Open until 19:00+7 (778) 021 13 16Call a technician
Tech Service technician next to a tumble dryer

Tumble Dryer Repair in Almaty

A technician arrives within 60 minutes anywhere in the city. Free diagnostics.

  • 1-year warranty on labor and parts
  • 4 to 20 years of experience
  • Arrival within 60 minutes

Our own technicians4 to 20 years of experience

Ruslan Ts.Damir M.Dilmurat S.Dima

Repair prices

  • Diagnostics0 ₸
  • Heat exchanger (recuperator) replacementfrom5 000 ₸
  • Temperature sensor replacementfrom5 500 ₸
  • Drive belt replacementfrom5 500 ₸
  • Humidity sensor replacementfrom6 000 ₸
All prices
2ГИСЯours4,97 898 reviews
2GIS · Google · Yandex · order database
Common faultsCommon faultsTECH SERVICE02

Common clothes dryer faults in Almaty

Below are typical symptoms and likely causes. The exact cause will be determined during free diagnostics.

PricesPricesTECH SERVICE03

How much clothes dryer repair costs in Almaty

Select a symptom to see the relevant services and prices, excluding parts cost.

Heat exchanger (recuperator) replacementparts not included

1–3 hours

from5 000 ₸

Temperature sensor replacementparts not included

1–2 hours

from5 500 ₸

Drive belt replacementparts not included

1–2 hours

from5 500 ₸

Humidity sensor replacementparts not included

1–2 hours

from6 000 ₸

Heat exchanger and filter cleaningexact price — after the free diagnostics

1–2 hours

from6 000 ₸

Before and afterBefore and afterTECH SERVICE04

Before and after clothes dryer repair in Almaty

Condensate is not pumped out of the tank

1 visittime

from 8 000 ₸cost

Problem
A heat-pump dryer stopped every half hour with a full-tank error, although the container was empty.
What we did
The technician removed the lower panel, replaced the condensate pump, and checked the pumping.
Result
Condensate is again pumped into the container, and the machine runs without stopping due to a full-tank error.
I want the same
In the bathroom by a white dryer, the technician holds a removed condensate pump — a black housing with a white hose connector; next to it on a gray towel lies a new pumpBeforeAfter
01 / 03
All repairs
TECH SERVICE mobile technician with a tool case

How clothes dryer repair works at your home in Almaty

Five steps from request to checking the work.

  1. Requestsame day

    Describe the symptom and your machine model so the technician brings the right tools.

  2. On-site diagnosticson site

    The technician checks component by component and identifies the cause.

  3. Part selectionby model

    The technician ensures the part is compatible with your specific machine model.

  4. Repairwith your approval

    Work is done only after your approval; you can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies.

  5. Paperworkafter repair

    You receive documents and details of the work performed.

Leave a request
TechniciansTechniciansTECH SERVICE05

Our home appliance repair technicians in Almaty

The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

  • 8 technicians in Almaty
  • 8–12 years of experience in the department
  • Article author Ruslan Ts., 9 years of experience
Mobile technician fixing a washing machine at the customer's home
Field technician at a customer’s home

The department has 8 specializations — they are listed on the technicians' cards.

01 / 08
Ruslan Ts., washing machine and refrigerator repair technicianexperience9 years

Ruslan Ts.

Washing machine and refrigerator repair technician

Damir M., general household appliance repair technicianexperience12 years

Damir M.

General household appliance repair technician

Dilmurat S., field technician for washing machine and refrigerator repairexperience10 years

Dilmurat S.

Field technician for washing machine and refrigerator repair

Dima, expert washing machine repair technicianexperience8 years

Dima

Expert washing machine repair technician

Nikita M., field refrigerator repair technicianexperience8 years

Nikita M.

Field refrigerator repair technician

Oraz, senior washing machine repair technicianexperience8 years

Oraz

Senior washing machine repair technician

Radik T., dishwasher repair technicianexperience11 years

Radik T.

Dishwasher repair technician

Rustem T., washing machine repair technicianexperience9 years

Rustem T.

Washing machine repair technician

We reply during working hours

Book clothes dryer repair in Almaty

Choose a convenient visit time, and confirm diagnostics and payment details with the technician by phone.

TECH SERVICE administrator replying to a customer's WhatsApp message

Warranty question? Call us

+7 (778) 021 13 16
Customer reviewsReviewsTECH SERVICE06

Reviews of clothes dryer repair in Almaty

Ольга М.Order No. ZK-6854 · 28 April 2026

ours

С чем пришёл: не сушит. Рустем Т взялся за то, от чего другие отказались. Гудит ровно, не греется, всё как надо.

Repair: dryer

Дмитрий Л.Order No. TS-2512-620 · 19 September 2025

ours

Позвонил в три места, здесь единственые назвали цену сразу. Не думал, что вообще напишу отзыв, но тут стоит. Повод для визита: не греет. Дима объяснил причину так, что понял даже я. Объяснили по телефону, что можно не везти, но я всё равно привёз. Вышло дешевле нового, что логично. Поменяли: термостат. Включил, проверил, работает.

Repair: dryer

Карина А.Order No. 650164 · 10 April 2024

ours

Искал мастерскую поближе к дому, чтобы не мотаться с техникой через полгорода. Записался на диагностику сушильной машины. Основная жалоба — не сушит. Починили и дали гарантию на месяц.

Repair: dryer

Ксения И.Order No. ZK-8841 · 23 August 2023

ours

Үйдегілер «лақтыр» деді, мен шешім қабылдамай тұрып көрсетуге апардым. Алдымен интернеттен іздедім, кейін таныстарым осы жерді ұсынды. Тек кезекте аздап күттім.

Repair: dryer

Максат О.Order No. TS-2312-869 · 8 July 2023

ours

Нужен был счёт и чек, у нас техника на балансе организации. Жалоба простая: не греет. Работает как раньше, придирок нет.

Repair: dryer

Жанар Т.Order No. 94778 · 23 April 2023

ours

Основная жалоба — шумит. Отдельно скажу про мастера: Дима — спокойный, без лишней суеты. Включил, проверил, работает.

Repair: dryer

Ержан А.Order No. ZK-2022/802 · 1 November 2022

ours

До этого обращался в другой сервис, там только развели руками. Основная жалоба — не сушит. Сделали аккуратно, следов разборки не видно!!

Repair: dryer

Индира П.Order No. ZK-2022/427 · 15 June 2022

ours

Было подозрение, что дело в плате, хотелось услышать второе мнение. Основная жалоба — не греет. Проверили при мне, показали, что всё держит!!

Repair: dryer

Аскар Ж.Order No. TS-5997 · 27 April 2022

ours

Поломка застала перед командировкой, тянуть было нельзя. Больше всего напрягало: шумит. Ребёнок уже проверил на прочность, держиться.

Repair: dryer

Максим Ю.Order No. TS-2104-531 · 8 August 2021

ours

Было важно, чтобы сделали до выходных — гости, то-сё. До последнего откладывал, но пришлось признать: не сушит. Дима возился с этим дольше, чем планировал, но довёл до конца. Поменяли: термостат. Отдал 27 000, и это вместе с работой. Мастер посмотрел, сказал, что возьмёться, и взялся. Ребята из techservice работают давно, это чувствуется. Пять звёзд, не задумываясь. Нагрев в норме, посторонних звуков нет

Repair: dryer
Questions and answersQuestionsTECH SERVICE07

Questions about clothes dryer repair in Almaty

Didn’t find the answer? Message us on WhatsApp.

Ask a question
How often should you clean the lint filter in a dryer?

The lint filter should be cleaned after every cycle so air flows freely and the machine doesn't overheat. The heat exchanger and moisture sensor need cleaning less often, about once a month, and the exact procedure depends on the model.

How do you properly clean the condenser in a dryer?

The condenser (heat exchanger) is rinsed with warm water and a soft brush, left to dry completely, and put back in place. On heat-pump dryers, clean the fins carefully so you don't bend them; the procedure depends on the model.

Which dryer brand is good?

Heat-pump dryers from Bosch, Siemens, LG, and Samsung get good reviews: they're more efficient and gentler on your laundry. But any appliance needs care, and the choice depends on your budget and how much laundry you do.

Can a Korting dryer be repaired in Almaty if the brand is discontinued?

Yes, most of these machines can be repaired: the fault is found during diagnostics, and a suitable part is matched to the model. If the original part isn't available, the technician will suggest a compatible option.

My LG dryer is showing an error code. How can I decode it before the technician arrives?

Look up the code in your model's manual or on the sticker inside the door — each brand has its own decoding. Before the technician arrives, unplug the machine and don't take it apart; the code only points to the faulty component.

What should I do if the dryer stops drying again after a repair?

If the problem comes back, it's covered by warranty: there's a 1-year warranty on labor and parts. Contact the company that did the repair, describe the symptom, and a technician will come back to take another look.

Repair guideArticleTECH SERVICE08

Dryer repair in Almaty by Tech Service with a technician visit

Ruslan Ts., washing machine and refrigerator repair technician

Author: Ruslan Ts.,Washing machine and refrigerator repair technician

Published
Updated

Tech Service repairs dryers in Almaty with its own technician: he comes to your home or we fix the machine at our service center. Diagnostics are free, we arrive within 60 minutes anywhere in the city, and you get a 1-year warranty on labor and parts. The technician gives you the price after diagnostics.

Why your dryer stopped drying and how to find the cause

A dryer almost always signals a breakdown with a symptom, not a code. The technician's job is to link that symptom to a specific part of the drying chain, not to replace parts at random.

The drum spins but the laundry stays wet

If the drum turns but the clothes don't dry, we check the drying chain in order: heating, airflow, condensate drainage, and moisture sensors. In a condenser dryer, air passes through the lint filter, then through the heat exchanger where it releases moisture, and returns to the drum heated. A loss can happen at any step: a clogged filter, a heat exchanger caked with scale, a blocked drain channel, or a sensor giving false readings. A dryer maintenance technician runs through this entire chain before removing any part. Often a "dead" heating element turns out to be a clog that simply kept heat from reaching the laundry. Most often the culprit is not the heating element but a clogged lint filter or heat exchanger—they choke the airflow, and the machine dries with no effect.

The machine doesn't heat the air

When a condenser dryer doesn't heat, we look at the heating element, thermostat, or thermal fuse; in a heat-pump model, we check the compressor and refrigerant circuit. Diagnostics start with measuring the resistance on the coil and checking the control circuit: if the heating element is intact but there's no voltage, the thermostat or the board is at fault. A heat pump is different—the compressor circulates refrigerant through the circuit, and if there's a refrigerant leak or the compressor fails, the air stays cold even though the drum spins properly. We start dryer repair in Almaty with free diagnostics precisely because the "not heating" symptom leads to different parts depending on the dryer type. A thermal fuse doesn't blow for no reason—if it's burned out, we look for the cause of overheating, otherwise the new one will burn out again.

Water leaks, noise, and vibration

We check for water on the floor at three points—the condensate drain pump, the hoses, and the condensate tank—and we divide noise and vibration into drum bearing issues and a simple leveling problem. The pump moves moisture to the tank or drain, and if it's clogged or the impeller is worn, water ends up on the floor. A crack in a hose or an overfilled tank causes a leak even with a working pump. A drum bearing hums and howls at high speeds, and over time shaft play adds to the sound. Worn rollers cause a rhythmic thumping, and a stretched belt causes slipping. An uneven floor and loose feet turn vibration into the cabinet "jumping," and a coin or bra wire in the drum knocks with every revolution. If the machine only "jumps" during the spin cycle and stands unevenly, that's not a breakdown but an installation issue; replacing the bearing in that case is premature.

What the error code on the display means

The combination of symbols on the screen is not a verdict but a hint: the board is telling you which part it's monitoring. The interpretation depends on the brand, but the general logic is the same—from the symbol to a group of parts and then to a specific component.

How to read an error code without the manual at hand

We interpret the code using the service documentation for the specific brand, not a universal table—the same symbols on Bosch, LG, and Samsung mean different parts. The control module detects a deviation from normal in the temperature sensor, moisture sensor, or heating circuit and assigns a combination tied to the model's firmware. The same combination on two machines from the same manufacturer but different series can lead to different chains: on the first it's the temperature sensor, on the second it's the wiring to the heating element. That's why we check the symbol against the service card for the series, not an internet table. Resetting the code with a button is not a repair: if the cause remains, the error will return after the first drying cycle.

The code points to a part, not a component

The code on the display usually points to a group—heating, moisture removal, sensors, or motor—and within that group the technician finds the specific part. The board doesn't distinguish what exactly failed: a burned-out heating element, a stuck thermostat, or a jammed pump all send a similar signal if they're on the same circuit. We check the drying chain in order: heating, airflow, drum rotation, moisture removal, sensor readings—and rule out components one by one until we find the real cause. The same symbol "not heating" can be caused by a burned-out heating element, a stuck thermostat, or a control board failure—so diagnostics go from the code to the component, not the other way around. This approach saves time and prevents replacing parts at random.

When an error code requires a technician

  • Heating error: don't start new cycles until a technician checks the heating element and the safety circuit.
  • Moisture removal error: check if the tank is full and the filter is clogged.
  • Repeating code: note the symbols and brand—this will speed up diagnostics.

Repair at home or at the service center

Most dryer breakdowns are fixed at the customer's address, but some work requires a service facility. The rule depends on the component, not the machine brand, and the technician determines it after inspection.

What is fixed at home and what requires service

  • Heating on-site: we replace the heating element, thermostat, and thermal fuse, checking the safety circuit before installation.
  • Mechanics on-site: we install the belt, rollers, and condensate pump, while assessing the bearing.
  • Maintenance on-site: we clean the heat exchanger and ducts—drying is restored without replacing components.
  • Control board at the service center: the module requires checking error codes and cycles at the service facility.
  • Bearing at the service center: the work involves full disassembly of the housing, so we take the machine to the facility.
  • Decision after inspection: the technician determines the place of work based on the actual situation, not on a phone description.

Table of repair options by component

WorkWhere we perform itWhat we checkNote
Replacing heating element and thermostatAt homeHeating and safety circuitThe cause of overheating is found before replacement
Cleaning heat exchangerAt homeAirflow and moisture removalRestores drying without replacing components
Replacing belt and rollersAt homeDrum rotationWe check bearing wear
Replacing condensate pumpAt homeMoisture removalWe check hoses for clogs
Repairing control boardAt service centerError codes and cyclesRequires testing at the service facility
Replacing drum bearingAt service centerDrum noise and playRequires full disassembly

How free diagnostics works

Our diagnostics are free: the technician checks the drying chain—heating, airflow, and moisture removal—identifies the cause and the cost of work, and service begins only after approval. The inspection distinguishes a clogged heat exchanger from a failing heating element: from the outside, both breakdowns look the same—the laundry stays damp. The specialist checks components one by one rather than replacing parts at random. In the city, our visit takes 60 minutes. The cost is quoted before work begins—if after diagnostics you decide not to proceed, you don't pay for the inspection. The technician explains in advance which components will be checked and why they are responsible for the symptom you reported. This conversation helps you understand the plan and avoid agreeing to replace parts blindly.

How repairing a heat pump machine differs from a condenser dryer

The type of drying determines which components are present in the machine, so diagnosing "not heating" in a condenser model and in a heat pump follows different paths.

How heating works in a condenser dryer

In a condenser dryer, the air is heated by a heating element, and moisture condenses in the heat exchanger and drains into the tank or drain hose—so "not heating" here almost always means the heater, thermostat, or thermal fuse. The coil sits in the duct behind the drum, the thermostat reads the air temperature, and the thermal fuse breaks the circuit on overheating and doesn't reset. The condenser tank or drain hose collects water after the heat exchanger, where steam turns into liquid. The power of such a heating element is usually between 1.8 and 2.5 kW, so a break in the power circuit shows up immediately and noticeably. If the heater is intact but there's no heat, check the control circuit and thermal fuse—the element itself is fine, and replacing a working part won't help.

How heating works in a heat pump dryer

In a heat pump dryer, the air is heated by a compressor with a refrigerant circuit, not a coil, so "not heating" here means checking the compressor, evaporator, and condenser. The refrigerant circulates in a closed loop: the evaporator takes heat from the drum air, the compressor compresses the gas and raises its temperature, and the condenser releases the energy back into the airflow. There's no separate heating element in this design at all. The heat pump runs at a lower temperature—around 50–60 degrees versus 120–150 for a heating element—so its failure rarely smells burnt and more often shows up as long drying times rather than an immediate breakdown. That's why owners delay calling a technician until the laundry stops drying completely, and by then the compressor may already be damaged.

Why this changes diagnostics and the scope of work

  • Condenser dryer: we check the heating element, thermostat, and thermal fuse by testing the circuit for continuity.
  • Heat pump dryer: we check the compressor, evaporator, and condenser, assessing the refrigerant pressure.
  • Common: in both cases, we check airflow and sensors before replacing parts.
  • Common mistake: a washing machine technician looks for a heating element where there isn't one—in a heat pump design, that component doesn't exist.

Which brands and models we service

Dryers from different brands are built differently, but the repair logic is the same. For a technician, the type of machine and parts availability matter more than the logo on the door.

Freestanding and washer-dryer combos

We service both freestanding dryers and washer-dryer combos—in the latter case, we fix the drying function specifically, without touching the washing unless necessary. In a combo machine, drying and washing share the drum and condensate pump, so a drying failure sometimes means checking the washing circuit too. In freestanding models, the setup is simpler: heater, fan, humidity and temperature sensors, drain pump. The technician first checks which cycle is failing—spin, water fill, or hot air blow. In combo units, drying often suffers because of a clog in the condensate path that also serves the wash cycle. Keep this connection in mind during diagnostics: checking both circuits is cheaper than a return visit.

Heat pump machines and premium brands

We service heat pump machines, including premium models: our technicians have 4 to 20 years of experience and work with refrigerant circuits, not just heating elements. In such a machine, drying is done by the compressor and heat exchangers, so diagnostics start with checking the circuit pressure and compressor operation. Premium brands often require original parts, and the technician first checks the component and only then says what needs replacing. The heat pump is sensitive to dirty filters and heat exchanger: a lint-clogged circuit overloads the compressor and reduces drying quality. On premium models, we match the part number with the manufacturer's catalog to avoid installing an incompatible analog. This approach saves you money—you don't pay to replace a component that still works.

Discontinued models

  • Diagnostics: even if the model is discontinued, we still take it on — first we identify which component has failed and whether a compatible replacement part is available.
  • Selection: we find a suitable part or a way to restore the component for your specific model, including non-standard items.
  • Decision: we quote the price and agree on the work before starting the repair, so you know the plan in advance.

What you can check yourself before the technician arrives

Some checks are safe and help the specialist find the cause faster, but there are things you shouldn't do yourself to avoid making the breakdown worse.

Safe checks before calling a technician

  • Lint filter: remove it, clean off the lint, rinse and dry before putting it back.
  • Condensation tank: drain the water and check if it's overflowing.
  • Installation: make sure the machine stands level and doesn't wobble on its feet.
  • Door: check that the door closes tightly and the lock isn't clogged with lint.
  • Drain hose: inspect for kinks and blockages if the machine is plumbed directly into the drain.

The door won't open after drying

If the door won't open, let the machine cool down first and check if the child lock is still active — don't force the door. The door lock keeps it locked while residual heat remains inside or until the control module releases the signal after the cycle. Yanking it at that moment breaks not the lock itself but the handle and hinge, adding mechanical damage to the electronics fault. Check if the lock latch is clogged with lint and disable the child lock according to your model's instructions. Our dryer technician on site checks the door lock and its power circuit to distinguish a stuck mechanism from a control board failure. If the door is still locked after cooling and disabling the lock, don't pry it with a knife — call a specialist.

Prevention that reduces the risk of repeat breakdowns

We recommend cleaning the lint filter after every drying cycle and regularly cleaning the heat exchanger and moisture ducts so the machine doesn't lose airflow. Lint settled on the heat exchanger of a condenser model acts like a blanket: air passes worse, heating runs longer, and the component wears out faster. In heat pump machines, a clogged heat exchanger also reduces compressor efficiency. Cleaning the heat exchanger and moisture ducts restores normal drying where the owner was already preparing to replace the heater. Maintenance every few months costs less than restoring a component damaged by overheating — and extends the life of the heating element. Note when you last cleaned the filter: this helps the technician rule out simple causes faster during diagnostics.

Warranty and how to tell a dryer specialist from a generalist

Choosing a contractor is about trust: who exactly will come, what happens with the warranty, and how they'll verify that the cause is fixed rather than masked by replacing a component.

1-year warranty on labor and parts

We provide a 1-year warranty on labor and parts: if after service the machine stops drying again for the same reason, we sort it out under warranty. The condition covers both replaced parts and performed operations — from replacing the heating element to cleaning the air duct. Hidden defects usually show up within this period. The warranty on parts is just as important as the warranty on labor — a faulty part doesn't show up immediately but after several cycles. That's why on a repeat call our specialist first compares the symptom with the previous repair instead of starting diagnostics from scratch: this way it's clear whether the old defect returned or a new one appeared. This is what distinguishes a proper service from a one-off job. A dryer repair technician who stands behind the result is motivated to see it through, not just swap a component.

How to tell a dryer specialist from a generalist

A dryer technician needs to know the difference between dryer types and where the heating element is versus where the heat pump is. A generalist who only fixes washing machines often looks for the wrong component. In a condenser dryer, heating comes from a heating element; in a heat pump model, the compressor and heat exchanger do the work, and you need to check completely different parts. Our technicians have 4 to 20 years of experience, and they've worked with both setups. Ask the technician how they check the drying chain — their answer about heating, airflow, condensate drainage, and sensors immediately shows their level: a real specialist lists the sequence of checks, not just one part at random. If all you hear is 'we'll replace the heating element' without any mention of the dryer type, be wary — on a heat pump machine, that diagnosis sends you down the wrong path.

Direct technician and you can pay via Kaspi QR, Kaspi Red, bank card, cash or bank transfer for companies

  • Our own technician: a service employee arrives, not a contractor from a directory, so the service center itself stands behind the result and the warranty.
  • Citywide visits: a technician reaches you within 60 minutes anywhere in the city.
  • Payment: we accept Kaspi QR, Kaspi Red, bank card, cash or bank transfer.
  • Cost: the technician quotes it after free diagnostics, before any work begins.

Tumble dryer repair what you should know

We've gathered in one place what determines the outcome of a dryer repair: what to look for when choosing a technician and what to check after the work is done.

  • The symptom points to the component: 'not heating,' 'not drying,' 'leaking,' and 'noisy' point to different parts of the drying chain, and you should start with the cause, not with replacing parts.
  • An error code is a hint, not a verdict: the meaning depends on the brand, and resetting the code without fixing the cause brings the error back after the first cycle.
  • The dryer type changes the approach: on a condenser model, check the heating element and thermostat; on a heat pump unit, check the compressor and refrigerant circuit.
  • Where the work happens depends on the component: most work is done at your home, but the control board and drum bearing require a service center.
  • Warranty and maintenance: a 1-year warranty on labor and parts plus regular cleaning of the filter and heat exchanger reduce the risk of repeat breakdowns.

21brands

Which clothes dryer brands we repair in Almaty

Our technicians work with these brands and source parts by model or part number.

We also repairWe also repairTECH SERVICE09

Besides clothes dryer repair, we fix other equipment in Almaty

Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.

BlogBlogTECH SERVICE10

Worth reading before clothes dryer repair in Almaty

Leave a review

Choose a platform — the TECH SERVICE page will open.

2ГИС2GISGoogle MapsЯYandex Maps
Send a review with photos on WhatsApp