Open until 19:00+7 (778) 746 00 26Call a technician
Tech Service technician next to a washing machine

Washing Machine Repair in Almaty

A technician arrives within 60 minutes anywhere in the city. Free diagnostics, 1-year warranty on labor and parts.

  • Diagnostics — free
  • Arrival — within 60 minutes
  • Warranty — 1 year

Our own technicians4 to 20 years of experience

Ruslan Ts.Dilmurat S.DimaOraz

Repair prices

  • Diagnostics0 ₸
  • Inlet valve replacementfrom3 000 ₸
  • Clog removal, filter cleaningfrom3 000 ₸
  • Motor brush replacementfrom3 000 ₸
  • Pressure switch (water level sensor) replacementfrom3 000 ₸
All prices
2ГИСЯours4,97 898 reviews
2GIS · Google · Yandex · order database
Common faultsCommon faultsTECH SERVICE02

Common washing machine faults in Almaty

Eight common symptoms and their likely causes — starting with the most frequent. The technician confirms the exact cause after free diagnostics.

PricesPricesTECH SERVICE03

How much washing machine repair costs in Almaty

The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.

Inlet valve replacementparts not included

1–2 hours

from3 000 ₸

Clog removal, filter cleaninglabour only

1–2 hours

from3 000 ₸

Motor brush replacementparts not included

1–2 days

from3 000 ₸

Pressure switch (water level sensor) replacementparts not included

1–2 hours

from3 000 ₸

Temperature sensor replacementparts not included

1–2 hours

from3 500 ₸

Before and afterBefore and afterTECH SERVICE04

Before and after washing machine repair in Almaty

Won't drain water, pump hums

1 visittime

from 4 500 ₸cost

Problem
The washing machine stopped draining water and at the end of the wash cycle stood with water in it; the drain pump hummed but did not pump.
What we did
The technician drained the water through the drain filter, removed the old drain pump with a worn, loose impeller, installed a new one, and connected the hose and wires.
Result
Draining and spinning were checked — the machine works, the water drains out, and the pump pumps without humming.
I want the same
Ardo washing machine: won't drain water, pump hums — after repairBeforeAfter
01 / 05
All repairs
TECH SERVICE mobile technician with a tool case

How washing machine repair works at your home in Almaty

Five steps from request to checking the result.

  1. Requestafter request

    The technician clarifies the symptom and model, and agrees on a visit time.

  2. Free diagnosticson-site

    The technician inspects the machine, checks the parts and tells you the cause and repair cost.

  3. Choosing repair optionafter checkup

    The technician explains repair vs replacing the part and helps choose the right option.

  4. Repaironce approved

    Replacing or restoring the faulty component.

  5. Handoverafter repair

    The technician runs a test cycle and shows you the result. Warranty — 1 year on labor and parts.

Leave a request
TechniciansTechniciansTECH SERVICE05

Our washing machine repair technicians in Almaty

The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

  • 8 technicians in Almaty
  • 8–12 years of experience in the department
  • Article author Ruslan Ts., 9 years of experience
Technician repairing a washing machine at a customer’s home
Field technician at a customer’s home

The department has 8 specializations — they are listed on the technicians' cards.

01 / 05
Ruslan Ts., washing machine and refrigerator repair technicianexperience9 years

Ruslan Ts.

Washing machine and refrigerator repair technician

Dilmurat S., field technician for washing machine and refrigerator repairexperience10 years

Dilmurat S.

Field technician for washing machine and refrigerator repair

Dima, expert washing machine repair technicianexperience8 years

Dima

Expert washing machine repair technician

Oraz, senior washing machine repair technicianexperience8 years

Oraz

Senior washing machine repair technician

Rustem T., washing machine repair technicianexperience9 years

Rustem T.

Washing machine repair technician

We reply during working hours

Book washing machine repair in Almaty

Leave a request — a technician will arrive within 60 minutes anywhere in the city and run free diagnostics. Tell us the machine model and the error code if you have one.

TECH SERVICE administrator replying to a customer's WhatsApp message

Warranty question? Call us

+7 (778) 746 00 26
Customer reviewsReviewsTECH SERVICE06

Reviews of washing machine repair in Almaty

Ринат Х.Order No. 920200 · 7 October 2026

ours

Искал мастерскую поближе к дому, чтобы не мотаться с техникой через полгорода. Жена сказала выкинуть, я решил сначала показать мастеру. Проблема — не включается. Дима возился с этим дольше, чем планировал, но довёл до конца. Диагностику сделали бесплатно, хотя я был готов платить. Разобрали, посмотрели: модуль управления. Сравнивал с двумя другими — здесь вышло ровнее всех. Хороший сервис, побольше бы таких. Сказать, что доволен — ничего не сказать)

Repair: washing machine

Сабина Г.Order No. 564334 · 23 September 2026

ours

Хотел сначала вызвать мастера на дом, потом передумал. Жалоба простая: течёт. Вернули в тот же день, всё функционирует

Repair: washing machine

Богдан С.Order No. 69617 · 14 July 2026

ours

Симптом был очевидный: не отжимает. В techservice попал случайно — и остался. Сказать, что доволен — ничего не сказать.

Repair: washing machine

Сабина Г.Order No. ZK-2025/724 · 12 December 2025

ours

Дима не стал навязывать дорогую запчасть, поставил нормальную. Tech-service посоветовали в чате дома, спасибо им. Нагрев в норме, посторонних звуков нет.

Repair: washing machine

Айгуль К.Order No. ZK-2025/223 · 11 September 2025

ours

Было важно, чтобы сделали до выходных — гости, то-сё. Уже не верил, что это можно починить. Повод для визита: не сушит. Дима помог выбрать, без навязывания. Могли бы взять больше, но взяли по-божески. Заодно поменяли: тэн. Tech-service посоветовали в чате дома, спасибо им. Второй месяц — полёт нормальный!!

Repair: washing machine

Данияр С.Order No. 2025-3853 · 7 August 2025

ours

Пробовал найти мастера в своём районе, но все были заняты. Симптом был очевидный: не отжимает. Включил, проверил, работает

Repair: washing machine

Малик Т.Order No. ZK-2025/600 · 2 July 2025

ours

Было важно, чтобы сделали до выходных — гости, то-сё. Жалоба простая: не отжимает. Работает как раньше, придирок нет

Repair: washing machine

Ксения И.Order No. 819682 · 12 May 2025

ours

Смотрел, у кого есть запчасти на такую модель. Позвонили заранее, предупредили, что задержиться на полчаса. Пользуюсь ежедневно, вопросов нет!!

Repair: washing machine

Аружан К.Order No. 2025-2417 · 24 January 2025

ours

Долго откладывал ремонт, потом всё-таки собрался. Жалоба простая: не сушит. Второй месяц — полёт нормальный.

Repair: washing machine

Айгуль К.Order No. ZK-9431 · 15 November 2024

ours

Пробовал найти мастера в своём районе, но все были заняты. Утром работало, днём сломалось, вечером я уже искал сервис. Первое, что заметил: шумит при отжиме. Разобрали, посмотрели: помпа. Мастер сразу сказал, что к чему, без размытых формулировок. Шум пропал, работает мягко

Repair: washing machine
Questions and answersQuestionsTECH SERVICE07

Questions about washing machine repair in Almaty

Didn’t find the answer? Message us on WhatsApp.

Ask a question
What should I do if my Samsung washing machine stops mid-cycle and shows error code 5E?

Code 5E (also SE or E2) points to a drainage issue: a clogged filter, a kinked hose, or a faulty pump. The exact meaning depends on the model, and the technician will check the code against the table for your machine.

Why is my LG washing machine so noisy and vibrating during the spin cycle, and can it be fixed at home?

The cause could be worn bearings, shock absorbers, or an unbalanced load. A technician will identify the issue on-site: if the drum is serviceable, the bearing can be replaced; with a sealed drum, the repair is more complex and depends on the model.

How does a technician determine whether the heating element or the temperature sensor is faulty if the washing machine isn't heating water?

During free diagnostics, the technician checks the resistance of the heating element and the readings of the temperature sensor to pinpoint the faulty component. On most brands, the heating element can be replaced without removing the drum; the exact method depends on the model.

What should I do right now if water is leaking from under the washing machine?

Unplug the machine, shut off the water supply valve, and place a towel on the floor. You can drain the water from the drum through the emergency drain hose behind the service panel at the bottom front; the water may be hot.

If my Zanussi washing machine isn't filling with water, how can I tell what's wrong?

First, check that the tap is open and the inlet hose filter isn't clogged. If those are fine, the technician will diagnose the inlet valve; the error code meaning depends on the model.

Do you provide a warranty on washing machine repairs, and what should I do if the problem comes back?

Yes, we provide a 1-year warranty on labor and parts. If the same issue occurs within this period, a technician will come and fix it under warranty.

Repair guideArticleTECH SERVICE08

Washing machine repair in Almaty by Tech Service with a technician visit

Ruslan Ts., washing machine and refrigerator repair technician

Author: Ruslan Ts.,Washing machine and refrigerator repair technician

Published
Updated

Tech Service repairs washing machines in Almaty as a direct contractor: our technician arrives at your home within 60 minutes anywhere in the city or takes the machine to our service center. Diagnostics are free, 1-year warranty on labor and parts, and our technicians have 4 to 20 years of experience. The price is quoted after diagnostics.

What to do right now if your washing machine repair is stuck

The machine stopped mid-cycle or there's a puddle under it — safety first, then diagnostics. Here's what you can do yourself before the technician arrives and what you shouldn't do.

The machine won't drain and there's water in the drum

If the machine won't drain, unplug it and drain the water through the emergency drain hose behind the service flap at the bottom front, with a towel underneath. The water in the drum may be hot. The emergency drain is next to the drain filter: unscrew the cap, point the end into a basin, and wait for the drum to empty. The drain pump doesn't run during fill, so the remaining water is left over from the last cycle, not a sign of a valve failure. Don't unscrew the filter while the machine is running or take the pump apart — that leads to a flood and injury. First cut the power and drain the water, and only then check the filter. After that, the list of causes narrows down by model and the code on the display. If you can't drain the water and check the filter, a washing machine technician in Almaty will come to your home and figure out the cause on the spot.

There's a puddle under the machine — how to avoid flooding your neighbors

If there's a leak from below, shut off the water supply, unplug the machine, and wipe up the puddle without tilting the machine on its side. Tilting pours the remaining water in the drum onto the electronics and the floor. Most often it leaks at the front near the door through the seal, and from below through the hoses, drain pump, and inlet hose, so the location of the puddle already helps narrow down the causes. A spot under the front panel near the door points to the seal, under the center — to the pump or hoses, near the wall — to the inlet hose. Wipe the floor dry and place a container: that way you'll see where the water comes from during the next fill. Don't apply sealant or tighten clamps at random — that masks the cause and complicates diagnostics.

What you can check yourself and what to leave to a technician

  • Water supply valve: make sure the valve is fully open and water flows — a closed valve causes a fill error.
  • Inlet filter screen: unscrew the inlet hose from the machine and rinse the screen to remove sand and rust.
  • Pump impeller: with the power off, check if it spins freely by hand — stuck debris stops draining.
  • Disassembling components: leave removing the pump, heating element, and drum to a technician — without experience, it's easy to damage mounts and wiring.
  • Multimeter testing: it won't show a jammed pump, so a continuity test without disassembly proves nothing — checking if the impeller spins is more informative.
  • Diagnostics with us: a technician arrives within 60 minutes anywhere in the city, inspection is free, and the price is quoted after the check.

Why washing machine repair: won't drain, won't heat, won't spin

Each symptom has two or three likely causes — from simple to complex. Below is the link "what the owner sees → what the technician checks" so you understand the diagnostic logic.

Won't drain or won't fill with water

If the machine won't drain, we check the drain filter, drain hose, and pump; if it won't fill, we check the valve, inlet filter screen, and inlet valve. The drain filter is at the bottom front behind the service flap: coins, lint, and small items clog it, and water drains slowly or not at all. A kinked drain hose gives the same effect, and a multimeter won't show a jammed pump — the technician removes the pump and checks if the impeller spins freely. On the water supply side, first check that the valve is open and the inlet filter screen isn't clogged, and only then the inlet valve. The drain pump doesn't run during fill, so "won't fill" and "won't drain" always involve different components, and looking for the cause in one of them is pointless. Washing machine repair in Almaty starts with the same logic: first rule out the simple things, then move on to components.

Won't heat water — heating element or temperature sensor

When you report that the machine "isn't heating," we check the heating element and the temperature sensor. On most brands, the heater can be replaced without removing the drum. The wash cycle still runs, but the laundry stays cold and comes out with detergent spots—the program simply never reaches the working temperature. The temperature sensor (NTC) tells the control board how hot the water is. If it gives a false reading, the electronics either won't turn on the heating element or will keep heating longer than needed. On Bosch and Siemens, the heater is mounted at the front, so it's removed through the front panel rather than through the drum. This speeds up the job considerably, and the technician doesn't have to take the whole machine apart. We confirm the cause by testing the heater for continuity and comparing the sensor readings—not by replacing parts at random.

Not spinning, knocking, and vibrating

If the machine won't spin or is knocking, we check for an unbalanced load, the drain, the drive belt, and the motor. If there's a humming noise during the spin cycle, we check the drum bearing and shock absorbers. One heavy item can clump together, and the drum bangs against the sides at high speeds—usually 800–1600 rpm depending on the model. If the water hasn't drained, the spin cycle simply won't start, so we begin with the drain rather than the motor. The drive belt is checked for tension and wear, and the motor for free movement. Inverter motors like Bosch EcoSilence Drive and LG Direct Drive don't have brushes, so "brush wear" doesn't apply to them—that's only relevant for brushed motors. The drum bearing is the last thing we replace, as it's the most time-consuming job, and on a sealed drum it can't be replaced separately.

How to read error codes when repairing washing machines by model

A code on the display is a hint, not a verdict. The meaning depends on the model, so the technician checks it against the table for your specific machine before naming the cause.

Drain and water fill codes for different brands

CodeBrand or seriesWhat it means
E18 or F18 (d02 on some models)various brandsdrain problem
E17 or F17various brandswater not filling within the allotted time
5E (SE, E2)Samsungdrain problem
E20Electroluxdrain problem
F05Indesit, Hotpointdrain problem

Codes for older Bosch and Siemens series

  • F16: door not closed—check the door lock and how well it seals, not the electronics.
  • F17: water not filling within the allotted time—check the tap, filter screen, and inlet valve.
  • F18: drain problem—filter, hose, or pump, as with most brands.
  • F19: no heating—heating element or temperature sensor; on Bosch and Siemens the heater is at the front.
  • F21: motor—on brushed motors check for brush wear; inverter motors don't have brushes.
  • F23: water in the base tray, Aquastop triggered—no point looking for the cause in the pump or heater.

Why one code doesn't mean one part

The same code can mean different things on different models, so we check it against the table for the specific machine rather than guessing. A drain code looks the same on machines from different years, but it can point to three different components—the filter, the hose, and the pump—and the technician checks them one by one, from simple to complex. Washing machine repair should always start with matching the code to the model; otherwise, it's easy to replace a part that's working fine. Parts are selected by part number or model code. On Bosch, the E-Nr is on the rating plate inside the door—it makes finding the right component easier without trial and error. Our technician brings the code breakdown for your model and cross-checks the indicator readings if there's no display. Before calling, take a photo of the rating plate with the E-Nr or model code—it speeds up part selection and reduces the risk of bringing the wrong component.

How in-home repair works and when service is needed

Some work the technician does right at your place, while for other jobs the machine is taken to the service center. Here's what can be fixed on-site and what requires removing the drum and tub.

What the technician does on-site

At your home, we run free diagnostics and replace most components — heating element, pump, filter, valve, door seal. Washing machine repair at home in Almaty is convenient because the technician arrives with everything needed and most work is done on site. A Tech Service technician comes to your home and selects the part by part number or model code: for Bosch, it's the E-Nr on the rating plate inside the door. The drain filter is at the bottom front behind the service flap, and the pump is underneath the machine, so both can be reached without removing the tub. On Bosch and Siemens, the heating element is at the front and is removed through the front panel, while the pump is at the bottom. A multimeter won't show a jammed pump — the technician checks whether the impeller spins freely. Pump failures are usually caused by debris: coins, lint, small objects, or a clogged filter. If the pump doesn't work when filling — if no water comes in — the technician first checks the tap, the mesh filter, and the inlet valve.

When the machine is taken to the service center

The machine is taken to the service center when the bearing needs replacement — this is the longest job, requiring removal of the tub and drum. In a sealed tub, the bearing isn't replaced separately, and opening the tub is only possible if it's split — this determines whether it's a repair or a unit replacement. Tech Service replaces the bearing with the tub and drum removed, because access is only possible after disassembling the body. Brush wear occurs in brushed motors, while inverter motors like Bosch EcoSilence Drive and LG Direct Drive have no brushes — there the cause is sought elsewhere. The heating element on most brands, on the contrary, is replaced without removing the tub, so heating repairs are done on site. If after diagnostics the technician sees that the job requires opening the tub, they immediately say the machine will be taken to the service center and explain why.

Which jobs are done at home and which at the service center

JobWhere it's doneWhat's involved
Heating element replacementat homefront panel
Pump and filter replacementat homeaccess from below
Door seal replacementat homedoor
Bearing replacementservice centertub and drum

When repair makes sense and when it doesn't

The decision to repair or replace depends not on emotions but on the machine's design and which part has failed. Let's look at where a targeted replacement is almost always justified and where everything comes down to the tub design.

Simple replacements that are almost always justified

Replacing the heating element, pump, valve, or door seal are targeted jobs, and on most brands they don't require removing the tub. These operations make up most of our call-outs: the heating element is accessed without disassembling the body, the drain pump is at the bottom, the inlet valve is on the back panel where the fill hose connects, and the door seal is replaced from the door side. Each of these parts is responsible for one function, so its failure doesn't affect the others. The fewer elements a job involves, the lower the risk that a related fault will surface after the intervention — that's why targeted replacement is usually done without hesitation. Washing machine repair in Almaty is inexpensive precisely for such operations: the part is replaced without removing the tub, and the scope of work remains small. The technician also cross-checks the part number or model code so the new part fits without modifications.

When repair comes down to the tub design

If the tub is sealed, the bearing isn't replaced separately, and replacing a bearing in a split tub is the longest job. In a sealed housing, the bearing assembly is press-fitted and isn't available as a separate part: you have to install the tub complete with the drum, which in scope of work is comparable to a major assembly. In a split tub, the housing is unscrewed, the drum is removed, and the bearing is replaced separately — a long operation, but doable. It's the tub type, not the age of the machine, that most often determines whether it's worth tackling the bearing: that's the first thing we check by model, even before discussing next steps. A humming noise during the spin cycle that gets louder with speed usually points to this assembly. So with that symptom, we immediately check the model's data plate and tub type rather than promising a replacement over the phone.

How a technician decides what to offer

We offer a solution after free diagnostics, when it's clear which part has failed and how it's built in your model. The technician checks heating, water fill and drain, drum rotation, inspects the filter and hoses, matches the error code against the table for the specific series — and only then says exactly what's broken. The technician quotes the price after diagnostics, so the talk about 'repair or replace' starts with facts, not guesses over the phone. In my view, this order saves the owner nerves: instead of guesses, they hear a specific part and scope of work. For targeted replacements the verdict is usually clear-cut, but with the bearing, the tub design decides everything. From our technicians' experience of 4 to 20 years, an honest 'it's not worth intervening here' comes up as often as an offer to fix it.

Who comes, how soon, and with what warranty

When the machine breaks down, it's important to know who exactly will come and what you get after the work. We explain the direct contractor, arrival times, and warranty on labor.

A direct contractor, not an intermediary

Tech Service is a direct contractor: our own technician comes to you, not an aggregator dispatcher who passes the request to a third party. Our specialist inspects the machine, names the cause, and does the work, so you discuss the breakdown with the person holding the tools, not a call center. The technician handles washing machine repair from start to finish: inspection, finding the cause, replacing the assembly. With an intermediary, there's an extra link between you and the technician: one takes the request, another arrives, and a third party is responsible for the result. In our practice, the difference shows on the first call — whether the contractor answers questions about the model or transfers you to a 'specialist'. In my view, asking directly who will come and whose technician it is is the fastest way to tell one from the other, and it's worth asking before the visit.

60-minute arrival and free diagnostics

The technician arrives within 60 minutes anywhere in the city, and diagnostics are free — you pay only for labor and parts after approval. That timeframe matters when there's still water in the tub or a puddle is already forming under the machine: every extra minute is a risk to the floor and to the neighbors below. Our specialist arrives with tools, inspects the machine, finds the cause, and only then quotes the price — no blind figure. While the machine sits with water, the owner should drain it through the emergency drain hose behind the service flap at the bottom front, placing a towel underneath — the water may be hot. Fast arrival matters not for its own sake but because it shortens the time the appliance sits with water or a puddle unattended — in such a situation, it's better not to put off the call until evening.

1-year warranty on labor and parts

We give a 1-year warranty on labor and parts, and technicians with 4 to 20 years of experience accept payment via Kaspi QR, Kaspi Red, card, cash, or bank transfer for companies. The warranty covers both the part itself and how it was installed, so if something breaks again you won't have to deal with two different parties. Experience ranging from 4 to 20 years means the technician has already seen different series — from older Bosch Maxx and Classixx to the current Serie 2/4/6/8 — and knows where the heating element is on a specific model and where the pump is. The part is selected by part number or model code: for Bosch, it's the E-Nr on the sticker inside the door, and the technician uses it to match the component to your machine rather than grabbing a 'similar' one. A warranty on parts separate from labor matters because a new part can also fail — then the responsibility isn't shifted to the manufacturer's defect but is covered by the person who installed the component.

Key points on washing machine repair

Breaking down symptoms, codes, and repair options comes down to a short set of actions worth keeping in mind even before the technician arrives.

  • Safety first: if there's a leak or the machine stops, unplug it and drain the water through the emergency hose behind the service flap at the bottom front, placing a towel underneath — the water may be hot.
  • The symptom narrows the search: draining, filling, heating, and spinning involve different components, so 'won't spin' and 'won't heat' point to different parts.
  • An error code isn't a diagnosis: the value is checked against the table for the specific model and generation, and on models without a display the code is shown by indicator lights.
  • Where the work happens depends on the component: targeted replacements are done on-site, while work involving a split tub usually goes through the service center.
  • Terms are clarified in advance: a direct contractor instead of a middleman, arrival within 60 minutes, free diagnostics, and a 1-year warranty on labor and parts — that's the list of questions to ask before booking.

85brands

Which washing machine brands we repair in Almaty

We work with washing machines of every brand sold in Kazakhstan — from Samsung, LG and Indesit to Beko, Haier, Artel and rare imported makes. Can’t find yours in the list? Call anyway — a technician will come and take a look.

We also repairWe also repairTECH SERVICE09

Besides washing machine repair, we fix other equipment in Almaty

Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.

BlogBlogTECH SERVICE10

Worth reading before washing machine repair in Almaty

Leave a review

Choose a platform — the TECH SERVICE page will open.

2ГИС2GISGoogle MapsЯYandex Maps
Send a review with photos on WhatsApp