Original
Pump from the machine manufacturer
- Compatibility
- By part number and machine model
- Lifespan
- Designed for factory loads
- Noise level
- Matches the machine's specifications
- Price
- Usually higher than an analog
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 746 00 26Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes, free diagnostics, 1-year warranty on labor and parts. The pump is matched to your machine model.
Our own technicians4 to 20 years of experience




60 minutestechnician arrival
1 yearwarranty on labor and parts
freediagnostics
Replacing a pump is not just about taking out the part and putting in a new one. The technician drains the water, checks the filter and hoses, installs the new pump, and runs a test cycle. The price is quoted after free diagnostics.
01
Step 1on site
The technician drains the remaining water through the emergency hose, removes the filter, and checks it for clogs.
02
Step 2on site
Disconnects the hoses, removes the mounts, and takes out the pump without damaging nearby parts.
03
Step 3on site
Installs a compatible pump, connects the plug, and checks that it sits securely in place.
04
Step 4on site
Inspects hoses for cracks, rinses the filter, and checks connections for leaks.
05
Step 5on site
Runs a short program to make sure water drains and the pump runs without humming.
5
Five symptoms that mean you should check the drain. The cause is not always the pump: the technician first checks the filter, hose, and pipes.
Water stays in the drum
After washing, water doesn't drain and the drum stays full. The machine may not unlock the door until it's fully drained.
Puddle while draining
If water appears under the machine during draining, most often the pump connections, hoses, or drain hose are not sealed.
Won't spin, stands with water
The cycle stops before spinning, and the machine stops with water in the drum. Until the water is drained, spinning won't start.
Hums but water won't drain
The pump motor runs, you can hear a hum, but there's no drainage. A common cause is a clogged filter or a foreign object near the impeller.
Door locked after washing
The lock stays engaged because the drain didn't finish. The machine won't unlock the door while there's water in the drum.
Note the error code and machine model before calling the technician — this will speed up diagnostics.
Describe the symptomsPick the pump by part number or model. An original fits exactly; an aftermarket one is cheaper — check its mount and connector.
Original
or
Aftermarket
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1 visittime
from 4 500 ₸cost

BeforeAfterThe home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsExpert washing machine repair technician
experience8 yearsSenior washing machine repair technician
experience9 yearsWashing machine repair technician
We reply during working hours
Leave a request — the technician will arrive within 60 minutes anywhere in the city, check the drain and pump for free, and quote the price before starting work.

Warranty question? Call us
+7 (778) 746 00 266 064 reviews of repairs at TECH SERVICE in total
Ринат Х.Order No. 920200 · 7 October 2026
oursИскал мастерскую поближе к дому, чтобы не мотаться с техникой через полгорода. Жена сказала выкинуть, я решил сначала показать мастеру. Проблема — не включается. Дима возился с этим дольше, чем планировал, но довёл до конца. Диагностику сделали бесплатно, хотя я был готов платить. Разобрали, посмотрели: модуль управления. Сравнивал с двумя другими — здесь вышло ровнее всех. Хороший сервис, побольше бы таких. Сказать, что доволен — ничего не сказать)
Наталья С.Order No. 929586 · 27 December 2023
oursПовод для визита: ошибка на дисплее. Рустем Т снял деталь, показал износ, вопросов не осталось. Нагрев в норме, постороних звуков нет.
Индира П.Order No. ZK-2023/233 · 26 July 2023
oursЦена имела значение, но и гарантия тоже. После выходных обнаружил: не греет воду. Диагностику сделали бесплатно, хотя я был готов платить. Проверил дома — всё на месте, ничего не забыли
Тимур И.Order No. 54448 · 25 January 2023
oursПроблема — не отжимает. Рустем Т честно сказал, что менять, а что ещё походит. Сказать, что доволен — ничего не сказать.
Жасмин Р.Order No. ZK-2021/689 · 13 June 2021
oursРустем Т помог выбрать, без навязывания. Мастер сам перезвонил, когда появилась запчасть. Ребёнок уже проверил на прочность, держиться.
Анна Т.Order No. 405199 · 12 November 2019
oursПервое, что заметил: не отжимает. Отдельно спасибо мастеру — Рустем Т, терпения ему хватило. Нагрев в норме, посторонних звуков нет
Серик М.Order No. 2018-6434 · 18 June 2018
oursОтдельно спасибо мастеру — Рустем Т, терпения ему хватило. Вернули в тот же день, всё функционирует)
Жасмин Р.Order No. ZK-2017/344 · 3 June 2017
oursСмотрел, у кого есть запчасти на такую модель. Первое, что заметил: не греет воду. Вернули в тот же день, всё функционирует.
Ксения И.Order No. ZK-6865 · 9 January 2017
oursХотел сначала вызвать мастера на дом, потом передумал. Гудит ровно, не греется, всё как надо.
Дмитрий Л.Order No. ZK-9878 · 29 October 2016
oursБыло важно, чтобы сделали до выходных — гости, то-сё. До последнего откладывал, но пришлось признать: не отжимает. Отдал 22 000, и это вместе с работой. Созвонились, договорились на удобное время, никто не тянул. В списке работ — модуль. Нагрев в норме, посторонних звуков нет.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionSigns of a faulty pump include water left in the drum after the wash, no spin cycle, and a humming sound without draining. The machine may show a drain error code, which varies by model.
First unplug the machine and drain the water through the emergency hose behind the service panel. Then remove the panel, disconnect the terminals and hoses, and unscrew the pump mount. The exact procedure depends on the model.
Most often debris like a coin, lint, or a small object has jammed the impeller, so it can't spin. Less commonly, the pump itself is worn out. A technician checks whether the impeller turns freely and decides whether to clean or replace it.
Yes, the drain pump is usually mounted at the bottom and can be accessed without opening the drum, so a sealed drum doesn't prevent replacement. It's more difficult if the mount is non-standard, in which case the part is matched by number or model code.
A drain code on older Bosch series (Maxx, Classixx, Logixx) indicates a draining problem, but the pump isn't necessarily to blame. First check the filter at the bottom front and the hose, and only then the pump.
The main cause of pump failures is debris: coins, lint, small objects, and a clogged filter. Scale has little effect on pump wear, so regular filter cleaning extends its life.
Tech Service replaces washing machine drain pumps in Almaty with a technician visit to your home within 60 minutes. Diagnostics are free, and you get a 1-year warranty on labor and parts. We work as a direct contractor, no middlemen: our technician comes to you or repairs it at our service center.
"Not draining" doesn't always mean the pump. Here's how to tell a clogged filter and hose from a pump that's actually failed, and why a multimeter won't show a jammed impeller.
We start washing machine pump repair in Almaty by checking the simple things: filter, hose, pipes. In most cases "not draining" is a clogged drain filter behind the service flap at the bottom front or a kinked hose, and leaks from below are more often caused by pipes than by the pump itself. The mesh gets clogged with lint and small items, the hose gets kinked when the machine is moved or clogged at a bend, and pipes crack over time and drip under the machine. The drain code stays the same, so you can't tell from the error on the display what to replace — the code's meaning depends on the model, and the technician checks it against the table for your machine. A leak at the door is the seal, not the pump, and it's replaced separately. A multimeter won't show a jammed pump — you check whether the impeller turns freely; so just "testing" the pump and stopping there is a common mistake. Washing machine pump replacement cost depends on the model and the pump itself, and the technician gives you the exact price after free diagnostics.
The code on the display narrows the search but doesn't make a diagnosis. Below are the codes that most often point to a water drainage problem, with a caveat: the meaning depends on the model, and the technician checks it against the table for your machine.
| Brand or series | Drain problem code |
|---|---|
| Bosch, Siemens (current Serie 2/4/6/8) | E18 |
| Bosch, Siemens (older Maxx, Classixx, Logixx, Avantixx) | F18 |
| Samsung | 5E (SE, E2) |
| Electrolux | E20 |
| Indesit, Hotpoint | F05 |
We cross-check the code against the table for the specific model: the same F18 can mean a clogged filter, a failed pump, a pressure switch fault, or a triac failure on the drain control module. On Samsung, code 5E is often caused by a lint-clogged hose rather than the pump itself, while on Indesit F05 technicians check the pressure switch first. That's why we don't order a part based on the code alone — we first check whether the impeller spins freely and whether water drains through the hose, and only then select a pump by part number or model code. On Bosch, the part number is taken from the E-Nr rating plate inside the door. On models without a display, the code is shown by indicator lights, and the interpretation depends on the combination of lights. Replacing a part "by code" without checking the components often leads to a repeat repair, and our free diagnostics are exactly what helps distinguish a clog from a pump failure. If the check shows the pump needs replacing, our technician in Almaty selects the right part for your model.
A machine full of water requires care. Below is a safe step-by-step procedure and an explanation of what not to do to avoid flooding the floor or getting burned.
If the machine fails to drain again on the next wash after you've drained the water, it's no longer a one-off — our technician arrives within 60 minutes anywhere in the city and determines on the spot whether it's the filter, hose, or pump. Tech Service specialists work with various brands, so they check both the impeller and hose patency rather than replacing parts blindly. Diagnostics are free, and the technician gives you the price after inspection — no figures over the phone. The cost of replacement depends on the model and the part itself; the exact amount is given after free diagnostics. The price for washing machine pump repair depends on the model and the part itself; the exact amount is given after free diagnostics. Don't unscrew the filter "on the fly" and don't take the pump apart: water under pressure will spill onto the floor, and without experience it's easy to damage the impeller or seal. That's why attempting to "finish" the disassembly yourself often costs more than calling a specialist right away.
Work with access from the bottom of the machine and selection of a compatible part. Here's how we do it: from the visit to checking the drain after the work.
We match the pump by part number or model code — on Bosch machines, that's the E-Nr on the sticker inside the door, so the part is compatible with your washer. We'll tell you how much a washing machine pump repair costs after a free diagnostics — no prices over the phone. Compatibility matters more than the name: a pump with the right connector and mounting fits without modifications, while a "similar" one may not sit in the mounting points. We also check separately whether the impeller on the old pump spins freely — a multimeter won't show a jammed pump; you need a visual inspection. It's also important to understand: the bearing is replaced only if the tub is serviceable, and "worn brushes" applies only to brushed motors — inverter Bosch EcoSilence Drive and LG Direct Drive motors have no brushes, and that changes the list of work. That's why the technician checks the model code against the table for your machine before quoting the scope of repair.
| Format | Where it's done | What's included |
|---|---|---|
| At your home | At your place | Arrival within 60 minutes, free diagnostics, replacement, drain check |
| At the service center | At our place | Free diagnostics, replacement, drain check |
| Warranty | Both formats | 1-year warranty on labor and parts |
Warranty and price are the two questions we get most often. Here's a straight answer: what the warranty covers, where DIY repair ends, and what determines the final amount.
We provide a 1-year warranty on labor and parts. You can replace the pump yourself, but with a non-serviceable tub and no experience, the risk of damaging the impeller or seal outweighs the savings. On most models, the pump is mounted at the bottom behind the service panel, so access doesn't require disassembling the tub. The difficulty starts further: with a non-serviceable tub, the bearing isn't replaced separately, and if you remove the clamp carelessly, the hose can crack and add a new part to the repair. Our technicians do this work with a post-installation drain check — that's how we see whether the connection holds and water drains properly. If a drain error remains after a DIY attempt, the cause may not be the pump but the pressure switch or the triac on the module — and then the part was replaced for nothing.
The cost consists of the part itself and the labor, and the technician gives the exact amount after a free diagnostics — quoting a figure before that wouldn't be fair. The total depends on the part number: the spare part is selected by model code or article number; on Bosch it's the E-Nr on the sticker inside the door, and different series come with different pumps. The second part is the labor to access the unit, which is higher for a non-serviceable tub than for a machine with a removable panel. That's why the cost of washing machine pump repair in Almaty isn't a fixed amount for all models: it depends on access to the unit and the pump series. The technician calculates the exact amount after inspection. Diagnostics doesn't increase the total: it's free, and you can pay via Kaspi QR, Kaspi Red, bank card, cash or bank transfer for companies.
Here's the key information about washing machine pump replacement: from the first symptoms to what the warranty covers and why free diagnostics matters.
If you ask, the technician will check other parts during the same visit.
Refrigerator Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
Washing machine error codes are self-diagnostic codes that point to a specific component: drain, water fill, heating, motor, or door lock.
29 January 2026 · 13 minutes read
If your washing machine won't spin, it's usually an unbalanced load, a clogged drain filter or hose, and less often the pump, belt…
19 January 2026 · 12 minutes read
If your washing machine isn't heating water, the heating element or temperature sensor is usually to blame, less often the control board or wiring.
25 December 2025 · 12 minutes read
If your washing machine won't turn on, first check the outlet, extension cord, and the circuit breaker in your panel, then the plug and power cord.
24 November 2025 · 13 minutes read