Original
Original seal
- Material
- rubber matching the factory original
- Profile
- exactly matches the mounting location
- Kit
- may include clamps
- Delivery time
- depends on the supplier's availability
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 746 00 26Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
Door seal replacement with a 1-year warranty on labor and parts. A technician arrives within 60 minutes anywhere in the city, and diagnostics are free.
Our own technicians4 to 20 years of experience




1 yearwarranty on labor and parts
60 minutestechnician arrival anywhere in the city
freediagnostics
The job has five steps: removing the old seal, cleaning and degreasing the seat, installing the new seal, checking tension and tightness, and a test run. The price is set after free diagnostics.
01
Step 1a few minutes
The technician carefully removes the spring ring and takes out the worn seal without damaging the door edge.
02
Step 2a few minutes
The seat is cleaned of buildup and detergent residue and degreased so the new seal fits tightly.
03
Step 3about fifteen minutes
The new seal is fitted onto the door edge with even tension around the entire perimeter.
04
Step 4a few minutes
The technician checks that the seal fits tightly against the glass and the body, with no gaps or misalignment.
05
Step 5a few minutes
A short wash without laundry confirms that water doesn't leak and the door closes tightly.
5
Five signs tell you the seal needs replacing. If water leaks from the front near the door rather than from below, check the seal first.
Cracks and tears
The seal surface shows cracks, cuts, or tears that let water escape.
Musty smell
A musty smell comes from the drum even when draining works, pointing to seal wear.
Dark buildup and mold
Dirt and black buildup collect in the seal folds, are hard to remove, and damage the rubber.
Squeak or pop
A strange squeak or pop is heard when closing the door, indicating wear on the seal profile.
Gap at the body
The drum is visible through a gap, or air passes through when the door is closed.
Place a napkin under the door and note exactly where water seeps from so you can describe the problem to the technician more accurately.
Describe the symptomsChoose a seal by material, profile, and whether clamps are included.
Original
or
Aftermarket
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1 visittime
from 4,500 ₸cost

BeforeAfterThe home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsExpert washing machine repair technician
experience8 yearsSenior washing machine repair technician
experience9 yearsWashing machine repair technician
We reply during working hours
Pick a convenient visit time and clear access to the machine in advance so the technician can start without delays.

Warranty question? Call us
+7 (778) 746 00 266 064 reviews of repairs at TECH SERVICE in total
Богдан С.Order No. 69617 · 14 July 2026
oursСимптом был очевидный: не отжимает. В techservice попал случайно — и остался. Сказать, что доволен — ничего не сказать.
Малик Т.Order No. ZK-2025/600 · 2 July 2025
oursБыло важно, чтобы сделали до выходных — гости, то-сё. Жалоба простая: не отжимает. Работает как раньше, придирок нет
Светлана Д.Order No. TS-2101-184 · 4 November 2021
oursДосымның кеңесімен келдім, өкінбедім. Жұмыс барысын көрсетіп отырды, жасырған жоқ. Жөндеуге кепілдік бар, сол сенімді.
Кристина Л.Order No. TS-9241 · 13 January 2021
oursИскал мастерскую поближе к дому, чтобы не мотаться с техникой через полгорода. Отдал мастеру: стирально-сушильная машина. Симптом был очевидный: не сушит. Ораз взялся за то, от чего другие отказались. Сначала сказали одно, потом уточнили, но в итоге всё совпало. Оплатил картой, чек дали. В списке работ — тэн. Не пожалел ни разу. Ребёнок уже проверил на прочность, держится
Мадина Т.Order No. ZK-4096 · 23 September 2020
oursЖалоба простая: ошибка на дисплее. Дима возился с этим дольше, чем планировал, но довёл до конца. Ребёнок уже проверил на прочность, держится
Владимир Н.Order No. ZK-5322 · 16 October 2019
oursЖалоба простая: течёт. Работает как раньше, придирок нет. Сделали и забыл про проблему.
Сауле Н.Order No. TS-1904-298 · 19 June 2019
oursЦена имела значение, но и гарантия тоже. Скажу прямо: ожидал худшего. Больше всего напрягало: ошибка на дисплее. Шум пропал, работает мягко
Андрей П.Order No. TS-1804-808 · 4 August 2018
oursДо этого обращался в другой сервис, там только развели руками. Больше всего напрягало: не отжимает. Ребята из techservice работают давно, это чувствуется. Второй месяц — полёт нормальный.
Виктор Ф.Order No. TS-6901 · 15 June 2017
oursПробовал найти мастера в своём районе, но все были заняты. Пользуюсь ежедневно, вопросов нет.
Ринат Х.Order No. TS-4373 · 18 March 2017
oursСмотрел, у кого есть запчасти на такую модель. Позвонил узнать про ремонт промышленной стиральной машины. С чем пришёл: вибрация. Включил, проверил, работает.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionIt's better not to run a wash with a torn seal: water will leak out, and dirt and lint get stuck in the tear. This speeds up wear and can flood your floor, so it's best to replace the seal first.
Gluing the seal with silicone or adhesive won't work: the rubber keeps flexing, and the patch quickly comes off. The sealant can't handle the load and doesn't provide a watertight seal, so the leak comes back.
The seal is matched by part number or model code: for Bosch it's the E-Nr on the sticker inside the door, for other brands it's the code on the rating plate. The same brand makes different series, and their seals aren't interchangeable, so the technician checks the number before installing.
Technically yes, but the seal sits on a spring clamp and is pressed tightly against the body, so without experience it's easy to tear it or install it crooked. If it's crooked, the door will start leaking water again, and the job will have to be redone.
Shut off the water supply, unplug the machine, and put down a cloth. If there's an emergency drain, carefully drain the water into a basin without opening the filter all the way. Then call a technician to take a look.
A worn seal makes the front area around the door wet, while a hose or pump leak shows up as water underneath the machine. If water collects on the floor near the front panel, the seal is often the cause, but a technician can tell for sure during an inspection.
Tech Service replaces the door seal on washing machines in Almaty—at your home or at the service center. The technician arrives within 60 minutes anywhere in the city, diagnostics are free, and we select the part by number or model code. We provide a 1-year warranty on labor and parts and you can pay via Kaspi QR, Kaspi Red (instalments), bank card, cash, or bank transfer for companies.
The door seal is a wear part that degrades over time from detergents and mechanical stress. Here's how to tell when it's time for a replacement and why a cosmetic fix won't work.
If black deposits have worked their way into the fold of the rubber and keep coming back with an odor after cleaning, it's time to replace the seal. Mold grows into microcracks in the rubber, so surface treatment only removes what's visible, not the cause. It's worth trying a mild cleaner and wiping the fold all the way around first—sometimes that works. But when dark spots are deep in the seal and the musty smell persists wash after wash, cleaning becomes an endless cycle. Replacing the washing machine door seal in that case solves the problem once and for all—new rubber without pores gives mold no place to take hold. Constant moisture in the fold speeds up wear: leaving the door ajar between washes makes deposits appear much less often and helps the rubber stay soft longer.
Torn or hardened rubber can't be restored with silicone or a patch—a new part is needed. Technicians often hear "can't you just glue it?"—and the short answer is no. Silicone sets on the surface, but the seal's edge compresses and expands with every cycle, so a patch comes off after just a few washes with a spin. Repairing a washing machine door seal with silicone doesn't make it watertight: pressurized water finds its way through microgaps, and the floor is wet again. Plus, moisture builds up under the patch—mold returns faster than before the repair. If the rubber is cracked or torn at the edge, the only reliable option is to install a new part matched to your machine model. At a typical 800–1600 rpm, the edge takes stress on every spin, so any half-measure won't last long.
Water on the floor doesn't always mean the door seal. Here's how to pinpoint the source by where the leak appears and what's safe to do before the technician arrives.
| Leak location | Likely cause |
|---|---|
| Front at the door, along the edge | Door seal |
| Under the door after spinning | Door seal or its fit |
| Underneath the body | Hoses, pump, tubing |
| Stream near the service flap | Drain filter or pump |
The door seal leaks at the front of the hatch, while the hoses, pump, and tubes let water out from under the body. So first, unplug the machine and drain the water through the emergency drain hose behind the service panel at the bottom front, placing a towel underneath. The technician will tell you how much a washing machine door seal replacement costs after a free diagnostic, once they inspect the assembly. The water in the drum may be hot — don't put your hands under the stream right away; let it drain onto a cloth. Don't unscrew the drain filter while the machine is running and don't take the pump apart: the impeller and pump housing should be checked by a technician with tools. Inspect the inlet hose where it connects to the body. Don't seal the gasket with silicone. Note at which stage of the cycle the moisture appeared. If water collects under the door after the spin cycle, the seal is usually to blame; if there's a puddle under the body, check the hoses, pump, and tubes.
We'll show you the steps a technician takes and explain when the seal can be replaced on-site and when it's better to bring the machine to the service center and what to prepare for that.
We come to your home anywhere in the city within 60 minutes, and if the client prefers, we replace the seal at the service center. A washing machine door seal replacement in Almaty is usually done right at the owner's place: the technician needs access to the hatch. This format works well for LG, Samsung, Bosch, Indesit, and Electrolux — on most brands the part can be removed without taking out the drum. You can replace the seal on-site if there's free access to the hatch. On-site, the work is done right at the hatch. If the machine is built into the kitchen, clear access to the hatch beforehand. At the service center, the seal is replaced if space at home is tight or the appliance is in a niche. This option is chosen when the hatch is hard to reach and access to the seal's mounting seat is needed.
The door seal fits not by brand but by the specific machine. Below we explain where to find the part number and model code and why a visual match of the rubber isn't enough.
We select the seal by part number or model code, and for Bosch we check the E-Nr on the rating plate inside the hatch. The marking is usually stamped on the rubber itself or listed in the documentation, and the appliance code is on the rating plate: for LG and Samsung it's a sticker on the back or under the hatch, for Indesit and Electrolux it's a plate on the body. The technician cross-checks the data with the catalog and picks the part for the specific series: Bosch's older Maxx, Logixx, Classixx lines and the current Serie 2/4/6/8 use different seals. The model code and part number are more reliable than a visual match of the rubber because similar machines have different mounting dimensions. Take a photo of the rating plate before the technician arrives — it speeds up part selection.
| Brand | What we check | How we select |
|---|---|---|
| Bosch | Series and E-Nr | By the rating plate inside the hatch |
| LG | Model code | By the sticker on the body |
| Samsung | Model code | By the sticker on the body |
| Indesit, Electrolux | Part number | By the marking on the seal |
Let's break down what the warranty covers, how payment works, and why dealing directly with the technician saves the machine owner from unnecessary links in the chain.
We provide a 1-year warranty on labor and parts. The term is the same for the seal and for its installation—whether it's a front-loading machine or a top-loading model. That's why it's important to select the seal by part number or model code, not by eye: for Bosch, the E-Nr is on the sticker inside the door; for other brands, it's on the rating plate on the body. The cost of replacing a washing machine seal depends on the model and the part itself, and the technician gives you the exact price after free diagnostics. This is the first thing owners ask about—and rightly so: the seal is in constant contact with water and the drum, so it's crucial to match the part precisely to the model.
Here's what a machine owner should remember: when the part really needs replacing, how to tell its leak from other causes, and what to do before the technician arrives.
If you ask, the technician will check other parts during the same visit.
Refrigerator Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
Washing machine error codes are self-diagnostic codes that point to a specific component: drain, water fill, heating, motor, or door lock.
29 January 2026 · 13 minutes read
If your washing machine won't spin, it's usually an unbalanced load, a clogged drain filter or hose, and less often the pump, belt…
19 January 2026 · 12 minutes read
If your washing machine isn't heating water, the heating element or temperature sensor is usually to blame, less often the control board or wiring.
25 December 2025 · 12 minutes read
If your washing machine won't turn on, first check the outlet, extension cord, and the circuit breaker in your panel, then the plug and power cord.
24 November 2025 · 13 minutes read