Original
Compressor for your refrigerator model
- Selection
- by model and part number from the nameplate
- Compatibility
- fully matches the original unit
- Delivery time
- depends on supplier availability
- Warranty
- 1-year warranty on labor and parts
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 746 00 26Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician will arrive within 60 minutes anywhere in the city, check the circuit, and recharge your fridge with the correct refrigerant. Diagnostics are free.
Our own technicians4 to 20 years of experience




60 minutestechnician arrival anywhere in the city
Freediagnostics are free
1 yearwarranty on labor and parts
A recharge is more than just adding gas. First, the technician finds and fixes the leak, vacuums the circuit, and only then fills the refrigerant by weight. After that, they check how well the fridge cools. Diagnostics are free, and the technician quotes the price after them.
01
Step 1inspection
The technician inspects the tubes and connections, checks the circuit with a leak detector or soap solution, and if needed, pressure-tests with nitrogen.
02
Step 2sealing
The found spot is soldered or the damaged section of the circuit is replaced so the refrigerant doesn't leak again after the recharge.
03
Step 3vacuum
Air and moisture are pumped out of the circuit with a vacuum pump. Without this step, moisture remains in the system and the fridge won't reach the proper mode.
04
Step 4recharge
The technician fills the refrigerant specified on the fridge's nameplate and measures the dose by weight, not by eye.
05
Step 5check
After the recharge, the technician checks the circuit pressure, the temperature in the compartments, and how the compressor reaches operating mode.
5
Refrigerant isn't consumed during normal operation: if it's gone, there's a leak. The owner can notice the five signs below even before calling a technician.
Temperature difference between compartments
When refrigerant is low, the freezer may not freeze as well, while the main compartment stays warm—the temperature difference between compartments changes.
Compressor doesn't turn off
The motor hums continuously and doesn't shut off: it's trying to reach the temperature, but there isn't enough refrigerant in the system to cool.
Frost on the evaporator
A layer of snow appears on the back wall or evaporator, or, conversely, some areas have no frost—the circuit cools unevenly.
Oil on the tubes
Oily spots appear at connections and on visible tubes at the back. Refrigerant escapes together with oil, so the trace reveals the leak location.
Condensation and moisture
Condensation collects on the tubes or near the back wall where there wasn't any before. This is also a reason to check the circuit's tightness.
If you notice at least one sign, move perishable food to another fridge or a thermal bag before the technician arrives.
Describe the symptomsThe compressor is selected based on the refrigerator model and the part number on the nameplate.
Original
or
Analog
The table shows the cost of refilling refrigerant in a refrigerator: a "from" price for the work without parts and the time it takes; the technician confirms the final amount before starting the repair.
1–2 hourstime
from 12,000 ₸cost

BeforeAfterThe home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsField refrigerator repair technician
experience12 yearsGeneral household appliance repair technician
experience8 yearsExpert washing machine repair technician
We reply during working hours
Leave a request and a technician will arrive within 60 minutes anywhere in the city. We provide a 1-year warranty on labor and parts.

Warranty question? Call us
+7 (778) 746 00 267 898 reviews of repairs at TECH SERVICE in total
Асель Ж.Order No. 2026-4630 · 5 February 2026
oursДолго искал, кому это отдать, и вот нашёл. Повод для визита: намерзает лёд. Никита М объяснил причину так, что понял даже я. Сказали 32 500, я согласился без торга. Диагностику сделали бесплатно, хотя я был готов платить. В списке работ — уплотнитель. Рекомендую. Проверили при мне, показали, что всё держит
Алексей Г.Order No. TS-2501-114 · 4 August 2025
oursРаботаю допоздна, поэтому нужен был сервис с нормальным графиком. По деньгам вышло адекватно, в другом месте просили больше. Уже полгода — ни одного сбоя)
Мадина Т.Order No. TS-7219 · 28 November 2024
oursХотел сначала вызвать мастера на дом, потом передумал. Нужен был ремонт холодильника — обратился сюда. С чем пришёл: шумит. Сказали 27 000, а потом ещё и скидку сделали. Приехал вечером, мастер ещё был на месте. Заодно поменяли: термостат. В помещении тесновато, но это мелочи. Внешне как новый, если не считать мелкой царапины!!
Индира П.Order No. ZK-1617 · 20 September 2024
oursХотел сначала вызвать мастера на дом, потом передумал. Техсервис на Абая, если не ошибаюсь, — вот туда и поехал. Проверили на всех режимах, всё чётко!!
Лилия В.Order No. TS-4770 · 30 May 2024
oursРаботаю допоздна, поэтому нужен был сервис с нормальным графиком. Основная жалоба — намерзает лёд. Проверили при мне, показали, что всё держит.
Светлана Д.Order No. ZK-2019/136 · 30 May 2019
oursБыло подозрение, что дело в плате, хотелось услышать второе мнение. Честно, уже готовился покупать новое, но обошлось. Проблема — шумит. Проверил дома — всё на месте, ничего не забыли.
Аяна Е.Order No. 25364 · 9 December 2017
oursОтдал мастеру: холодильник. Жалоба простая: шумит. Никита М объяснил причину так, что понял даже я. Смета совпала с итогом, что редкость. Поставили новую деталь: термостат. Мастер сразу сказал, что к чему, без размытых формулировок. Нагрев в норме, посторонних звуков нет.
Станислав К.Order No. TS-3337 · 28 February 2017
oursПовод для визита: шумит. Дильмурат С всё объяснил и не пытался впарить лишнее. Уже полгода — ни одного сбоя.
Сергей Р.Order No. ZK-8150 · 20 March 2016
oursХотел сначала вызвать мастера на дом, потом передумал. Нужен был ремонт холодильника — обратился сюда. Основная жалоба — шумит. Всё оформили по договору, с печатью. Заодно поменяли: термостат. Вышло 34 500 тенге, дешевле, чем я рассчитывал. Однозначно да. Проверил дома — всё на месте, ничего не забыли.
Евгений М.Order No. TS-5582 · 15 February 2016
oursДолго откладывал ремонт, потом всё-таки собрался. Привёз на диагностику: холодильник. С чем пришёл: намерзает лёд. Ни копейки сверху, как и обещали. Разобрали, посмотрели: уплотнитель. Приняли без очереди, оформили за пять минут. Хороший сервис, побольше бы таких. Крутит ровно, без рывков
Didn’t find the answer? Message us on WhatsApp.
Ask a questionThe main signs are the fridge no longer cooling, the compressor running nonstop or staying silent, frost on the evaporator, and oil on the pipes. A technician makes an accurate diagnosis after a free on-site inspection.
The compressor hums but there's no cold: the compartments stay warm, and the freezer may cool slightly or not work at all. The condenser stays cold, and the compressor often doesn't shut off as it tries to reach the set temperature.
Refrigerant is filled for the entire service life of the refrigerator and isn't consumed like fuel. If it's gone, the circuit has lost its seal, and recharging without finding and fixing the leak won't help.
Yes, a technician comes with everything needed and recharges the refrigerator right in your kitchen. A city visit takes about 60 minutes, and the inspection before work is free.
Because the cause wasn't fixed: the refrigerant leaks again through the same damage. First the technician finds the leak, solders the circuit, and checks for tightness, and only then recharges.
R600a is isobutane, which is flammable, so the technician works with an open flame and fills strictly according to the rules. Under normal use and proper recharging, it's safe for people in the apartment.
Tech Service provides refrigerator refrigerant recharge in Almaty with a technician visiting your home. We start with free diagnostics, then locate the leak, seal it, evacuate the system, and recharge to the factory specification. We offer a 1-year warranty on labor and parts, and the technician arrives within 60 minutes anywhere in the city.
Refrigerant in a working refrigerator isn't consumed; it only escapes through a leak in the circuit. So "not cooling" is a symptom with several possible causes, and it's important not to confuse a leak with a faulty start relay, thermostat, or fan.
A typical sign of a leak is a warm fridge compartment while the freezer still works and the compressor runs nonstop without cooling. Refrigerant escapes gradually, so the lower compartment loses temperature first while the freezer still manages. As more gas is lost, the difference grows: food in the fridge spoils within a day or two, condensation disappears from the walls, and the evaporator gets patchy frost or stays dry. The motor runs continuously trying to reach the set temperature, and its body heats up less than usual. A oily wet streak near the rear grille or on the tubes by the compressor should also raise suspicion—that's the oil trace escaping with the gas. If the compressor body stays cold instead of hot, it more often indicates refrigerant loss rather than motor wear. If a leak is confirmed, a refrigerant recharge is needed—in Almaty we perform it after locating and fixing the leak.
During free diagnostics, we check the start relay, thermostat, and No Frost fan before concluding there's a leak. The start relay often fails on appliances older than seven or eight years: the motor clicks, tries to start, and stalls while the compartments stay warm. A thermostat or temperature sensor gives the opposite picture—the unit either doesn't turn on at all or runs nonstop, and food in the fridge compartment freezes. A No Frost fan stops circulating cold air through the ducts: the freezer stays cold while the upper compartment warms up. Another marker is ice and a snowdrift only on the back wall of the freezer while the lower compartment is warm. The start relay and fan produce a similar "not cooling" symptom, but with them the compressor usually doesn't run continuously, and the compartment cools unevenly.
Topping up without fixing the cause of the leak gives only a temporary effect—after a few months the refrigerant escapes again, and the refrigerator stops cooling. Here's why that happens and how we seal the problem for good.
We don't do top-ups until we've found and fixed the leak, because refrigerant isn't consumed during operation—it escapes through a hole in the circuit. Gas circulates in a closed refrigeration loop for years: if the volume drops, there's a hole somewhere—in the foamed part of the body, at a tube joint, or in the evaporator. The technician locates the hole by oil traces, with a leak detector, or by nitrogen pressure testing, opens the section, and solders it. Without soldering the circuit, a new charge will simply escape through the same gap—sometimes within weeks. In my view, topping up "by eye" without finding the leak is a delay, not a repair. If the hole isn't soldered, the fresh refrigerant will escape the same way, and a repeat visit will cost more than fixing the cause right away. The price for refrigerator refrigerant recharge in Almaty depends on the circuit volume and refrigerant type, and the technician quotes it after free diagnostics.
The work is done at the client's home: the technician arrives with their own equipment, runs diagnostics, fixes the leak, and charges refrigerant to the factory specification.
| Step | What the technician does | What they check |
|---|---|---|
| Diagnostics | Inspects the fridge, listens to the compressor | Relay, thermostat, fan |
| Leak detection | Checks the circuit with a leak detector | Leak location |
| Sealing | Brazes the circuit, replaces the filter-drier | Seal after brazing |
| Evacuation | Pumps out air and moisture from the system | Readiness for charging |
| Charging | Fills refrigerant to factory specification | Weight and type of refrigerant |
| Check | Starts the fridge and monitors cooling | Operation of compartments after charging |
The technician arrives within 60 minutes anywhere in the city, and the procedure itself with brazing and evacuation takes several hours; the technician will give a more precise estimate after diagnostics. We provide free diagnostics, so the time spent finding the leak and assessing the circuit adds no cost. The specialist quotes the price after inspection, once the scope of work and refrigerant type are clear. If you want to know in advance how much charging the fridge with refrigerant will cost, the price depends on the refrigerant type and scope of work, and the exact amount is given by the technician after free diagnostics. While you wait, avoid opening the doors unnecessarily and move perishable food to a thermal bag — it will stay cold longer. Our experience shows that a fully loaded compartment speeds up cold loss, so it's better to remove some food beforehand. If you have meat or berries in the freezer, pack them tightly in one compartment and don't touch them until the technician arrives — cold will last longer.
The refrigerant type is determined by the fridge model, and it affects both service quality and safety measures during work in the apartment.
We work with R600a and R134a refrigerants, and determine the required type from the factory nameplate of the specific model. R600a is isobutane, used in most modern household fridges: it removes heat more efficiently with a smaller volume but is flammable. R134a is a non-flammable refrigerant used in older equipment and some No Frost models. The circuit pressure and fill rate differ for these gases, so the technician checks the marking on the compressor and the device passport before connecting the cylinder. The technician quotes the cost of charging the fridge with refrigerant after free diagnostics — the final price depends on the refrigerant type and scope of work. You can't just fill any refrigerant: different refrigerants have different pressure and fill rates, and a mistake will damage the compressor. In my opinion, it's easier to find the nameplate once than to replace the motor later.
R600a (isobutane) is flammable, so working with it requires care in an apartment, and tampering with a cylinder without the right equipment and skills is risky. R134a itself does not burn, but it displaces oxygen in a confined space and can cause suffocation at high concentrations. Neither gas has an odor in its pure form, and no odorant is added to cylinders — you won't be able to smell a leak. Isobutane is heavier than air and accumulates near the floor, so if you smell gas indoors, do not turn on any appliances and ventilate the room. A refrigerant cylinder under pressure requires a manifold gauge and scales — you can't measure the norm by eye. Liquefied gas in such containers should be stored away from heating devices and not left in a car in the sun.
Filling the circuit is completed by checking the refrigerator in operation, and the work performed and replaced parts are covered by a warranty. Calling a technician in the city follows clear terms — from request to follow-up visit.
We provide a 1-year warranty on labor and parts, and refilling after a leak is fixed remains a one-time procedure. After filling the circuit, the technician turns on the unit and checks how it cools: listens to the compressor, checks the temperature in the compartments, and makes sure there is no frost on the pipes where it shouldn't be. Our technicians have 4 to 20 years of experience with appliances, so by how the unit behaves on the first cycle they can tell whether the circuit holds pressure. The warranty year covers brazing, the refrigerant itself, and replaced parts. If the refrigerator stops cooling again within the warranty period after service, we come back and find out why.
We've gathered the key facts about refilling refrigerant in a refrigerator in one place — so you can decide based on the condition of the appliance, not just symptoms.
If you ask, the technician will check other parts during the same visit.
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
If your refrigerator stops working, first check the outlet, the power cord, and the thermostat setting, and after defrosting let it stand for a while.
4 February 2026 · 12 minutes read
If your refrigerator isn't cooling but the light is on, the cause is usually one of the components in the cooling circuit: the compressor, thermostat…
10 December 2025 · 13 minutes read
If your dishwasher won't drain, the most common culprits are a clogged filter or drain hose; less often, it's the pump, impeller…
24 March 2026 · 12 minutes read
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
If your microwave isn't heating but the light and turntable still work, the problem is usually one of the high-voltage components — the magnetron, diode…
15 February 2026 · 12 minutes read