experience9 yearsRuslan Ts.
Washing machine and refrigerator repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 021 13 16Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Free diagnostics, 1-year warranty on labor and parts.
Our own technicians4 to 20 years of experience




Repair prices
Below are typical symptoms and their likely causes. The technician will pinpoint the exact cause during free diagnostics.
Battery, button, power cord
from2 500 ₸
Clogged filter, motor
from1 500 ₸
Clog, loose connection
from3 000 ₸
Worn brushes, winding
from2 500 ₸
Worn cells, charger
from9 500 ₸
Tangled hair, wear, bearing
from2 500 ₸
Overheating, clogged filter, brushes
from1 500 ₸
Crack, clog, mount
from1 500 ₸
The table shows prices for Vivenso vacuum cleaner repair in Almaty: a starting labor cost without parts and the timeframe. The technician confirms the final total before any work begins.
1–2 hourstime
from 3 000 ₸cost

BeforeAfter5 steps

Five steps from the call to checking the vacuum cleaner's performance.
Leave a request and the technician will arrange a convenient visit time.
The technician will confirm the model and symptoms over the phone; have the vacuum cleaner and attachments ready.
The technician checks the power, battery, motor, suction, and attachments.
You approve the scope of work and the cost, then the technician gets started.
The technician turns the vacuum cleaner on with you and shows the result in all modes.
The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience12 yearsGeneral household appliance repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsExpert washing machine repair technician
experience8 yearsField refrigerator repair technician
experience8 yearsSenior washing machine repair technician
experience11 yearsDishwasher repair technician
experience9 yearsWashing machine repair technician
We reply during working hours
Describe the symptom and the technician will tell you what to check before the visit and which attachments to prepare.

Warranty question? Call us
+7 (778) 021 13 167 898 reviews of repairs at TECH SERVICE in total
Светлана Д.Order No. ZK-2025/235 · 20 August 2025
oursВыбирал по отзывам в 2ГИС, времени на эксперименты не было. Не люблю сервисы, но этот запомнил. Проблема — шумит. Рустем Т возился с этим дольше, чем планировал, но довёл до конца. Заявку приняли по телефону, перезвонили через десять минут. Запчасть была в наличии, доплачивать не пришлось. Починили и дали гарантию на месяц.
Даулет С.Order No. ZK-2025/381 · 23 April 2025
oursСмотрел, у кого есть запчасти на такую модель. Заодно поменяли: шланг. Ребёнок уже проверил на прочность, держиться
Алексей Г.Order No. 25570 · 13 November 2024
oursОсновная жалоба — не включается. Дамир М приехал в тот же день, хотя был конец смены. Нагрев в норме, посторонних звуков нет.
Ринат Х.Order No. 229820 · 10 February 2022
oursПробовал найти мастера в своём районе, но все были заняты. Нужен был ремонт пылесоса — обратился сюда. Повод для визита: шумит. Дамир М не стал навязывать дорогую запчасть, поставил нормальную. Запчасть была в наличии, доплачивать не пришлось. Мастер посмотрел, сказал, что возьмётся, и взялся. Гудит ровно, не греется, всё как надо.
Индира П.Order No. TS-7580 · 17 January 2021
oursИскал мастерскую поближе к дому, чтобы не мотатся с техникой через полгорода. Включил, проверил, работает
Индира П.Order No. TS-2004-259 · 19 August 2020
oursПрочитал кучу отзывов, половина — реклама, но тут вроде живые. Руки чесались починить самому, хорошо, что не полез. С чем пришёл: шумит. Сравнивал с двумя другими — здесь вышло ровнее всех. Разобрали, посмотрели: шланг. Выбирал между парой сервисов, Tech-service взял адекватностью. Шум пропал, работает мягко.
Ирина Т.Order No. 31352 · 20 July 2019
oursПробовал найти мастера в своём районе, но все были заняты. Проблема — шумит. Внешне как новый, если не считать мелкой царапины.
Максим Ю.Order No. TS-9450 · 31 August 2017
oursТехника на гарантии уже не была, так что выбор был свободный. Ещё утром всё работало, а к вечеру — не всасывает. В списке работ — шланг. Заплатил 12 000, и не жалею. Объяснили по телефону, что можно не везти, но я всё равно привёз. Крутит ровно, без рывков.
Гаухар Н.Order No. ZK-3383 · 23 April 2017
oursДамир М не стал навязывать дорогую запчасть, поставил нормальную. Заявку приняли по телефону, перезвонили через десять минут. Проверили при мне, показали, что всё держит.
Акбота Т.Order No. 16516 · 20 April 2016
oursҮйдегілер «лақтыр» деді, мен шешім қабылдамай тұрып көрсетуге апардым. Таңертең жұмыс істеп тұрды, кешке қарай үнсіз қалды
Didn’t find the answer? Message us on WhatsApp.
Ask a questionYes, we accept these models for repair. Most often, when there are problems with the water filter, the pump, tank seals, or contacts suffer after water gets in. A technician will check the wet cleaning system on site or at the service center.
If suction doesn't return after cleaning the filter and air path, and the motor hums strainedly or sparks, the problem is likely the motor. A free diagnostic will give an exact answer; the result depends on the model.
Yes, we check and fix battery or charging unit faults. A free diagnostic will show what exactly failed — the battery, contacts, or circuit board.
Yes, for tank cracks we select a replacement or restore watertightness if possible. The technician will suggest a specific solution after inspection; it depends on the model.
The cause could be worn motor bearings or a foreign object in the turbine. The technician will disassemble the unit and identify the source of the noise; it depends on the model.
We repair the control board rather than just replacing it: the technician looks for the faulty component and restores the circuit. If repair is impossible, we'll discuss replacing the unit; it depends on the model.
Tech Service repairs Vivenso vacuum cleaners in Almaty as a direct provider: our technician comes to your home or the repair is done at our service center. Diagnostics are free, technician arrival within 60 minutes across the city, and a 1-year warranty on labor and parts. The technician provides the cost after diagnostics.
A Vivenso vacuum is built like most household models, but the brand has its own weak points. Let's look at which components fail most often and what signs to spot before taking it apart.
Loss of suction in a Vivenso is usually caused by a clogged air duct or a dirty filter, not a motor failure. The airway gets clogged with lint and fine dust at the bends of the hose, at the entrance to the telescopic tube, and on the cyclone grille. An overfilled bag blocks the flow completely, and the HEPA cartridge loses throughput even from a thick layer of dust on the pleats. Less often the turbine is to blame: the impeller gets coated with carbon deposits, the blades lose their shape, and the motor spins the shaft without effect. You can check this without disassembly—remove the hose and tube, turn the unit on, and feel the suction at the inlet port: if it's back, the problem is in the airway, not the motor. This test takes a minute and immediately rules out half the possibilities.
A flashing indicator on a Vivenso signals a specific fault, not a general breakdown, so you need to decode it according to your model. On some versions the LED lights up for a clogged cartridge, on others for an overheated winding or a control board failure. Flashing with a pause usually points to a sensor, a steady light to a failed component, and a combination of two lights requires checking the manual for your specific unit. Spontaneous shutdown after a minute of operation is more often due to overheating protection—a clogged filter or blocked airway—rather than electronics. The control board is usually fine in such cases, and after cleaning the air path the unit holds power again. Note the sequence of lights before the technician arrives—it helps find the cause faster than disassembling blindly. This saves time for both the technician and the owner.
| Symptom | Likely cause | What the technician checks |
|---|---|---|
| Won't turn on | Switch, cable, board | Power circuit and button |
| Hums but no suction | Turbine, clog | Impeller and air duct |
| Louder than usual | Shaft bearings | Shaft play and wear |
| Smell during operation | Overheating, filter | Filter and motor winding |
| Shuts off after a minute | Overheat protection | Filter and airflow |
Water-filter models are built differently from bagged and cyclone ones: a separator divides water and dust, and suction depends on the tank's airtightness. Let's look at what to check first.
In Vivenso vacuums with water filtration, suction drops after washing due to an improperly assembled separator or misaligned seals, not the motor. We start by disassembling the unit: check whether the water filter separator sits evenly in its seat ring, whether the gasket is folded, and whether water remains in the channel between the dust tank and the motor. Often the owner tightens the lid until it clicks, but the ring is already deformed from hot water and doesn't fit tightly all around. Our technicians check the seals for elasticity and signs of crimping, and the tank seating for play and misalignment relative to the body. If water leaks into the motor compartment after assembly, suction will also drop—seals and tank seating are checked before turning on to avoid flooding the motor. Vivenso vacuum repair in Almaty in such cases begins with checking the water circuit's airtightness.
We replace a cracked plastic tank on a Vivenso with an aqua filter with a new one, because glue doesn't hold the vacuum and water gets into the housing. The tank operates under constant pressure differential, and any seam on it is a weak point: during suction the walls are pulled together, the crack opens up, and the water circuit stops being sealed. We inspect the bottom, the seating ring and the joint with the aqua filter separator, check the seals around the perimeter and at the lid joint. Vivenso vacuum cleaner service in Almaty often starts with this very part when the owner brings in a unit with loss of suction and traces of water under the tank. Even a small crack along the seam eventually spreads under load, so if there are chips on the seating ring, the part is replaced rather than repaired.
The work follows clear stages — from diagnostics to post-assembly testing. We'll show what the technician does at each step and which unit operations are most common.
We start with free diagnostics and fault detection of components, and finish with post-assembly testing. First, the technician checks suction, listens to the motor and looks at the indicators on the housing, then disassembles the unit indicated by the symptom: turbine, control board or container. After fault detection, he agrees the scope of work with you — which parts to replace and which to repair. Assembly goes in reverse order, and the final test repeats the initial check to make sure suction is back to normal and abnormal noise is gone. Fault detection is done before disassembling the motor — this way you don't have to replace working components and inflate the job with extra parts. Vivenso vacuum cleaner repair in Almaty follows exactly this scheme — from initial check to control test. A technician visit within the city takes up to 60 minutes, warranty on labor and parts is 1 year.
| Component | What we do | When indicated |
|---|---|---|
| Control board | Repair | Power failures, buttons not responding |
| Turbine | Replace as assembly | Impeller wear, loss of suction |
| Shaft bearings | Replace | Abnormal noise, play |
| Starting capacitor | Replace | Motor won't start |
| Battery | Replace | Doesn't hold charge |
For Vivenso vacuum cleaners, we select parts for the specific model, and for rare items we tell you in advance if the part will have to be ordered. The technician checks the HEPA filter and bag filter when suction is weak, inspects seals and gaskets for tightness, assesses wear of brushes and attachments. These items are consumables: they are replaced more often and are easier to source because they are not rigidly tied to the housing. Housing components like the dust tank are model-specific, so their availability is confirmed before work starts — otherwise service could drag on indefinitely. Our technicians have worked with this equipment for 4 to 20 years and can tell you right away by model number which parts are interchangeable and which are only for a specific modification. The control board is more often repaired, while bearings and capacitor are replaced — repairing these parts doesn't give a reliable result.
Both formats have their advantages. Let's look at when it's more convenient to call a technician and when it's better to bring the vacuum cleaner to the service center.
We make house calls throughout the city, and a technician arrives within 60 minutes, so for most Vivenso breakdowns, a specialist visit is more convenient. The technician handles clogs in the air duct, worn brushes, damaged hose and attachments, and stretched drive belt — all of this can be fixed on-site, without trips or waiting. We provide free diagnostics at the customer's location, and the owner immediately sees which component has stopped maintaining suction. Moreover, the check is done on your equipment with your hose and attachments, not on a test bench at the workshop. At home, it's easier to test the vacuum cleaner in familiar conditions — with the same hose and attachments that it's not picking up well with — and not wonder whether the symptom will repeat at the service center. You can pay via Kaspi QR, Kaspi Red (instalments), bank card, cash, or bank transfer for companies, and the 1-year warranty on labor and parts applies regardless of the format.
People bring a Vivenso vacuum cleaner to the service center when the motor needs to be disassembled or the control board needs to be restored — such work requires stationary conditions. The electric motor, commutator, and winding require careful disassembly of the unit and subsequent reassembly with testing, and there's no place to spread all this out in an apartment. The control board with error indicators also requires calm soldering and circuit testing with hands-on access, without haste and without foreign objects on the table. If the breakdown affects the electronics, it's not always possible to complete it in one visit on-site, so the technician warns in advance which work will be done at the service center. The 1-year warranty on labor and parts applies to either format, and the specialist quotes the price after free diagnostics — without this preliminary check, naming a sum would be guesswork.
| Criterion | At home | At the service center |
|---|---|---|
| Simple breakdowns | Convenient | Also possible |
| Electronics and motor | Limited | Full scope |
| Travel time | None | Need to bring it in |
| Testing in everyday use | Immediately | After return |
| Technician arrival | Within 60 minutes | — |
Before requesting service, it's important to understand what the cost consists of, what the warranty covers, and by what signs you can distinguish a specialist who truly knows the brand from one who takes on everything.
Diagnostics of a Vivenso vacuum cleaner is free with us, and the specialist quotes the cost of work after it, when the cause of the breakdown is clear. During the inspection, they check the suction at the inlet and outlet, listen to the motor, assess the condition of the filters, container, and seals, and test the control board and sensors. Based on the fault detection of components, they list which parts have failed and what work will be needed — without vague phrases like "we need to look inside." This procedure protects against unnecessary work: if after the inspection it turns out that the issue is a clog or a clogged filter, you won't have to pay for replacing components — the air duct will simply be cleaned and the suction rechecked. The technician also explains which component wore out first and what to watch for during the next cleaning to avoid a repeat breakdown. The owner leaves with a clear picture of the appliance's condition, not with guesses about what might have broken.
We provide a 1-year warranty on labor and parts, so if the same issue happens again after service, it's covered under that warranty. If the vacuum cleaner stops suctioning again or shows the same indicator, the technician checks the previous repair: the replaced motor, board, or tank seal remain our responsibility for a year. The warranty also covers the installed parts, so if you come back with the same problem, you won't be charged for the same work again—first we check whether the replaced component has failed. For you as the owner, this means a repeat visit for the same issue doesn't turn into a new cycle from scratch. The terms for labor and parts are explained before work begins, so there are no questions afterward.
Vivenso breakdowns usually come down to a few recurring scenarios: from a clogged airway to worn seals in the water filter. Below is a quick summary to help you understand the nature of the problem in advance.
60brands
We repair Vivenso vacuum cleaners and other brands that have dedicated pages on the site.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your dishwasher won't drain, the most common culprits are a clogged filter or drain hose; less often, it's the pump, impeller…
24 March 2026 · 12 minutes read
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
If your microwave isn't heating but the light and turntable still work, the problem is usually one of the high-voltage components — the magnetron, diode…
15 February 2026 · 12 minutes read
If your refrigerator stops working, first check the outlet, the power cord, and the thermostat setting, and after defrosting let it stand for a while.
4 February 2026 · 12 minutes read
Washing machine error codes are self-diagnostic codes that point to a specific component: drain, water fill, heating, motor, or door lock.
29 January 2026 · 13 minutes read












