Original
Original bearings
- Selection
- By part number or machine model
- Compatibility
- Exactly matches factory specifications
- Delivery time
- Confirmed with the technician
- Warranty
- 1 year on labor and parts
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 746 00 26Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city, diagnostics are free. We replace bearings with a 1-year warranty on labor and parts.
Our own technicians4 to 20 years of experience




60 minutestechnician arrival anywhere in the city
Freediagnostics
1 yearwarranty on labor and parts
Diagnostics are free, and we agree on the cost of work after them. A technician arrives within 60 minutes anywhere in the city, 1-year warranty on labor and parts, we accept Kaspi QR, Kaspi Red, card, cash and bank transfer.
01
Step 1—
The technician removes the tub and takes it apart to access the drum support assembly.
02
Step 2—
Worn bearings are pressed out with a special tool without damaging the seats.
03
Step 3—
New bearings are pressed in, and the seal is replaced if needed to protect the assembly from water.
04
Step 4—
The tub is reassembled and put back in place, and the technician checks the drum rotation and play.
05
Step 5—
A test wash and spin cycle is run to make sure the noise and vibration are gone.
5
Five signs help suspect bearing wear, but the exact cause will be determined by a technician after free diagnostics.
Noise and vibration during spin
Causes include an unbalanced load, worn shock absorbers, or a worn bearing. The technician will check the drum play.
Leak under the machine
Water may come from hoses, the pump, or the pipes. The door seal leaks at the front, not from underneath.
Error on the display
The code points to a specific component: drainage, water intake, heating, or the motor, not a control board failure.
The machine won't drain
Check the drain filter at the bottom front behind the service flap — a common cause of clogs. If it's clean, the pump may be worn.
Not heating water
In Bosch and Siemens, the heating element is at the front and the pump at the bottom. The cause may be the heating element or the temperature sensor.
If the filter is clean but water won't drain, the cause may be the pump — it is checked after diagnostics.
Describe the symptomsWe select bearings by part number or machine model. For Bosch, the E-Nr number is on the label inside the door. Price — after diagnostics.
Original
or
Analog
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
2–4 hourstime
from 11 500 ₸cost

BeforeAfterThe home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsExpert washing machine repair technician
experience8 yearsSenior washing machine repair technician
experience9 yearsWashing machine repair technician
We reply during working hours
Let us know the machine model, the type of noise, and when it started — the technician will bring the right bearings and seal. This speeds up the repair and avoids extra trips.

Warranty question? Call us
+7 (778) 746 00 267 898 reviews of repairs at TECH SERVICE in total
Айгуль К.Order No. ZK-9431 · 15 November 2024
oursПробовал найти мастера в своём районе, но все были заняты. Утром работало, днём сломалось, вечером я уже искал сервис. Первое, что заметил: шумит при отжиме. Разобрали, посмотрели: помпа. Мастер сразу сказал, что к чему, без размытых формулировок. Шум пропал, работает мягко
Ольга М.Order No. 2024-4744 · 24 September 2024
oursПоломка застала перед командировкой, тянуть было нельзя. Сказать, что доволен — ничего не сказать.
Вероника П.Order No. TS-2205-922 · 11 October 2022
oursМастер үйге келіп, орнында тексерді. Бір күнде жөндеп берді, кешіктірмеді. Бағасын алдын ала келістік, соңында өзгерген жоқ. Ескі бөлшекті қайтарып берді, әдетте олай жасамайды. Қосымша бөлшек қажет болды, бірақ бағаны көтермеді. Алдын ала айтқан уақыттан ерте бітірді. Жөндеуге кепілдік бар, сол сенімді.
Акбота Т.Order No. TS-3098 · 5 April 2022
oursХотел сначала вызвать мастера на дом, потом передумал. Записался на диагностику стирально-сушильной машины. С чем пришёл: не сушит. В списке работ — тэн. Приняли, выдали квитанцию, всё по-человечески. Ребёнок уже проверил на прочность, держится.
Николай Ч.Order No. 75801 · 9 October 2021
oursОтдельно спасибо мастеру — Рустем Т, терпения ему хватило. Проверил дома — всё на месте, ничего не забыли.
Павел Ш.Order No. 96500 · 19 June 2021
oursЖалоба простая: не греет воду. Ораз снял деталь, показал износ, вопросов не осталось. Проверил дома — всё на месте, ничего не забыли
Артём К.Order No. TS-2115 · 17 June 2020
oursНужен был счёт и чек, у нас техника на балансе организации. Больше всего напрягало: не сушит. Сказать, что доволен — ничего не сказать
Елдос К.Order No. 59231 · 18 April 2020
oursБірінші кезекте бағасын білгім келді, содан кейін әкелдім. Бағасын алдын ала айтты, артынан қосымша талап етпеді. Бағасын бірден айтпады, қайта сұрауға тура келді.
Сабина Г.Order No. ZK-7682 · 16 July 2019
oursПроблема — не отжимает. Рустем Т взялся за то, от чего другие отказались. Работает как раньше, придирок нет.
Полина В.Order No. 237011 · 28 June 2016
oursОсновная жалоба — ошибка на дисплее. Дильмурат С не стал навязывать дорогую запчасть, поставил нормальную. Сделали и забыл про проблему
Didn’t find the answer? Message us on WhatsApp.
Ask a questionThe technician gives you the exact price after a free diagnostic check: it depends on the model, the type of tub, and whether the assembly is replaced together with the seal. We don't quote numbers before the inspection, so we don't underestimate the scope of work.
Technically yes, but you need the tools, a puller, and experience taking the tub apart, or you can easily damage the drum or the spider. Without the skill, there's a higher risk that the machine will start humming again after a DIY replacement.
There's no clear leader: reliability depends on the series and on how you care for the machine, not just on the brand. The bearing assembly lasts longer in machines where the drum isn't overloaded and the filter is cleaned regularly — that matters more than the brand.
Spin the drum by hand: it should turn smoothly and almost silently. If you hear crunching and feel play when you rock the drum by hand, the support assembly is probably worn — a technician's inspection will tell you for sure.
Not necessarily: play can come from a worn bearing, a cracked spider, or a damaged seat. You can only tell them apart after taking the tub apart, so the technician first removes the tub and inspects the assembly.
Yes, we provide a 1-year warranty on labor and parts. If humming or play comes back after the repair, the technician will find the cause under warranty.
Tech Service replaces washing machine bearings in Almaty as a set with the seal, with a technician visiting your home within 60 minutes anywhere in the city. Diagnostics are free, the technician gives you the price after diagnostics, and we provide a 1-year warranty on labor and parts. Our technicians are in-house with 4 to 20 years of experience.
A humming noise during the spin cycle is the most common reason to call us, but the bearing isn't the only possible source. Let's look at how to identify the problem by sound, drum play, and error code on the display.
A worn bearing shows itself as a hum or roar during the spin cycle that gets louder as the speed increases (usually 800–1600 rpm depending on the model), and as drum play that you can feel by hand when you rock the drum. In the early stage, the sound is like a train and appears only at high speeds, but over time it becomes audible even during water fill and rinsing. The second sign is a rusty mark on laundry near the door: moisture gets into the bearing assembly through the worn seal and washes out the grease. The third is that the drum turns with resistance and hums even when turned by hand. If you hear knocking and see shaft movement when rocking the drum, the cause may be not only the bearing but also the spider, so it's better to have a technician check it rather than replace parts at random. The technician gives you the price for washing machine repair with bearing replacement after a free diagnostic.
The support assembly doesn't fail on its own—a chain of causes leads to wear, and every extra week with the humming makes the repair more expensive. Here's how the seal, water, and assembly failure are connected.
We replace the support assembly only as a set with the seal, because the seal protects it from water, and a worn lip seal will let moisture through to the new part again. The assembly has two bearings on the drum shaft, and both work together with the seal that presses against the shaft and keeps water inside the tub. Over time, the seal lip wears, moisture gets to the grease, the grease washes out, and the part starts humming. This washing machine bearing repair starts with checking both elements and the seal, not just the noisy part. Replacing only one bearing from the pair without the seal means leaving a worn part in the assembly and an open path for water, so the set extends the assembly's service life rather than increasing the amount of work.
A failed support damages the seat and the spider, and in advanced cases it damages the tub, so instead of bearing replacement you need a more serious repair. While the wear is just starting, the part hums during the spin cycle but the shaft still holds its geometry. Then the element falls apart, the shaft starts to wobble, damages the seat in the tub, and chips the drum spider—and with a sealed tub, such a pair often means replacing the whole assembly. Humming at an early stage is a reason to check the assembly, not to wait until the drum starts knocking: the earlier wear is found, the fewer parts are affected. We come for diagnostics within 60 minutes anywhere in the city, and it's free—that makes it easier to catch wear before it spreads to the tub.
Whether the bearing can be replaced depends on the design of the drum and the type of drive. So let's honestly break down when the assembly is replaced separately and when such work is impossible.
| Design | Is the bearing replaced separately | What the technician considers |
|---|---|---|
| Drum with tie bolts | Yes, as a set with the seal | Unscrewing the housing and the condition of the shaft |
| Sealed drum | No, the question of a complete drum assembly is decided | Integrity of the housing and the seat |
| LG Direct Drive | Yes, if the housing is split | No belt, its own drum mounts |
| Top loading | Yes, if the housing is split | Access to the assembly from above |
We select the part by the part number or model code, and for Bosch the E-Nr number is on the plate in the door, so the element matches your machine rather than being picked "by eye". Bosch series differ: older Maxx, Logixx and Classixx and current Serie 2, 4, 6, 8 are equipped with different assemblies, and the same component may not fit different lines. Using the number, the technician verifies the bearing, seal and fasteners before the visit so as not to bring a set that obviously won't fit. This approach saves time: when repairing a washing machine, bearing replacement doesn't turn into waiting for the right element on site. In our practice, checking by model code eliminates most compatibility errors — especially on lines where the manufacturer changed the assembly within the same series.
Bearing replacement is the longest job on a washing machine because it requires removing the drum and tub. Let's show what stages the process consists of and what the owner can do themselves.
Bearing replacement is the longest job on a washing machine because the technician removes the tub and drum, and for a split tub additionally unscrews it to reach the assembly. Then the old bearing and seal set is pressed out, the seat is cleaned, the new pair is pressed in and the tub is reassembled. Our washing machine bearing replacement in Almaty always includes a new seal: without it, the assembly's tightness cannot be restored and the noise returns. The technician arrives at your home within 60 minutes anywhere in the city, diagnostics are free, and there is a 1-year warranty on labor and parts. For comparison, the heating element on most brands is replaced without removing the tub, so bearing replacement requires more time and care than many other jobs.
Do-it-yourself bearing replacement is only possible with a split tub and the right tools, and with a sealed tub the bearing is not replaced separately, so you can't solve the task yourself. Even on a split design, you need to carefully unscrew the tub, press out the old pair and press in the new one strictly into the seat without damaging the seating surfaces. A mistake during unscrewing or pressing in the part leads to play and recurring noise, and sometimes to replacing the entire tub. In our practice, attempts to save money at the assembly stage ended in disassembling the machine again. Also note: without a new seal, the assembly leaks again. If you're unsure about the tub type, the technician gives the washing machine bearing repair price, which consists of labor and parts, after a free diagnosis — it will show whether the tub is split or not.
While the technician is on the way, it's important not to damage the machine, and after the repair — to understand what terms you get. Let's go through both points in order.
We provide a 1-year warranty on labor and parts, offer free diagnostics, and arrive within 60 minutes anywhere in the city, and the technician quotes the price after the inspection. Our specialists have 4 to 20 years of experience and either come to your home or accept the machine at our service center. Tech Service is a direct provider with its own technicians, not an aggregator or intermediary: the same service you called is responsible for the result. You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies. Free diagnostics show whether the bearings need replacing at all, and in that case the cost of replacing washing machine bearings is determined after inspecting the assembly. The price for this work depends on the model and the condition of the drum, so you know the exact amount before work begins. Before calling, check whether your drum is serviceable — this affects the scope of work, and for sealed models the calculation is done separately. In our experience, it's more honest to give a price range right after disassembly than to promise a sum blindly.
Here are the key things to keep in mind before contacting a service center: from the first signs of wear to what to do before the technician arrives.
If you ask, the technician will check other parts during the same visit.
Refrigerator Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
Washing machine error codes are self-diagnostic codes that point to a specific component: drain, water fill, heating, motor, or door lock.
29 January 2026 · 13 minutes read
If your washing machine won't spin, it's usually an unbalanced load, a clogged drain filter or hose, and less often the pump, belt…
19 January 2026 · 12 minutes read
If your washing machine isn't heating water, the heating element or temperature sensor is usually to blame, less often the control board or wiring.
25 December 2025 · 12 minutes read
If your washing machine won't turn on, first check the outlet, extension cord, and the circuit breaker in your panel, then the plug and power cord.
24 November 2025 · 13 minutes read