Original
Refrigerant as specified
- Type
- Refrigerant specified in the model's specifications
- Compatibility
- Fully matches specifications
- Selection
- By AC model
- Price
- After diagnostics
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 746 00 26Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Free diagnostics. 1-year warranty on labor and parts.
Our own technicians4 to 20 years of experience




60 minutestechnician arrival anywhere in the city
Freediagnostics
1 yearwarranty on labor and parts
The technician arrives with equipment to check pressure and find leaks. First comes free diagnostics, then vacuuming and refrigerant recharge. After the recharge, they check that the AC is working. 1-year warranty on labor and parts.
01
Step 1quick
Free pressure check, inspection of connections, and leak detection.
02
Step 2after recharge
After the recharge, the technician monitors pressure with a gauge over time.
03
Step 3before recharge
Removing air and moisture from the circuit before recharge.
04
Step 4as per procedure
Recharging by weight or pressure according to the model's specifications.
05
Step 5at the end
The technician checks cooling capacity and confirms there are no leaks.
5
Five main signs point to low refrigerant or a leak. The sooner you call, the easier it is to fix the cause.
Short compressor cycles
The outdoor unit turns on and off frequently — when refrigerant is low, the compressor can't reach operating mode.
Ice on the pipes
Frost on copper pipes indicates low refrigerant or poor heat exchange.
Hissing or bubbling
The sound may indicate a leak through microcracks or loose connections.
Oily stains near the pipes
Oil traces or frost at the outdoor unit connections are a sign of refrigerant leak.
Blowing warm air
The indoor unit blows barely cool air even at the lowest temperature setting.
Note the settings and outdoor temperature when the sign appears — this helps the technician find the cause faster.
Describe the symptomsThe refrigerant type is listed on the outdoor unit's nameplate.
Original
or
Alternative
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
Diagnostics and pressure check before refillexact price — after the free diagnostics
1–2 hours
from4 500 ₸
Full refill of split system 07–12 000 BTU (up to 1 kg)exact price — after the free diagnostics
2–4 hours
from10 000 ₸
1 visittime
from 9 500 ₸cost

BeforeAfterThe climate control equipment repair department in Almaty has 8 technicians with 4 to 20 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience14 yearsAir conditioner service technician
experience20 yearsSenior air conditioner installer
experience12 yearsAir conditioner repair technician
experience16 yearsIndustrial air conditioner technician
experience4 yearsAir conditioner service technician
experience14 yearsAir conditioner maintenance technician
experience5 yearsAir conditioner installation technician
We reply during working hours
Provide the brand and capacity of your split system, the floor, and which side the facade faces — the technician will bring the right refrigerant and equipment for high-rise work.

Warranty question? Call us
+7 (778) 746 00 267 898 reviews of repairs at TECH SERVICE in total
Богдан С.Order No. ZK-2025/276 · 15 December 2025
oursПозвонил в три места, здесь единственные назвали цену сразу. Первое, что заметил: не холодит. Проверили при мне, показали, что всё держит.
Евгений М.Order No. TS-8391 · 27 April 2024
oursМастер үйге келіп, орнында тексерді. Ұсақ ақауларды да тегін жөндеп берді. Бағасы мен сапасы сай.
Андрей П.Order No. 769819 · 11 October 2022
oursОсновная жалоба — не включается. Никита М взялся за то, от чего другие отказались. С тех пор ни разу не подвёл
Ержан А.Order No. 2022-1408 · 8 June 2022
oursРаботаю допоздна, поэтому нужен был сервис с нормальным графиком. Основная жалоба — не холодит один блок. Tech-service посоветовали в чате дома, спосибо им. Починили и дали гарантию на месяц!!
Эльмира Т.Order No. ZK-3396 · 2 March 2022
oursПозвонил в три места, здесь единственные назвали цену сразу. Работает как раньше, придирок нет.
Томирис Ж.Order No. ZK-2020/288 · 14 March 2020
oursСимптом был очевидный: не холодит. Дамир М перезвонил, когда всё было готово. Работает даже тише, чем до поломки
Мирас С.Order No. ZK-2019/494 · 29 August 2019
oursДамир М снял деталь, показал износ, вопросов не осталось. Включил, проверил, работает.
Светлана Д.Order No. ZK-2019/535 · 5 April 2019
oursДруг посоветовал, у него похожая история была. Поставили новую деталь: компрессор. Сказать, что доволен — ничего не сказать.
Алишер У.Order No. TS-1705-145 · 18 February 2017
oursДо этого обращался в другой сервис, там только развели руками. Записался на диагностику кондиционера. Повод для визита: не холодит. Внешне как новый, если не считать мелкой царапины.
Мадина Т.Order No. TS-3191 · 7 July 2016
oursБұрын осында ноутбук жөндеткенмін, сондықтан сеніммен келдім. Алдын ала айтқан уақыттан ерте бітірді. Ұсақ ақауларды да тегін жөндеп берді. Бағасын алдын ала келістік, соңында өзгерген жоқ. Тексеру кезінде бәрін өзі көрсетті. Қайта жүгінсем, осында келемін
Didn’t find the answer? Message us on WhatsApp.
Ask a questionThe easiest time to schedule installation and refilling is in the off-season — spring or fall, when technicians have fewer requests. In the summer heat, demand is higher, so booking a visit may take longer.
In a properly sealed system, refrigerant isn't consumed, so no scheduled refilling is required. A top-up is only needed after fixing a leak — it depends on the model and the condition of the lines.
Usually the procedure, including a pressure check, takes about an hour, but the exact time depends on the model and the length of the lines. If a leak is also being located, the technician's visit may take longer.
Besides the refrigerant, the technician checks the system pressure, inspects the connections, and looks for leaks if necessary. Only after that does he top up the system to the norm by weight or pressure.
Yes, if there's a partial loss, the refrigerant is simply topped up to the required amount without draining the remainder. A full drain is only done when replacing the refrigerant or during major repairs of the circuit, depending on the model.
The cause may not be the amount of refrigerant: a clogged filter, a dirty heat exchanger, or a faulty compressor can produce similar symptoms. The technician should check the entire system, not just the pressure.
Tech Service provides AC refrigerant recharge in Almaty at your home: a technician arrives within 60 minutes, runs a free diagnostic to determine whether the system needs refrigerant or the issue lies elsewhere. Our own technicians have 4 to 20 years of experience, and we provide a 1-year warranty on labor and parts.
The split system is blowing air but not cooling, and the owner immediately thinks of refrigerant. Let's break down which signs actually confirm a refrigerant shortage and when the cause is a different component.
During diagnostics, we regularly find that the loss of cooling isn't due to refrigerant but to clogged filters, a faulty board, or a worn compressor — recharging won't solve the problem here. A clogged intake mesh blocks airflow, the heat exchanger can't release cold, and the split system blows warm even with a fully sealed circuit. A burnt-out board module won't start the compressor at all, and a worn unit can't create the needed pressure differential even with a full refrigerant charge. A Tech Service technician, when visiting your home, first measures pressure and checks components, and only then decides whether a recharge is needed or the issue is elsewhere. If after recharging the AC still cools poorly or a smell appears from the indoor unit, the cause is a dirty heat exchanger or drain — that's a separate maintenance service, not a repeat procedure. Repair and AC recharge in Almaty often go together: after fixing the fault, the circuit is recharged so the system returns to normal operation.
The type of refrigerant determines which composition and pressure scale can be used for the recharge. Let's look at three common refrigerants, their compatibility, and recharge volume.
| Refrigerant | Where it's found | Recharge specifics |
|---|---|---|
| R22 | older split systems | does not mix with others |
| R410A | most household systems | requires precise weighing |
| R32 | modern units | separate pressure scale |
The recharge volume depends on the split system's capacity — 7 and 9 BTU units take less refrigerant than 12 and 18 BTU, and we determine the exact amount by weight, not "by eye." The technician quotes the cost of AC recharge in Almaty after a free diagnostic: the price includes only the volume actually needed for your specific unit. Our specialists use a manifold gauge set and scales — they dose refrigerant by mass, not by a single gauge reading. Recharging by weight takes longer than topping up by pressure, but it eliminates overfilling that causes the compressor to run overloaded. You can verify that the technician added exactly the right amount using the manifold gauge and scales — pressure-based dosing without weighing introduces an error that shows up a season later.
A home recharge isn't just "connect the cylinder and leave." Let's break down what the technician does step by step, what tools they bring, and why DIY attempts don't work.
Do-it-yourself recharging from a can without a gauge and scales almost always leads to overcharging or undercharging, and the procedure can't be done correctly without special equipment. Overcharging raises the circuit pressure above the operating level, and the compressor wears out; undercharging leaves the system oil-starved. Refrigerants R410A and R32 are blends that can't be topped up "partially" without knowing the exact mass from the system's nameplate. Checking pressure with a gauge without vacuuming doesn't remove moisture, and moisture in the circuit forms acids that destroy the compressor winding. Washing the air conditioner before recharging isn't mandatory, but a clogged heat exchanger distorts pressure readings — so it makes sense to combine maintenance with recharging rather than put it off. If you're unsure whether the unit can handle it itself, wait for the technician: they'll compare the readings with the nameplate and tell you if the procedure is needed at all.
Refrigerant isn't consumed like fuel — it circulates in a closed circuit. But there's always some minor loss, and it's important to distinguish normal loss from a real leak.
Natural refrigerant loss is small, and at that rate recharging is needed once every few seasons, not every month. Microscopic losses occur through the threaded connections of copper pipes: with temperature changes, the metal contracts and expands, and the seals gradually let through fractions of a gram of gas. Before recharging, a Tech Service technician checks the circuit for leaks rather than just topping up gas — if a leak is suspected, they use a UV dye and soap solution on the joints. Flare fittings and solder joints are inspected separately: that's where microcracks most often appear after vibration of the outdoor unit. If the system stops cooling again a month or two after service, it's not normal loss — in that case, our technician looks for a leak at the copper pipe connections and fixes it before recharging again.
A household split system and a car air conditioner use different refrigerants, different pressures, and different equipment — so services for cars and for apartments are not interchangeable. Most home systems use R410A or R32, older models may have R22, while cars use R134a. The pressure in a split system circuit is higher than in a car's, so a different manifold gauge station is needed. Refrigerant is dosed by weight taking into account the line length: each extra meter of piping adds grams that are accounted for on electronic scales. Car systems are charged by volume through a station, and there's no universal can "for everything." Mixing different refrigerants is not allowed — it damages the compressor, and restoring such a circuit costs more than doing the procedure correctly from the start.
Home service from a direct contractor works differently than ordering through an aggregator: here's what the warranty actually covers and how to call a specialist.
We give a 1-year warranty on labor and parts — if the problem comes back after service and it's our fault, a technician returns and fixes it under warranty. During this period, we also cover refills and replacement of any failed components we installed. We handle warranty callbacks at no charge. The warranty does not cover a repeat leak through a damaged circuit — so it's important to assess the system's condition before refilling, to make it clear where our work ends and equipment wear begins. In my view, this clarity matters more than the refrigerant hose itself: it protects both the customer and the technician from a dispute six months down the line. If the circuit already has a crack, it's more honest to show it before refilling than to charge for refrigerant that will leak out within a month.
A Tech Service technician arrives within 60 minutes anywhere in the city, diagnostics are free, and the price depends on the system type and refrigerant volume — the technician gives you the exact amount after diagnostics. You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies. AC refill prices are higher for multi-split systems and ducted units: there's more circuit and the job takes longer. The difference between a household split system and a multi-split is obvious during the inspection, so we don't quote a price over the phone — it will change anyway after pressure testing. Booking service in advance during hot season makes sense a day or two ahead: at peak load, available slots shrink, and an urgent call in the middle of the day means more travel time. Plan your home AC service before the first heatwave, not on the day the unit stops cooling.
We've covered the key factors that determine the result of an AC refill: how the decision is made, how the procedure is carried out, and why the cold stays in the system for a long time.
If you ask, the technician will check other parts during the same visit.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Air conditioner errors are codes on the display or flashing indicators that show which component has failed.
5 March 2026 · 12 minutes read
If your air conditioner is leaking, first turn it off and cut the power, place a container under the drip, and move any wiring away from the water.
19 October 2025 · 12 minutes read
Gas boiler errors are codes on the display or a flashing indicator that point to a specific component: ignition, pressure, draft, sensor, or control board.
10 February 2026 · 11 minutes read