experience9 yearsRuslan Ts.
Washing machine and refrigerator repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 746 00 26Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Diagnostics are free.
Our own technicians4 to 20 years of experience




Repair prices
The symptom points to a component: from the filter and pump to the heating element and bearing.
clogged filter, hose, or pump
from3 000 ₸
closed tap, clogged mesh filter, or valve
from3 000 ₸
imbalance, water in the drum, belt, or motor
from3 000 ₸
hoses, pump, or connections
from4 500 ₸
heating element or temperature sensor
from3 500 ₸
imbalance, shock absorbers, or bearing
from5 000 ₸
the code points to a component: drain, fill, or heating
from4 500 ₸
in commutator motors, causing sparking and jerking
from3 000 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1 visittime
from 4 500 ₸cost

BeforeAfter5 steps

Five steps from your request to checking the machine's operation.
Describe the symptom and your Whirlpool model so the technician brings the right tools.
A technician arrives within 60 minutes anywhere in the city.
Diagnostics are free when you order a repair, and the technician identifies the cause.
The technician quotes the cost of labor and parts, and you confirm the repair.
The machine is tested in all modes, and you accept the result.
The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsExpert washing machine repair technician
experience8 yearsSenior washing machine repair technician
experience9 yearsWashing machine repair technician
We reply during working hours
Describe the fault over the phone: the technician will tell you what to check before the visit and which tools and parts are needed for the repair.

Warranty question? Call us
+7 (778) 746 00 267 898 reviews of repairs at TECH SERVICE in total
Ринат Х.Order No. 920200 · 7 October 2026
oursИскал мастерскую поближе к дому, чтобы не мотаться с техникой через полгорода. Жена сказала выкинуть, я решил сначала показать мастеру. Проблема — не включается. Дима возился с этим дольше, чем планировал, но довёл до конца. Диагностику сделали бесплатно, хотя я был готов платить. Разобрали, посмотрели: модуль управления. Сравнивал с двумя другими — здесь вышло ровнее всех. Хороший сервис, побольше бы таких. Сказать, что доволен — ничего не сказать)
Сабина Г.Order No. 564334 · 23 September 2026
oursХотел сначала вызвать мастера на дом, потом передумал. Жалоба простая: течёт. Вернули в тот же день, всё функционирует
Айгуль К.Order No. ZK-2025/223 · 11 September 2025
oursБыло важно, чтобы сделали до выходных — гости, то-сё. Уже не верил, что это можно починить. Повод для визита: не сушит. Дима помог выбрать, без навязывания. Могли бы взять больше, но взяли по-божески. Заодно поменяли: тэн. Tech-service посоветовали в чате дома, спасибо им. Второй месяц — полёт нормальный!!
Аружан К.Order No. 2025-2417 · 24 January 2025
oursДолго откладывал ремонт, потом всё-таки собрался. Жалоба простая: не сушит. Второй месяц — полёт нормальный.
Ержан А.Order No. TS-1927 · 3 May 2024
oursС чем пришёл: течёт. Ораз принял, посмотрел и сразу сказал, что делать. Проверили на всех режимах, всё чётко!!
Наталья С.Order No. 929586 · 27 December 2023
oursПовод для визита: ошибка на дисплее. Рустем Т снял деталь, показал износ, вопросов не осталось. Нагрев в норме, постороних звуков нет.
Гаухар Н.Order No. 788281 · 9 October 2021
oursПрочитал кучу отзывов, половина — реклама, но тут вроде живые. Оставил заявку на ремонт промышленной стиральной машины. Повод для визита: вибрация. Починили и дали гарантию на месяц.
Мирас С.Order No. TS-6433 · 12 March 2021
oursАлдымен интернеттен іздедім, кейін таныстарым осы жерді ұсынды. Бағасын алдын ала келістік, соңында өзгерген жоқ. Келесіде де осында келемін.
Анна Т.Order No. 405199 · 12 November 2019
oursПервое, что заметил: не отжимает. Отдельно спасибо мастеру — Рустем Т, терпения ему хватило. Нагрев в норме, посторонних звуков нет
Алмас Д.Order No. ZK-2018/189 · 30 September 2018
oursСимптом был очевидный: не сушит. Рустем Т перезвонил, когда всё было готово. Гудит ровно, не греется, всё как надо.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionWhirlpool factories are located in several countries, and the specific assembly depends on the model and batch — it's indicated on the machine's rating plate. For repair, it doesn't matter: the technician selects parts by model number, not by country of assembly.
First check the drain filter at the bottom front behind the service flap — lint and small items are most commonly found there. If the filter is clean and the pump impeller doesn't spin freely, it's likely the pump.
If the tub is full, the machine won't proceed to spin: the water must drain first. By frequency, the causes are a clogged filter or hose, then the pump, less often an unbalanced load or the belt. It depends on the model.
If there's a puddle under the machine, the culprits are more often the hoses, drain hose, or pump; the door seal leaks at the front near the door. The technician finds the leak point after removing the side or front panel.
Usually the heating element is at fault, less often the temperature sensor or its wiring. The technician tests the heating element and checks the sensor readings, then replaces the faulty part.
Yes, most Whirlpool washing machine breakdowns are fixed by the technician at your home: the filter, pump, heating element, hoses, and pipes are replaced on site. The machine is taken to the service center only if the tub needs to be disassembled or the control board requires complex repair.
Tech Service repairs Whirlpool washing machines in Almaty at your home or in our service center. A technician arrives within 60 minutes anywhere in the city, diagnostics are free, and we provide a 1-year warranty on labor and parts. We first check the error code against the table for your model, then agree on the repair.
Whirlpool machines have three most common issues: not draining, not spinning, and not filling with water. For each, we go through the causes from simple to complex so you understand what the technician checks and in what order.
Most often, water won't drain because the drain filter at the bottom front behind the service flap is clogged; less often, it's a kinked hose, and only then do we suspect the drain pump. The filter gets clogged with lint, threads, and small items from pockets, and the drain hose is checked for kinks along its entire length to the sewer. The drain pump is inspected last: its impeller should spin freely without jamming. A multimeter won't show a jammed pump — the technician checks whether the impeller spins freely, and the cause of pump failures is usually debris (coins, lint, small items) and a clogged filter. In our practice, most Whirlpool washing machine repairs in Almaty involve a clogged filter — it's the simplest and fastest cause of all three.
If the drum won't spin and water remains in the tub, the cause is almost always one of four: load imbalance, a non-working drain, a stretched drive belt, or motor wear. Imbalance is the simplest: one heavy item clumps together, and the machine can't spin the drum at the usual 800–1600 rpm depending on the model. A non-working drain is checked as in the scenario above — filter, hose, pump. The drive belt stretches over time and slips, and the motor is inspected afterward. First, imbalance and drainage are ruled out — these can be checked without disassembly; the belt and motor are looked at later because they require access, and inverter motors have no brushes, so brush wear doesn't apply to them. Brushes wear only on brushed motors, so with an inverter drive the technician doesn't look for the cause there.
Water not filling is most often due to a closed tap, a clogged inlet hose mesh, or a fill valve; if the machine stops mid-cycle, the culprit is usually drainage, imbalance, or the motor, and the control board is just one possible cause, not the main one. The inlet hose mesh is rinsed of rust and sand, the tap is checked to be fully open, and the valve is inspected if the first two causes are ruled out. The drain pump doesn't work during filling — if you hear humming and no water fills, it's not the pump. The technician follows the chain from the tap and mesh to the valve, and checks the board last. In such cases, Whirlpool washing machine repair starts with free diagnostics: on site, it's clear where the chain breaks, and then the technician doesn't guess but checks the specific component.
The code on the display is a hint, not a verdict. We show what common Whirlpool codes mean and why a specialist still cross-checks the interpretation with the table for the specific model.
The technician starts by identifying the error code and symptom, checks it against the table for the model, and only begins disassembly after narrowing down the suspect components. The code itself points to a component, not a specific part: for F18, a Tech Service technician first checks the drain filter and hose, then checks whether the pump impeller spins freely, and only then removes the drain pump. This way, disassembly doesn't turn into a random teardown. In our experience, most drain-related calls are resolved in the first two steps—without removing any components. Moreover, on models without a display, the technician relies on the combination of indicators and on the stage of the cycle where the machine stopped—this narrows the search faster than any code. Whirlpool washing machine repair in Almaty based on an error code begins with exactly this kind of check, not with disassembly.
A leak from underneath and no heating are two breakdowns the owner notices right away. We break down the causes by component and summarize common symptoms in a table.
Leaks from underneath are most often caused by hoses, the pump, and tubing, and if water collects at the front near the door, the door seal is to blame. The rubber door gasket loses its elasticity over time, cracks, or gets clogged with lint, and then moisture seeps out along the front panel. Connecting hoses suffer from scale, kinks, and loose clamps, while the drain assembly suffers from debris: coins, lint, small items that clog the filter and impeller. The location of the leak points to the component: at the front near the door, check the seal; at the bottom, check the hoses and pump. Our technicians don't replace everything in sight—they find the source by the water trail so they don't touch working parts, which makes the repair more precise and cheaper for the owner. So before calling, wipe the floor dry and turn the machine on again: a fresh water trail will show exactly where it's dripping from, and the technician will bring the right part right away.
If the water isn't heating, the cause is usually the heating element or the temperature sensor, and the technician checks both before replacing anything. The coil gets covered in scale, burns out, or breaks, and the sensor can give incorrect readings and throw off the wash program. Washing in cold water is noticeable right away: the detergent doesn't dissolve, clothes come out with streaks, and a code appears on the display whose meaning depends on the model—the technician checks it against the table for your machine. On most brands, the heater can be removed without dismantling the tub; it's one of the fastest jobs, so don't put off the repair for fear that the whole machine will have to be taken apart and a part will take weeks to arrive.
| Symptom | Common cause | Second cause | What we check |
|---|---|---|---|
| Not draining | Drain filter | Drain pump | Impeller |
| Not filling | Tap and mesh filter | Inlet valve | Water supply |
| Not spinning | Imbalance | Drain, belt, motor | Drain and belt |
| Leaking from underneath | Hoses and tubing | Drain pump | Water trail |
| Not heating | Heating element | Temperature sensor | Both components |
We handle Whirlpool washing machine repair in Almaty on-site or at our service center: here's how a visit works, what the technician does during diagnostics, and how a component replacement goes.
A Tech Service technician arrives at your home within 60 minutes anywhere in the city, and diagnostics are free — the specialist gives you the price after the check. We cover all neighborhoods: from the center to the outskirts, where dense buildings and narrow stairwells make it hard to move appliances. On site, the technician inspects the machine, listens to the drum, checks draining and water intake, and compares readings with the table for your model. If the problem can be fixed on the spot, we do it right there in front of you — no need to transport the machine or wait in a service queue. If it can't be done at home, we repair the machine at our service center; the visit and diagnostics are needed so you don't haul the appliance blindly and don't pay for transportation when the issue can be solved on site.
On site, the specialist matches the error code with the table for your model, checks the unit based on the symptom, and selects the part by part number or model code. First, they rule out the simple things: a clogged filter at the bottom front behind the service flap, a pinched inlet mesh, a blocked hose. Then they move to the components — pump, inlet valve, heating element, motor. The code on the display of a Whirlpool often points to a group of causes rather than a single part, so the technician confirms the version by inspection and testing. For example, E18 or F18 on some d02 models indicates a drain problem, but doesn't distinguish a clogged filter from a worn pump — only disassembling the unit shows that. Selecting by part number or model code matters because visually similar components from different Whirlpool generations are not interchangeable; this way the part fits the first time, and no repeat visit is needed.
On most brands, the heating element is replaced without removing the tank, while bearing replacement is the longest job because the tank and drum have to be taken out. The heating element is accessible after removing the wall panel, so it's replaced faster than other components and without fully disassembling the body. With the bearing it's different: the machine is disassembled, the tank is removed, its halves are separated, the old bearing is pressed out and the new one pressed in, then everything is reassembled and tested at idle and during spin. The bearing is replaced only if the tank is split-type; on a sealed tank it's not replaced separately — and that determines whether it's worth taking on such a machine at all. In my opinion, this is exactly what the owner should find out first: it decides whether the repair goes ahead or whether replacing the machine makes more sense.
While you wait for the technician, the main thing is not to damage the machine or the floor. Below is a safe first step when there's water in the tank and an honest framework for when restoring a Whirlpool washing machine is justified and when you're better off looking at a new one.
Repair is justified when a single component is replaced — heating element, pump, belt, door seal; but if the bearing is worn on a sealed tank, it's not replaced separately, and that's the main argument for a new machine. On a split tank, the bearing can be replaced, but it's the longest job: the tank and drum are removed completely, so this operation is planned separately from minor repairs. On most brands, the heating element is removed without dismantling the tank, and the belt is changed quickly — these are the most common fixes in the city. The decision depends not on the age of the machine but on whether the tank is split-type and whether the component can be replaced separately; the technician tells you this directly after diagnostics so you don't pay for work that won't solve the problem.
Before you book, it helps to know what you get when the work is done. Here's a quick look at the warranty, diagnostics, and payment — no prices here; the technician gives you the total after inspecting the machine.
We give a 1-year warranty on labor and parts — this covers both home visits and in-shop service. The term is the same for both formats, so you don't have to choose between convenience and protection: the technician comes to you or you bring the machine to us, and the terms stay the same. The warranty covers the replaced component — heating element, pump, belt, or bearing — and the installation itself. The part and the labor are covered together, so if you come back you don't have to prove the part was installed by us: our records show which part was replaced. In our experience, this removes the main point of dispute — whose part failed and who is responsible for the replacement. The technician records the replaced component on site before leaving.
Diagnostics are free, and the technician gives you the cost of work after they're done; you can pay with Kaspi QR, Kaspi Red, card, cash, or bank transfer. This approach is convenient because you decide whether to go ahead based on the actual fault, not over the phone: the technician opens the machine, checks the component, and only then tells you the scope of work and the final amount. You pay for the agreed work and parts — nothing extra is added to the bill. You can pay in any convenient way, including card and cash. If after the inspection you decide not to repair the machine, you don't pay for diagnostics — this makes sense for both you and the technician, who doesn't waste time arguing about the bill. This approach lets you calmly compare options and make a balanced decision without pressure.
Here are the key points that shape diagnostics and repair decisions for a Whirlpool washing machine — from the first component in the drain path to choosing between replacing a part and buying a new machine.
85brands
We work with washing machines of every brand sold in Kazakhstan — from Samsung, LG and Indesit to Beko, Haier, Artel and rare imported makes. Can’t find yours in the list? Call anyway — a technician will come and take a look.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
Washing machine error codes are self-diagnostic codes that point to a specific component: drain, water fill, heating, motor, or door lock.
29 January 2026 · 13 minutes read
If your washing machine won't spin, it's usually an unbalanced load, a clogged drain filter or hose, and less often the pump, belt…
19 January 2026 · 12 minutes read
If your washing machine isn't heating water, the heating element or temperature sensor is usually to blame, less often the control board or wiring.
25 December 2025 · 12 minutes read
If your washing machine won't turn on, first check the outlet, extension cord, and the circuit breaker in your panel, then the plug and power cord.
24 November 2025 · 13 minutes read












