experience9 yearsRuslan Ts.
Washing machine and refrigerator repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 046 88 53Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
We restore your generator on site. Technician arrives within 60 minutes anywhere in the city.
Our own technicians4 to 20 years of experience




Repair prices
The most frequent symptoms and their likely causes. The technician names the exact cause after diagnostics.
no fuel, flooded spark plug, dead battery
from2 000 ₸
clogged filter, AVR fault, dirty carburetor
from2 000 ₸
damaged winding, failed AVR or brushes
from2 000 ₸
blocked cooling, low oil, overload
from3 500 ₸
loose mounts, worn bearing
from3 000 ₸
hardened gaskets, worn oil seals
from8 000 ₸
the code points to a unit, measurement needed
from6 500 ₸
worn spark plug, dirty carburetor
from2 500 ₸
Pick a group of jobs by symptom and the table will show the matching items with the labor price.
1–2 hourstime
from 2,500 ₸cost

BeforeAfter5 steps

Five steps from your request to a test of the generator under load.
Describe the symptom and model so the technician can prepare tools and parts.
The technician confirms the model and symptom by phone to bring the right tools and parts.
The technician finds the cause and names the cost before the repair starts.
You approve the scope and price, and only then does the repair begin.
Start-up under load and a check that the old symptom is gone.
The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience12 yearsGeneral household appliance repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsExpert washing machine repair technician
experience8 yearsField refrigerator repair technician
experience8 yearsSenior washing machine repair technician
experience11 yearsDishwasher repair technician
experience9 yearsWashing machine repair technician
We reply during working hours
Tell us the generator model and the symptom: won't start, stalls or gives no power. The technician will come to your house or country home and name the cost after the check.

Warranty question? Call us
+7 (778) 046 88 537 898 reviews of repairs at TECH SERVICE in total
Алия Ш.Order No. ZK-2024/983 · 6 October 2024
oursНужен был счёт и чек, у нас техника на балансе организации. Повод для визита: не даёт напряжение. Ребёнок уже проверил на прочность, держится.
Даулет С.Order No. TS-1136 · 17 February 2024
oursС чем пришёл: не заводится. Рустем Т помог выбрать, без навязывания. Пользуюсь ежедневно, вопросов нет.
Владимир Н.Order No. 2023-2292 · 19 September 2023
oursЦена имела значение, но и гарантия тоже. Настроение было испорчено конкретно. Основная жалоба — не заводится. Поменяли: карбюратор. Tech-service оказался ближе всех, за это и выбрал. Включил, проверил, работает.
Светлана Д.Order No. TS-2310-932 · 12 April 2023
oursБұрын басқа сервиске барғанмын, бірақ бұл жолы осында келдім. Техника кенеттен істен шықты, қатты асығыс едім. Себебі қуат беру модулінде екен, бір сағаттың ішінде ауыстырды. Бәрі жақсы, шағымаймын.
Санжар О.Order No. 34300 · 13 February 2023
oursПоломка застала врасплох: не даёт напряжение. Отдал 9 500, и это вместе с работой. Мастер показал, что меняет: альтернатор. Приняли без предоплаты, это подкупило. С чистой совестью советую. Сделали аккуратно, следов разборки не видно.
Ильяс Н.Order No. 334114 · 10 January 2023
oursПозвонил в три места, здесь единственные назвали цену сразу. После выходных обнаружил: не заводится. По деньгам вышло адекватно, в другом месте просили больше. Поставили новую деталь: альтернатор. Работает как раньше, придирок нет.
Алмас Д.Order No. 2022-1444 · 8 December 2022
oursПозвонил в три места, здесь единственные назвали цену сразу. Позвонил узнать про ремонт генератора. Жалоба простая: не заводится. Дамир М всё объяснил и не пытался впарить лишнее. Цену обсудили до начала, сюрпризов не было. Объяснили по телефону, что можно не везти, но я всё равно привёз. Поставили новую деталь: регулятор. Не пожалел ни разу. Шум пропал, работает мягко.
Алмас Д.Order No. TS-2201-527 · 5 December 2022
oursОтдельно скажу про мастера: Рустем Т — спокойный, без лишней суеты. Уже полгода — ни одного сбоя.
Жасмин Р.Order No. TS-2104-997 · 26 January 2021
oursЖалоба простая: не даёт напряжение. Дамир М помог выбрать, без навязывания. Второй месяц — полёт нормальный.
Алишер У.Order No. 303029 · 21 February 2020
oursДолго откладывал ремонт, потом всё-таки собрался. Утром работало, днём сломалось, вечером я уже искал сервис. С чем пришёл: не даёт напряжение. Вышло дешевле нового, что логично. Позвонил, описал проблему, сказали привозить — посмотрят в тот же день. Заодно поменяли: регулятор. Спасибо за работу. Починили и дали гарантию на месяц
Дамир И.Order No. 640190 · 15 February 2019
oursАлдын ала бірнеше жерге қоңырау шалдым, бірақ нақты жауап осында ғана алдым. Бірінші рет осында жүгіндім, бұрын басқа жерге барғанмын
Нурасыл М.Order No. 87641 · 22 December 2018
oursХотел сначала вызвать мастера на дом, потом передумал. Жалоба простая: не заводится. Второй месяц — полёт нормальный
Динара М.Order No. 45363 · 13 October 2017
oursИскал мастерскую поближе к дому, чтобы не мотатся с техникой через полгорода. С чем пришёл: не заводится. Уже полгода — ни одного сбоя.
Эльмира Т.Order No. 78373 · 7 July 2017
oursОтдельно скажу про мастера: Рустем Т — спокойный, без лишней суеты. Вернули в тот же день, всё функционирует)
Дамир И.Order No. TS-6150 · 6 April 2016
oursТехника на гарантии уже не была, так что выбор был свободный. Проблема — не даёт напряжение. Проверил дома — всё на месте, ничего не забыли.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionThe time depends on the issue: adjusting the carburetor or replacing the brushes takes less time than rebuilding the engine or windings. The technician gives you an exact timeframe after free diagnostics. The warranty on labor and parts is one year.
A faulty generator unit may stall, fail to supply voltage to the outlets, overheat, or run intermittently. In the case of a car generator, the battery warning light comes on on the dashboard, and the engine runs unevenly.
When the brushes wear out, the output voltage drops or fluctuates heavily, the lights flicker, and the outlets may not deliver power. It depends on the model, but most often the unit runs but doesn't charge. The technician will check the brushes and replace them if needed.
Most often the cause is fuel delivery: a clogged carburetor, old gasoline, or a dirty filter. A faulty oil level sensor or ignition issue is also possible. The technician will check the fuel system and electrics on site.
If the engine runs but there is no power at the outlets, the voltage regulator, brushes, or windings are to blame. Sometimes a circuit breaker trips. Diagnostics will show which component has failed, and the technician will then replace or repair it.
Yes, the technician can fix many issues on site: carburetor, ignition, voltage regulator, brushes. If major engine or winding repairs are needed, the unit is taken to the service center. The decision is made after free diagnostics.
We handle generator repair in Almaty with our own technicians: gasoline, diesel and inverter units for homes and country houses. The technician arrives within 60 minutes anywhere in the city, diagnostics is free, and we name the cost after it. We give a 1-year warranty on labor and parts, and our technicians have from 4 to 20 years of experience.
A generator combines an engine, an alternator and an outlet panel in one frame. The symptom shows which of the three systems to check first, and that saves the owner time.
We start with free diagnostics: we run the unit, listen to the engine and measure the output voltage first with no load and then with an appliance plugged in. This approach to generator repair in Almaty separates mechanical and electrical faults right away, so parts are not replaced at random. Our technician, with 4 to 20 years of experience, watches how the engine speed behaves, whether the indicators stay steady, and whether there is a burning smell or oil under the frame. Then he removes the cover and inspects the spark plug, air filter, regulator terminals and brush assembly. The cause and the cost of the work become clear after this check, not from a description over the phone. The practical rule is simple: if the voltage drops together with engine speed, we look for the cause in the engine and fuel, and if the speed is steady but there is no power, in the alternator and regulator.
| Symptom | Likely unit | What we check first |
|---|---|---|
| Won't start, starter turns | Spark plug, carburetor, fuel valve | Spark and fuel supply |
| Starts and stalls at once | Oil level sensor, jet | Oil level and idle |
| Engine speed hunts | Carburetor, air filter | Filter condition and mixture |
| Stalls under load | Fuel filter, overload | Appliance wattage and fuel supply |
| Runs but gives no power | AVR, brushes, circuit breaker | Regulator output and breaker |
| Voltage jumps | AVR, speed governor | Voltage at idle and under load |
| Blue smoke, oil consumption | Piston rings, oil seals | Compression and plug deposits |
Gasoline, diesel and inverter generators fail in different ways because their fuel systems and the way they produce power are different. A gasoline model with a carburetor is sensitive to stale fuel and a dirty air filter, while its alternator with an AVR regulator feeds voltage straight to the outlets. A diesel unit has no carburetor or spark plug: fuel is delivered by a high-pressure pump and an injector, so its weak points are fuel quality, air in the lines and hard starting in frost. An inverter model first produces alternating current, rectifies it and then rebuilds a sine wave on an electronic board, adjusting engine speed to the load. Because of this design, an error on an inverter panel does not always mean the board has failed: the windings that power it are checked first, and only then is a new module considered.
The engine usually fails for three reasons: fuel, ignition and low-oil protection. We go through each of them and then look at how the engine behaves under load when the unit starts to stall.
Gasoline left in the carburetor float bowl for several months oxidizes and leaves gummy deposits in the jets and on the needle valve. The idle jet passages are very narrow, so even a thin film blocks the mixture, and the engine either won't catch or runs only with the choke partly closed. The symptoms are easy to recognize: it starts only on choke, the speed surges, and the engine stalls when the choke is opened. The fix is a carburetor cleaning with the passages blown out and the fuel filter replaced, and sometimes a tank flush if water and rust have collected at the bottom. Fresh gasoline in an old tank does not solve the problem, because the deposits stay in the bowl and clog the jet again. Before long storage, close the fuel valve and let the engine run until it stops by itself: the carburetor stays dry, and in spring the unit starts without being taken apart.
A generator stalls when a pump, boiler or fridge is switched on for one of two reasons: the appliance's starting current exceeds the power reserve, or the engine itself cannot deliver its rated output. A borehole pump motor draws several times its rated current at start-up, and the speed governor does not have time to open the throttle. If the engine stalls even at half load, we check the air and fuel filters, the governor linkage, the compression and a muffler clogged with carbon. Our technician compares the total wattage of your appliances with the rating plate on the frame and tells you which equipment can run at the same time. One simple operating rule reduces the strain on the engine: switch appliances on one by one, starting with the most powerful, and give the unit a couple of seconds to reach speed before the next one.
The engine hums steadily, but the lights stay off or flicker, which means the fault is in the electrical part. There are three places to look: the alternator, the regulator and the outlet panel.
When the engine runs smoothly but the panel voltmeter shows zero or jumps, we check three alternator units: the AVR regulator, the brush assembly and the stator and rotor windings. The AVR supplies excitation current to the rotor and holds the output voltage as the load changes; when it fails, the voltage disappears or rises above normal. Brushes wear down over time and lose contact with the rotor slip rings, and after a long idle period the alternator sometimes loses its residual magnetism, so it does not generate at all. We test the windings with a multimeter for open circuits and shorts to the frame and compare their resistance with neighboring sections. In our view, overvoltage is more dangerous than no voltage: if the lights flare up brightly, unplug your equipment at once until the regulator has been checked.
| Fault | How it shows | What we do |
|---|---|---|
| Circuit breaker tripped | No power at outlets, engine running | Find the overload, reset the breaker |
| AVR failure | Zero or jumping voltage | Replace the regulator, check excitation |
| Worn brushes | Power cuts out with vibration | Replace brushes, clean slip rings |
| Loss of residual magnetism | No power after storage | Restore rotor excitation |
| Winding turn-to-turn short | Burning smell, weak voltage | Rewind or replace the stator |
| Burnt outlets | Melted housing, hot plug | Replace the outlet and panel wiring |
| Inverter module fault | Overload error with no load | Check board supply, replace the module |
An inverter generator delivers power through an electronic module, so a board fault shows up as an overload indicator, outlets cutting out at idle, or a hum with no voltage output. The design has two stages: a multi-pole alternator produces high-frequency alternating current, and the board rectifies it and forms a new sine wave at the standard grid frequency. As a result, the voltage waveform is cleaner than that of a conventional brush-type unit, and the engine slows down at light load and uses less fuel. The weak point is heat: the module is cooled by airflow, and dust on the heatsink or clogged vents in the cover make the electronics overheat. A gas boiler, a computer and a TV are best powered from an inverter model, while a welder or a rotary hammer with high starting current is better on a conventional one.
An owner can make a few checks on their own and save time. There are also things best avoided before the technician arrives, because they put people at risk or make the damage worse.
The more precisely you describe the model, the symptom and the circumstances of the failure, the better our technician can prepare for the visit. Give the brand and model from the rating plate, the fuel type and power output, and when the unit was last serviced and had its oil changed. Explain what exactly happens: the engine won't turn over, catches and stalls, runs with no power at the outlets, or shuts down under load. The conditions matter too, such as storage over winter, fuel from a new can, a welder or pump being connected, or a fall during transport. Say where the unit stands, at a private house, a country home or a work site, and whether there is access to it. Take a photo of the rating plate and the indicator panel: it shows the power, alternator type and regulator, so the technician brings the right tools the first time.
Below is how the visit goes, which work is done at the owner's site and which at the service center, and how the result is checked before the unit goes back into use.
Our technician arrives within 60 minutes anywhere in the city and carries out diagnostics free of charge, whether at a private house, a country home or a construction site. Generator repair in Almaty is done by our own technicians, with no middlemen: the same specialist who checked the unit names the cause and the cost of the work and then carries out the repair. With 4 to 20 years of experience, he works with gasoline, diesel and inverter models of common brands. Diagnostics includes a start-up, a voltage measurement and an inspection of the fuel system, ignition and electrical part. You can pay in whatever way suits you, since Tech Service accepts Kaspi QR, Kaspi Red, card, cash or bank transfer. To make the check go faster, clear the space around the unit, give access to the panel and have ready the appliance the generator failed on: under that load the technician will reproduce the fault.
| Job | Where we do it | How we check the result |
|---|---|---|
| Carburetor cleaning and adjustment | On site | Smooth idle and throttle response |
| Spark plug and filter replacement | On site | Starts within the first attempts |
| Recoil starter repair | On site | Free travel and cord return |
| AVR and brush replacement | On site | Voltage with no load and under load |
| Outlet and breaker replacement | On site | All panel outlets working |
| Stator winding rewind | At the service center | Resistance and voltage under load |
| Piston assembly repair | At the service center | Compression and clean exhaust |
We give a 1-year warranty on labor and parts, and we hand over the repair under real load, not just at idle. After assembly, the technician starts the unit, lets the engine warm up and connects household appliances such as a heater, a pump or a power tool, whatever the owner has at hand. The panel voltmeter or a multimeter shows whether the voltage holds as the load is connected and removed, and listening reveals any knocking or vibration. We also check separately for oil and fuel leaks under the frame after a few minutes of running. The warranty covers both the work done and the parts installed. Test the very appliance the generator failed on together with the technician: if the pump or boiler starts confidently, the cause has been fixed, not masked.
A backup power unit is needed on the day of a power cut, and that is exactly when you find out how it was stored. Oil and filter service and proper storage prep decide whether it starts on the first try.
Oil in a generator's four-stroke engine is changed by engine hours according to the model's manual, and the first change is made after a short break-in of a new or rebuilt engine. A foam air filter element is washed and lightly oiled, while a paper one is replaced when it darkens and lets little air through. The fuel filter and spark plug are serviced on the schedule in the unit's manual. Exhaust color tells you about the engine's condition: black smoke means a rich mixture and a dirty air filter, white smoke on a warm engine means water in the fuel, and blue smoke means oil in the combustion chamber. During an inspection we check all three signs, as well as the oil level and color on the dipstick. Blue smoke after warm-up is a reason to check the rings and valve stem seals rather than top up oil: with wear, consumption only grows and carbon fouls the plug.
A backup generator is best checked before the cold sets in: start-up, voltage under load, battery charge and fuel condition. For a private house or country home, it is important to know in advance which appliances the unit will power during an outage, such as a boiler, circulation pump, fridge and lighting, and whether it has enough power for them given their starting currents. Diesel models need winter diesel fuel in frost, otherwise wax from summer fuel clogs the filter. During a seasonal check we change the oil and filters, adjust the carburetor or check the diesel fuel supply, and test the transfer switch. It is easier to schedule this check in advance than on the day the line goes down. Between checks, start the unit once a month under a light load: oil spreads over the parts, the battery recharges, and any fault shows up before the power goes out.
A generator fails for clear reasons, and the symptom almost always tells you which system to look at. Here is a short summary for owners before calling a technician.
16brands
We select parts for and repair generators of popular brands. Choose yours to open a page with the work we do on it.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your dishwasher won't drain, the most common culprits are a clogged filter or drain hose; less often, it's the pump, impeller…
24 March 2026 · 12 minutes read
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
The easiest way to remove scale from a kettle is with citric acid: 1–2 tablespoons per liter of water, boil for 5–10 minutes, then drain and rinse.
17 March 2026 · 13 minutes read
If your laptop screen is broken, turn the device off first, don't press on the display, and check the picture through an external monitor.
12 March 2026 · 11 minutes read
Air conditioner errors are codes on the display or flashing indicators that show which component has failed.
5 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read












