Open until 19:00+7 (778) 746 00 26Call a technician
Tech Service technician next to a refrigerator

Centek Refrigerator Repair in Almaty

A technician arrives within 60 minutes anywhere in the city. Diagnostics are free — the technician will identify the problem and give you the cost.

  • 1-year warranty on labor and parts
  • Free diagnostics
  • Technicians with

Our own technicians4 to 20 years of experience

Ruslan Ts.Dilmurat S.Nikita M.Damir M.

Repair prices

  • Diagnostics0 ₸
  • Drain line cleaningfrom5 000 ₸
  • Defrost timer / sensor replacementfrom6 000 ₸
  • Door rehanging / adjustmentfrom6 500 ₸
  • Door seal replacementfrom7 500 ₸
All prices
2ГИСЯours4,97 898 reviews
2GIS · Google · Yandex · order database
Common faultsCommon faultsTECH SERVICE02

Common Centek refrigerator faults in Almaty

Below are typical symptoms and likely causes. The technician will pinpoint the exact cause during a free diagnostic.

PricesPricesTECH SERVICE03

How much Centek refrigerator repair costs in Almaty

The table shows prices for Centek refrigerator repair in Almaty: labor cost "from" (parts not included) and the timeframe; the technician confirms the final amount before starting the repair.

Drain line cleaninglabour only

1–2 hours

from5 000 ₸

Defrost timer / sensor replacementparts not included

1–2 hours

from6 000 ₸

Door rehanging / adjustmentlabour only

1–2 hours

from6 500 ₸

Door seal replacementparts not included

1–2 hours

from7 500 ₸

Filter drier replacementrefrigerant not included

1–2 hours

from7 500 ₸

Before and afterBefore and afterTECH SERVICE04

Before and after Centek refrigerator repair in Almaty

Door Misalignment and Poor Seal

1 visittime

from 6 500 ₸cost

Problem
The Centek refrigerator's door was misaligned and would not close fully, the gasket did not seal, and frost appeared in the compartment.
What we did
The technician tightened and adjusted the hinges, aligned the doors with the body, and checked the gasket seal.
Result
The door closes tightly, the gasket seals around the entire perimeter, and frost no longer appears in the compartment.
I want the same
Two-compartment refrigerator in a kitchen with doors open, a technician in an orange shirt crouched down tightening the middle door hinge with a screwdriverBeforeAfter
01 / 05
All repairs
TECH SERVICE mobile technician with a tool case

How Centek refrigerator repair works at your home in Almaty

Five steps from request to checking the work after repair.

  1. Requestsame day

    Submit a request by phone or WhatsApp. A technician arrives within 60 minutes anywhere in the city.

  2. Diagnosticsfree

    The technician arrives at the agreed time; you provide access to the refrigerator and the back wall.

  3. Approvalbefore work starts

    You approve the list of work and the cost. The technician starts after approval.

  4. Repairafter approval

    Some components are replaced on site; others require the unit to be taken away. A typical visit takes about an hour.

  5. Paymentafter check

    You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies. Ask the technician about payment options.

Leave a request
TechniciansTechniciansTECH SERVICE05

Our Centek refrigerator repair technicians in Almaty

The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

  • 8 technicians in Almaty
  • 8–12 years of experience in the department
  • Article author Ruslan Ts., 9 years of experience
Technician repairing a refrigerator at a customer’s home
Field technician at a customer’s home

The department has 8 specializations — they are listed on the technicians' cards.

01 / 05
Ruslan Ts., washing machine and refrigerator repair technicianexperience9 years

Ruslan Ts.

Washing machine and refrigerator repair technician

Dilmurat S., field technician for washing machine and refrigerator repairexperience10 years

Dilmurat S.

Field technician for washing machine and refrigerator repair

Nikita M., field refrigerator repair technicianexperience8 years

Nikita M.

Field refrigerator repair technician

Damir M., general household appliance repair technicianexperience12 years

Damir M.

General household appliance repair technician

Dima, expert washing machine repair technicianexperience8 years

Dima

Expert washing machine repair technician

We reply during working hours

Book Centek refrigerator repair in Almaty

Call or message us on WhatsApp and choose a convenient time for the technician to visit.

TECH SERVICE administrator replying to a customer's WhatsApp message

Warranty question? Call us

+7 (778) 746 00 26
Customer reviewsReviewsTECH SERVICE06

Reviews of Centek refrigerator repair in Almaty

Асель Ж.Order No. 2026-4630 · 5 February 2026

ours

Долго искал, кому это отдать, и вот нашёл. Повод для визита: намерзает лёд. Никита М объяснил причину так, что понял даже я. Сказали 32 500, я согласился без торга. Диагностику сделали бесплатно, хотя я был готов платить. В списке работ — уплотнитель. Рекомендую. Проверили при мне, показали, что всё держит

Repair: refrigerator

Мадина Т.Order No. TS-7219 · 28 November 2024

ours

Хотел сначала вызвать мастера на дом, потом передумал. Нужен был ремонт холодильника — обратился сюда. С чем пришёл: шумит. Сказали 27 000, а потом ещё и скидку сделали. Приехал вечером, мастер ещё был на месте. Заодно поменяли: термостат. В помещении тесновато, но это мелочи. Внешне как новый, если не считать мелкой царапины!!

Repair: refrigerator

Индира П.Order No. ZK-1617 · 20 September 2024

ours

Хотел сначала вызвать мастера на дом, потом передумал. Техсервис на Абая, если не ошибаюсь, — вот туда и поехал. Проверили на всех режимах, всё чётко!!

Repair: refrigerator

Лилия В.Order No. TS-4770 · 30 May 2024

ours

Работаю допоздна, поэтому нужен был сервис с нормальным графиком. Основная жалоба — намерзает лёд. Проверили при мне, показали, что всё держит.

Repair: refrigerator

Аружан К.Order No. ZK-2416 · 24 February 2023

ours

До этого обращался в другой сервис, там только развели руками. Проблема — не морозит. Проверили при мне, показали, что всё держит.

Repair: refrigerator

Алексей Г.Order No. TS-4782 · 30 August 2021

ours

Было подозрение, что дело в плате, хотелось услышать второе мнение. Приехал из командировки, а дома — шумит. В списке работ — уплотнитель. Проверил дома — всё на месте, ничего не забыли

Repair: refrigerator

Аяна Е.Order No. 25364 · 9 December 2017

ours

Отдал мастеру: холодильник. Жалоба простая: шумит. Никита М объяснил причину так, что понял даже я. Смета совпала с итогом, что редкость. Поставили новую деталь: термостат. Мастер сразу сказал, что к чему, без размытых формулировок. Нагрев в норме, посторонних звуков нет.

Repair: refrigerator

Станислав К.Order No. TS-3337 · 28 February 2017

ours

Повод для визита: шумит. Дильмурат С всё объяснил и не пытался впарить лишнее. Уже полгода — ни одного сбоя.

Repair: refrigerator

Сергей Р.Order No. ZK-8150 · 20 March 2016

ours

Хотел сначала вызвать мастера на дом, потом передумал. Нужен был ремонт холодильника — обратился сюда. Основная жалоба — шумит. Всё оформили по договору, с печатью. Заодно поменяли: термостат. Вышло 34 500 тенге, дешевле, чем я рассчитывал. Однозначно да. Проверил дома — всё на месте, ничего не забыли.

Repair: refrigerator

Евгений М.Order No. TS-5582 · 15 February 2016

ours

Долго откладывал ремонт, потом всё-таки собрался. Привёз на диагностику: холодильник. С чем пришёл: намерзает лёд. Ни копейки сверху, как и обещали. Разобрали, посмотрели: уплотнитель. Приняли без очереди, оформили за пять минут. Хороший сервис, побольше бы таких. Крутит ровно, без рывков

Repair: refrigerator
See all reviews
Questions and answersQuestionsTECH SERVICE07

Questions about Centek refrigerator repair in Almaty

Didn’t find the answer? Message us on WhatsApp.

Ask a question
How much do they pay for an old Centek refrigerator?

The amount depends on the condition, year of manufacture, and model of the Centek, as well as the terms of the buyback. There's no one-size-fits-all number, so check with a specific buyer or a service center that accepts old appliances.

Can a Centek refrigerator with a faulty compressor be repaired, or is it easier to buy a new one?

Replacing the compressor in a Centek is possible, but the decision depends on the model and the condition of the unit. After a free diagnostic, the technician will tell you whether the repair is worth it, considering the cost of the part and the overall condition of the refrigerator.

How can I check that the technician actually fixed the Centek refrigerator and didn't just reset the error?

After the repair, ask the technician to show that the refrigerator is cooling and running without issues. The error should not reappear, and the temperature in the compartments should match the set value.

Why does the Centek refrigerator not turn off and ice builds up?

If the Centek runs nonstop and gets covered in ice, the cause is often a faulty thermostat, defrost sensor, or refrigerant leak. The exact diagnosis depends on the model and is made after a technician's inspection.

What should I do if water leaks inside or under the Centek refrigerator?

Water inside or under the refrigerator usually appears due to a clogged drain or a displaced drain tube. Check if the hole is blocked, but it's better to call a technician to fix it.

Will a Centek refrigerator technician come to my home, or do I need to take the appliance to the service center?

The technician comes to your home anywhere in the city, and the visit takes about 60 minutes after your request. Most Centek repairs are done on-site, and the appliance is taken to the service center only for complex unit repairs, depending on the model.

Repair guideArticleTECH SERVICE08

Centek Refrigerator Repair in Almaty with On-Site Technician

Ruslan Ts., washing machine and refrigerator repair technician

Author: Ruslan Ts.,Washing machine and refrigerator repair technician

Published
Updated

Tech Service repairs Centek refrigerators in Almaty at home or at the service center: our technician arrives within 60 minutes anywhere in the city, diagnostics are free, and there is a 1-year warranty on labor and parts. The technician provides the price after diagnostics, and you can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies.

Why Your Centek Refrigerator Isn't Cooling and What Its Error Codes Mean

Most often, a Centek refrigerator "goes quiet" in two ways: it stops cooling while the light inside stays on, or it shows a code on the display. Let's break down what that means and how we check it.

Why Centek Isn't Cooling Even Though the Light Is On

We start by checking the compressor and the refrigeration circuit, because a burning light only means the lighting circuit works, not that cooling does. The motor-compressor may start and even hum, but if the pressure in the circuit doesn't rise, no cold is produced. The cause is more often a refrigerant leak at the joints or a clogged capillary tube where the freon stops circulating. Our job at this step is to find the freon leak and make sure the compressor builds the required pressure, not to replace parts based on a guess. A humming motor with warm compartments almost always means a circuit problem, so the technician looks for the leak and checks the entire system rather than swapping parts at random. This approach saves the owner money: replacing a working compressor wouldn't bring the cold back. If you need Centek refrigerator repair in Almaty, the technician comes to your home and checks the circuit on site.

What the Error Codes on the Centek Display Mean

A code on the Centek display points to a specific component — a temperature sensor, the defrost circuit, or the control board — and we decode it before starting work. A thermistor may output incorrect resistance, so the controller "thinks" the compartment is already cold and doesn't turn on the compressor. The defrost heater and its circuit give their own code when the No Frost system doesn't exit the defrost cycle and the evaporator ices up. The control board reports an error if it doesn't receive a signal from the sensor or the compressor relay. Pressing a button to reset the error isn't enough: if the sensor or defrost heater is faulty, the code will return after the first cycle, so the technician checks the component itself, not just the indication. The indication is only a hint where to look, not a ready diagnosis.

How We Check a Centek Refrigerator During Diagnostics

  • Compressor and pressure: the technician measures the motor-compressor operation and the pressure in the circuit to tell a freon leak from a clogged capillary tube.
  • Refrigeration circuit: we inspect joints and connections for refrigerant leaks and check freon circulation throughout the system.
  • Defrost circuit: we test the heater, sensor, and defrost timer — on No Frost, this is where the cause of ice buildup most often hides.
  • Electronics: we check the control board and thermistors, comparing readings with the Centek error code descriptions.
  • Diagnostics result: the technician names the cause and the cost of work after inspecting the components, and the diagnostics itself is free. It's normal to ask to see the component test results: they show that the cause is being fixed, not just the symptom.

Typical Centek Failures from Symptom to Cause

Every Centek failure has a recognizable symptom. Below is how it shows up, what usually causes it, and what the specialist does on site.

Centek Clicks and Won't Start

Clicking without starting most often points to the start relay or the compressor, and we begin with the start circuit. The start relay is responsible for starting the compressor: when its contacts are worn, it clicks but doesn't supply voltage to the winding. On site, we test the relay, try starting the motor, and measure winding resistance — these measurements show where the circuit is broken. If the start component is working but the motor won't start, the cause lies in the compressor itself or in the control board's power supply. In such cases, Centek refrigerator repair starts with checking the start circuit. Repeated attempts to turn it on while it clicks only load the winding — better not to pull the plug from the socket and wait for a specialist. This approach keeps the compressor alive until the technician arrives.

Ice Builds Up and Water Leaks into the Compartment

In Centek No Frost models, ice buildup is usually caused by the defrost circuit, while water inside the compartment points to a clogged drain. We check both. The defrost heater, defrost timer, and evaporator fan are responsible for defrosting: if one of these components fails, frost accumulates on the evaporator and cold air stops circulating between compartments. A clogged drain tube causes leaks inside: condensate doesn't drain into the pan and pools under the drawers. We test the defrost circuit for continuity and blow out the drain along its entire length. A clogged tube isn't always visible from the outside: moisture can drain into the pan and appear under the drawers, so we inspect the entire drain, not just the visible opening. When a customer reports water inside, the technician checks the drain first.

Centek hums and won't shut off

If a Centek hums nonstop, we check the thermostat and temperature sensor: the compressor runs continuously when it doesn't receive a signal that cooling is needed. The thermostat in direct-cool models and the temperature sensor in No Frost systems close the circuit when the desired temperature is reached—when they fail, the motor doesn't get the command to stop. Our technician measures the temperature in the compartments, compares it with the setpoint, and tests the sensor for continuity. If the thermostat is fine, we check for refrigerant leaks and test the compressor under load. Continuous operation accelerates wear, so it's best not to delay diagnostics even if cooling seems fine. Calling early saves the life of a component that's harder and more expensive to replace than a relay. If the motor runs nonstop, the load on the windings and capacitor increases every hour, so the technician checks the unit before the failure becomes irreversible.

How Centek's design affects repairs

Centek refrigerators come with different cooling systems, and that determines which components fail and how repairs are done. Let's look at how diagnostics differ for No Frost and direct-cool models, and why budget construction changes the technician's approach.

No Frost vs. direct cool: what's different for diagnostics

Cooling systemWhat we check most oftenTypical symptom
No FrostDefrost circuit, evaporator fanIce buildup, noise
Direct CoolDrain, door sealWater inside, frost on the wall
Both systemsCompressor motor, circuit, electronicsNot cooling, error codes

Why Centek's budget components fail differently

Centek is a budget brand, so some components are designed for a shorter lifespan, and that changes the diagnostic approach. The motor here has a thinner safety margin, and the plastic evaporator parts and fasteners lose their shape faster with temperature changes. Parts for Centek are available, but you need to match them to the exact model: within one series, different motors and boards can be used. When a cheap component fails, the technician first assesses the condition of nearby parts: replacing just one part in a worn-out system is often not worth it. Checking the whole circuit at once is more cost-effective than coming back to it later. That's why when servicing Centek refrigerators, we look not only at the failed component but also at what works around it.

Inverter compressor in the Centek lineup

If a Centek model has an inverter compressor, diagnostics start with the control board, because it sets the operating mode. The inverter changes speed smoothly, and if the electronics fail, the unit either won't start at all or runs at a single speed—from the outside, it looks like it's not cooling. We check the control board of the Centek refrigerator for blown power switches and sensor condition, and only then draw conclusions about the compressor itself. An inverter compressor rarely fails on its own but is sensitive to electronics faults—so the board should be checked before replacing the compressor. Diagnostics are free, and there's a 1-year warranty on labor and parts.

Is it worth repairing a budget Centek?

For Centek, the question "repair or buy new" isn't about price — it's about which component failed and how much life the rest have left. Let's look at three scenarios we see most often on service calls.

When repairing a Centek makes sense

  • Isolated failure: the start relay, thermostat, or temperature sensor can be replaced individually without opening the refrigerant circuit.
  • Compressor still running: if the motor starts and holds pressure, replacing one inexpensive part can add years to the fridge's life.
  • Gasket and drainage: a worn rubber seal or a clogged drain line can be fixed quickly and restore proper cooling in the compartments.
  • Condition of other components: if the circuit is working and the control board is intact, investing in the Centek pays off.
  • Our experience: we replace compressors, thermostats, and start relays — after free diagnostics, the technician explains the scope of work for each component.

When repair may not be worth it

If the compressor fails along with the circuit or the control board, restoring a budget Centek can cost about the same as buying a new fridge. The compressor is the key component of the refrigeration circuit, and replacing it involves soldering, vacuuming, and recharging with refrigerant. In budget models, the control board often comes as a single unit with the display and modes. Add general wear and tear: if the gasket no longer seals and the compartments are overloaded, investing in an old cabinet doesn't pay off. The decision should be made after diagnostics: the technician assesses not only the breakdown but also the condition of other components, so you don't put money into a worn-out fridge. Telling the owner upfront when repairs don't make sense saves them money.

How often do Centek refrigerators break down?

Centek fails no more often than other budget brands. The most common failures are the start relay, thermostat, sensors, and defrost circuit. The start relay is the most stressed element at every motor start; the thermostat and temperature sensor control the on/off cycle; and the defrost heater in No Frost systems is part of the defrost circuit and eventually burns out or gets covered in ice. Many breakdowns are not due to defects but to operating conditions — overloaded compartments, worn gaskets, infrequent defrosting. A fridge that is defrosted according to the manual and not packed to the brim lasts noticeably longer. Practice shows that Centek fails in the same components as any budget appliance — it's not about the brand but about the load on a specific part.

How home repairs work and what the warranty covers

We work as a direct provider: our specialist comes to your home or takes the fridge to our service center, and the work process and warranty are transparent from the start.

How home repairs are done

  • Technician visit: we arrive within 60 minutes anywhere in the city — no more than an hour from request to inspection.
  • Free diagnostics: we check the compressor, thermostat, and sensors, measure the temperature in the compartments, and read the display codes.
  • Approval of work: we explain the cause of the breakdown and give you the price after diagnostics — before any work begins.
  • Repair at home or in the service center: some issues we fix on-site; others require work in the service center with disassembly of the unit.
  • Temperature test: we measure the cold in the compartments and compare the readings with the manufacturer's specs for your model.
  • Handover: if service is needed, we explain the reason before taking the fridge — you understand why the workshop is necessary.

What the warranty covers and for how long

We provide a 1-year warranty on labor and parts, and it covers both the replaced components and the work performed. The year covers both the service and the installed part — if a component fails due to our fault, we replace the work and the part under warranty. The technician records which component was replaced and what exactly was checked during the test control, so there are no disputes about the scope of work. The warranty only makes sense together with the check: we measure the temperature of the compartments to make sure the component is working normally, not just that it started up. Without such a measurement, the warranty becomes a formality — the breakdown is noticed later, when the food is already spoiled and the cause has had time to manifest in another component. That's why we perform test control before closing the job and compare the readings with the specifications for the specific Centek model.

Centek parts and how to check the result

We select parts for the specific Centek model and then check the result by the temperature of the compartments and the operation of the components. The compressor, thermostat, defrost sensor, and fan differ in mounting dimensions and connectors across different lines, so the part is selected by the marking on the nameplate, not by eye. Then the specialist reads the display and makes sure there are no new error codes and that cold is maintained in both compartments. You can check the result yourself: if after a few hours the compartments hold cold and no new codes appear on the display, the component is working correctly. If the code returns, it's a signal that the cause is deeper than the replaced part, and such a case should be shown to the technician again rather than waiting for the appliance to defrost again.

What to remember about Centek refrigerator repair

The bottom line on a Centek refrigerator comes down to a few practical points: from assessing a specific component to checking the result after the repair is done.

  • Component assessment: local faults in the relay, thermostat, or drainage are fixed, while compressor wear along with the circuit requires a separate decision.
  • Error code: the message on the display points to a specific component, but resetting the error without inspecting the part is pointless — it will come back.
  • Diagnostic logic: the cooling system sets the order of actions — in No Frost, check the defrost and fan; in a drip model, check the drainage and seal.
  • Repair decision: it is made after diagnostics, when the condition of all components is visible, not just the failed one.
  • Result check: stable compartment temperature and no new codes on the display confirm that the fault has been fixed.

90brands

Besides Centek, we repair other refrigerator brands in Almaty

We work with every brand sold in Kazakhstan — from Samsung, LG and Atlant to Biryusa, Indesit, Stinol and rare imported makes. Can’t find yours in the list? Call anyway — a technician will come and take a look.

We also repairWe also repairTECH SERVICE09

Besides Centek refrigerator repair, we fix other equipment in Almaty

Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.

BlogBlogTECH SERVICE10

Worth reading before Centek refrigerator repair in Almaty

Leave a review

Choose a platform — the TECH SERVICE page will open.

2ГИС2GISGoogle MapsЯYandex Maps
Send a review with photos on WhatsApp