experience10 yearsMaksim S.
Graphics card repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 096 59 70Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Free diagnostics, 1-year warranty on labor and parts.
Our own technicians4 to 20 years of experience




Repair prices
Below are typical symptoms and their likely causes. The exact cause will be determined by the technician during free diagnostics.
Dirty sensors, worn rollers
from6 000 ₸
Worn rollers, misaligned guides
from7 500 ₸
Code points to feed unit
from5 500 ₸
Calibration drift, sensor wear
from6 000 ₸
Worn bearings, loose fasteners
from6 500 ₸
Clogged guides, worn belt
from7 500 ₸
Power supply, fuse, button
from6 500 ₸
Worn rollers, dirty paper path
from7 500 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1–2 hourstime
from 3,000 ₸cost

BeforeAfter5 steps

From request to check — five steps, free diagnostics.
Leave a request, the technician will clarify the model and symptoms.
The technician arrives anywhere in the city within 60 minutes after the request.
The technician confirms the address and a convenient time slot to avoid rescheduling.
A test run with banknotes of various denominations confirms counting accuracy.
We provide a document confirming a 1-year warranty on labor and parts.
The computer and laptop repair department in Almaty has 7 technicians with 6 to 15 years of experience.

The department has 7 specializations — they are listed on the technicians' cards.
experience10 yearsGraphics card repair technician
experience6 yearsPC and laptop diagnostics technician
experience8 yearsLaptop repair engineer
experience10 yearsSoftware installation specialist
experience7 yearsPC and laptop repair technician
experience13 yearsDiagnostics and virus removal specialist
experience15 yearsConsultant
We reply during working hours
Specify the model and symptom — the technician will schedule a convenient time and prepare for the visit.

Warranty question? Call us
+7 (778) 096 59 707 898 reviews of repairs at TECH SERVICE in total
Мадина Т.Order No. ZK-6492 · 26 January 2026
oursПриехал без записи, приняли. Дамир М объяснил причину так, что понял даже я. Перезвонили, когда можно было забирать. Цену сказали сразу, без «ну потом посмотрим». Отношение нормальное, без высокомерия. Всё объяснили простыми словами. Дали гарантию и рекомендации на будущее. Сделали ровно то, о чём договаривались. Сделали аккуратно, следов разборки не видно.
Станислав К.Order No. 2025-6394 · 13 October 2025
oursСервис нашёл случайно, но остался доволен. Искал мастерскую поближе к дому, чтобы не мотатся с техникой через полгорода. Пять звёзд, не задумываясь.
Гульмира С.Order No. TS-2405-628 · 21 January 2024
oursПозвонил, когда техника встала окончательно. Запчасть нашли без проблем. Работали аккуратно, ничего не поцарапали. Приняли технику, выдали квитанцию. Перезвонили, когда можно было забирать. Приняли быстро, объяснили, что и как будет. Проверили при мне, показали результат. Отношение нормальное, без высокомерия. Цена не изменилась ни на тенге. Проверил дома — всё на месте, ничего не забыли.
Эльмира Т.Order No. 2023-8970 · 18 August 2023
oursПозвонил утром, к обеду уже всё решили. Хороший сервис, побольше бы таких.
Жанар Т.Order No. 917484 · 17 March 2021
oursПозвонил утром, к обеду уже всё решили. Чуть дольше, чем обещали, но предупредили. Приняли быстро, объяснили, что и как будет. Приняли технику, выдали квитанцию. Не пришлось ничего доказывать и просить. Хороший сервис, побольше бы таких)
Тимур А.Order No. TS-8148 · 8 March 2021
oursПозвонил утром, к обеду уже всё решили. По срокам не подвели. Ставлю пятёрку.
Кристина Л.Order No. TS-9549 · 24 December 2020
oursПришёл по записи, всё прошло спокойно. В общем, доволен. Оформили всё официально, с гарантией.
Дарья С.Order No. TS-9025 · 6 September 2018
oursПришёл по записи, всё прошло спокойно. Позвонил знакомому, он раньше работал в сервисе, посоветовал этих. Максим Снегирев всё объяснил и не пытался впарить лишнее
Азамат Е.Order No. 2017-8299 · 11 November 2017
oursВыбирал между несколькими сервисами, остановился на этом. Пробовал найти мастера в своём районе, но все были заняты. Раис Мирзахметов взялся за то, от чего другие отказались. Мастер посмотрел, назвал причину, всё разложил по полочкам. Не идеально, но честно.
Станислав К.Order No. TS-1711-551 · 10 January 2017
oursБыла срочная поломка, нужен был мастер сегодня. Не понравилось, что нужно оставлять предоплату
Didn’t find the answer? Message us on WhatsApp.
Ask a questionCheck that the plug is firmly in the outlet, the power cord is intact, and the outlet itself works. If there's power but the machine stays silent, the cause may be a fuse or the power supply — that's a job for a technician.
Yes, in most cases this repair is possible. The technician will take the machine apart, clean the paper path and circuit boards, dry them, and replace any damaged components. It depends on the model and whether the board has been affected.
If the notes pass through smoothly, without jams or jerks, but the machine doesn't recognize them or mixes up denominations, the sensor is the likely culprit. Mechanical problems usually come with unusual noise or notes getting chewed up.
Yes, depending on the model, the firmware can be updated so the machine correctly recognizes Kazakhstani banknotes. The technician confirms whether an update is possible after diagnosing the specific device.
Jammed and torn notes become unusable, and the wear on the rollers and paper path gets worse. The sooner a technician inspects the machine, the fewer parts will need replacing.
If the machine is old, spare parts are hard to find, and breakdowns keep happening one after another, repair may not be worth it. After free diagnostics, the technician will tell you what makes more sense — restoring the equipment or upgrading your fleet.
Tech Service repairs banknote sorters and counters in Almaty: a technician comes to your home within 60 minutes or the work is done at our service center. Diagnostics are free, there is a 1-year warranty on labor and parts, and our technicians have 4 to 20 years of experience. We provide the price after diagnostics.
A sorter stops counting bills for several common reasons, from dirty sensors to corrupted firmware. Here's how to tell one fault from another before the technician arrives.
Most often, the machine stops counting because of dust and paper particles on the optical and UV sensors—they stop 'seeing' the bill. Humid air and operation in a room without ventilation speed up the process: dust mixes with paper particles and settles in a dense layer on the lenses and along the edges of the feed path. The device still turns on, the rollers spin, but recognition fails—the count skips bills, and the note goes to the reject bin. Optical sensors are responsible for the bill's image, UV sensors for security marks, and contamination of any unit breaks the entire verification chain. If counting doesn't recover after carefully blowing out the path, the problem is not dust but a sensor or calibration—cleaning with alcohol on your own only drives dirt deeper.
We update the firmware and denomination database for tenge when the machine stops recognizing denominations after a banknote change or a failed update. The firmware contains a database of tenge banknotes, and denomination sensors compare each bill's image against it—if the database record is outdated, the device sees the bill but cannot assign a denomination. In our practice, such requests come in waves after new series are introduced: the mechanics are fine, but the counter gives a recognition error or stacks different denominations in one compartment. Updating the firmware and denomination database restores correct counting without replacing components. If the counter confuses denominations only on new banknote series but counts old ones correctly, that's a sign of an outdated database, not a mechanical failure.
Bill jams and error codes on the screen are the most common reasons to call a technician. Here's what's behind each symptom, which unit to check first, and when you can't do without a specialist visit.
We fix jamming and tearing in the path—usually the cause is worn feed rollers and pressure mechanisms that skew the bill. Feed rollers grab the sheet and pull it through the path to the sensors; when their surface wears down, the force on one side drops, and the paper moves at an angle. Pressure mechanisms add a second cause: weakened pressure no longer holds the sheet straight, and at the exit of the path the bill gets crumpled or torn along the edge. Jamming in this unit almost always repeats at the same position in the path—that's how the technician identifies the worn roller. If only old bills tear while new ones go through smoothly, the rollers are still alive but the pressure is weak; it's better to replace them before a torn bill completely clogs the path.
We repair counters that won't turn on — checking the power supply, fuse, and control board, starting with the simplest causes. The power supply sends voltage to the control board through a fused circuit, and a break anywhere in that chain means complete silence: no backlight, no response to buttons. First the technician checks the cable and connector, then the fuse integrity, and only after that moves to the board itself — this rules out cheap causes before disassembling the case. On the control board, they look for signs of overheating, bulging capacitors, and damaged traces that appear after voltage spikes. If the device won't turn on after a power surge or moisture, don't keep cycling the power — that can finish off a board that could still be repaired.
The process follows a clear route: request, free diagnostics, on-site or in-shop work, then a counting test. We break down each stage so you understand what's happening with your device.
We come to you within 60 minutes anywhere in the city or repair in our shop — you choose the format based on the fault and convenience. The on-site technician brings tools for typical mechanical and electronic work, so most calls are resolved on the spot. Bringing the device to us is more convenient when deep disassembly of the feed path or control board replacement is needed. Minor issues — sensors, rollers, firmware — are usually handled on-site without transporting the device. Two-pocket models are heavier and more sensitive to transport, so they're often left with us. The decision is yours: some clients prefer to watch the technician work, others find it easier to free up their office during repair. If a board replacement is needed, it's more convenient to leave the device in the shop — at home such an operation is done less often due to conditions.
Whether to repair a two-pocket sorter or replace it depends on the condition of the board and feed path: if a unit can be restored by replacing parts, repair is justified. The control board handles counting logic and sensor operation, the feed path handles feeding banknotes without jams; when only one unit is worn, servicing usually makes sense. When both the board and feed path are worn and the model is no longer supported, investing in repair may not pay off — it's worth discussing with the technician before work. We honestly say when repairs no longer make sense: sometimes replacing equipment is more cost-effective than a series of repeat calls. Irreparable faults — cracks in the feed path housing, a burned-out board with no donor — are also a reason to consider replacement. The technician names the cause and options after free diagnostics, and the decision is yours.
The warranty and transparent pricing remove the main fear of cash equipment owners: that the machine will be fixed and then break down again a month later. Here we explain how warranty obligations work and what determines the final price.
We provide a 1-year warranty on labor and parts — it also covers replaced sensors, rollers, and the control board. If the same component fails again within a year, we fix the problem without charging again for labor or the part. The warranty period is the same for on-site service and for work done at our service center, so the location of the repair does not affect our obligations. Technicians record every replaced component in the work order — this record makes it easier to prove the connection between the repair and any subsequent malfunction. Our engineers, with 4 to 20 years of experience, know the typical weak points of the feed mechanism and optics, so repeat calls for the same component are rare. The warranty is valid only with careful use: if the device is flooded or dropped after repair, it is no longer a warranty case — keep that in mind.
The technician gives you the price after a free diagnostics — it depends on the breakdown and the parts that need replacing. Diagnostics is included in the visit and costs the owner nothing: first the engineer checks the optical sensors, the feed path, and the control board, then explains the scope of work. Replacing sensors and rollers is one cost level, repairing the control board is another, and they should not be confused. Asking for a price over the phone is pointless: the same error on the display can mean either cleaning a sensor or replacing the board — the difference in work is significant. Banknote sorter repair in Almaty is discussed with the technician after the inspection, when the real cause of the failure is visible, not the assumed one. The technician arrives anywhere in the city within 60 minutes, so diagnostics does not stretch into days of waiting.
We accept Kaspi QR, Kaspi Red, card, cash or bank transfer and service banking equipment under a contract for businesses — cash desks, shops, offices. A one-time call fixes a specific breakdown, while a service contract includes scheduled maintenance: cleaning the feed path, checking sensors and rollers before they start to fail. For businesses, this format is more cost-effective than one-time calls: scheduled maintenance reduces the number of sudden failures at the cash desk, and banknote sorter repair requests from regular clients in Almaty get priority. Our engineers work with cash counting equipment in bank branches and retail outlets, so they know the requirements for uninterrupted operation of the cash handling unit. The contract is made with the organization, not an individual employee — this makes it easier to keep records for all devices at once.
We service banknote counting equipment of various brands — from DORS and DoCash to Hitachi and Magner. Here we explain what fails in each category of device and which components we check first.
We service DORS and DoCash sorters — most often clients come with jams, worn rollers, and detection failures. Two-pocket models have a longer feed path with more points where the banknote bends, so the rubber rollers wear out noticeably faster than in compact single-pocket counters. Recognition failures in these brands are usually caused by dirty optics and a misaligned denomination database after careless transportation. For jams, we first check the condition of the pressure rollers and the feed path adjustment — worn rubber stops gripping the banknote evenly and pulls it at an angle. In two-pocket machines of these brands, the banknote path is longer, so sensor contamination builds up faster — maintenance should be done more often than on single-pocket models. Our technicians arrive within an hour anywhere in the city, and diagnostics is free.
We service Hitachi, Magner, and REAL CASH note counters and sorters — restoring authenticity detection and denomination recognition. These machines have several independent verification units: optical, magnetic, and ultraviolet. If any of them fails, it causes false triggers or missed notes. Denomination recognition depends on the image sensors working correctly — when they get dirty, the machine starts confusing banknotes with similar designs. After replacing measurement components, we calibrate detection using reference samples; otherwise, even a working unit will produce errors. In models with denomination detection, settings often get misaligned after repairs — without proper adjustment, the machine counts but mixes up different denominations. We provide a 1-year warranty on labor and parts.
| Category | What breaks most often | Typical repairs | What we check |
|---|---|---|---|
| Two-pocket sorters | rollers, feed path | roller replacement, path cleaning | feeding and sorting |
| Single-pocket counters | sensors, firmware | cleaning, denomination database update | denomination recognition |
| Note counters and sorters | detection calibration | sensor replacement, calibration | authenticity detection |
| Currency detectors | UV and magnetic units | sensor replacement | security feature verification |
Regular cleaning and maintenance extend the life of your sorter and reduce unexpected breakdowns. Here's how often to check components, what you can do yourself, and when it's time to call a technician.
We service banking equipment under contract — for checkout counters, shops, and offices where a stopped bill counter halts operations. Service includes scheduled maintenance: cleaning sensors and the feed path, checking rollers, and tuning counting parameters to your denominations. This schedule reduces sudden breakdowns, since roller wear and dirty optics are caught before the machine fails during peak hours. Each contract is assigned a technician with 4 to 20 years of experience, and completed work and parts come with a 1-year warranty. If the counter does fail, a technician arrives for diagnostics anywhere in the city within 60 minutes, and the inspection is free. In my view, for a location with daily cash flow, scheduled maintenance is cheaper than an emergency call at the height of a shift.
The takeaway: what really causes bill sorters to fail, how to tell a genuine breakdown from routine maintenance, and which criterion to use when choosing a service provider in the city.
8brands
Choose a brand to go to the page with models and services for your device.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your laptop screen is broken, turn the device off first, don't press on the display, and check the picture through an external monitor.
12 March 2026 · 11 minutes read
If your laptop freezes, the first thing to do is restart it and check Task Manager to see what's loading the CPU and memory.
25 January 2026 · 12 minutes read
If your computer won't turn on, start simple: check the outlet, power cable, switch on the power supply, and the power button.
19 January 2026 · 13 minutes read
If your laptop won't boot, first determine which of two states you're in: the device doesn't respond to the power button at all…
13 December 2025 · 12 minutes read












