Open until 19:00+7 (778) 021 13 16Call a technician
Tech Service technician next to a gas boiler

Gas Boiler Repair in Almaty

A technician arrives within 60 minutes anywhere in the city. Diagnostics are free, and our technicians have 4 to 20 years of experience.

  • 1-year warranty on labor and parts
  • Arrival within 60 minutes anywhere in the city
  • Diagnostics free of charge

Our own technicians4 to 20 years of experience

Ruslan Ts.Damir M.Dilmurat S.Dima

Repair prices

  • Diagnostics0 ₸
  • Fan replacementfrom5 500 ₸
  • Temperature sensor replacementfrom6 000 ₸
  • Control board replacementfrom6 000 ₸
  • Gas valve replacementfrom7 000 ₸
All prices
2ГИСЯours4,97 898 reviews
2GIS · Google · Yandex · order database
Common faultsCommon faultsTECH SERVICE02

Common gas boiler faults in Almaty

The symptoms people most often call a technician about. The exact cause is confirmed during free diagnostics.

PricesPricesTECH SERVICE03

How much gas boiler repair costs in Almaty

The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.

Fan replacementparts not included

1–2 hours

from5 500 ₸

Temperature sensor replacementparts not included

1–2 hours

from6 000 ₸

Control board replacementparts not included

1–2 days

from6 000 ₸

Gas valve replacementparts not included

1–2 hours

from7 000 ₸

Three-way valve repairparts not included

1–2 hours

from7 500 ₸

Before and afterBefore and afterTECH SERVICE04

Before and after gas boiler repair in Almaty

Hot water barely warm, radiators heating

1 visittime

from 7 500 ₸cost

Problem
Hot water from the tap was barely warm, while the radiators were heating.
What we did
The technician opened the lower compartment of the boiler and found that the servo drive of the three-way valve was not switching the seized stem; he replaced the servo drive, worked the stem loose, and checked the switching.
Result
The boiler switches between water heating and space heating again, and the hot water comes out at normal temperature.
I want the same
Baxi gas boiler: hot water barely warm, radiators heating — after repairBeforeAfter
01 / 04
All repairs
TECH SERVICE mobile technician with a tool case

How gas boiler repair works at your home in Almaty

From request to final check in five steps. Diagnostics are free.

  1. Requeston the day you call

    Describe the symptom and the boiler model so the technician brings the right tools.

  2. Technician visitwithin 60 minutes

    The technician comes to any part of the city within an hour of your request.

  3. Diagnosticsfree

    Gas and water pressure check, error code analysis, inspection of components.

  4. Agreeing on the workbefore the repair

    A list of work by component: burner cleaning, gasket replacement, heat exchanger flushing.

  5. Post-repair checkafter the work

    Checking the joints for leaks and the combustion settings after reassembly.

Leave a request
TechniciansTechniciansTECH SERVICE05

Our home appliance repair technicians in Almaty

The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

  • 8 technicians in Almaty
  • 8–12 years of experience in the department
  • Article author Ruslan Ts., 9 years of experience
Technician repairing a gas boiler at a customer’s home
Field technician at a customer’s home

The department has 8 specializations — they are listed on the technicians' cards.

01 / 08
Ruslan Ts., washing machine and refrigerator repair technicianexperience9 years

Ruslan Ts.

Washing machine and refrigerator repair technician

Damir M., general household appliance repair technicianexperience12 years

Damir M.

General household appliance repair technician

Dilmurat S., field technician for washing machine and refrigerator repairexperience10 years

Dilmurat S.

Field technician for washing machine and refrigerator repair

Dima, expert washing machine repair technicianexperience8 years

Dima

Expert washing machine repair technician

Nikita M., field refrigerator repair technicianexperience8 years

Nikita M.

Field refrigerator repair technician

Oraz, senior washing machine repair technicianexperience8 years

Oraz

Senior washing machine repair technician

Radik T., dishwasher repair technicianexperience11 years

Radik T.

Dishwasher repair technician

Rustem T., washing machine repair technicianexperience9 years

Rustem T.

Washing machine repair technician

We reply during working hours

Book gas boiler repair in Almaty

Tell us the boiler model, the symptom and the error code on the display, and the technician will bring the right part and tools. Our technicians have 4 to 20 years of experience.

TECH SERVICE administrator replying to a customer's WhatsApp message

Warranty question? Call us

+7 (778) 021 13 16
Customer reviewsReviewsTECH SERVICE06

Reviews of gas boiler repair in Almaty

Айнур М.Order No. TS-2735 · 8 July 2026

ours

Было подозрение, что дело в плате, хотелось услышать второе мнение. Второй месяц — полёт нормальный.

Repair: gas boiler repair in

Гаухар Н.Order No. TS-2805 · 23 April 2026

ours

Дамир М принял, посмотрел и сразу сказал, что делать. Сказали 9 500, а потом ещё и скидку сделали. Сделали и забыл про проблему.

Repair: gas boiler repair in

Богдан С.Order No. 938445 · 24 March 2026

ours

Друг посоветовал, у него похожая история была. Нужен был ремонт газовой колонки — обратился сюда. Проблема — не зажигается. Поставили новую деталь: мембрана. По цене не скажу, что дёшево, но справедливо. Заявку приняли по телефону, перезвонили через десять минут. Вернули в тот же день, всё функционирует.

Repair: gas boiler repair in

Куаныш Б.Order No. ZK-6834 · 16 December 2025

ours

Было важно, чтобы сделали до выходных — гости, то-сё. С чем пришёл: не греет воду. Починили и дали гарантию на месяц.

Repair: gas boiler repair in

Эльмира Т.Order No. TS-3700 · 31 October 2025

ours

Симптом был очевидный: не зажигаеться. Проверили при мне, показали, что всё держит.

Repair: gas boiler repair in

Александра Н.Order No. ZK-2025/532 · 2 September 2025

ours

Құрылғы ескі болғандықтан, бөлшек табыла ма деп қорықтым. Күтуге уақытым жоқ еді, сол күні алып кеттім)

Repair: gas boiler repair in

Елена К.Order No. TS-8372 · 9 March 2025

ours

Повод для визита: не зажигается. Дамир М возился с этим дольше, чем планировал, но довёл до конца. Починили и дали гарантию на месяц.

Repair: gas boiler repair in

Ольга М.Order No. 2024-2927 · 9 September 2024

ours

Основная жалоба — не греет воду. Никита М помог выбрать, без навязывания. Сказать, что доволен — ничего не сказать

Repair: gas boiler repair in

Айгуль К.Order No. TS-3515 · 6 September 2024

ours

Пробовал найти мастера в своём районе, но все были заняты. Сдал в ремонт: газовая колонка. Повод для визита: не зажигается. Нагрев в норме, посторонних звуков нет.

Repair: gas boiler repair in

Аида Т.Order No. 2024-7770 · 28 March 2024

ours

Поломка застала перед командировкой, тянуть было нельзя. Симптом был очевидный: течёт. Проверили на всех режимах, всё чётко.

Repair: gas boiler repair in
Questions and answersQuestionsTECH SERVICE07

Questions about gas boiler repair in Almaty

Didn’t find the answer? Message us on WhatsApp.

Ask a question
Which brands make good gas boilers?

It's worth choosing brands that have service and common spare parts available in Almaty, so repairs don't drag on. A well-known brand alone doesn't guarantee reliability; parts availability matters more. We service equipment from various manufacturers, depending on the model.

What is the service life of a gas boiler in a private home?

The stated lifespan of a wall-mounted boiler is usually shorter than that of a floor-standing one, but much depends on the model and water quality. Regular maintenance and timely repairs noticeably extend the unit's life.

How do you know when it's time to replace a gas boiler?

It's worth replacing when breakdowns come one after another and repairing components no longer pays off. Warning signs include constant errors, heat exchanger leaks, and loss of power. A technician during diagnostics will tell you whether it's still worth fixing or easier to replace.

Can I reset an error on the boiler myself, or is it better to call a technician right away?

A one-time error can be reset with a button, but if it comes back, the issue is in a component, not a glitch. Repeated resets in a row won't help and can be dangerous. It's wiser to call a technician to find the cause.

Why does the boiler try to ignite, click, and then lock out?

Clicking without ignition usually means gas isn't coming in or the spark is weak; sometimes the flame sensor is to blame. It depends on the model: a clogged burner can also be the cause. A technician will check the ignition and gas valve on site.

Can a gas boiler be repaired at home, or does it get taken to a service center?

Most breakdowns are fixed at home: ignition, sensors, pump, valve, cleaning. It's rarely taken to a service center, only when the control board or a complex component needs repair. A technician arrives within 60 minutes in the city and decides on the spot, depending on the model.

Repair guideArticleTECH SERVICE08

Gas boiler repair in Almaty by Tech Service technicians with a warranty

Author: TECH SERVICE editorial team

Published
Updated

Tech Service repairs gas boilers in Almaty at your home or in our service center: our own technician with 4 to 20 years of experience arrives within 60 minutes anywhere in the city, runs free diagnostics and finds the faulty component. We give a 1-year warranty on labor and parts, accept payment via Kaspi QR, Kaspi Red, card, cash, or bank transfer for companies and quote the cost after the inspection.

Gas boiler repair starts with finding the faulty component

Every boiler failure comes down to one of four groups of components: combustion, flue gas removal, hydraulics or electronics. Here is where the search starts and why the code on the display is only a hint.

Why the boiler clicks but won't light

When the boiler clicks its electrode but no flame appears, we check the whole ignition chain: spark strength, gas valve opening and the ionization signal that tells the board a flame is present. Our gas boiler repair in Almaty starts with measurements, not with swapping the first suspicious part. The spark can arc to the casing because of a cracked electrode insulator, the valve may fail to open because of a broken coil, and the ionization signal can disappear because of soot on the probe or poor grounding. All of these faults look the same: several attempts to light the burner, then a lockout with an error. A technician with 4 to 20 years of experience tells them apart by multimeter readings during diagnostics, which are free with us. After a series of failed attempts, don't keep pressing reset — unburned gas builds up in the chamber, and the next ignition happens with a bang.

Draft, fan and pressure switch

In a boiler with a sealed combustion chamber, the burner will not light until the pressure switch confirms that the fan has created suction and flue gases are leaving through the coaxial pipe. The pressure switch is a diaphragm sensor with small tubes, and if one of them is blocked with condensate or cracked, the board sees no draft even when the fan is fine. Over time the fan itself starts to hum and lose speed as the bearing grease dries out and the impeller collects dust. An experienced gas boiler repair technician first listens to the fan and blows out the sensor tubes, and only then decides whether the unit needs replacing. If the fan does not spin at all, the power supply from the board and the motor winding are checked, because the cause may lie in the electronics. In winter the tip of the coaxial flue on the facade gets covered with frost and ice, so draft errors appear precisely on freezing days: before replacing the fan, check the pipe from outside.

Which component we check for each symptom

SymptomComponentWhat we check
Clicking with no flameIgnition electrode, gas valveSpark, valve coil
Flame goes out within secondsIonization electrodeSoot, grounding, signal
Draft errorPressure switch, fanSensor tubes, fan speed
Pressure below normalExpansion tank, jointsAir in the tank, leak points
Radiators stay coldCirculation pumpRotor movement, air
Random shutdownsControl board, sensorsPower supply, contacts, sensor resistance

Circuit pressure, leaks and cold radiators

The hydraulic part of the boiler pushes heating water through the circuit and holds the working pressure. Its faults show up immediately: the gauge needle drops, a puddle forms under the casing or the radiators stay cold.

Why the pressure drops to zero

Pressure in a closed heating circuit drops for one of two reasons: a leak, or an expansion tank that has lost its air cushion. A leak can be obvious, like a drip at a pipe joint, or hidden, when heating water drips inside the casing onto the hot heat exchanger and evaporates at once. A tank without air can no longer absorb thermal expansion: during heating the pressure jumps, is released through the safety valve, and after cooling falls below the working level. The owner tops up the system with the filling valve, and the cycle repeats. A tank problem shows itself as a needle that jumps with every heating cycle, while a leak shows as a slow pressure drop even when the boiler is off. The opposite also happens: with a crack in the secondary heat exchanger, mains water flows into the circuit and the pressure rises every time a hot tap is opened. If the needle drops within a day after topping up, look for moisture under the joints and around the safety valve instead of adding water again and again.

Water under the casing and release through the valve

A puddle under the boiler means either the safety valve has opened or a gasket on the pump, heat exchanger or valves is leaking, so we first find the leak point and only then select the part. The valve releases water when pressure is too high, so the valve itself is often fine and the real culprit is the tank or overfilling. Rubber seals harden from heat over time and stop holding the joint, while drips on the pump come from the cover O-ring or a crack in the plastic housing. Our gas boiler repair services also include an expansion tank check: its pressure is measured with a gauge and pumped back to normal if the diaphragm is intact. Replaced gaskets, valves and pumps are covered by a 1-year warranty on labor and parts. Before the technician arrives, place a dry paper towel under each joint — the wet spot will show exactly where the drip comes from and make the leak search shorter.

The boiler is hot but the radiators are cold

  • Closed valves: a flow or return valve left shut after summer flushing gives exactly the same picture as a faulty pump.
  • Air in the system: an air pocket at the top of the circuit stops circulation, and we bleed it through the pump and radiator air vents.
  • Seized pump: after standing idle all summer, the circulation pump rotor sticks, so we free the shaft or replace the motor completely.
  • Clogged filter: the mesh filter on the return line collects scale and sludge, so cleaning it is part of our hydraulic inspection.
  • Tip before calling: check every valve under the boiler and on the manifold — sometimes opening a valve solves the problem without a visit.

Hot water, scale and boiler type

A boiler heats tap water through its own circuit, separate from space heating, and its weak points depend on the design: combi, system boiler with a cylinder, floor-standing or condensing.

Radiators are warm but the tap runs cold

When the heating works but cold water comes out of the tap, the fault is looked for in two components: the three-way valve and the flow sensor. The three-way valve switches hot heating water between the radiators and the secondary heat exchanger; if its stem has seized or its actuator has burned out, the boiler keeps heating the radiators and ignores the open tap. The flow sensor, with a magnetic impeller or a flag, tells the board that water has started to flow, and if it sticks, the unit never learns about the demand. There is a third pattern too: the water runs hot, then cold, then hot again — that is how a boiler with a worn valve or an underset hot water output behaves, and in a system boiler with a cylinder a faulty cylinder temperature sensor shows up the same way. Before calling, check the cold water pressure in your flat: with weak pressure the flow sensor does not trigger and heating never starts.

Scale in the secondary heat exchanger

Scale in the plate-type secondary heat exchanger lowers hot water temperature and flow, so we either flush it or replace it if the plates are corroded through. Hard tap water deposits minerals where it gets hottest, in the narrow channels between the plates. The owner of a combi model notices this as weak heating, noise when a tap is open and overheating shutdowns. Heat exchanger flushing is part of our gas boiler repair in Almaty whenever someone complains about weak hot water: we check the plates before replacing the whole unit. The flushing solution is chosen to suit the heat exchanger material, and afterwards the seal and outlet temperature are checked. Corrosion through the plates gives itself away when circuit pressure rises on its own without topping up. To keep the plates from scaling up again, fit a water softener filter on the cold water inlet along with the flushing — it protects both the heat exchanger and the flow sensor.

Weak points of different boiler types

Boiler typeWeak pointWhat the technician does
Wall-mounted combiSecondary heat exchanger, three-way valveFlushes the plates, replaces the valve
System boiler with cylinderCylinder sensor, valve actuatorChecks the sensor and actuator
Floor-standingBurner, safety controlsCleans the burner, adjusts the gas valve
CondensingCondensate trap, fanCleans the trap, checks the draft
Through-wall (parapet)Thermocouple, flue through the wallChecks the thermocouple and draft

Control board, sensors and error resets

The electronics decide when the boiler lights the burner, how much power it uses and when it stops. Their faults look like random shutdowns, a frozen display or errors that come back after a reset.

The boiler won't turn on after a power cut

After a voltage surge, a silent boiler most often has a blown fuse or damaged power supply components on the board, so we test the control board before suggesting a replacement. Boiler electronics are sensitive both to overvoltage and to the plug being connected with the wrong phase, and the display may stay lit while the burner refuses to start. A Tech Service technician tests the fuse, the varistor and the relay supply, then decides whether to repair the board or fit a new one. Repairing it is much cheaper than replacing it, so the price of gas boiler repair after a power cut depends above all on which component burned out. Moisture on the board from a leak above produces similar symptoms, and it is ruled out during the inspection too. A voltage stabilizer of the right capacity protects the board better than an ordinary surge protector and pays for itself with the first serious surge.

How many times you can reset an error

It is reasonable to reset an error on the display once, but if the same lockout returns, the protection has tripped for a real reason. The code points to a group of components — ignition, draft, pressure, overheating — but not to a specific part: the same ignition error can come from a closed gas valve, a worn electrode or a faulty board. Frequent resets are dangerous: the gas in the chamber has no time to clear, and the next ignition happens with a bang. Overheating errors have their own logic — the boiler shuts down so the water in the heat exchanger does not boil, and restarting it again and again without finding the cause damages the unit. If the lockout keeps happening in the same situation, for example when hot water is turned on, the search narrows down to one circuit. Before resetting, take a photo of the display with the code and note when it appeared — from the photo the technician immediately knows which group of components to check first.

Sensors that make the boiler cycle on and off

  • NTC temperature sensors: a sensor whose characteristics have drifted reads too low, so the board lights the burner and then shuts it off a minute later.
  • Oversized output: a boiler with more power than the home needs quickly reaches the set temperature and goes into a pause.
  • Room thermostat: a thermostat near a window, radiator or front door picks up drafts and sends switch-on commands far too often.
  • Clogged circuit: weak circulation through a blocked filter overheats the heat exchanger, and the boiler shuts down before the radiators warm up.
  • Cost of short cycling: frequent starts wear out the ignition electrode and the gas valve, so this mode should not be tolerated all season.

How gas boiler repair at home works

Before the technician arrives, the owner can safely check a few simple things, but some signs mean you should not wait. Below is also what happens once the technician is on site.

What to check yourself before calling

  • Gas valve: the handle of the valve on the pipe in front of the boiler should run along the pipe; across it, the gas supply is shut off.
  • Pressure: on a cold boiler the gauge needle should be in the working zone; if it is lower, top up the circuit following the manual.
  • Power: check the plug, the socket and the circuit breaker, and if you have a stabilizer, its indicator and operating mode.
  • Settings and reset: make sure heating mode is on and press reset once; if the error comes back, do not open the casing.
  • Thermostat batteries: a wireless room thermostat with flat batteries stops sending commands, and the boiler simply stays in standby mode.

When you need a technician without waiting

  • Smell of gas: close the valve, open the windows, do not switch on lights and call the gas emergency service; the boiler is repaired once the leak is fixed.
  • Soot and smoke: soot on the casing means the draft is disturbed, so urgent gas boiler repair is needed, and we arrive within 60 minutes.
  • Bangs on ignition: a loud bang points to delayed ignition or a dirty burner, so it is better to switch the boiler off until it is inspected.
  • Water from the casing: if it leaks, unplug the boiler and close the valves, otherwise water will reach the control board.
  • Repeated lockouts: if the boiler goes back into an error after a single reset, further attempts only harm the burner and electrodes.

The technician's visit step by step

A Tech Service technician arrives within 60 minutes anywhere in the city, runs free diagnostics, quotes the cost of the work and starts only once the owner agrees. Diagnostics include inspecting the burner and electrodes, measuring gas and heating water pressure, and checking the draft, the pump and the control board. We replace electrodes, sensors, pumps, valves and gaskets on site — that is how gas boiler repair at home works, without taking the unit off the wall. Complex board soldering is done in our service center, and we take only that part, not the whole boiler. The work is done by our technicians with 4 to 20 years of experience, and you can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies. After the work, the boiler is started in both modes, heating and hot water, to make sure the error does not return. Before the visit, have the boiler manual ready or take a photo of the rating plate under the bottom cover — with the exact model, the technician finds a compatible part faster.

Warranty and getting the boiler ready for the heating season

After the technician's visit, owners care about two things: what the work will cost and how long the boiler will run without another call-out. This section covers the bill, the warranty and autumn maintenance.

What the final bill depends on

The final amount depends on how complex the fault is and on the cost of the replacement part, so we name it only after free diagnostics. Cleaning a pressure switch tube or replacing an electrode differs severalfold in labor from, say, replacing a secondary heat exchanger or a control board. The technician takes measurements first, and only then does the scope of work become clear, which is why general prices for gas boiler repair without an inspection are only a rough guide. The brand matters too: parts for Korean Navien, Rinnai and Kiturami boilers and for European Baxi, Bosch or Protherm units differ in price. If an expensive part is needed, you get the options before any work starts and decide for yourself. On an old boiler with a burned-out main heat exchanger, compare the cost of the part with the price of a new unit — sometimes replacing the boiler makes more sense than repairing it.

What the warranty on labor and parts covers

We give a 1-year warranty on labor and parts, which applies equally to the technician's work and to the new part. For a boiler this combination matters: a fault can come back either because of the part itself or because of the assembly — a poorly seated gasket, an incorrectly adjusted gas valve or a loose contact on the board. The warranty covers both sides, so the owner does not have to work out what exactly failed. The work is done by our own technicians with 4 to 20 years of experience, with no intermediaries, and the same service that came out to you is responsible for the result. Diagnostics are free, and you can pay for the work in any way you like. Keep the technician's contact details and note which part was replaced and what the original symptom was — if the sign returns, this will shorten the search for the cause.

Getting the boiler ready for winter

  • Burner inspection: dust and soot that build up on the burner over summer cause an uneven flame and bangs, so it is cleaned before the first ignition.
  • Heat exchanger: the main heat exchanger is checked for soot and leaks, and the secondary one for scale if hot water has become weaker.
  • Expansion tank: the air pressure in the tank is checked with the circuit drained and pumped up before the cold weather sets in.
  • Flue and draft: the coaxial pipe is inspected from outside, and the fan and pressure switch are checked in operating mode.
  • Test run: the boiler is switched to heating in advance, on a warm day, so that any fault shows up before the frosts rather than in the first cold week.

Gas boiler repair essentials for cold seasons

A gas boiler fails according to a clear logic of components, and knowing that logic helps the owner act calmly, safely and without unnecessary spending during the heating season.

  • The component matters more than the code: an error on the display points to a group of components — ignition, draft, hydraulics or electronics — but not to a specific part.
  • One reset: it is reasonable to reset a lockout once, but if it returns, there is a real fault that has to be found by measurement.
  • Pressure and leaks: a falling gauge needle and a puddle under the casing are linked to the expansion tank, a valve or the gaskets.
  • Safety: a smell of gas, bangs or soot mean you should switch the boiler off at once and close the valve until a technician arrives.
  • Autumn maintenance: cleaning the burner, checking the tank and doing a test run before the cold weather reduce the risk of a winter breakdown.

20brands

Which gas boiler brands we repair in Almaty

Brands that have their own pages on the site. Choose your brand to go to its repair page.

We also repairWe also repairTECH SERVICE09

Besides gas boiler repair, we fix other equipment in Almaty

Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.

BlogBlogTECH SERVICE10

Worth reading before gas boiler repair in Almaty

Leave a review

Choose a platform — the TECH SERVICE page will open.

2ГИС2GISGoogle MapsЯYandex Maps
Send a review with photos on WhatsApp