Open until 19:00+7 (775) 030 02 94Call a technician
Tech Service technician next to a cooktop

Cooktop Repair in Almaty

A technician arrives within 60 minutes anywhere in the city. Diagnostics are free, and our technicians have 4 to 20 years of experience.

  • 1-year warranty on labor and parts
  • Arrival within 60 minutes anywhere in the city
  • You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies

Our own technicians4 to 20 years of experience

Ruslan Ts.Damir M.Dilmurat S.Dima

Repair prices

  • Diagnostics0 ₸
  • Panel unlockingfrom4 500 ₸
  • Mode switch replacementfrom5 000 ₸
  • Temperature sensor replacementfrom5 500 ₸
  • Wiring and terminal block repairfrom5 500 ₸
All prices
2ГИСЯours4,97 898 reviews
2GIS · Google · Yandex · order database
Common faultsCommon faultsTECH SERVICE02

Common cooktop faults in Almaty

Causes are listed from the most common. The technician pinpoints the exact component after diagnostics.

PricesPricesTECH SERVICE03

How much cooktop repair costs in Almaty

Choose a symptom to see the matching services and prices, excluding the cost of parts.

Panel unlockingexact price — after the free diagnostics

1–3 hours

from4 500 ₸

Mode switch replacementparts not included

1–2 hours

from5 000 ₸

Temperature sensor replacementparts not included

1–2 hours

from5 500 ₸

Wiring and terminal block repairparts not included

1–3 hours

from5 500 ₸

Relay and triac replacementparts not included

1–2 hours

from6 000 ₸

Before and afterBefore and afterTECH SERVICE04

Before and after cooktop repair in Almaty

False overheat error due to sensor

1 visittime

from 5 500 ₸cost

Problem
The induction cooktop on one zone after a few minutes dropped power and showed an overheat error, although the cookware remained cold.
What we did
The technician removed the panel, took off the glass, replaced the temperature sensor on the coil of this zone and checked heating at full power.
Result
The zone works again at full power without a false overheat error, heating checked.
I want the same
Beko cooktop: false overheat error due to sensor — after repairBeforeAfter
01 / 03
All repairs
TECH SERVICE mobile technician with a tool case

How cooktop repair works at your home in Almaty

Five steps from your request to checking the result.

  1. Requeston the day of the request

    Describe the symptom and the cooktop model so the technician brings the right tools.

  2. Preparationbefore the visit

    Tell us the model, the symptom and the surface type so the technician brings the right parts and tools.

  3. Approvalbefore the repair

    You get the list of work and the price before the repair starts and decide whether to go ahead.

  4. Repaironce you agree

    The work is done after you agree with the cause and the price.

  5. Handoverafter the repair

    You check the burners' heating and the touch controls yourself before signing off. 1-year warranty on labor and parts.

Leave a request
TechniciansTechniciansTECH SERVICE05

Our home appliance repair technicians in Almaty

The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

  • 8 technicians in Almaty
  • 8–12 years of experience in the department
  • Article author Ruslan Ts., 9 years of experience
Technician repairing a cooktop at a customer’s home
Field technician at a customer’s home

The department has 8 specializations — they are listed on the technicians' cards.

01 / 08
Ruslan Ts., washing machine and refrigerator repair technicianexperience9 years

Ruslan Ts.

Washing machine and refrigerator repair technician

Damir M., general household appliance repair technicianexperience12 years

Damir M.

General household appliance repair technician

Dilmurat S., field technician for washing machine and refrigerator repairexperience10 years

Dilmurat S.

Field technician for washing machine and refrigerator repair

Dima, expert washing machine repair technicianexperience8 years

Dima

Expert washing machine repair technician

Nikita M., field refrigerator repair technicianexperience8 years

Nikita M.

Field refrigerator repair technician

Oraz, senior washing machine repair technicianexperience8 years

Oraz

Senior washing machine repair technician

Radik T., dishwasher repair technicianexperience11 years

Radik T.

Dishwasher repair technician

Rustem T., washing machine repair technicianexperience9 years

Rustem T.

Washing machine repair technician

We reply during working hours

Book cooktop repair in Almaty

Request a diagnostic visit: technicians with 4 to 20 years of experience will find the cause of the fault and explain what needs replacing.

TECH SERVICE administrator replying to a customer's WhatsApp message

Warranty question? Call us

+7 (775) 030 02 94
Customer reviewsReviewsTECH SERVICE06

Reviews of cooktop repair in Almaty

Данияр С.Order No. 2026-1913 · 9 February 2026

ours

Позвонил знакомому, он раньше работал в сервисе, посоветовал этих. Была паника, если честно. Проблема — ошибка. Заявку приняли по телефону, перезвонили через десять минут. Нужна была замена: индукционная катушка. Вышло 22 500 тенге, дешевле, чем я рассчитывал. В тех сервис привёл знакомый, у него тут чинили ноут. Шум пропал, работает мягко)

Repair: stove

Нурлан Б.Order No. 51212 · 30 May 2025

ours

Цена имела значение, но и горонтия тоже. Повод для визита: не включается. Крутит ровно, без рывков.

Repair: stove

Асель Ж.Order No. TS-2404-216 · 17 April 2024

ours

Обратился по поводу варочной панели. С чем пришёл: не включается. Дамир М объяснил причину так, что понял даже я. Сказали 10 000, а потом ещё и скидку сделали. Поменяли: плата. Приняли без очереди, оформили за пять минут. Хороший сервис, побольше бы таких. Сказать, что доволен — ничего не сказать.

Repair: stove

Елена К.Order No. 56013 · 15 March 2022

ours

Утром работало, днём сломалось, вечером я уже искал сервис. Симптом был очевидный: ошибка. Радик Т возился с этим дольше, чем планировал, но довёл до конца. Назвали 26 500 сразу, в конце сумма не изменилась. Ребёнок уже проверил на прочность, держится.

Repair: stove

Гаухар Н.Order No. ZK-2783 · 28 December 2020

ours

Радик Т честно сказал, что менять, а что ещё походит. Под замену пошло: индукционая катушка. С тех пор ни разу не подвёл.

Repair: stove

Нурасыл М.Order No. TS-7169 · 24 July 2020

ours

Техника на гарантии уже не была, так что выбор был свободный. Долго искал, кому это отдать, и вот нашёл. Симптом был очевидный: не греет зона. Нужна была замена: плата. Проверили при мне, показали, что всё держит.

Repair: stove

Сауле Н.Order No. 23570 · 14 March 2020

ours

Друг посоветовал, у него похожая история была. Не думал, что вообще напишу отзыв, но тут стоит. Первое, что заметил: не включается. Радик Т возился с этим дольше, чем планировал, но довёл до конца. Договорились на утро, к девяти уже был свободный мастер. Смета совпала с итогом, что редкость. В techservice попал случайно — и остался. Проверили на всех режимах, всё чётко.

Repair: stove

Андрей П.Order No. 2020-8988 · 6 March 2020

ours

Долго откладывал ремант, потом всё-таки собрался. С чем пришёл: не греет зона. Включил, проверил, работает.

Repair: stove

Аружан К.Order No. ZK-6836 · 15 January 2020

ours

Техника на гарантии уже не была, так что выбор был свободный. Жалоба простая: не греет зона. Проверили на всех режимах, всё чётко.

Repair: stove

Светлана Д.Order No. 92173 · 14 March 2019

ours

Жалоба простая: не включается. Дамир М не стал навязывать дорогую запчасть, поставил нормальную. Ребёнок уже проверил на прочность, держится)

Repair: stove
Questions and answersQuestionsTECH SERVICE07

Questions about cooktop repair in Almaty

Didn’t find the answer? Message us on WhatsApp.

Ask a question
Can a cracked cooktop glass be replaced?

Yes, the glass-ceramic surface can be replaced separately if the body and mounts are intact. The technician selects glass for the specific model and, after installation, checks heating and sensor operation. It depends on the model: on some cooktops the glass comes as a unit with the frame.

Why does an induction cooktop hum and click during operation?

The hum comes from the cooling fan and the induction coils, while the clicks are from relays and triacs switching. If the sound has become louder than usual or crackling appears, it's worth having a technician look at the cooktop. It depends on the model: on some surfaces, noise during operation is considered normal.

Why does the cooktop turn itself off while cooking?

Most often a protection is triggered: overheating, a temperature sensor fault, or a poor contact in the terminal block. Sometimes the cooling fan that has stopped spinning is to blame. The technician will determine the exact cause during free diagnostics, with a visit in Almaty within 60 minutes.

What should I do if the cooktop sensor doesn't respond to touch?

First, wipe and dry the cooktop and disable the child lock according to the instructions. If the sensor still doesn't respond, the cause is in the ribbon cable or control board, and repair is needed. A Tech Service technician often fixes this fault on-site.

Which component usually fails if one induction zone stops heating?

Most often the induction coil of that zone, its power module, or a relay on the control board is to blame. Diagnostics show exactly what has failed, and only that component is replaced. It depends on the model: sometimes the coil comes as a unit with the board.

Does a built-in cooktop need to be removed from the countertop for repair?

Not always: the technician replaces the sensor, relay, and wiring on-site without removing the cooktop from the countertop. It has to be removed when board soldering or glass-ceramic replacement is needed. The technician will tell you what can be done on-site after free diagnostics.

Repair guideArticleTECH SERVICE08

Cooktop Repair in Almaty with a Tech Service Technician at Your Home

Ruslan Ts., washing machine and refrigerator repair technician

Author: Ruslan Ts.,Washing machine and refrigerator repair technician

Published
Updated

We handle cooktop repair in Almaty with our own technicians: induction, Hi-Light glass-ceramic and gas models are fixed at the customer's home or in our service center. A technician arrives within 60 minutes, diagnostics are free, and we quote the cost after them. We give a 1-year warranty on labor and parts and accept payment via Kaspi QR, Kaspi Red, card, cash, or bank transfer for companies.

What breaks inside an induction cooktop

An induction cooktop has three main components: the coils, the power module and the control board. Almost every fault points to one of them, so the technician knows where to look from the symptom alone.

Coil, power module and control board

An induction cooktop heats cookware with the alternating magnetic field of a coil, driven by a power module built on IGBT transistors that follows commands from the control board. Under each zone sits a copper coil with an NTC temperature sensor in its center that tells the board how hot the pan base is. The power module turns mains voltage into high-frequency current, so it runs hotter than anything else and is the first to suffer from voltage swings. A fan under the housing draws heat away from the transistors; once it clogs with dust and grease, the electronics overheat and heating cuts out mid-cooking. The control board takes commands from the touch panel and passes them to the zones. If one zone stops working while the others still heat, the cause is almost always local — the coil, its sensor or a power module channel, not the whole electronics.

Fault symptoms and the likely component

SymptomLikely componentWhat we check
Won't turn on, display darkPower supply, fuseInput voltage, fuse
One zone doesn't heatCoil, power module channelCoil resistance, transistors
Shuts off after a few minutesFan, NTC sensorFan speed, sensor readings
Loud humming and cracklingCoil mounting, cookwarePan base, coil mounting
Error code on the displayComponent from the model's tableCode meaning, sensor circuit

Why the induction zone doesn't detect the pan

Induction heats only cookware with a ferromagnetic base, so the first thing we do is test the pot with a magnet, and only then the electronics. Aluminum, copper, glass and some stainless steel don't react to the magnetic field, and the display honestly shows a flashing pan symbol. A base that is too small isn't recognized either: the zone expects the pan to cover a good part of its diameter. If the magnet sticks but there is still no heat, our cooktop repair technician in Almaty checks the coil, the temperature sensor and the power module channel that serves that zone. Our technicians have 4 to 20 years of experience and find this kind of fault with measurements right in your kitchen. A flashing pan symbol with suitable cookware is a reason to call a technician, not to buy a new set of pans.

How Hi-Light glass-ceramic cooktops are repaired

An electric glass-ceramic cooktop is simpler than induction, but it has its own weak spots: the burner coil, the thermal limiter and the relays on the board. Here is how they fail and what gets replaced.

How a Hi-Light burner is built

A Hi-Light burner is a ribbon heating element in an insulated dish under the glass that glows from the current and heats the pan through the glass-ceramic. Such a zone reaches working temperature within seconds and glows red, which makes it easy to tell apart from induction, where the glass under the pot doesn't glow. The ribbon is fixed to a ceramic base and wears out from heating cycles over time: the metal turns brittle, and knocks on the glass and overheating an empty pan speed up a break. In expandable zones two or three ribbons switch on separately, and one of them can fail while its neighbors keep working. A dark patch where the zone should glow while the indicator is on points to a broken ribbon, not to the board.

Thermal limiter, relays and power regulators

When a burner heats weakly or switches itself off, we check the thermal limiter and the board relays that control the ribbon. The thermal limiter, a rod-type sensor above the ribbon, opens the circuit when the glass overheats, and as it wears it starts tripping too early, so the zone heats in bursts. A relay on the control board switches the burner on and off according to the selected power level; its contacts burn, and the heat disappears. On models with rotary knobs the same job is done by an energy regulator, whose bimetal strip wears out. Our technicians measure the ribbon's resistance, check how the limiter trips and test the relay contacts, then replace only the faulty part. A stuck relay is more dangerous than a burnt one, because the burner heats nonstop, so it's better not to use such an appliance until it's repaired.

When the burner is replaced and when the board

We replace burners and relays at your home, while a board with damaged soldering sometimes goes to our service center. To reach the ribbon, the technician disconnects the power, lifts off the glass top and replaces the whole dish with its heater, since repairing the ribbon itself makes no sense. In-home cooktop repair like this is possible once diagnostics confirm the cause and the new burner matches the model in diameter and power. A board with burnt traces or signs of liquid damage is easier to restore in our service center, where it can be tested separately from the housing. The installed burner and the work done are covered by our 1-year warranty. Note in advance which zones and power levels don't work, so the technician can pick the right parts straight away.

Gas and combination models and their weak spots

Besides electronics, gas and combination models have flame failure protection and electric ignition. These are the parts behind complaints about a flame that goes out and clicking without a spark.

Why the flame goes out when you release the knob

The flame goes out after you release the knob when the flame failure thermocouple doesn't heat up or can't hold the solenoid valve open. A thermocouple is a thin metal rod next to the burner: in the flame it generates a small voltage, and as long as that voltage is there, the valve in the tap stays open. If the tip is sooty, bent or has moved out of the flame, the voltage falls short, and the gas supply cuts off after a few seconds. A second cause is a corroded contact between the thermocouple and the valve, and a third is wear of the valve itself. Flame failure protection exists for safety: if a draft blows the flame out or boiling soup floods it, gas stops flowing into the kitchen. If you have to hold the knob longer than usual, first check that the burner cap sits evenly over the thermocouple.

No spark from the electric ignition

When the igniter clicks without a spark or sparks constantly, we check the spark plug, the lead and the ignition unit. The unit generates high-voltage pulses and sends them to a ceramic spark plug at each burner. A crack in the ceramic, carbon buildup and moisture on the plug divert the discharge, and the gas doesn't light. When all the plugs click but none of them sparks, we look for the fault in the unit, while complete silence when you press means a problem with the unit's power. Constant clicking without pressing comes from a button that stuck after water and grease got in. Our technician finds this kind of fault with measurements and replaces the plug, the button or the unit without touching the gas fittings. Clicking after cleaning stops once the buttons and plugs dry out; if it hasn't stopped within a few hours, the button is to blame.

What the technician checks on a gas cooktop

  • Gas taps: we check that the knobs turn easily and that there is no smell of gas around the taps with the burners closed.
  • Thermocouples and valves: we measure the thermocouple voltage in the flame and check that the solenoid valve holds the gas supply.
  • Jets and burners: we clean clogged openings that make the flame burn yellow, blacken pans with soot and lift off the burner cap.
  • Electrical part: on combination models we separately check the Hi-Light burners, their regulators and the power to the ignition unit.
  • Safety before the visit: if you smell gas, shut the tap on the pipe, air out the kitchen and don't switch on appliances nearby.

Why the breaker trips and how the wiring is involved

Some faults start not in the cooktop itself but in the cable, the terminal block and the electrical panel. They are easy to mistake for an electronics failure, even though it is the connection that needs fixing.

What it means when the breaker trips at switch-on

A breaker that trips the moment you switch on points to a short circuit: a failed power module, burner or cable. If the protection cuts out not right away but after a few minutes at high power, an overloaded line is more likely: the breaker rating doesn't match the load, or an oven is connected to the same line. A tripping residual current device means something else, a current leak to the housing that appears when moisture gets inside the appliance and the insulation is damaged. On induction models, shorted transistors in the power module close the circuit, and the breaker trips when power is applied or when a zone is switched on. The technician tells these cases apart by which protection trips and when. Don't reset the breaker more than once in a row, because every switch-on into a short adds damage to the board and contacts.

Terminal block and power cable

We replace a blackened terminal block and a melted cable on site, then test the connection under load. The terminal block on the underside of the housing connects the cable wires to the electronics through jumpers that set the wiring scheme, single-phase or three-phase. A loose screw makes a poor contact: it heats up, the plastic darkens and melts, and the input voltage sags and disrupts the board. Owners sometimes take the appliance straight to a cooktop service center, while the cause sits in the terminal block and can be fixed at the customer's home. Our technicians tighten or replace the block, check the jumpers and measure the voltage with all zones running. A warm plug or a darkened socket after cooking is a sign of a poor contact that will eventually ruin the electronics.

Can a cooktop be plugged into a regular socket

A full-size cooktop is not plugged into a regular socket, because its power rating calls for a dedicated line with its own breaker. A standard household socket is designed for limited current, and a four-zone model with every zone on draws more than such a contact can carry for long. An overheated socket and plug melt, and voltage drops cause glitches in the terminal block and the board. For the cooktop, a separate copper cable of the right cross-section runs to the electrical panel, a breaker of a suitable rating is installed, and the appliance is connected directly through terminals or a power outlet. Narrow two-zone models sometimes come with a plug, but they also need a sound line without extension cords and splitters. Before buying a new model, check the cable cross-section and the breaker rating; it's simpler than replacing a burnt terminal block.

Glass, touch controls and the child lock

The top of the appliance, the glass and the touch controls, starts acting up after impacts, moisture and an accidental lock. Owners can clear some of these glitches themselves; the rest needs a technician.

Why the touch controls don't respond

  • Water on the buttons: spilled liquid registers as a touch, so the cooktop locks the controls or switches off for protection.
  • Grease and film: a dried layer on the glass stops your finger from passing the signal, so wipe the control area with a dry soft cloth.
  • Fabric and oven mitts: the touch panel reacts to the capacitance of a finger, so pressing through a mitt or glove doesn't count.
  • Moisture under the glass: after a sugary spill the touch panel traces corrode, and the buttons trigger on their own or stop responding.
  • Control board: if the touch controls don't come back after drying, we check the board and its ribbon cable, and pressing again won't help.

Child lock and protective shutoffs

A key or padlock symbol on the display means the child lock is on, and you release it by holding down the button with that symbol. The lock switches on by accident, when you wipe the glass or set a pot on the touch panel, and then the cooktop looks broken: the lights are on, but the zones won't start. The unlocking sequence differs between brands, so it's safer to check the manual for your model. A second kind of false fault is automatic shutoff: the safety timer turns a zone off if the power level hasn't changed for a long time, and overheat protection stops heating an empty pan. On induction, a zone also goes off when a pan is removed and not put back within the set time. If the heat cuts out by itself after a long run at one power level, it may be the safety timer, not a fault.

A crack in the glass-ceramic top

We replace cracked glass-ceramic, and an appliance with a crack must not be used. Moisture and grease get inside through the crack and reach the ribbons, coils and touch panel, and the glass can crack further when heated. The technician removes the old glass, sets the new one on heat-resistant sealant and moves the touch unit onto it if the unit is attached to the glass. The new glass is matched exactly to the model: the size, zone layout and markings must coincide, otherwise the touch controls and zones won't line up. The price of cooktop repair with glass replacement depends on the model and shape, so we quote it after free diagnostics. Until the technician arrives, switch the cooktop off at the breaker and don't put any cookware on the crack, even cold.

How our technician works at your home and in the service center

From the request to the post-repair check, the technician follows a clear sequence: a visit with diagnostics, work on site or in the service center, then testing and the warranty.

Arrival and free diagnostics

A Tech Service technician arrives within 60 minutes anywhere in the city and starts with free diagnostics. On site, the technician asks about the symptoms, checks the voltage at the socket and the panel, inspects the terminal block, and then finds the faulty component from the error code and measurements. The technician quotes the cost of the work after diagnostics, once the cause is clear. Our technicians have 4 to 20 years of experience, and we carry out cooktop repair in Almaty for every heating type: induction, Hi-Light glass-ceramic, gas and combination models. We are a direct provider: our own technician comes to you, not a random contractor working someone else's order. Clear access to the electrical panel and the underside of the countertop so the connection check goes faster.

Which jobs we do at home and which in the service center

JobWhere we do itWhat we check afterwards
Hi-Light burner replacementAt homeHeating at all levels
Induction coil replacementAt homePan detection and heating
Terminal block and cable replacementAt homeVoltage under load
Thermocouple and spark plug replacementAt homeFlame holding and spark
Glass-ceramic replacementAt home or in the service centerSealing and touch control operation
Control board repairIn the service centerAll zones and modes
Power module repairIn the service centerHeating under load

Warranty and the post-repair check

We give a 1-year warranty on labor and parts. Before leaving, the technician runs the repaired appliance in every mode: each zone at different power levels, the touch controls and the timer, and on a gas model, flame holding and ignition on every burner. Replacement parts are chosen for the specific model, so the warranty covers both them and the work done. The technician explains which component failed and why, which helps you avoid a repeat fault caused by cookware, overheating or the connection. You can pay in whatever way suits you, as we accept Kaspi QR, Kaspi Red, card, cash or bank transfer. For the first few days after the repair, cook on different zones and power levels, so any hidden fault shows up sooner.

Cooktop repair a quick guide

A short summary for the owner of a cooktop that has lost heat, shows an error on the display or keeps tripping the protection in the electrical panel: five points to keep in mind before calling a technician.

  • The symptom points to the component: on induction it is the coil, power module or board; on glass-ceramic, the ribbon, limiter and relays.
  • Check the cookware first: a magnet on the bottom of the pot separates unsuitable cookware from a real fault in the induction zone in a second.
  • Don't keep resetting the breaker: switching on into a short spreads the damage, so after the second trip the appliance is disconnected.
  • Gas needs attention: a flame that goes out is linked to the thermocouple and valve, and if you smell gas, shut the tap on the pipe at once.
  • A crack means replacing the glass: moisture reaches the electronics through it, so a cooktop with a crack is not switched on again.

24brands

Which cooktop brands we repair in Almaty

We match parts to the cooktop model. See the list of brands with their own pages below.

We also repairWe also repairTECH SERVICE09

Besides cooktop repair, we fix other equipment in Almaty

Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.

BlogBlogTECH SERVICE10

Worth reading before cooktop repair in Almaty

Leave a review

Choose a platform — the TECH SERVICE page will open.

2ГИС2GISGoogle MapsЯYandex Maps
Send a review with photos on WhatsApp