Open until 19:00+7 (778) 021 13 16Call a technician
Tech Service technician next to a hoverboard

Hoverboard Repair in Almaty

A technician arrives within 60 minutes anywhere in the city. Diagnostics are free.

  • 1-year warranty on labor and parts
  • 4 to 20 years of experience

Our own technicians4 to 20 years of experience

Ruslan Ts.Damir M.Dilmurat S.Dima

Repair prices

  • Diagnostics0 ₸
  • Contact solderingfrom2 000 ₸
  • Calibration and balancingfrom2 500 ₸
  • Lighting replacementfrom2 500 ₸
  • Battery replacementfrom3 500 ₸
All prices
2ГИСЯours4,97 898 reviews
2GIS · Google · Yandex · order database
Common faultsCommon faultsTECH SERVICE02

Common hoverboard faults in Almaty

Below are the common symptoms hoverboard owners come to us with. The technician finds the exact cause during free diagnostics.

PricesPricesTECH SERVICE03

How much hoverboard repair costs in Almaty

The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.

Contact solderingexact price — after the free diagnostics

1–2 days

from2 000 ₸

Calibration and balancingexact price — after the free diagnostics

1–3 hours

from2 500 ₸

Lighting replacementparts not included

1–3 hours

from2 500 ₸

Battery replacementparts not included

1–2 hours

from3 500 ₸

Power button replacementparts not included

1–2 hours

from3 500 ₸

Before and afterBefore and afterTECH SERVICE04

Before and after hoverboard repair in Almaty

Battery does not charge

1–2 hourstime

from 3,500 ₸cost

Problem
The hoverboard stopped charging: the charging indicator does not respond, and when connected to power the device shows no signs of life.
What we did
The technician checked the charging circuit and found a swollen battery with a melted connector and corrosion on the terminals. Replaced the battery and checked the wiring insulation.
Result
The hoverboard charges normally, the indicator shows charging, and the device works when turned on. The technician checked the basic functions.
I want the same
Hoverboard: battery does not charge — after repairBeforeAfter
01 / 03
All repairs
TECH SERVICE mobile technician with a tool case

How hoverboard repair works at your home in Almaty

Five steps from your request to checking the board after repair.

  1. Requestby phone

    Leave a request and describe the symptom and the hoverboard model.

  2. Visitin 60 minutes

    The technician comes anywhere in the city to inspect the board on site.

  3. Diagnosticsfree

    The technician checks the battery, board and hub motors and names the cause.

  4. Approvalright after

    You approve the scope of work and the cost, and the technician starts the repair.

  5. Handoverafter repair

    The technician agrees on the timing and handover of the board after repair.

Leave a request
TechniciansTechniciansTECH SERVICE05

Our home appliance repair technicians in Almaty

The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

  • 8 technicians in Almaty
  • 8–12 years of experience in the department
  • Article author Ruslan Ts., 9 years of experience
Mobile technician fixing a washing machine at the customer's home
Field technician at a customer’s home

The department has 8 specializations — they are listed on the technicians' cards.

01 / 08
Ruslan Ts., washing machine and refrigerator repair technicianexperience9 years

Ruslan Ts.

Washing machine and refrigerator repair technician

Damir M., general household appliance repair technicianexperience12 years

Damir M.

General household appliance repair technician

Dilmurat S., field technician for washing machine and refrigerator repairexperience10 years

Dilmurat S.

Field technician for washing machine and refrigerator repair

Dima, expert washing machine repair technicianexperience8 years

Dima

Expert washing machine repair technician

Nikita M., field refrigerator repair technicianexperience8 years

Nikita M.

Field refrigerator repair technician

Oraz, senior washing machine repair technicianexperience8 years

Oraz

Senior washing machine repair technician

Radik T., dishwasher repair technicianexperience11 years

Radik T.

Dishwasher repair technician

Rustem T., washing machine repair technicianexperience9 years

Rustem T.

Washing machine repair technician

We reply during working hours

Book hoverboard repair in Almaty

Describe the symptom and the hoverboard model when booking, so the technician can understand the likely cause before the inspection.

TECH SERVICE administrator replying to a customer's WhatsApp message

Warranty question? Call us

+7 (778) 021 13 16
Customer reviewsReviewsTECH SERVICE06

Reviews of hoverboard repair in Almaty

Индира П.Order No. 675500 · 15 October 2026

ours

Проблема — не включается. Отдельно спосибо мастеру — Максим Снегирев, терпения ему хватило. Сказать, что доволен — ничего не сказать.

Repair: hoverboard repair in

Юлия А.Order No. 47850 · 4 July 2026

ours

Друг посоветовал, у него похожая история была. Проблема — не включаеться. Сказать, что доволен — ничего не сказать

Repair: hoverboard repair in

Максим Ю.Order No. ZK-2860 · 1 June 2025

ours

Выбирал по отзывам в 2ГИС, времени на эксперименты не было. Повод для визита: не включается. Проверили на всех режимах, всё чётко

Repair: hoverboard repair in

Камила А.Order No. ZK-2077 · 7 April 2024

ours

Смотрел, у кого есть запчасти на такую модель. Сначала думал, что ерунда, но появилось: дёргается. Разобрали, посмотрели: плата. Диагностику сделали бесплатно, хотя я был готов платить. Уже полгода — ни одного сбоя.

Repair: hoverboard repair in

Фарида К.Order No. 875894 · 27 January 2024

ours

Позвонил знакомому, он раньше работал в сервисе, посоветовал этих. После выходных обнаружил: не включается. По деньгам вышло адекватно, в другом месте просили больше. Из деталей — плата. Приняли без предоплаты, это подкупило. Спасибо, выручили. Функции все на месте, ничего не отвалилось)

Repair: hoverboard repair in

Аружан К.Order No. 2023-1496 · 27 September 2023

ours

С чем пришёл: дёргается. Максим Снегирев снял деталь, показал износ, вопросов не осталось. Починили и дали гарантию на месяц.

Repair: hoverboard repair in

Сергей Р.Order No. TS-7532 · 23 August 2022

ours

Было важно, чтобы сделали до выходных — гости, то-сё. Я человек терпеливый, но тут уже думал всё. Основная жалоба — дёргаеться. Даже с учётом запчасти вышло гумано. Сказать, что доволен — ничего не сказать)

Repair: hoverboard repair in

Диана М.Order No. 116170 · 16 March 2022

ours

Хотел сначала вызвать мастера на дом, потом передумал. Диагностику сделали бесплатно, хотя я был готов платить. Пользуюсь ежедневно, вопросов нет.

Repair: hoverboard repair in

Богдан С.Order No. TS-7877 · 31 January 2022

ours

Танысым осы жерді мақтап, кеңес берді. Техника кенеттен істен шықты, қатты асығыс едім.

Repair: hoverboard repair in

Роман З.Order No. 2022-5477 · 11 January 2022

ours

Поломка застала перед командировкой, тянуть было нельзя. Диагностика гироскутера — с этого всё началось. Больше всего напрягало: дёргается. Поменяли: плата. Приехал без записи, приняли как есть. Смета совпала с итогом, что редкость. Проверили на всех режимах, всё чётко)

Repair: hoverboard repair in
Questions and answersQuestionsTECH SERVICE07

Questions about hoverboard repair in Almaty

Didn’t find the answer? Message us on WhatsApp.

Ask a question
Can I calibrate a hoverboard myself?

The owner can do a basic platform calibration following the model's instructions: place the board level and start the setup mode. If the hoverboard still pulls to one side after that, the sensors need to be checked at a service center.

Can I replace just one battery cell in a hoverboard?

Technically yes, but in practice it's not advisable: the old and new cells have different wear levels, and the battery quickly starts to perform unevenly again. A technician usually recommends rebuilding the entire pack or replacing the whole battery, depending on the model.

Is it dangerous to use a hoverboard with a swollen battery?

Yes, this is one of the most dangerous cases: a swollen battery can catch fire while charging or riding. It's best not to turn on or charge such a hoverboard and to hand it over to a technician right away for inspection and battery replacement.

Can a cracked hoverboard body be repaired, or do I need a new one?

Body cracks are usually fixable: a technician reinforces the damaged areas or replaces the body if the damage is severe, depending on the model. First, it's important to check whether the frame and steering axis were affected by the impact.

Do you repair hoverboards at home or only at the workshop?

A Tech Service technician fixes most hoverboard issues at the customer's home after free diagnostics. If complex board or battery repair is needed, the device is taken to the service center, and a visit in Almaty takes up to 60 minutes.

Can I charge a hoverboard right after coming in from the cold in winter?

No, you shouldn't charge a hoverboard right after it's been in freezing temperatures: the battery needs to warm up to room temperature, otherwise the battery may be damaged and the electronics may fail. Let the device sit in a warm place for a few hours, and only then plug in the charger.

Repair guideArticleTECH SERVICE08

Hoverboard repair in Almaty and fault breakdown by Tech Service technicians

Ruslan Ts., washing machine and refrigerator repair technician

Author: Ruslan Ts.,Washing machine and refrigerator repair technician

Published
Updated

Hoverboard repair in Almaty is done by our own technicians: one arrives within 60 minutes anywhere in the city, and diagnostics are free. We fix hub motors, gyro boards, footpad sensors, batteries and shells at your home or in our service center. Our technicians have 4 to 20 years of experience, we give a 1-year warranty on labor and parts and accept payment via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies.

What happens to the hub motor and why it hums

The hub motor is the main drive unit of the board: its hub hides the motor, bearings and rotor position sensors. Below we go through the sounds, jerks and tire marks that show exactly what has worn out and what will need replacing.

Humming, knocking and wheel play while riding

We usually trace humming and knocking from a wheel to the hub motor bearings, less often to a loose axle or a tire rubbing against the shell. The motor sits right inside the hub: a rotor with magnets spins around a fixed axle and is held by two bearings that take the rider's full weight and every hit against a curb. Once water and dust wash out the grease, the bearing first rustles, then play appears and the wheel rocks when you grab it by hand. A worn bearing produces an even hum that grows with speed. Hoverboard repair in Almaty with this symptom usually comes down to replacing the bearings and checking the axle seat, without replacing the motor itself. While it is open, we also inspect the magnets and the winding for rubbing marks. Do not put off the visit: a broken bearing lets the rotor catch the stator, and then instead of one part you have to replace the whole hub motor.

Jerking and a wheel that pulls weaker than the other

Jerks on start, twitching in place and a wheel that pulls weaker than the other point to the Hall sensors or the motor phase wires. The brushless motor is driven by the board using signals from three Hall sensors: they report the rotor position, and the controller sends current to the right winding. If one sensor fails or a thin signal wire chafes through inside the hollow axle, the motor loses sync, so it vibrates, hums in place and cuts out under load. Sensors can only be checked with the cover off: the technician measures each signal while slowly turning the wheel by hand. A burnt phase connector between the motor and the board gives similar signs, betrayed by darkened plastic and a burning smell. Hall sensors are replaced without changing the motor, usually as a full set. But the windings are checked for overheating first: a new sensor in a motor with a scorched winding only delays the next failure.

Tires and tubes for different wheels

Wheel typeTypical faultWhat we do
6,5 inch, solid tireWorn tread, cracked rubberReplace the tire on the hub motor
8 inch, solid tireChips from curbsReplace the tire, check the rim
10 inch, tube and tirePuncture, losing airReplace the tube or the tire
Off-road tireSidewall cut, bulgeReplace the tire, check the axle
Any wheel after an impactWobble, bent rimCheck the bearings and hub

Why the board loses balance and moves by itself

Balance is kept by gyro boards with tilt sensors and by the footpad sensors. When the platform drifts to one side, vibrates or moves off without a rider, look for the cause in this electronics first and only then in the frame and axle.

Calibration when the platforms sit unevenly

If one platform tilts at rest and the board drifts to one side while riding, start with calibration, which resets the tilt sensor readings to zero. The gyro board of each half carries a chip with a gyroscope and an accelerometer, and an impact, long shaking or a part replacement shifts its zero point. On many models calibration works like this: switch the power off, put the board on a level floor, align the platforms and hold the power button until the indicators blink. On app-connected models this function sometimes lives in the smartphone settings. The exact procedure depends on the firmware, so check the manual for your model. Calibrate at room temperature with the board completely still, because any touch on the platforms at that moment spoils the result. If even two or three attempts do not remove the drift, the problem is no longer the setting: look for a cracked solder joint on the gyro board or a bent central axle from a fall.

Vibration, beeping and one half failing

When one half shakes and ignores tilting while the whole board beeps and flashes a red indicator, we check the gyro board, the link between the halves and the main board. In a common layout the controller sits in one half and a slave board in the other, joined by wires that run through the central axle, and sharp turns and falls chafe these wires. Our hoverboard repair technician tests the link between the boards, inspects the connector soldering and finds out which side reports the error. We also check the gyro board plugs separately: vibration works them out of their sockets, so the signal drops only on bumps. From the beep pattern and the number of flashes our specialists narrow the search quickly, although every manufacturer codes its signals differently. Before replacing a gyro board, always check the wire through the axle: a break there gives the same signs but is easier to fix and needs no new electronics.

A wheel spins by itself or the board won't move

  • Dirt under the pad: dust and sand under the rubber footpad block the optocoupler, the board decides someone is standing on it, and the wheel starts spinning by itself.
  • Stuck rubber: a deformed pad does not spring back, keeps the sensor pressed and stops the board from entering standby after the rider steps off.
  • Faulty optocoupler: if the sensor cannot see the foot, that half does not engage in balancing, and the platform beeps when the rider tries to step on.
  • Broken sensor wire: an impact pulls the thin wires to the footpad sensor out of the connector, and the signal drops right while riding.
  • First check: remove the pad and gently blow the sensor out with compressed air; it is safe and sometimes restores a normal response without any repair.

Battery, protection board and charger

The battery is the most expensive and most dangerous unit of the board. We explain how to tell a battery failure from a charger fault, when the protection board trips and which signs mean you must not ride the board at all.

Won't charge, battery or charger

If the charger indicator does not change color and the board will not turn on, we first measure the voltage at the charger output and at the battery connector, which immediately separates a charger fault from a battery failure. A working charger delivers a voltage slightly above the battery rating printed on its label; if the output is dead, the charger is to blame and the battery does not need replacing. The charger is also tested under load: a faulty unit may show voltage with no load but drop it once the battery is connected. The third common cause is an oxidized or loose charging port on the shell: the contact heats up, melts the plastic and stops passing current. Free hoverboard diagnostics at Tech Service cover all three checks, and the technician explains the result before any work starts. Do not charge the board with someone else's charger of a different voltage: even a plug of the same shape does not guarantee the protection board will survive the experiment.

Fast drain and cutting out while riding

Fast drain and sudden shutdown under load point to weakened cells or a tripped BMS protection board. The battery is built from series-connected groups of 18650 lithium-ion cells, and if one group loses capacity, its voltage is the first to sag on a climb. The BMS sees the dip and cuts the power, so the board shuts off on a hill even though the indicator was just showing charge. Such a battery is dangerous on a descent, because a sudden shutdown underfoot ends in a fall. After long storage without top-ups the cells go into deep discharge, and the protection may stop passing current altogether, which looks like a completely dead battery. Replacing one group is possible, but it pays off only when the new cells are matched in capacity and internal resistance; otherwise the new and old cells keep unbalancing the pack and the range barely improves.

Signs of a dangerous battery

  • Swollen casing: a battery that has swollen and presses on the compartment cover can catch fire, so we advise stopping charging and riding at once.
  • Smell and heat: a sweetish chemical smell or a hot battery after a short ride indicate damaged cells inside the pack.
  • Traces of liquid: damp spots, white deposits and corrosion on the contacts mean electrolyte leakage or water getting into the battery compartment.
  • Charging in the cold: lithium-ion cells must not be charged while frozen, so after frost the board is first left to warm up to room temperature.
  • Our advice: do not open a swollen battery yourself; we handle damaged cells in our service center, not in the owner's apartment.

Shell, pivot axle and the effects of impacts

Falls, curbs and puddles hit the shell and everything hidden under it. Below is what breaks from impacts and water, how it shows and which damage the board can live with without serious work.

Cracked shell and creaking in the middle

We judge a crack in the plastic shell by its location: a cosmetic chip on the fender does not affect riding, while a crack at the platform mount or above the wheel means the cover has to be replaced. New covers are matched to the model and wheel size, because the mounts differ between series. The shell sits on the metal frame of two halves joined by a central pivot axle, and it is this axle that lets the halves tilt independently of each other. A hard impact can bend the axle and break the bushings around it, and then the board creaks, the halves wobble and the balance drifts even after calibration. When the board is open, our specialists check the frame, the axle and the retaining rings, along with the wires running through the middle. Do not tape over a crack above the wheel: water and sand get in through it, and the next fault will hit the board electronics rather than the plastic.

What to do after puddles and rain

If the board has gone through a puddle, switch it off at once and do not charge it until the inside dries: water on a live board shorts the traces and burns out the power transistors. Moisture gets in through the charging port, gaps in the shell and the seal around the button, and blow-drying from the outside barely reaches the board. Even if the dried board turns on, salt deposits stay on the contacts, slowly oxidize the solder and cause intermittent errors. That is why hoverboard repair after water means disassembly, washing the board, drying and checking the battery connectors, not just waiting. The battery compartment is inspected separately: water inside the cell pack is more dangerous than on the board because you cannot see it from outside. The sooner the shell is opened, the better the chance that cleaning is enough: oxidation progresses day by day, and after a couple of weeks the traces and contacts themselves need restoring.

What we inspect after a fall

DamageHow it showsWhat we check
Chipped shell fenderVisible defect, riding unaffectedCover mounting
Crack above the wheelWheel rubs the plasticShell and tire
Bent pivot axleCreaking, play between halvesAxle, bushings, frame
Torn wire in the middleOne half does not workWires and board connectors
Wheel hit against a curbHumming, wheel wobbleMotor axle, bearings
Hit on the undersideWill not turn on at allBattery and its mounting

Which riding and storage habits speed up breakdowns

Many faults come not from factory defects but from how the board is ridden and stored. We look at what speeds up wear, what the owner can do alone and where DIY attempts only do harm and make the future repair costlier.

Overload, curbs and climbs

The main enemy of hub motors and the board is overload: weight above the rated limit, long climbs and riding over curbs. On a steep climb the motors draw maximum current, the controller power transistors heat up, and with frequent repetition the solder around them cracks. Jumping off curbs hammers the motor axle and bearings, while hitting the edge of the pavement with the wheel crushes the tire and bends the rim. Riding on sand and gravel also hurts, as the abrasive grit packs into the bearings and under the footpads. The Almaty terrain, rising noticeably toward the mountains, adds load: long climbs heat the electronics, and on descents you have to brake by leaning all the time, so the motors work under current again. Look up the maximum load for your model in the manual and do not ride two at a time, with a child in your arms or with a heavy backpack: even a small excess turns every climb into a test for the board.

Storage and charging in the cold season

For winter we advise keeping the board in the apartment with the battery about half charged and checking the level from time to time: a lithium-ion battery left at zero keeps slowly losing charge and slides into deep discharge. After such storage the BMS protection board may not let the charger start, and the owner decides the battery is dead, although the cause can be the protection itself rather than the cells. A cold balcony or a car trunk does double harm: capacity drops temporarily in frost, and frozen cells must not be charged. Keep the charger warm and dry as well. Charging starts only after the board has rested indoors and warmed up to room temperature. Before the first spring ride, charge the battery fully and test the board on a short level stretch, so a weakened cell group shows itself before it cuts the power on the road.

What the owner can do alone

  • Safe to do yourself: wipe the shell, blow out the footpad sensors, check the pressure in tube tires and run calibration following the model's manual.
  • Better not to do yourself: open the battery, resolder connectors on the board or plug in a charger from other equipment with a similar plug.
  • Jumpers on the protection: bypassing the BMS with a wire for extra range removes short-circuit protection and makes the battery a fire hazard.
  • Firmware from the internet: third-party firmware may not suit the controller and leave the board without balancing, and restoring the factory version can be hard.
  • Honest account: if you are looking for where to fix a hoverboard after an unsuccessful DIY attempt, tell our technician what you changed; it shortens the search for the fault.

How hoverboard repair works with us

From the request to the final check of the board, everything follows one clear order. We explain what we do at your home, what in the service center, how we name the cost and how the warranty and payment work.

Visit, diagnostics and approving the work

With us everything starts with a request: a specialist arrives within 60 minutes anywhere in the city and runs free diagnostics on site, checking the battery and charger, testing the motors and sensors, and watching the footpad response and the balance of both halves. Based on the results, the technician explains the cause, names the cost and agrees on the scope of work with the owner. Hoverboard repair near you saves carrying a heavy board through traffic: replacing a tire, bearings or footpads and calibration are usually done on site, while soldering boards, work on battery cells and complex disassembly happen in the service center. Describe the model and symptoms (beeping, a flashing indicator, a wheel noise) when you book, so the specialist knows in advance which unit to check first. If the job needs the service center, the technician explains what will be done with the board and why.

What makes up the cost

We name the cost only after free diagnostics, because the same symptom on two boards can mean completely different work. Calibration and cleaning the footpad sensors cost noticeably less than replacing the main board or rebuilding the battery. When owners ask about hoverboard repair prices, the answer depends on three things: which unit has failed, how complex it is to take that model apart and which part is needed, whether a tire, bearing, gyro board, connector or cell group. If there are several causes, they are listed separately so the owner can decide what to fix right away. Sometimes the work stops making sense: if a budget model has lost both the battery and the controller at once, the specialist will say plainly that replacing them costs about as much as a new board. Before booking, find the model name and wheel size on the sticker under the board, since this data makes it easier to see in advance which parts will fit.

Warranty, payment and a direct contractor

For completed repairs we give a 1-year warranty on labor and parts and you can pay via Kaspi QR, Kaspi Red, bank card, cash or bank transfer for companies. Tech Service is a direct contractor: the board is fixed by our own technician, not by an outside subcontractor the order was passed to, and it never goes to third parties, so the same service whose specialist did the work answers for the result. Our technicians have 4 to 20 years of experience, gained on many models, boards and batteries. When the repair is finished, the board is tested in operation: power-on, balance on both halves, footpad response, braking by leaning and battery charge. Check the board together with the specialist while they are still there: step on, ride a few meters and turn on the spot, because a remark made right away is resolved fastest.

Hoverboard repair tips for safe riding

A hoverboard breaks down predictably: each symptom has its own unit and its own first check. Below are the main takeaways on wheels, balance, battery and everyday use.

  • Wheel sound: humming and play point to the bearings, while jerks and twitching on start point to the Hall sensors and motor phase wires.
  • Balance: drifting to one side is first fixed with calibration, and if that fails, the gyro boards, the wire through the axle and the frame are checked.
  • Footpads: a wheel that spins by itself usually signals dirt or a faulty optocoupler under the platform's rubber pad.
  • Battery: swelling, smell and heat require stopping charging at once, and a frozen board goes on charge only after warming up.
  • Water and impacts: after a puddle the board is switched off and opened as early as possible, before oxidation reaches the board traces.

8brands

Which hoverboard brands we repair in Almaty

Choose a brand on the site to open the page describing the work and models.

We also repairWe also repairTECH SERVICE09

Besides hoverboard repair, we fix other equipment in Almaty

Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.

BlogBlogTECH SERVICE10

Worth reading before hoverboard repair in Almaty

Leave a review

Choose a platform — the TECH SERVICE page will open.

2ГИС2GISGoogle MapsЯYandex Maps
Send a review with photos on WhatsApp