Open until 19:00+7 (778) 021 13 16Call a technician
Tech Service technician next to a juicer

Juicer Repair in Almaty

A technician arrives within 60 minutes anywhere in the city. Diagnostics are free.

  • 1-year warranty on labor and parts
  • Arrival in 60 minutes anywhere in the city
  • Diagnostics free of charge

Our own technicians4 to 20 years of experience

Ruslan Ts.Damir M.Dilmurat S.Dima

Repair prices

  • Diagnostics0 ₸
  • Bearing replacementfrom3 000 ₸
  • Motor replacementfrom4 000 ₸
  • Power circuit repairfrom4 500 ₸
  • Leak repair (seal replacement)from5 500 ₸
All prices
2ГИСЯours4,97 898 reviews
2GIS · Google · Yandex · order database
Common faultsCommon faultsTECH SERVICE02

Common juicer faults in Almaty

The technician names the cause after free diagnostics.

PricesPricesTECH SERVICE03

How much juicer repair costs in Almaty

The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.

Bearing replacementparts not included

1–2 days

from3 000 ₸

Motor replacementparts not included

1–2 days

from4 000 ₸

Power circuit repairexact price — after the free diagnostics

1–3 hours

from4 500 ₸

Leak repair (seal replacement)parts not included

1–3 hours

from5 500 ₸

Motor brush replacementparts not included

1–2 days

from6 000 ₸

Before and afterBefore and afterTECH SERVICE04

Before and after juicer repair in Almaty

Lid does not lock, motor does not start

1–2 hourstime

from 6 000 ₸cost

Problem
The juicer's lid stopped locking, and the motor would not start.
What we did
The technician removed the locking arc, replaced the cracked axle and the arc itself, then checked that the motor turns on only when the lid is closed.
Result
The lid locks securely again, the juicer works, 1-year warranty on labor and parts.
I want the same
On the workshop bench stands a juicer with a transparent bowl; the technician places a new locking arc onto the axle on the side of the housing and inserts a pin, and the old arc lies nearby on the mat.BeforeAfter
01 / 03
All repairs
TECH SERVICE mobile technician with a tool case

How juicer repair works at your home in Almaty

From request to final check, with free diagnostics.

  1. Requestby phone

    Describe the model and the symptom so the technician can understand the fault more easily.

  2. Technician visitin 60 minutes

    The technician arrives within 60 minutes anywhere in the city.

  3. Diagnosticsfree

    Diagnostics are free and done before any work is agreed.

  4. Approvalafter review

    You approve the scope of work and the list of parts to be replaced.

  5. Checkafter repair

    The technician checks how the juicer works. 1-year warranty on labor and parts.

Leave a request
TechniciansTechniciansTECH SERVICE05

Our home appliance repair technicians in Almaty

The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

  • 8 technicians in Almaty
  • 8–12 years of experience in the department
  • Article author Ruslan Ts., 9 years of experience
Mobile technician fixing a washing machine at the customer's home
Field technician at a customer’s home

The department has 8 specializations — they are listed on the technicians' cards.

01 / 08
Ruslan Ts., washing machine and refrigerator repair technicianexperience9 years

Ruslan Ts.

Washing machine and refrigerator repair technician

Damir M., general household appliance repair technicianexperience12 years

Damir M.

General household appliance repair technician

Dilmurat S., field technician for washing machine and refrigerator repairexperience10 years

Dilmurat S.

Field technician for washing machine and refrigerator repair

Dima, expert washing machine repair technicianexperience8 years

Dima

Expert washing machine repair technician

Nikita M., field refrigerator repair technicianexperience8 years

Nikita M.

Field refrigerator repair technician

Oraz, senior washing machine repair technicianexperience8 years

Oraz

Senior washing machine repair technician

Radik T., dishwasher repair technicianexperience11 years

Radik T.

Dishwasher repair technician

Rustem T., washing machine repair technicianexperience9 years

Rustem T.

Washing machine repair technician

We reply during working hours

Book juicer repair in Almaty

You can leave a request by phone or through the form on the website. A technician will arrive within 60 minutes and run free diagnostics.

TECH SERVICE administrator replying to a customer's WhatsApp message

Warranty question? Call us

+7 (778) 021 13 16
Customer reviewsReviewsTECH SERVICE06

Reviews of juicer repair in Almaty

Жанна О.Order No. ZK-7729 · 25 January 2025

ours

Смотрел, у кого есть запчасти на такую модель. Честно, уже готовился покупать новое, но обошлось. Повод для визита: течёт. Деталь на замену — двигатель. Сказать, что доволен — ничего не сказать

Repair: juicer repair in

Азамат Е.Order No. ZK-1265 · 14 December 2024

ours

Смотрел, у кого есть запчасти на такую модель. Уже не верил, что это можно починить. Повод для визита: течёт. Могли бы взять больше, но взяли по-божески. Вернули в тот же день, всё функционирует

Repair: juicer repair in

Нурасыл М.Order No. ZK-4936 · 25 October 2024

ours

Работаю допоздна, поэтому нужен был сервис с нормальным графиком. Сначала сомневался, мало ли что. Проблема — вибрирует. Работает как раньше, придирок нет.

Repair: juicer repair in

Руслан Д.Order No. ZK-1790 · 16 August 2024

ours

Пробовал найти мастера в своём районе, но все были заняты. Основная жалоба — вибрирует. Про тех сервис слышал от коллеги, теперь проверил сам. Проверили на всех режимах, всё чётко.

Repair: juicer repair in

Айгерим Б.Order No. 951544 · 25 March 2024

ours

Позвонил знакомому, он раньше работал в сервисе, посоветовал этих. Запчасть была в наличии, доплачивать не пришлось. С тех пор ни разу не подвёл.

Repair: juicer repair in

Алия Ш.Order No. ZK-2023/684 · 4 July 2023

ours

Работаю допоздна, поэтому нужен был сервис с нормальным графиком. Утром столкнулся с тем, что течёт. Ни копейки сверху, как и обещали. Приняли, выдали квитанцию, всё по-человечески. Разобрали, посмотрели: двигатель. Пришлось самому напоминать про гарантийный талон. Не пожалел ни разу. Сделали и забыл про проблему.

Repair: juicer repair in

Наталья С.Order No. ZK-6447 · 11 February 2023

ours

Поломка застала перед командировкой, тянуть было нельзя. Жалоба простая: не крутит. Починили и дали гарантию на месяц)

Repair: juicer repair in

Роман З.Order No. 377950 · 24 January 2023

ours

Выбирал по отзывам в 2ГИС, времени на эксперименты не было. Повод для визита: вибрирует. Проверили при мне, показали, что всё держит.

Repair: juicer repair in

Дмитрий Л.Order No. TS-8112 · 29 April 2022

ours

Работаю допоздна, поэтому нужен был сервис с нормальным графиком. Техника работала годами, а тут — течёт. Радик Т не стал навязывать дорогую запчасть, поставил нормальную. Сделали аккуратно, следов разборки не видно

Repair: juicer repair in

Ержан А.Order No. ZK-1462 · 25 September 2021

ours

Хотел сначала вызвать мастера на дом, потом передумал. Поломка застала врасплох: течёт. По деньгам вышло адекватно, в другом месте просили больше. Поставили новую деталь: фильтр. Позвонили заранее, предупредили, что задержится на полчаса. Проверил дома — всё на месте, ничего не забыли.

Repair: juicer repair in
Questions and answersQuestionsTECH SERVICE07

Questions about juicer repair in Almaty

Didn’t find the answer? Message us on WhatsApp.

Ask a question
Do you repair Kitfort juicers when they stop turning on with the lid closed?

Yes, we repair these models. Most often the lid microswitch or limit switch is at fault: the board doesn't get the signal that the safety guard is closed and won't start the motor. A technician will check the interlock circuit and replace the faulty part.

Can I replace the lid microswitch on a juicer myself?

Technically yes, if you find the right part and carefully take the housing apart, but it's easy to damage the plastic or mix up the contacts. Without experience, it's better to leave it to a technician: they'll match the limit switch to your model and make sure the safety guard works properly.

Can the sieve on a centrifugal juicer be replaced separately?

Yes, the sieve and its holder are replaced as a separate unit if the mesh is torn or deformed. It depends on the model: for some juicers the part is easier to find, for others harder. The technician will tell you after inspecting your appliance.

How can I tell if the gearbox on a masticating juicer is worn out?

Signs include crunching or clicking during juicing, the auger turning in jerks, and stopping under load even though the motor hums. This points to worn plastic gears in the gearbox, and the unit needs to be taken apart and replaced.

Why is it dangerous to keep using a juicer that gets hot and smells like burning?

That smell usually means the motor is overheating or the insulation is melting, and it can lead to a short circuit. Don't use the appliance while this is happening: unplug it and take it in for diagnostics so you don't burn out the motor completely.

What should I do if the same problem comes back after juicer repair in Almaty?

Call us and describe what's happening: there's a 1-year warranty on labor and parts. A technician will inspect the appliance again and figure out why the problem returned.

Repair guideArticleTECH SERVICE08

Juicer repair in Almaty by Tech Service technicians

Ruslan Ts., washing machine and refrigerator repair technician

Author: Ruslan Ts.,Washing machine and refrigerator repair technician

Published
Updated

Juicer repair in Almaty is done by Tech Service's own technicians: a specialist comes to your home within 60 minutes, and complex faults are fixed at our service center. Diagnostics are free, technicians with 4 to 20 years of experience handle centrifugal, slow and citrus models, and we give a 1-year warranty on labor and parts.

What broke if your juicer hums, leaks or will not turn on

Every complaint points to a specific culprit part. That is why the technician knows from the symptom alone which part to check first and does not take the housing apart blindly.

The juicer will not turn on after assembly

When the appliance ignores the button, we first check not the motor but the chain in front of it: the plug, the power cord, the button and the lid lock. Almost all juicers refuse to start until the locking clamp presses the lid and the tab on it pushes the microswitch. If the tab has broken off or the clamp has loosened, the contact does not close and the unit looks completely dead, even though the motor is fine. The second cause is a tripped thermal fuse: it opens the circuit after overheating and on some models does not reset by itself. A cord frayed at the base gives a similar picture, only intermittent, with the unit switching on and cutting out as the cable moves. Before deciding the winding has burned out, reassemble the juicer strictly by the marks on the housing, because a lid that is not seated properly blocks the start just like a broken sensor.

The motor hums, but the auger or disc does not move

Among requests for juicer repair in Almaty, we link humming without rotation primarily to the drive, not to the motor winding. Between the motor shaft and the working part sits a plastic coupling: when something jams, it shears first and so protects the motor from overload. In slow juicers the same result comes from a broken gear tooth in the gearbox, and in induction motors from a start capacitor that has lost capacitance, without which the rotor will not move. A simple sign helps tell these faults apart: if the shaft turns freely by hand with the bowl removed and you hear crunching, the coupling or a gear is to blame; if it turns stiffly, it is a bearing or a stuck piece of produce. Do not keep switching on a humming unit, as a stalled rotor quickly overheats the winding, and a minor drive fault turns into a motor replacement.

Symptom and likely part

SymptomLikely partWhat the technician checks
Leaks under the baseShaft seal, bowl gasketsSeal fit, juice traces near the motor
Strong vibrationStrainer, shaft bearingsStrainer balance, shaft play
Pulp in the juiceTorn mesh, worn augerMesh integrity, auger edge
Burning smellBrushes, motor windingBrush length, commutator condition
Shuts off while runningThermal fuseHousing temperature, protection circuit
Grinding while juicingGearbox gearsGear teeth, lubrication

How centrifugal, slow and citrus models are built

The design determines which part wears out first. Centrifugal, slow and citrus juicers extract juice differently, so each has its own weak spots, and we go through them by type.

Centrifugal model with a grating disc and strainer

A centrifugal model shreds produce with a grating disc and separates the juice with a strainer that spins at the high speed of a brushed motor. That speed makes the design sensitive to balance: pulp stuck on one side, a bent mesh or a crack in the plastic basket immediately cause wobble, and the unit starts creeping across the counter. Vibration loads the shaft bearings, so an ignored imbalance eventually turns into play and noise. The second wear part is the carbon brushes of the brushed motor: they wear down gradually, and near the end of their life you get sparking, a burning smell and lower speed. The grating disc goes dull from pits and hard root vegetables, which makes juicing jerky. If vibration appeared right after washing, check that the strainer is fully clicked in, because a crooked mesh shakes the unit as hard as a broken one.

Slow juicer with a gearbox

In slow juicers we most often work with three parts: the gearbox, the auger itself and the shaft seal. The slow auger presses produce with great force, and that force is transmitted by a gearbox with a set of gears, so overloading with dense root vegetables or large chunks wears and shears the teeth. Over time the plastic auger develops cracks, especially at the base where it sits on the shaft; a cracked part juices worse and can jam in the drum. The seal under the bowl keeps juice from running down to the motor, and when the rubber hardens, a sticky drip appears under the base. We advise not to put off dealing with such a drip: sugary juice that reaches the bearings and winding turns a seal replacement into a motor repair. We check the gears together with the shaft, otherwise a new part will soon share the fate of the old one.

Citrus presses and food processor attachments

  • Citrus press with reverse: the cone changes direction with every press, so the reverse switch and the plastic drive teeth wear out.
  • Lever press: the lever pushes down on half a fruit, over time the hinge breaks and the spring weakens, and the motor overheats from long operation.
  • Food processor attachment: it has no motor of its own, so the fault is checked in two places at once, the attachment socket and the base drive.
  • Combination model: the auger and the citrus cone run on a shared motor, and when one attachment breaks, the other often stays fully working.

What the technician checks during free diagnostics

Diagnostics follow the chain from the socket to the auger. Only after that is it clear which part to replace and whether the repair makes sense, so the technician does not name the cause remotely.

Electrics from plug to motor

  • Plug and cord: the technician tests the cable along its whole length and bends it separately at the base, where the wires fray first.
  • Button and speed switch: the contacts are checked at every setting, since a burnt contact makes one of the speeds drop out.
  • Lid lock: the microswitch is checked on the assembled appliance, otherwise it is easy to miss a broken lid tab or a loose clamp.
  • Thermal fuse: a tripped fuse leaves the circuit open, and before replacing it the technician finds out what overheated the motor.
  • Motor: winding resistance is measured and the brushes and commutator are inspected, which tells a burnt motor from merely worn brushes.

Drive mechanics and seals

We check the mechanics in two steps: first we turn the shaft by hand with the bowl removed, then we run the appliance with produce and listen to it under load. The manual check reveals shaft play, a stiff bearing and coupling slip that is invisible at idle. Under load, worn gear teeth show up: the gearbox starts to crackle and the auger stalls on dense vegetables. We separately inspect the seal and the bowl O-rings, since darkened rubber that has lost its elasticity will let juice through even if the base is dry right now. Our technicians, with 4 to 20 years of experience, can tell gear wear from a dry bearing by the sound under load before opening the housing. Take shaft play seriously, as it appears before a leak and signals that the seal will soon stop holding juice.

How we quote the cost and agree on the work

We name the price of the work once the cause is found during the free check, and we start the repair only with the customer's consent. An honest quote over the phone is impossible: humming without rotation can be a sheared coupling or a burnt motor, and that is a completely different scope of work. Three things affect the total: which part has failed, how deeply the housing has to be taken apart and whether the appliance can be fixed on the spot. The technician shows the worn part and explains why it needs replacing, and if the repair is not worth it, says so directly. You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies, so you choose how to pay. Before the visit, copy the model name from the sticker on the bottom, which lets the technician understand in advance how your particular unit is built.

Juicer repair at home and at the service center

The format depends on the fault. The technician replaces a cord, button or strainer in the customer's kitchen, while the gearbox and motor need a full teardown and testing at several speeds.

What the technician does right in your kitchen

The technician arrives within 60 minutes anywhere in the city, and we do most minor jobs right in the kitchen. On site it is possible to replace the power cord and plug, the button and speed switch, the lid lock microswitch, the thermal fuse, as well as the strainer, the drive coupling and the bowl O-rings. These jobs do not need a deep teardown, since the parts become accessible after removing the bottom cover or the bowl. First the technician runs free diagnostics so as not to touch a working part, and after fitting the new part runs the appliance with produce and checks juicing under load. Carbon brushes can also be replaced at home if the housing is held by screws rather than hidden latches. A free table near a socket and good light are enough for a home repair, as small connectors and catches are easier to see.

When we repair the juicer at the service center

We move a complex juicer repair in Almaty to the service center when a full teardown is needed: replacing gearbox gears, replacing or rewinding the motor, restoring a housing with hidden latches. After assembly such parts must be run under load at different speeds and with different produce, which is awkward in a kitchen and takes a lot of the owner's time. In slow juicers the gearbox sits deep in the base and comes out together with the motor, so its repair almost always takes place at the service center. Centrifugal units end up there less often, mainly with a burnt winding or a broken shaft bearing. The technician decides on the format after on-site diagnostics, not over the phone, because the same-sounding hum can mean a minor or a serious fault. If a leak has already reached the motor, do not switch the appliance on before the technician's visit, so moisture does not damage the winding.

How to prepare the appliance for the technician's visit

  • Wash the removable parts: dried pulp on the strainer and auger gets in the way of inspection and hides the cracks the technician looks for first.
  • Gather all the parts: the bowl, auger, strainer, lid and pusher are needed on site, since the lock is checked only on an assembled unit.
  • Find the model sticker: it is usually on the bottom of the base, and the model name makes it easier to understand the design of that unit.
  • Recall the moment it broke: what you were juicing, whether there was crunching, a burning smell or a drip, as such a description shortens the path to the cause.

Which parts we replace and what the warranty covers

Below are the parts that wear out in juicers before the rest, and how the warranty works for their replacement and for the repair itself. We start with the replaceable parts.

Parts we replace most often

PartSign of wearWhat we do
Shaft sealSticky drip under the baseReplace the seal, clean the shaft
Drive couplingHum without rotationFit a new coupling
Gearbox gearsCrackling, auger stallsReplace gears, check the shaft
StrainerPulp in the juice, wobbleReplace the mesh, check balance
Carbon brushesSparking, loss of speedReplace brushes, clean the commutator
Lid microswitchNo start after assemblyReplace the switch or the catch
AugerCrack at the baseFit a new auger

1-year warranty on labor and parts

We give a 1-year warranty on labor and parts, covering the work done and the parts installed, which means both possible sources of a repeat fault at once. The technician's work means correct seating of the seal, tightening the housing screws and routing wires away from moving parts; the part is the coupling, gear or strainer itself. Over a year of regular juicing, a hidden assembly or part defect has time to show up, so this period gives the customer a real test of the repair quality. Once the appliance is back, use it as usual rather than keeping it on a shelf, because normal load will show faster whether everything is fine. Remember which part was replaced, as that makes it easier to describe the situation if you get in touch. If a new sound or a drip appears after the repair, do not wait for it to get worse, and let the technician know right away.

Our own technicians, no middlemen

At Tech Service juicers are repaired by our own technicians with 4 to 20 years of experience: we do not pass requests to outside contractors and do not work as a platform for finding freelancers. Our technicians know centrifugal, slow and citrus models from Hurom, Kitfort, Philips, Bork, Braun, Moulinex and Kenwood, so a specialist understands the design of a given brand before opening it, including where the latches are hidden, how the gearbox comes out and which screws must not be overtightened. Working directly removes the extra link between the customer and the contractor: one service handles diagnostics, repair and warranty, and nobody has to retell the fault. You can pay in a convenient way, as we accept Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies. When choosing a contractor, ask who exactly will come, a staff technician of the service or a freelancer found through a middleman.

Mistakes that make a juicer break again

Repeat breakdowns are often linked to habits rather than to part quality. A few simple rules extend the life of the motor, gearbox and strainer after a repair.

Overloading the motor and gearbox

  • Whole hard vegetables: carrots, beets and ginger root are cut into sticks, otherwise the auger jams and the gearbox gears take a shock load.
  • Running without breaks: long continuous juicing overheats the motor until the thermal fuse trips, so large batches are split into rounds with pauses.
  • Pressing with the pusher: pushing hard does not speed up juicing but slows the disc or auger and overloads the motor, a light guiding push is enough.
  • Unsuitable produce: nuts, frozen berries and sugar cane are not allowed for every model, so check the list in the manual first.

Caring for the strainer and auger

The strainer and auger are rinsed right after juicing, before the pulp dries: dried fibers clog the mesh holes, and the next run starts with imbalance and extra load on the motor. A soft brush from the kit or an ordinary toothbrush suits the mesh, while steel scourers and abrasive powders scratch it and widen the holes. A dishwasher does not suit every part, since hot drying warps a plastic auger and dries out rubber seals, after which the bowl starts to leak. The O-rings are wiped after washing and put back in place without stretching. The motor base is never put under water: it is wiped with a damp cloth, making sure no water gets into the vents. From time to time it helps to soak the strainer in warm water with citric acid, as fruit acid deposits come off easily without damaging the mesh.

When repair makes sense and when it is easier to replace the appliance

Repair makes sense when the housing and motor are sound and the fault involves a replaceable part, such as the coupling, a gear, the strainer, the seal or the electrics. After free diagnostics we tell you directly whether the appliance is worth fixing and name the cost before work begins. Replacement is worth considering if a basic centrifugal model has both a burnt winding and a cracked housing, since restoring two major parts comes close to buying a new unit. For slow juicers with a sturdy gearbox and a metal shaft the math favors repair, because their design is built for long service and mostly the replaceable parts wear out. It is easier to decide when you know the exact cause of the fault, and that is why our diagnostics are free. If the unit was bought recently and has never been opened, first check whether the store warranty is still valid.

Key points on juicer repair

We have gathered the essentials on how to find the faulty part from the symptom, choose the repair format and avoid a repeat breakdown after parts are replaced.

  • The symptom points to the part: humming without rotation relates to the drive, a failure to start to the lid lock, and a drip under the base to the shaft seal.
  • The design sets the weak spots: centrifugal models suffer at the strainer and carbon brushes, slow ones at the gearbox, the auger itself and the seal.
  • Diagnostics come first: the cause and cost are determined after checking the electrics and mechanics under load, not from a description over the phone.
  • The format depends on the fault: electrics and replaceable parts are changed at home, while the gearbox and motor need a full teardown at the service center.
  • Care extends service life: cutting hard vegetables, pausing during operation and washing the strainer right after juicing noticeably reduce the load on the drive.

34brands

Which juicer brands we repair in Almaty

We work with centrifugal, slow (masticating) and citrus models. Mention the brand and model in your request.

We also repairWe also repairTECH SERVICE09

Besides juicer repair, we fix other equipment in Almaty

Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.

BlogBlogTECH SERVICE10

Worth reading before juicer repair in Almaty

Leave a review

Choose a platform — the TECH SERVICE page will open.

2ГИС2GISGoogle MapsЯYandex Maps
Send a review with photos on WhatsApp