Open until 19:00+7 (775) 030 02 94Call a technician
Tech Service technician next to a heater

Heater Repair in Almaty

A technician arrives within 60 minutes anywhere in the city. Free diagnostics.

  • 1-year warranty
  • Technicians with 4 to 20 years of experience
  • You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies

Our own technicians4 to 20 years of experience

Ruslan Ts.Damir M.Dilmurat S.Dima

Repair prices

  • Diagnostics0 ₸
  • Power cable replacementfrom2 000 ₸
  • Dust cleaningfrom2 000 ₸
  • Switch replacementfrom3 000 ₸
  • Fuse replacementfrom3 000 ₸
All prices
2ГИСЯours4,97 898 reviews
2GIS · Google · Yandex · order database
Common faultsCommon faultsTECH SERVICE02

Common heater faults in Almaty

From the symptom, an owner can often guess which part of the heater is at fault.

PricesPricesTECH SERVICE03

How much heater repair costs in Almaty

The cost depends on the fault and the heater model.

Power cable replacementparts not included

1–2 hours

from2 000 ₸

Dust cleaningexact price — after the free diagnostics

1–2 hours

from2 000 ₸

Switch replacementparts not included

1–3 hours

from3 000 ₸

Fuse replacementparts not included

1–2 hours

from3 000 ₸

Wiring repairexact price — after the free diagnostics

1–3 hours

from3 500 ₸

Before and afterBefore and afterTECH SERVICE04

Before and after heater repair in Almaty

Burned-out heating element

1–2 hourstime

from 4,000 ₸cost

Problem
The heater stopped heating; only the fan worked. The heating element was blackened and ruptured, the insulation was melted, and there were signs of scorching on the ceramic holders.
What we did
The technician performed free diagnostics, confirmed the heating element was broken, and replaced the heating element. He removed carbon deposits from the holders, reassembled the housing, and tested the heater in all modes.
Result
The heater again heats the air evenly, and the fan works properly. 1-year warranty on labor and parts.
I want the same
Heater: burned-out heating element — after repairBeforeAfter
01 / 03
All repairs
TECH SERVICE mobile technician with a tool case

How heater repair works at your home in Almaty

Five steps from your request to the final check.

  1. Requestright away

    Leave a request for heater repair.

  2. Technician visitwithin 60 minutes

    A technician arrives within 60 minutes anywhere in the city.

  3. Diagnosticsfree

    The technician checks the components one by one and shows the owner the fault.

  4. Approvalbefore repair

    The technician explains the scope of work and the cost, and you approve them before the repair starts.

  5. Final checkafter repair

    After reassembly, the technician switches the heater on and checks heating and thermostat operation in different modes.

Leave a request
TechniciansTechniciansTECH SERVICE05

Our home appliance repair technicians in Almaty

The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

  • 8 technicians in Almaty
  • 8–12 years of experience in the department
  • Article author Ruslan Ts., 9 years of experience
Mobile technician fixing a washing machine at the customer's home
Field technician at a customer’s home

The department has 8 specializations — they are listed on the technicians' cards.

01 / 08
Ruslan Ts., washing machine and refrigerator repair technicianexperience9 years

Ruslan Ts.

Washing machine and refrigerator repair technician

Damir M., general household appliance repair technicianexperience12 years

Damir M.

General household appliance repair technician

Dilmurat S., field technician for washing machine and refrigerator repairexperience10 years

Dilmurat S.

Field technician for washing machine and refrigerator repair

Dima, expert washing machine repair technicianexperience8 years

Dima

Expert washing machine repair technician

Nikita M., field refrigerator repair technicianexperience8 years

Nikita M.

Field refrigerator repair technician

Oraz, senior washing machine repair technicianexperience8 years

Oraz

Senior washing machine repair technician

Radik T., dishwasher repair technicianexperience11 years

Radik T.

Dishwasher repair technician

Rustem T., washing machine repair technicianexperience9 years

Rustem T.

Washing machine repair technician

We reply during working hours

Book heater repair in Almaty

Describe the symptom: not heating, turning off or sparking. The technician will bring the right parts.

TECH SERVICE administrator replying to a customer's WhatsApp message

Warranty question? Call us

+7 (775) 030 02 94
Customer reviewsReviewsTECH SERVICE06

Reviews of heater repair in Almaty

Малик Т.Order No. 34646 · 16 October 2026

ours

Позвонил знакомому, он раньше работал в сервисе, посоветовал этих. Больше всего напрягало: не греет. Проверил дома — всё на месте, ничего не забыли.

Repair: heater repair in

Талгат С.Order No. TS-2602-132 · 21 June 2026

ours

Больше всего напрягало: не дует горячим. Отдельно скажу про мастера: Никита М — спокойный, без лишней суеты. Проверили на всех режимах, всё чётко.

Repair: heater repair in

Азамат Е.Order No. TS-2610-332 · 10 June 2026

ours

Искал мастерскую поближе к дому, чтобы не мотаться с техникой через полгорода. С чем пришёл: не греет. Внешне как новый, если не считать мелкой царапины.

Repair: heater repair in

Алия Ш.Order No. TS-2511-983 · 27 December 2025

ours

Цена имела значение, но и гарантия тоже. Приняли без очереди, оформили за пять минут. Шум пропал, работает мягко.

Repair: heater repair in

Светлана Д.Order No. ZK-2025/889 · 29 October 2025

ours

Больше всего напрягало: не дует горячим. Дамир М не стал навязывать дорогую запчасть, поставил нормальную. Починили и дали гарантию на месяц.

Repair: heater repair in

Ержан А.Order No. ZK-3986 · 14 September 2025

ours

Выбирал по отзывам в 2ГИС, времени на эксперименты не было. Симптом был очевидный: щелкает. Починили и дали гарантию на месяц.

Repair: heater repair in

Аяна Е.Order No. 2025-5573 · 28 August 2025

ours

Отдельно скажу про мастера: Дамир М — спокойный, без лишней суеты. Под замену пошло: плата. Починили и дали гарантию на месяц

Repair: heater repair in

Динара М.Order No. ZK-2806 · 27 July 2025

ours

Нужен был счёт и чек, у нас техника на балансе организации. Утром столкнулся с тем, что щелкает. Договорились на утро, к девяти уже был свободный мастер. Вернули в тот же день, всё функционирует.

Repair: heater repair in

Жанар Т.Order No. 782774 · 21 October 2024

ours

Техника на гарантии уже не была, так что выбор был свободный. Повод для визита: течёт масло. В тех сервис привёл знакомый, у него тут чинили ноут. Пользуюсь ежедневно, вопросов нет.

Repair: heater repair in

Сабина Г.Order No. ZK-2024/634 · 15 September 2024

ours

Пробовал найти мастера в своём районе, но все были заняты. Проблема — шумит. Пользуюсь ежедневно, вопросов нет.

Repair: heater repair in
Questions and answersQuestionsTECH SERVICE07

Questions about heater repair in Almaty

Didn’t find the answer? Message us on WhatsApp.

Ask a question
Why does an oil-filled radiator click but not heat up?

The clicking usually comes from the thermostat, which is tripping but not sending power to the heating element, or the heating element itself has burned out. It depends on the model: the technician will test the heating element and check the thermostat contacts after free diagnostics.

The convector only heats at maximum, but turns off in other modes — what's the cause?

Most often the thermostat or temperature sensor is to blame, misreading the heat and breaking the circuit. Less commonly it's the control board, so the technician checks the sensors first, then the electronics.

The fan heater runs but blows cold air — is it the coil or the ceramic element?

It depends on the model: both the coil and the ceramic heater can burn out or lose contact while the fan keeps running. The technician will test the heating element and check the power circuit leading to it.

Can the heating tube in an infrared heater be replaced if it no longer glows?

Yes, the tube or emitter is usually replaced if the heater itself has burned out and the wiring and protection are intact. The technician will pinpoint the exact component after diagnostics, since emitter design varies by model.

Is it dangerous to keep using a heater if it crackles when heating up?

Yes, it's better to turn the device off: crackling can mean poor contact, sparking, or damaged insulation, which is a fire risk. The technician will check the terminals, cable, and heating unit to find the source of the sound.

Do you repair heaters with electronic controls if the remote and display don't respond?

Yes, we repair heaters with electronics: we check the control board, the remote receiver, and the display contacts. Often the cause is the board itself or the ribbon cable, and the technician will tell you exactly what failed after free diagnostics.

Repair guideArticleTECH SERVICE08

Heater Repair in Almaty by Tech Service Technicians

Ruslan Ts., washing machine and refrigerator repair technician

Author: Ruslan Ts.,Washing machine and refrigerator repair technician

Published
Updated

Heater repair in Almaty is handled by our own technicians: a specialist arrives within 60 minutes anywhere in the city, and diagnostics is free. We fix oil-filled radiators, convectors, fan heaters and infrared models at your home or at our service. Our technicians have 4 to 20 years of experience, and we give a 1-year warranty on labor and parts.

What breaks in an oil-filled radiator

The oil-filled radiator is the most common home heater, and it fails in three ways: it stops heating, it clicks and shuts off, or it loses oil. We go through each case part by part.

The radiator turns on but stays cold

If the indicator light is on but the body stays cold, we first check the heating element, the thermostat and the power switch. The heating element sits at the bottom of the radiator and heats the oil, which then passes the warmth to the fins; if the wire inside the tube breaks, a multimeter shows infinite resistance. A thermostat with an adjustment knob can be mechanically intact while its contacts burn and stop closing the circuit. The power level switch wears out in a similar way: in one position the heater works, in another it stays silent. Heater repair in Almaty starts with free diagnostics at your home — a technician with 4 to 20 years of experience tests the circuit from the plug to the element and names the cause before any work begins. Keep in mind that the power light is often wired before the thermostat, so a glowing light does not yet mean current is reaching the heating element.

Clicking and frequent shutoffs

A click as the radiator heats up and cools down is normal bimetallic thermostat operation, but shutting off a couple of minutes after start points to a worn thermostat, overheating from poor placement, or a tripped thermal fuse. The bimetallic strip bends with heat and opens the contacts at the set temperature; over time it loses its spring, and the heater switches off before the room warms up. The thermal fuse cuts power when the body overheats, and on some models you then have to wait for it to cool down. Overheating happens when the heater stands right against a wall, behind a heavy curtain, or under laundry left to dry: hot air cannot rise away, and the protection trips too early. Before calling a technician, move the radiator away from the wall and take everything off it — shutoffs caused by overheating are not a fault in themselves.

Oil leaks and when repair stops making sense

An oil leak from the body is a serious defect, and we say it plainly: such a radiator is usually not repaired. The body of an oil-filled heater is factory-welded and sealed, holding a carefully measured amount of mineral oil with an air gap for expansion when hot. Soldering a crack on site restores neither the seal nor the correct oil level, and a heater short of oil overheats its element and becomes a fire hazard. A Tech Service technician will inspect the seams and the element mounting, make sure the drips really are oil, and tell you whether repair makes sense; diagnostics is free. If oil is still dripping, unplug the heater at once and do not switch it on until it has been inspected — on a hot body, oil stains smoke and leave a lasting smell.

Convector faults in mechanical and electronic models

Convectors come with either a mechanical or an electronic thermostat, and the set of typical faults depends on it. Below we cover both control types and give a table of common symptoms.

The convector heats only at maximum power

When a convector works only on the top setting, we check the power switch and the sections of the heating element: quite often one section has burned out. In many convectors the heater is made of two parts, and the switch connects them one at a time or together; if the part responsible for the low setting fails, the unit heats only at full power. The cause can also be the switch itself — a burned contact fails to connect the right section, so in one position the body stays cold. The technician tests each section with a multimeter, inspects the terminals for scorching and tightens loose screw connections: an overheated terminal gives itself away through darkened plastic on the terminal block. A dead low setting is no reason to replace the whole element — the switch and contacts are checked first, because replacing them is simpler and gets the unit working again sooner.

Display, remote and control board

We diagnose an electronic convector with a blank display step by step: board power supply, temperature sensor, heating relay, buttons and remote. The power supply on the board steps down mains voltage for the electronics, and when it fails the unit stays completely silent even though the heating element is fine. The temperature sensor (usually a thermistor) reports air temperature to the board; if it is broken or has shifted out of place, the convector cannot hold the set mode. The relay on the board switches the heater and can stick over time — then the unit heats nonstop and ignores the settings. A Tech Service technician checks the board section by section and explains which makes more sense: replacing a single part or the whole board. Before calling, put new batteries in the remote and switch the convector on with the button on the body — that shows right away whether the remote or the electronics is to blame.

Convector symptoms and the likely part

SymptomWhere the check startsPossible repair
Won't turn on, display darkCord, plug, board power supplyCord replacement, board repair
Heats nonstopRelay, thermostatRelay or thermostat replacement
Cold on the low settingHeater section, switchSection or switch replacement
Shuts off after a few minutesThermostat, thermal fusePlacement check, protection replacement
Can't hold the set temperatureTemperature sensorSensor replacement

Why a fan heater blows cold air

A fan heater has two main parts — the heating element and the motor with its fan blade. Cold airflow, noise and sudden stops point to different faults, so we look at each one separately.

The fan spins but the air stays cold

Cold air from a running motor almost always means a broken coil, a failed ceramic element, or tripped thermal protection. The nichrome coil is strung on insulators right behind the grille, and the break is often visible to the eye — a gap and a darkened section of wire. A ceramic element looks intact from the outside, so it can only be checked with a meter by measuring resistance across its terminals. The third suspect is the thermal fuse next to the element: if it is open, the motor runs but there is no heat. To fix a heater of this type, we fit a new element of the right power rating and always find out why the protection tripped. Twisting a burned coil back together is a bad idea: resistance at the joint is higher, so that spot overheats, burns through again and melts the plastic nearby.

Noise, humming and a stalled motor

Humming, rattling and a slow-starting fan blade point to dust and dried-out lubricant in the motor bearings, or to a warped blade. A fan heater pulls a lot of air through itself, and with it come dust, pet hair and carpet fluff. Building up on the shaft, the dirt slows the motor, while a blade bent by heat catches the housing and makes a rhythmic knock. In compact models the motor is usually replaced as a unit; in larger ones the bushings can sometimes be cleaned and lubricated. A stalled motor is dangerous not because of the noise but because of overheating: the element keeps working with no airflow, the housing gets very hot, and the protection trips. That is why a heater that hums but does not blow should be switched off at once, without waiting for a burning smell, and not used again until it has been checked.

How a coil element differs from a ceramic one

  • Coil element: an open nichrome coil heats up fast and gives warmth at once, but it burns settled dust and needs replacing if it breaks.
  • Ceramic element: a finned plate heats more evenly, smells less of dust and limits its own temperature when airflow is weak.
  • Sign of a failed ceramic element: the heater blows barely warm air on every setting, even though the motor and switch work fine.
  • What we repair: both element types, the motor, mode switch, thermostat and protection, choosing parts by power rating and housing size.
  • Looking after the heater: blow the dust out of the grille once a season — a clean element of any type overheats less and lasts longer.

Infrared heaters and their heating elements

An infrared heater warms objects and people rather than the air, using radiation from a tube or a panel. What breaks and what can be replaced depends on the type of emitter.

The tube does not glow or heat

If the tube of an infrared heater does not glow, we check that it is intact, test the contacts in the holders and the switch, and then pick a new emitter by length, mounting type and power rating. The tube is the most fragile part of such a heater: inside the quartz bulb is a filament that breaks from impacts, falls and sudden temperature changes. Sometimes the tube is fine but the contacts at its ends have oxidized, and cleaning the holders is enough. In models with several tubes and a power level switch, we test each emitter separately so as not to miss a second one that is starting to darken. A technician arrives within 60 minutes anywhere in the city, and diagnostics is free. Never touch the bulb of a new tube with bare fingers — skin oil on the quartz leaves a mark when heated and shortens the life of the emitter.

Types of emitters and how they fail

Emitter typeSign of failureWhat is done
Quartz tubeDoes not glow after an impactTube replacement by length and power
Halogen tubeDoes not glow, deposit on the bulbTube replacement, holder check
Carbon tubeDoes not glow, cracked bulbReplacement with the same tube type
Film panelNo heat with a working regulatorContact check, panel replacement
Ceramic emitterCold, open circuitEmitter replacement

Wall and ceiling panels

We diagnose a wall-mounted infrared panel on site without taking it down unless needed: we check the supply voltage, the thermostat and the connection terminals. Many panels run through a separate wall thermostat, and its failure is easy to mistake for a fault in the panel itself — the thermostat simply does not supply power. Ceiling models are checked from a ladder: we inspect the mounting, the cable and any signs of overheating on the junction box. If the panel does not heat while the thermostat works, the technician measures the resistance of the heating layer; a break inside the film usually cannot be repaired, and the panel is replaced as a whole. A Tech Service technician checks the thermostat and wiring together with the panel, so the new part does not fail for the same reason. Before calling, check whether the breaker in the panel box is off and whether the thermostat is set to minimum — these are the simplest reasons for silence.

Why the protection trips and you smell burning

Almost every modern heater has protective parts. They switch the unit off when something goes wrong, and when they trip it does not always mean the heating element itself is broken.

The thermal fuse and overheating

A thermal fuse opens the circuit when the housing overheats: a one-time fuse has to be replaced after it trips, while a self-resetting one closes again once it cools down. It sits next to the element and reacts to temperature rather than current, so it trips when the heater is covered, clogged with dust or pushed right up against furniture. If the protection shuts the heater off again and again, the cause is usually in another part — a stalled motor, a stuck thermostat, a blocked grille. Replacing only the tripped protection without finding the cause buys a short break until the next shutoff, so the technician first checks the motor, the thermostat and how clean the grille is, and only then fits a new part. A jumper wire in place of a thermal fuse removes the last barrier against fire, which is why a tripped fuse is replaced only with an equivalent that has the same temperature threshold and rated current.

The tip-over switch and random shutoffs

If the heater switches off at a light nudge, we check the tip-over switch: the contact inside wears out and opens even when the unit has not fallen. These switches are fitted to floor-standing models — fan heaters, convectors on feet, infrared heaters; it looks like a small button on the bottom of the housing or a ball switch inside. When the heater tilts, the contact opens and power to the element is cut, but in a worn switch the contact chatters, and the indicator flickers with every step nearby. The technician tests the switch in different positions and replaces it with a working one; we will not disable the protection for convenience, because it prevents a fire if the heater falls onto a rug. Before calling a technician, put the heater on a flat, hard surface: on a soft, deep pile the switch can trip even on a working unit.

When to switch the heater off immediately

  • Smell of burning plastic: a lasting smell after the first minutes of use means the wiring is overheating, so the heater is unplugged at once.
  • Hot plug: a plug and outlet that are uncomfortably hot to touch point to a burned contact that will gradually melt the plastic.
  • Sparks and crackling: flashes inside the housing and clicks that do not sound like the thermostat mean damaged insulation and a fire risk.
  • Damaged cord: kinks, melted insulation and bare wires near the base are a reason for replacement, and we replace the cord together with the plug.
  • Dust after summer: a faint dusty smell the first time you switch on in the season fades within minutes, while a burning smell stays — that is the difference.

How heater repair works with us

From your request to the check after repair there are a few clear steps. Here is what the technician does at each stage, when repair is worth it and what the warranty covers.

Steps from request to final check

StageWhat happensGood to know
RequestYou name the heater type and symptomThe technician knows in advance what to check
VisitThe technician arrives within 60 minutesAnywhere in the city
DiagnosticsCircuit testing and inspection of partsDiagnostics is free
ApprovalThe technician names the cause and costThe decision stays with the owner
RepairPart replacement at home or at our serviceThe format depends on the fault
Final checkTest run and protection check1-year warranty on labor and parts

Is it worth fixing a heater

Repair is worth it when a replaceable part has failed — the thermostat, switch, cord, motor, sensor or heating element — and the housing is intact and undamaged. Such parts fit into their original places and fully restore the heater. With us, heater repair in Almaty always starts with free diagnostics, so the owner loses nothing even if the repair turns out not to be worth it. We consider repair not worthwhile when oil leaks from the body, the plastic housing has melted, the board has burned out with no components available, or several parts have failed at once. A technician with 4 to 20 years of experience weighs the amount of work against the condition of the heater and tells you straight whether it is worth taking on. Keep the box or the label with the model and power rating — they make it easier to find the right part and to judge the repair sooner.

Warranty and payment

For every repair we give a 1-year warranty on labor and parts, and you can pay via Kaspi QR, Kaspi Red, bank card, cash or bank transfer for companies. Tech Service is a direct provider: the technician who comes to you works at our service and does not pass the job on to middlemen. That means the same service whose specialist tested the circuit, replaced the part and ran the final test is responsible for the result. If the heater shuts off again or stops heating after the repair, you contact the same place that fixed it and do not have to explain the history of the fault to someone new. The technician names the cost after free diagnostics and before any work starts, so you decide on the repair already knowing the cause. Write down the heater model and which part was replaced — if a similar symptom comes back, it will be easier for the technician to compare it with the earlier fault.

Heater repair choices for colder months

Different types of heaters break in different ways, but the repair logic is the same: first the cause, then the part. Below are short takeaways from the whole guide.

  • Cause first: a cold body, clicking and shutoffs point to a specific part, and replacing a part without finding the cause does not solve the problem.
  • Leaking oil-filled radiator: a sealed oil-filled body cannot be restored on site, so replacing such a heater with a new one is safer.
  • Fan heater and convector: the coil, ceramic element, switch and motor are replaced as units, while electronics are checked step by step starting from the power supply.
  • Protection is not the enemy: the thermal fuse and tip-over switch prevent fires, so they are replaced with equivalents, never bypassed with a jumper.
  • Danger signs: a burning smell, a hot plug and sparks mean the heater must be unplugged at once and left until it is diagnosed.

27brands

Which heater brands we repair in Almaty

We match parts to your heater model. Check the brand with the technician.

We also repairWe also repairTECH SERVICE09

Besides heater repair, we fix other equipment in Almaty

Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.

BlogBlogTECH SERVICE10

Worth reading before heater repair in Almaty

Leave a review

Choose a platform — the TECH SERVICE page will open.

2ГИС2GISGoogle MapsЯYandex Maps
Send a review with photos on WhatsApp