experience9 yearsRuslan Ts.
Washing machine and refrigerator repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 021 13 16Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Free diagnostics, final price after inspection.
Our own technicians4 to 20 years of experience




Repair prices
Below are typical symptoms and likely causes. The technician will determine the exact cause during free diagnostics.
cord, plug, button, motor
from2 500 ₸
clog, filter, hose, turbo brush
from1 500 ₸
overheating, clog, motor wear
from2 500 ₸
bearing, impeller, foreign object
from3 000 ₸
retraction mechanism, spring
from2 500 ₸
plastic, latch
from1 500 ₸
belt, brushes, winding
from7 000 ₸
thermal protection, motor, board
from2 500 ₸
The table for Vitek vacuum cleaners shows the starting price for labor without parts and the time frame; the technician will agree on the total amount before starting repairs.
1–3 business daystime
from 8 000 ₸cost

BeforeAfter5 steps

Five steps from request to performance check.
Leave a request, describe the symptom and the vacuum cleaner model.
The technician arrives anywhere in the city within 60 minutes after the request.
The technician records the list of work in the request; clarify what is included in the scope and which parts are needed.
You agree on the scope of work and cost, then the technician starts.
We check the vacuum cleaner's operation. 1-year warranty on labor and parts.
The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience12 yearsGeneral household appliance repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsExpert washing machine repair technician
experience8 yearsField refrigerator repair technician
experience8 yearsSenior washing machine repair technician
experience11 yearsDishwasher repair technician
experience9 yearsWashing machine repair technician
We reply during working hours
Tell us the vacuum cleaner model and symptom, clear space near a power outlet for inspection, and have the attachments ready.

Warranty question? Call us
+7 (778) 021 13 167 898 reviews of repairs at TECH SERVICE in total
Ержан А.Order No. ZK-5205 · 17 April 2025
oursВыбирал по отзывам в 2ГИС, времени на эксперименты не было. Больше всего напрягало: не включается. Tech-service оказался ближе всех, за это и выбрал. Крутит ровно, без рывков.
Анна Т.Order No. ZK-3408 · 18 May 2024
oursБыло важно, чтобы сделали до выходных — гости, то-сё. Повод для визита: не включается. Вернули в тот же день, всё функционирует.
Аскар Ж.Order No. 35488 · 29 March 2024
oursДо этого обращался в другой сервис, там только развели руками. Проблема — не всасывает. Техсервис в Алматы, если что, вот их адрес — не пожалел. Сказать, что доволен — ничего не сказать.
Андрей П.Order No. TS-4997 · 28 December 2023
oursХотел сначала вызвать мастера на дом, потом передумал. Запчасть была в наличии, доплачивать не пришлось. Уже полгода — ни одного сбоя.
Сауле Н.Order No. ZK-2022/567 · 17 August 2022
oursБыло подозрение, что дело в плате, хотелось услышать второе мнение. Вечером включил — и всё стало ясно: не включаеться. Позвонили заранее, предупредили, что задержится на полчаса. Вышло дешевле нового, что логично. Заодно поменяли: шланг. Не пожалел ни разу. Сделали и забыл про проблему
Бакыт Ж.Order No. 2022-8882 · 15 August 2022
oursТехниканы жөндеуге алып келу үшін арнайы уақыт бөлдім. Күтуге уақытым жоқ еді, сол күні алып кеттім. Бәрі жақсы, шағымаймын.
Фарида К.Order No. ZK-2021/650 · 17 December 2021
oursВыбирал по отзывам в 2ГИС, времени на эксперименты не было. Привёз на диагностику: пылесос. Проблема — шумит. Дамир М не стал навязывать дорогую запчасть, поставил нормальную. По деньгам вышло адекватно, в другом месте просили больше. Мастер показал, что меняет: шланг. Мастер посмотрел, сказал, что возьмётся, и взялся. Если что — обращусь снова. Сделали и забыл про проблему.
Гульмира С.Order No. TS-1707-240 · 20 May 2017
oursПоломка застала перед командировкой, тянуть было нельзя. С чем пришёл: не всасывает. Шум пропал, работает мягко.
Ляззат К.Order No. 133246 · 28 January 2017
oursС чем пришёл: не включается. Рустем Т снял деталь, показал износ, вопросов не осталось. Вернули в тот же день, всё функционирует!!
Ерасыл Б.Order No. ZK-2016/473 · 10 December 2016
oursДолго откладывал ремонт, потом всё-таки собрался. Первое, что заметил: не всасывает. Проверил дома — всё на месте, ничего не забыли)
Didn’t find the answer? Message us on WhatsApp.
Ask a questionUsually a Vitek turbo brush can be repaired: the belt or bearing is replaced, or the connector contact is restored. The whole assembly is replaced less often, when the housing or shaft is cracked, and that becomes clear after disassembly.
Most often the battery itself is to blame: it loses capacity over time and with cycles. But a faulty charging board can behave the same way, so free diagnostics gives the exact answer.
That means the cause isn't the filter: there may be a clog in the hose or tube, worn motor brushes, or air leaks at the connections. A technician can check this during an inspection and identify the culprit.
With a clogged filter, suction drops gradually, while a burned-out motor often gives a burning smell, a whining noise, or a complete failure to turn on. It depends on the model, so diagnostics makes the final call.
Yes, we repair Vitek wet/dry vacuums. They also require checking the pump, tank, and wet cleaning system, so there's usually more work than with dry models.
This is often how overheating protection or a faulty control board behaves. Free diagnostics will show the exact cause, which a technician will perform after you submit a request.
Tech Service repairs Vitek vacuum cleaners in Almaty as a direct provider, with no middlemen. Our technician arrives at your home within 60 minutes anywhere in the city or accepts the appliance at our service center. Diagnostics are free, we give you the price after diagnostics, and we provide a 1-year warranty on labor and parts.
A symptom is a consequence, and the cause is almost always in a specific component. Let's look at what most often fails in Vitek and how to recognize the problem before the technician arrives.
Most often, power is lost due to worn graphite brushes in the motor, a break in the cord, or a triggered protection on the control board. Graphite brushes wear down to their limit and stop touching the commutator — the motor won't start even though the button works. A break in the power cord usually occurs at the base of the plug and where the cable enters the body, as it constantly bends there. The control board in models with electronic power control shuts off the unit during overload or a short circuit in the winding. The power switch fails less often than the above — its contacts burn out during frequent starts under load. If the vacuum cleaner turns on for a couple of seconds and then goes off, it's almost always the board's protection, not the switch — don't disassemble the body until a technician checks the power. If your own check doesn't help, Vitek vacuum cleaner repair in Almaty is performed by a technician after free diagnostics.
Loss of suction in Vitek follows the chain filter → hose → turbine → motor, and usually it's not just one component but a clogged HEPA filter along with a crack in the hose. Fine dust clogs it within a few months and blocks airflow, while the foam pre-filter lets larger debris through if not washed. A crack in the hose or a loose fit of the pipe causes air leakage — the motor runs idle and suction at the nozzle drops. The turbine loses efficiency when dust sticks to the blades, and the container when overfilled above the mark. If suction doesn't return after cleaning the HEPA filter, check the container fit and the integrity of the pipe — air leaks at joints have the same effect as a clogged filter.
Overheating and a burnt smell in Vitek are caused by a clogged filter, worn motor bearings, or sparking brushes, while a hum indicates a bearing or a foreign object in the turbine. A clogged membrane reduces airflow, the motor winding doesn't cool and heats up more than usual. Motor bearings lose lubrication over time — a growing hum appears, which at high speeds turns into a howl. Sparking graphite brushes burn the commutator and produce a characteristic burnt smell along with sparking inside the body. A foreign object in the turbine — a small part or a clump of dust — throws off balance and adds vibration to the noise. If you smell burning, it's best to unplug the vacuum cleaner immediately — running with sparking brushes burns the motor commutator, and then a simple brush replacement turns into a motor replacement.
A code on the Vitek display is a hint about which component needs attention. Below are typical signals, their meaning, and steps to take before the technician arrives.
| Code or signal | Meaning | First actions |
|---|---|---|
| Overheating | clogged filter or air duct | turn off, let cool, clean the filter |
| No charge | battery or power supply | check the charging contact |
| Flashing indicator | control board protection | do not disassemble, call a technician |
| Shuts off after seconds | brushes or board | motor diagnostics |
If the Vitek code comes back after a restart and filter cleaning, our free diagnostics includes a technician checking the motor, board, and power supply and identifying the cause before any work begins. Restarting with a clogged air duct just moves air without effect: the flow doesn't pass through the filter, the winding heats up more, and the protection trips earlier each time. During diagnostics, the technician tests the winding, inspects the power contacts and impeller condition, and checks whether the power regulator holds speed under load. Our technicians have 4 to 20 years of experience, and often the cause can be found at this stage without opening the housing. Don't reset the error by turning the unit on repeatedly — restarting with a clogged air duct damages the motor winding, and a unit that could have been cleaned may need replacement.
Blinking indicators and shutdown after a couple of seconds usually point to the control board rather than the motor, because the board cuts power as a protective measure. The power regulator on such a board controls speed via a triac or field-effect transistor, and if the component fails, the motor either won't start at all or runs in jerks. Power is checked first: a voltage drop at the input produces the same symptoms as a burned-out regulator, and an oxidized connector contact adds current spikes. Next, the brushes are inspected — graphite worn down to the base also causes protective shutdown, and they are replaced in pairs to avoid reopening the housing. The board is checked after power and brushes: if you replace the motor first when the problem is the board, you pay twice, so troubleshooting follows a chain from simple to complex.
Cordless upright Vitek vacuums are the most common category in our service. Here's how to tell battery wear from a board failure and what battery replacement achieves.
Fast discharge in a Vitek usually means battery capacity degradation, but if the unit cuts out in jerks mid-clean, the board or contacts are to blame. Lithium cells lose capacity gradually: first runtime drops by a third, then by half. The control board remains functional, but voltage sag triggers protection and shuts off the motor — the owner sees a sudden stop. Oxidized or burned terminals produce a similar symptom: there's energy in the pack, but current reaches the motor inconsistently. 'Training' such a pack doesn't restore it — lithium chemistry doesn't regain capacity, and the sooner you replace the pack, the lower the heat and current load on the board. On high-power turbine models, sag shows up earlier: the motor draws peak current, and protection trips even at moderate wear. So when a customer complains about short runtime, we start Vitek vacuum repair in Almaty with a discharge curve under load, not with random part replacement.
Our technician checks both the battery and the power adapter during diagnostics, because the 'won't charge' symptom in a Vitek can be caused equally by worn cells or a faulty charger. We measure voltage at the terminals with and without load, check charging current and indicator behavior — that shows where the circuit breaks. Diagnostics are free, so we check both components at once rather than replacing parts blindly. If the indicator blinks while the battery pack stays cold, the charger is more likely at fault; if the adapter heats up but capacity doesn't increase, the cells are checked. Swapping one component for another without measurements only confuses the picture: a new adapter won't fix a dead pack, and a fresh pack quickly fails on a faulty charger. The technician compares current and voltage along the entire path from outlet to terminals — that reveals the culprit.
| Work | When it's needed | What we check |
|---|---|---|
| Battery pack replacement | capacity has dropped, discharges quickly | condition of cells and terminals |
| Contact restoration | power is supplied inconsistently | terminal fit and oxidation |
| Board check | cuts out during cleaning | protection and regulator |
We repair Vitek vacuum cleaners in Almaty as a direct service provider: our technician comes to your home or accepts the appliance at our service center.
We repair Vitek both at home and at the service center: our mobile technician arrives within 60 minutes anywhere in the city, while complex cases involving the board or motor are better handled at the service center. At home we fix common issues — a damaged power cord, a clog in the air path, worn brushes, a stuck power button. When board soldering or motor replacement is needed, the appliance is taken to the service center — such work is easier to do in a workshop. The mobile format saves the owner time. If the problem involves power or brushes, the technician on site decides whether it can be fixed right there; when board soldering is needed, the appliance is taken to the service center. The mobile technician checks suction and power and decides what can be done on site.
Before the technician arrives, it's best to unplug your Vitek, not disassemble the housing, and not try to reset the error by turning it on repeatedly. Restarting with a clogged air path or a jammed motor puts extra load on the control board and can turn a minor fault into a component replacement. Unplug the appliance from the outlet, remove the hose and brush so the technician can easily access the machine. Write down the error code if it appeared on the display, and recall the conditions when the failure first occurred — after cleaning a carpet, changing the filter, or a power surge. Describe the symptom and error code to the technician in advance. If the appliance was dropped or ran under overload, mention it: such details narrow down the suspect components even before disassembly.
The decision "repair or replace" depends not on the age of the vacuum cleaner, but on which component failed and the condition of the rest of the machine.
Repair makes sense when the failure is local — brushes, drive belt, filter, hose, or battery — and the motor and housing are in working order. Brushes and the drive belt are consumables that wear out first and can be replaced without disassembling the motor. A clogged filter and a torn hose reduce suction but don't destroy the motor, so replacing them restores the appliance's working power. In cordless models, a worn battery reduces runtime, while the motor and electronics remain functional. In such cases we check the condition of the motor and housing to make sure other components don't need attention. Consider not the cost of the part but the remaining lifespan: if after replacing the component the vacuum cleaner will last several more years, such work is more cost-effective than buying a new one.
Replacement is usually the better choice when the motor has burned out along with the control board, the housing is cracked, or the appliance is many years old and needs several components at once. A burned-out motor often takes the control board with it: you end up replacing two expensive parts, not just one consumable. A cracked housing disrupts how components fit and breaks the seal of the air path, so even a working motor loses suction. On older machines, wear shows up everywhere — battery, brushes, hose, seals — and each part adds to the bill. If a technician finds two or more serious faults, piecemeal repairs drag on, and it's more honest to tell the customer about replacement than to keep fixing things in circles. Look at the total cost of repairs for the whole appliance, not just the one breakdown.
Vitek warranty and repair terms
We provide a 1-year warranty on labor and parts for Vitek repairs. Diagnostics are free, and the technician gives you the price after diagnostics. We run diagnostics before any work, so you see the full picture of faults, not just the one you reported. That lets us agree on the scope of repair upfront and avoid surprise charges for hidden defects. Our technicians have worked with this brand for 7 to 20 years and know which components in specific series tend to fail first. A technician arrives within 60 minutes anywhere in the city, and Tech Service is the direct provider — our own specialist comes to you, not a middleman. The warranty covers both labor and parts, so if the same fault comes back, we fix it at no charge — just keep the work order and receipt.
Breaking down Vitek vacuum cleaner faults comes down to a few practical takeaways — from tracing the cause through the components to deciding whether to repair or replace.
60brands
We repair vacuum cleaners of various brands. Choose a brand to see the page with a description of the work.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your dishwasher won't drain, the most common culprits are a clogged filter or drain hose; less often, it's the pump, impeller…
24 March 2026 · 12 minutes read
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
If your microwave isn't heating but the light and turntable still work, the problem is usually one of the high-voltage components — the magnetron, diode…
15 February 2026 · 12 minutes read
If your refrigerator stops working, first check the outlet, the power cord, and the thermostat setting, and after defrosting let it stand for a while.
4 February 2026 · 12 minutes read
Washing machine error codes are self-diagnostic codes that point to a specific component: drain, water fill, heating, motor, or door lock.
29 January 2026 · 13 minutes read












