Open until 19:00+7 (778) 046 88 53Call a technician
TECH SERVICE technician writing down the error code from a washing machine display

13 minutes read

What Washing Machine Error Codes Mean
and What to Do

Ruslan Ts., washing machine and refrigerator repair technician

Author: Ruslan Ts.,Washing machine and refrigerator repair technician

Published
Updated

Technician’s articleTECH SERVICE02

What an error code means and how to read it

Washing machine error codes are self-diagnostic codes that point to a specific component: drain, water fill, heating, motor, or door lock. The meaning of a code depends on the model, so a technician checks it against the table for your machine. Tech Service deciphers the code, provides free diagnostics, and repairs at your home or in the service center in Almaty with a 1-year warranty on labor and parts.

The combination on the display is the machine's own hint, not a verdict. We explain what it reports, how to read it without a display, and why different brands designate the same fault differently.

What the self-diagnostic code shows

The combination from the control board indicates that one of the components is out of acceptable parameters: drain pump, inlet valve, heating element, motor, or door lock. The electronics compare sensor readings with factory norms and, if there is a deviation, stop the program to prevent flooding the floor or burning the winding. Each combination is tied to a specific component, not a specific part inside it: a warning about a drain problem will appear both for a clogged filter and for worn pump impeller. The same symptom is coded differently by different brands, so first determine the component, and only then look for the cause inside it. Start with deciphering the component — this way you cut out unnecessary checks and avoid disassembling half the machine for nothing. This order saves time and reduces the risk of damaging working parts during disassembly. Write down the code before turning off the power so you don't lose data for diagnostics.

How to read the code without a display by indicator blinking

On models without a display, the value is shown by indicators: the combination of blinking and steady lights corresponds to a specific code from the table for that series. You need to count series, not individual flashes: for example, two flashes, pause, three flashes is 23, not five flashes in a row. The pause between series separates one combination from another; otherwise it's easy to mistake two flashes for one and misinterpret the code, and a wrongly read code will lead to an incorrect conclusion about the fault. Before counting, turn off the spin and wait until the machine finishes the cycle and repeats the indication — usually the combination repeats, and you can verify it twice. Write down the sequence on paper or record a video: from the recording it's easier to match it with the table for your series than to remember how many times the light blinked, so keep the code table for your model at hand.

Why codes differ between brands

Why codes differ between brands. Each brand has its own coding system, so we always check the value against the table for the specific model, not a generic interpretation from the internet. Even within one brand, they differ by generation — for Bosch and Siemens, the older Maxx, Classixx, and Logixx series and the current Serie 2, 4, 6, 8 are read from different tables. They rely on the series and model number from the plate in the door, not just the brand: the same digit on different generations points to different components. In our practice, checking by model number eliminates most diagnostic errors before the visit. When selecting a spare part, the part number or model code is also needed — the technician uses them to find a compatible component rather than guessing. So before contacting a technician, it's worth photographing the plate with the series and model number in advance: this speeds up the check.

Codes by brand and generation

We break down common drain, fill, heating, and motor codes for popular brands and show how the same component is coded differently depending on the brand and generation, so you can find the right combination faster during diagnostics.

Drain codes for Bosch, Siemens, Samsung, Electrolux, and Indesit

One fault across different code systems
BrandDrain codeWhat it means
Bosch, SiemensE18 or F18 (d02 on some models)Drain problem
Samsung5E (SE, E2)Drain problem
ElectroluxE20Drain problem
Indesit, HotpointF05Drain problem

Bosch and Siemens codes by generation

  • F16: door not closed, machine won't start the cycle; check that it fits tightly and there's nothing blocking the lock, otherwise the wash won't start.
  • F17: water not filling within the allotted time; inspect the inlet hose, mesh filter, and water pressure, since a clog or weak flow stops the program.
  • F18: water drain problem; clean the filter and check the drain hose for kinks, otherwise water will stay in the drum.
  • F19: water heating problem; check the heating element and sensor, because without heating the cycle won't complete correctly.
  • F21: motor problem; inspect the brushes and wiring, as the drum won't spin.
  • F23: water in the drip tray, Aquastop protection triggered; fix the leak and dry the tray, otherwise the protection will block startup.

Motor code and when repair is harder than replacement

A motor code (e.g., F21 on older Bosch and Siemens series) points to a motor problem, but we decide whether to repair or replace after diagnostics, not based on the code alone. Brushed motors wear out their brushes over time—they are replaced without touching the winding, so this procedure is usually cheaper and faster. Inverter motors (Bosch EcoSilence Drive, LG Direct Drive) have no brushes, so looking for wear there is pointless: the technician checks the control board, windings, and Hall sensor, and it's often the electronics that cause the failure. Our technicians work with both designs and have 4 to 20 years of experience; during free diagnostics they determine exactly what has failed. Before replacing a unit, ask whether the drum is serviceable—on a sealed drum the bearing isn't replaced separately, and that changes the whole repair estimate.

The symptom points to the cause, even if the code is unclear

Owners often don't remember the code on the display but clearly see what the machine is doing wrong. We go through common scenarios and list two or three causes each—from the simplest and cheapest to the complex.

Machine won't drain water

  • Drain filter: at the bottom front, behind the service cover, is most often clogged with debris—lint, coins, small items; before cleaning, place a low container and a cloth underneath.
  • Drain hose: check for kinks and clogs, especially if the machine is right against a wall or furniture; when inspecting, remove the corrugated hose from the pipe and rinse it.
  • Drain pump: check whether the impeller spins freely; a multimeter won't show a jammed pump, it needs a visual inspection, and a foreign object is removed through the chamber.
  • Main cause of pump failures: debris and a clogged filter, not scale, so cleaning often solves the problem without replacing the part.

Machine won't fill with water or won't spin

Machine won't fill with water or won't spin. If water isn't filling, check the inlet tap, the inlet filter mesh, and the inlet valve; if it won't spin, check for load imbalance, drainage, the belt, or the motor. The inlet tap might simply have been left closed after pipe repairs, and the mesh gets clogged with rust and sand from the water supply—rinse it under pressure and put it back before turning the water on. Spin often doesn't start because the machine hasn't drained the water, so fix the drain problem first, then check imbalance and the drive. The belt stretches and slips over time, and brush wear only happens on brushed motors—inverter motors like Bosch EcoSilence Drive and LG Direct Drive have no brushes. During water fill, the drain pump doesn't run, so if you hear the pump humming at that moment, check the board rather than looking for a clog.

Leaks from the bottom, doesn't heat, or stops mid-cycle

  • Leaking from the bottom: hoses, pump, connections; a torn door seal leaks at the front, right at the door, leaving a puddle at the loading threshold.
  • Not heating: heating element or temperature sensor; on Bosch and Siemens the heater is removed through the front panel, so testing starts with checking the heating element and sensor for continuity.
  • Stops mid-cycle: most often drainage, imbalance, or the motor; the control board is one possible cause but not the main one—it's checked last.
  • Check order: first drainage and imbalance, then the drive, and only finally the electronics; this rules out simple faults without unnecessary disassembly.

What you can check yourself and how to do it safely

Some checks take just a few minutes and you can do them yourself, but there's a line where you need a technician. Here are safe steps, the order to do them in, and what not to do.

Safe water drainage before checking

Before any check, unplug the machine, drain the water through the emergency drain hose behind the service flap at the bottom front, placing a towel underneath. Pull the hose out of its clip, point it into a low container, and open the plug—water flows by gravity. Only unscrew the drain filter once the tub is empty. If there's no emergency hose, tilt the machine carefully over a basin to drain the water, but with a full tub the center of gravity shifts and it's easy to tip the machine over. The water in the tub can be hot after a high-temperature wash, so drain it into the container carefully, and never unscrew the filter while water is still inside. Keep a second towel and a wider basin nearby—some water will still spill when you remove the cover. This safe drainage before checking helps you find washing machine errors faster without disassembling the pump or risking a flooded floor.

What to check yourself and when to call a technician

  • You can do it yourself: clean the drain filter of coins and lint, check that the tap is open, rinse the mesh filter in the inlet hose, untangle bunched-up laundry—these are common causes of stopping.
  • Don't do it yourself: disassemble the pump, unscrew the filter with water still inside, touch the control board, or remove the heating element without experience—you risk flooding the floor and damaging the electronics.
  • Time to call a technician: the code returns after a reset, the machine won't drain even with a clean filter, there's a burning smell or a leak from the bottom.
  • Diagnostics: we offer free diagnostics, a technician arrives at your home within 60 minutes anywhere in the city, and identifies the cause before any repair.

Why resetting the error doesn't always help

Resetting the code only clears the message from the display but doesn't fix the faulty component, so when the signal repeats we look for the cause instead of just clearing the memory. A button combination erases the control board data, and the machine starts the cycle fresh. If a component is truly faulty, the board will detect the deviation again—via pump current, level sensor readings, or temperature—and bring back the same code. A random glitch from a power surge doesn't behave this way: the cycle completes fully and the signal doesn't reappear. Washing machine faults that repeat on the second and third wash point to a specific component, not the board. We decode the code by model and check it against the table for your series before disassembling the machine. Repeated runs with a faulty drain or heating add wear, so if the code returns, it's best to stop washing and not run the drum idle until diagnostics.

All indicators flashing and other unusual signals

Not every machine signal reads as a code on the display. Here's what it means when all lights flash, why a heating error is dangerous, and why water in the sump requires inspection: it points to electronics faults, overheating, and leaks—don't delay diagnostics.

All indicators flashing—is it a code or a board failure

All indicators flashing usually means the machine is displaying a code through a combination of lights, not that the control board has failed. On models without a display, the code is shown by indicators: some stay on steady, others flash, and the sequence is read from the table for that specific series. On Indesit and Hotpoint, this kind of indication appears on budget models where a display isn't part of the design. The control board can indeed be the cause, but it's not the main one, so first decode the combination using the model's table, and check the board later. The meaning of the code depends on the model, and the technician matches it against the table for your machine. Practical tip: before calling a specialist, take a photo of which lights are on and which are flashing — the picture makes it easier to identify the series and narrow down the causes. Such a photo saves diagnostic time and helps the technician prepare the right parts in advance, while saving you from unnecessary disassembly costs.

Is it safe to continue washing with a heating error

With a heating error, it's better not to continue the wash: without heat, detergent doesn't dissolve fully, and a faulty heating element or temperature sensor can behave unpredictably. Code F19 on older Bosch and Siemens series indicates a heating problem: the water stays cold, the cycle drags on, and clothes come out poorly washed. Restarting with this signal doesn't fix the cause and only adds stress to the component, so stop the cycle and check the heating element and sensor. On most brands, the heating element can be replaced without removing the drum, so there's no point in delaying the inspection. A non-obvious consequence: if you only wash in cold water, the fault may not appear for weeks, while scale builds up on the heating element — when you switch to a program with heating, the component fails abruptly. Practical tip: don't put off these washes and don't expect the error to disappear on its own — timely diagnostics costs less than replacing the component.

Water in the sump and Aquastop protection

A code indicating water in the sump (for example, F23 on older Bosch and Siemens series) means the Aquastop protection has tripped and the machine needs inspection. The sensor detects moisture in the lower part of the housing and blocks water intake so a leak doesn't flood the floor. Water in the sump is a consequence of a leak inside the housing, so you look for the source — hoses, pump, or connections — rather than just removing the water. If you simply scoop out the water and start the wash again, the protection will trip again on the next intake, and water will end up in the sump once more. Expert recommendation: after Aquastop trips, wipe the sump dry and inspect the connections before turning the machine back on — this way you'll see the fresh leak trace before it washes away and identify the faulty component faster. On machines without a display, water in the sump is signaled by a combination of indicators, which the table for your series explains.

When to call a technician and how we work in Almaty

We explain when a technician visit is needed and how our work is organized — from request to warranty. Below are the signs that self-checks no longer help: faults repeat, equipment runs unstably, and diagnostics without tools waste time.

When you need a technician

  • Repeating signal: if the fault returns after one or two cycles, resetting only hides the component failure rather than fixing it.
  • Water remains after cleaning the filter: the clog is cleared but draining doesn't happen — the cause is in the hose or pump, and a technician needs to check it.
  • Signal for motor, heating, or water in the sump: a motor or heating element fault, or Aquastop tripping, requires disassembly and on-site measurement of components.
  • Stopping mid-cycle repeats: if the machine stops on the same program, it's usually about draining, imbalance, or the motor.
  • Burning smell or a puddle on the floor: such signals shouldn't wait for the next wash — call a specialist immediately to avoid making the fault worse.

How the visit and diagnostics work

We come to your home or repair in our service center. Diagnostics are free, and the technician gives you the price after diagnostics. On-site, the specialist checks the signal against the table for your model — for Bosch and Siemens, that's the Serie 2/4/6/8 generation or older Maxx, Logixx, Classixx, where the value is read from the indicators. The part is selected by part number or model code: for Bosch, the E-Nr is on the plate inside the door. So repair doesn't turn into guesswork, and replacing the heating element on most brands is done without removing the tank. Our technician comes himself, no middlemen — you work directly with the person who will do the repair. A call-out anywhere in the city takes up to 60 minutes.

Warranty and payment

We give a 1-year warranty on labor and parts, accept payment via Kaspi QR, Kaspi Red, card, cash, or bank transfer for companies, and quote the price after free diagnostics. It covers both the work performed and the installed part, so if the same unit fails again, the visit doesn't start with a new diagnostic. Our experience ranges from 4 to 20 years across our technicians, and it shows in complex cases: replacing the bearing requires removing the tank and drum, and on a sealed tank the bearing isn't replaced separately. If the signal returns after repair, the technician investigates the cause again rather than blaming wear and tear, because the warranty covers both the work and the installed part, so a repeat visit for the same unit doesn't become a new troubleshooting saga for the owner. A practical tip: keep your repair documents — they make warranty claims easier and confirm that the unit was serviced by us.

Decoding washing machine error codes

Self-diagnostic codes help narrow down the fault but don't replace checking the components: they only point you in the right direction. Below is a short summary to start with when the machine stops with an error signal, plus a practical tip to record your check results.

  • The code points to a unit, not a verdict: draining, water fill, heating, motor, or door — it's a search area, not a ready diagnosis, so don't rush to replace parts at random.
  • The code value depends on the model: the same symbol means different things across series, so the table must be matched to the generation and series, or you can easily mistake the unit.
  • Without a display, the code is read from the indicator combination: the number of flashes and pauses add up to the fault number, which is then checked against the table.
  • It's safe to check the filter, tap, mesh, and imbalance yourself: these causes are fixed without disassembling the body — just inspect and clean the accessible parts.
  • If the signal returns after a reset, you need a technician: a repeat indicates a faulty unit, not a random glitch.

Our technicians in Almaty

01 / 08
Ruslan Ts., washing machine and refrigerator repair technicianexperience9 years

Ruslan Ts.

Washing machine and refrigerator repair technician

Damir M., general household appliance repair technicianexperience12 years

Damir M.

General household appliance repair technician

Dilmurat S., field technician for washing machine and refrigerator repairexperience10 years

Dilmurat S.

Field technician for washing machine and refrigerator repair

Dima, expert washing machine repair technicianexperience8 years

Dima

Expert washing machine repair technician

Nikita M., field refrigerator repair technicianexperience8 years

Nikita M.

Field refrigerator repair technician

Oraz, senior washing machine repair technicianexperience8 years

Oraz

Senior washing machine repair technician

Radik T., dishwasher repair technicianexperience11 years

Radik T.

Dishwasher repair technician

Rustem T., washing machine repair technicianexperience9 years

Rustem T.

Washing machine repair technician