другие отказались. Гудит ровно, не греется, всё как надо
Мирас С.Order No. TS-2641 · 13 July 2026
oursПроблема — течёт. Отдельно спосибо мастеру — Никита М, терпения ему хватило. Сделали и забыл про проблему.
Юлия А.Order No. TS-5126 · 17 April 2023
oursПробовал найти мастера в своём районе, но все были заняты. Утром столкнулся с тем, что течёт. Позвонил, описал проблему, сказали привозить — посмотрят в тот же день. Вышло дешевле нового, что логично. Из деталей — компрессор. Хороший сервис, побольше бы таких. Работает как раньше, придирок нет.
Данияр С.Order No. TS-2205-673 · 5 April 2022
oursДруг посоветовал, у него похожая история была. С чем пришёл: не морозит. Проверили при мне, показали, что всё держит.
Татьяна Б.Order No. ZK-2020/765 · 2 October 2020
oursЖалоба простая: течёт. Отдельно спосибо мастеру — Дильмурат С, терпения ему хватило. Проверили при мне, показали, что всё держит!!
Бекзат Т.Order No. ZK-2020/226 · 1 August 2020
oursСмотрел, у кого есть запчасти на такую модель. Обидно было, техника не старая совсем. С чем пришёл: намерзает лёд. Никита М возился с этим дольше, чем планировал, но довёл до конца. Сделали и забыл про проблему.
Вероника П.Order No. 46065 · 7 August 2018
oursНужен был счёт и чек, у нас техника на балансе организации. Повод для визита: течёт. Проверил дома — всё на месте, ничего не забыли
Павел Ш.Order No. 2018-7272 · 9 January 2018
oursСимптом был очевидный: шумит. Дильмурат С честно сказал, что менять, а что ещё походит. Шум пропал, работает мягко.
Куаныш Б.Order No. 2017-1993 · 27 June 2017
oursНужен был счёт и чек, у нас техника на балансе организации. Диагностика холодильника — с этого всё началось. Повод для визита: шумит. Поставили новую деталь: компрессор. Мастер посмотрел, сказал, что возьмёться, и взялся. С тех пор ни разу не подвёл.
Ольга М.Order No. TS-1608-592 · 23 May 2016
oursТехника на гарантии уже не была, так что выбор был свободный. Позвонил узнать про ремонт холодильника. Жалоба простая: течёт. Ответили быстро, не пришлось ждать на линии. Деталь на замену — уплотнитель. Даже с учётом запчасти вышло гуманно. Цену назвали не сразу, пришлось уточнять. Если что — обращусь снова. Второй месяц — полёт нормальный.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionA faulty compressor shows up as no cooling even though the light is on, silence instead of the usual hum, and a cold motor housing after it tries to start. But a start relay can cause similar symptoms, so a technician makes the final call after free diagnostics.
Humming without starting usually means the motor isn't turning: the compressor is seized or the start relay has burned out. It depends on the model, so the technician checks the relay and windings first, then decides whether the compressor needs replacing.
If you hear clicks when it turns on, the motor doesn't start, and the compressor housing stays cold, it's most likely the relay. When the compressor hums but doesn't cool, or stays silent and doesn't respond to starting, it's probably faulty — the technician will know for sure after taking measurements.
In household refrigerators the compressor is usually sealed, so when it wears out or seizes it's replaced as a whole. Only some models allow partial repair, and after free diagnostics the technician will tell you what fits your case.
The replacement itself with refrigerant recharge usually takes a few hours, but the exact time depends on the model and the condition of the refrigerator. The technician does the work at your home, so you can watch the process.
If the refrigerator is modern and in good condition, replacing the compressor will extend its service life. But with heavy wear or an expensive inverter compressor, it's sometimes more cost-effective to buy a new refrigerator — the technician will advise after diagnostics.
Tech Service replaces refrigerator compressors in Almaty at your home or at our service center. A technician arrives within 60 minutes anywhere in the city, diagnostics are free, and we give you the price after diagnostics. We provide a 1-year warranty on labor and parts. Our own technicians with 4 to 20 years of experience do the work, not subcontractors.
The motor-compressor is the heart of the cooling system, but similar symptoms can come from the start relay, temperature sensor, or refrigerant leak. That's why we decide on replacement only after taking measurements, not based on a single sign.
During free diagnostics, our technician measures the motor windings, checks the start relay, thermostat, and pressure in the circuit, and only after reviewing all measurements concludes whether replacement is needed. Resistance is compared with the specification for the specific model: a discrepancy or open circuit points to the motor, while intact windings with no cooling shift the search to a refrigerant leak and sensors. The start relay is removed and tested separately—this part is cheaper than the motor and often fails before it. The thermostat is checked with a continuity tester at different temperatures. If the refrigerator clicks every couple of minutes and doesn't start, the start relay is usually to blame, not the motor—so don't agree to replace the unit without seeing the measurements. If you're looking for refrigerator compressor replacement price in Almaty, the technician gives it after free diagnostics.
The motor-compressor most often wears out due to overheating from poor airflow, voltage spikes, stuck valves, and natural wear over years of use. A rear grille against a wall or in a niche doesn't dissipate heat, the housing overheats, oil loses its properties, and the wiring shorts out. A power surge finishes off the start winding—it's the thinnest and the first to break. Stuck valves cause weak cooling while the unit runs: it hums but doesn't build the required pressure in the cooling circuit. Natural wear accumulates over years—the life of bearings and the valve group is not infinite. Regular defrosting of the refrigerator and free space around the rear grille extend the motor's life more than any repair after a breakdown.
| Symptom | Points to | What we check |
|---|---|---|
| Humming without cooling, hot housing | Motor-compressor | Winding, starting current |
| Clicking every couple of minutes | Start relay | Contacts, winding |
| Runs but compartment is warm | Refrigerant leak | Pressure in the circuit |
| Ice on the evaporator | Thermostat or sensor | Continuity test of sensors |
| Unit is silent, no light | Power supply or thermostat | Power circuit |
We do the work at your home without taking the appliance to the service center. A technician arrives within 60 minutes anywhere in the city, and the owner should decide in advance where to put the food during the work.
The part is chosen not by eye but by motor type, cooling capacity, and refrigerant. Inverter models follow different rules, and you should know this before approving the work.
| Compressor type | What we consider when selecting | Replacement specifics |
|---|---|---|
| Reciprocating for R600a | Power, mounting dimensions, start relay | Requires circuit evacuation |
| Reciprocating for R134a | Operating pressure, chamber volume | Different refrigerant charge |
| Inverter | Compatibility with control board | Check electronics before installation |
| For No Frost | Capacity and evaporator airflow | Monitor defrost after installation |
An inverter unit is replaced with attention to the control board and sensors — our technician checks the electronics so the new motor doesn't fail due to a faulty inverter. This unit smoothly adjusts speed instead of hard on/off cycles, so it has specific requirements: compatibility with the board, a working temperature sensor, and correct readings at startup. During installation, we check cooling in both compartments and how the electronics behave in several modes — from pulling down temperature to shutting off. Our technician selects the part by motor type, cooling capacity, refrigerant, and mounting dimensions, so a component from another model doesn't always fit. If the board isn't checked after installation, the error on the display will return — first diagnose the electronics, then replace the part. A unit with the wrong power will technically start but will run at its limit and overheat, so saving on selection leads to repeat repair. We discuss the cost of this work with the technician after free diagnostics.
The unit is rarely repaired — it's replaced. But before installing a new part, weigh the age of the appliance, motor type, and condition of the circuit so the decision is informed and doesn't lead to another technician visit.
In most cases, repair comes down to installing a new motor-compressor, because the winding and valves can't be restored on-site — we replace the part entirely. Sticking valves and interturn winding shorts in a sealed housing can't be fixed by soldering: the housing is only opened at the factory, and after opening on-site the unit loses its seal. Our refrigerator repair for this fault involves installing a new compressor with the same mounting base and tubing for soldering, followed by circuit evacuation and refrigerant charging. Our technician does the work on-site; you don't need to take the unit to a service center. If a technician offers to fix the motor without installing a new part, ask what exactly they're doing: a sealed unit has almost no repairable parts.
If the refrigerator is old, the cooling circuit is damaged by corrosion, and the control board needs replacement, installing a new unit may not be worth it compared to buying a new appliance. Rust on the evaporator and refilling refrigerant through a corroded pipe lead to repeat leaks, and failed electronics add another component to the job. Diagnostics help distinguish a faulty motor from a relay and from refrigerant leaks — without them, it's easy to replace a working part and still not fix the cause. The decision isn't based on the age of the appliance but on the overall picture: the condition of the circuit, the electronics, and the total scope of work. The technician gives the price after free diagnostics, and you can compare it with a quote for a new appliance before agreeing to compressor repair — in this case, the cost only becomes clear after the inspection.
Warranty and transparency set a direct contractor apart from a middleman. Here's what the warranty covers and why trying to replace the unit yourself ends up costing more.
DIY repair requires vacuuming the circuit, precise refrigerant charging, and brazing — without experience, it's easy to damage the motor and the cooling circuit. You can't just pour in refrigerant: before charging, the circuit is vacuumed to remove air and moisture, otherwise acids form inside and destroy the new unit's winding. Brazing a sealed joint also takes skill: an underheated seam leaks, while overheating damages the tubes and nearby parts. After installation, commissioning is needed — checking pressure, current, and temperature, otherwise the motor runs in the wrong mode and wears out quickly. A mistake in refrigerant dosage or moisture in the circuit leads to another breakdown faster than the savings on a technician: the second repair costs more than the first, and the new unit may fail again. If you're looking for refrigerator repair compressor replacement price, the technician gives it after free diagnostics.
We've gathered the key points about compressor replacement — from diagnosis to checking the cold after reassembly. This short list helps you make a balanced decision.
If you ask, the technician will check other parts during the same visit.
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
If your refrigerator stops working, first check the outlet, the power cord, and the thermostat setting, and after defrosting let it stand for a while.
4 February 2026 · 12 minutes read
If your refrigerator isn't cooling but the light is on, the cause is usually one of the components in the cooling circuit: the compressor, thermostat…
10 December 2025 · 13 minutes read
If your dishwasher won't drain, the most common culprits are a clogged filter or drain hose; less often, it's the pump, impeller…
24 March 2026 · 12 minutes read
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
If your microwave isn't heating but the light and turntable still work, the problem is usually one of the high-voltage components — the magnetron, diode…
15 February 2026 · 12 minutes read