experience9 yearsRuslan Ts.
Washing machine and refrigerator repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 746 00 26Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Free diagnostics.
Our own technicians4 to 20 years of experience




Repair prices
Common symptoms and likely causes the technician checks during diagnostics. The exact cause and repair cost are confirmed after inspection.
clogged filter, hose, or pump
from3 000 ₸
closed valve, clogged mesh filter, or inlet valve
from3 000 ₸
imbalance, water left in the drum, belt, or motor
from3 000 ₸
water not drained, imbalance, or belt
from3 000 ₸
hoses, pump, or connections
from4 500 ₸
heating element or temperature sensor
from3 500 ₸
imbalance, shock absorbers, or bearing
from5 000 ₸
the code points to a specific component
from3 000 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1 visittime
from 3 000 ₸cost

BeforeAfter5 steps

Five steps from your request to checking the machine after repair.
Describe the symptom; the technician will clarify details and schedule a visit.
The technician brings tools and common Beko parts; the exact set depends on the symptom.
The technician agrees with you on the scope of work and the list of parts to replace.
After the cost is approved, the technician performs the repair and replaces parts.
The technician confirms the scope and cost of repair before starting work; ask for details.
The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsExpert washing machine repair technician
experience8 yearsSenior washing machine repair technician
experience9 yearsWashing machine repair technician
We reply during working hours
Leave a request or ask the technician about the symptom — they'll tell you what to check before the visit and agree on a convenient time. 1-year warranty on labor and parts.

Warranty question? Call us
+7 (778) 746 00 267 898 reviews of repairs at TECH SERVICE in total
Сабина Г.Order No. ZK-2025/724 · 12 December 2025
oursДима не стал навязывать дорогую запчасть, поставил нормальную. Tech-service посоветовали в чате дома, спасибо им. Нагрев в норме, посторонних звуков нет.
Данияр С.Order No. 2025-3853 · 7 August 2025
oursПробовал найти мастера в своём районе, но все были заняты. Симптом был очевидный: не отжимает. Включил, проверил, работает
Акбота Т.Order No. TS-2305-226 · 6 November 2023
oursЦена имела значение, но и гарантия тоже. Симптом был очевидный: ошибка на дисплее. Внешне как новый, если не считать мелкой царапины!!
Индира П.Order No. 2023-3911 · 14 June 2023
oursС чем пришёл: течёт. Дильмурат С взялся за то, от чего другие отказались. Работает как раньше, придирок нет.
Сергей Р.Order No. TS-2210-605 · 29 November 2022
oursДруг посоветовал, у него похожая история была. Повод для визита: вибрация. Крутит ровно, без рывков
Наталья С.Order No. 107334 · 4 July 2021
oursПозвонил в три места, здесь единственые назвали цену сразу. Работает как раньше, придирок нет.
Малик Т.Order No. ZK-2017/348 · 18 September 2017
oursКүтуге уақытым жоқ еді, сол күні алып кеттім. Тексеру кезінде бәрін өзі көрсетті. Бағасын алдын ала келістік, соңында өзгерген жоқ. Қосымша бөлшек қажет болды, бірақ бағаны көтермеді. Кепілдік берді, бұл мен үшін маңызды. Бір күнде жөндеп берді, кешіктірмеді. Кәсіби мамандар, рақмет.
Елдос К.Order No. ZK-9793 · 17 June 2017
oursХотел сначала вызвать мастера на дом, потом передумал. Ремонт промышленной стиральной машины — вот с этим и пришёл. Основная жалоба — не греет воду. В списке работ — тэн. Сказали 17 500, а потом ещё и скидку сделали. Второй месяц — полёт нормальный
Богдан С.Order No. 95121 · 11 December 2016
oursПробовал найти мастера в своём районе, но все были заняты. До последнего откладывал, но пришлось признать: не сушит. Поставили новую деталь: насос. Мастер сразу сказал, что к чему, без размытых формулировок. Проверили при мне, показали, что всё держит.
Ксения И.Order No. 80442 · 12 March 2016
oursБыло подозрение, что дело в плате, хотелось услышать второе мнение. Первое, что заметил: не включаеться. Включил, проверил, работает.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionUnplug the machine for a couple of minutes or hold the Start/Pause button for a few seconds — the current program will reset. If the fault comes back, the control board may be the issue, and a technician's diagnostics will be needed.
Turn the power off and back on, then select the program again — that's often enough. If the error repeats at the same stage, a technician will check the sensors and control module during free diagnostics.
It depends on the model and load: with careful use and filter maintenance, the machine lasts noticeably longer. The manufacturer states the exact service life in the instructions for each specific model.
Most often it's an unbalanced load, uneven installation, or worn bearing, and less often a loose belt. A technician will check the drum and supports on site and tell you what needs replacing and what just needs adjusting.
First, they ask about the symptoms and display codes, then check the components in sequence: drainage, water intake, heating, motor. Diagnostics are free, and afterward the technician explains the cause and gets your approval for the work.
Yes, there is a 1-year warranty on labor and parts. The technician records the terms after the repair so you can reach out if the issue happens again.
Tech Service repairs Beko washing machines in Almaty with its own technicians: arrival within 60 minutes anywhere in the city, free diagnostics, and a 1-year warranty on labor and parts. The technician comes to your home or accepts the machine at the service center, and quotes the price after diagnostics.
"Won't drain" is the most common reason to call a technician for a Beko. Let's look at what code E18 means, the three parts checked first, and what you can do before the technician arrives.
Code E18 or F18 (d02 on some models) means a drain problem: the machine couldn't pump out the water within the allotted time. We check the code against the table for your specific Beko model, because on different generations the same error can point to different parts. The code relates to the drain circuit: the filter, hose, and pump are connected to it. The symptom is always the same — water stays in the drum, the spin cycle doesn't start, and the program stops. On models without a display, the code is shown by indicator lights: their blinking pattern is read from the table in the manual. That's why a "blind" Beko is diagnosed not by a single symptom but by a combination of signals and how the pump behaves — whether it hums, clicks, or stays silent.
When it "won't drain," we go from simple to complex: first the filter at the bottom front behind the service flap, then the hose for kinks and clogs, and only then the pump. In most cases, a clogged filter or debris in the pump impeller is to blame. A multimeter won't show a jammed pump — the technician checks whether the impeller spins freely. The cause of pump failures is coins, lint, and small objects, not scale, so prevention means cleaning the filter, not using "anti-scale" products. The pump doesn't run during water intake, so humming during the wash cycle has nothing to do with it. Technicians start Beko washing machine diagnostics in exactly this order — from the filter to the pump.
If your Beko won't fill with water, the machine stops at the start of the cycle and shows a code. Let's look at what E17 means and the three causes checked first — from the tap to the inlet valve.
Code E17 or F17 means water didn't fill within the allotted time. We check it against the table for your specific Beko model: on some generations it points to the inlet valve, on others to low water pressure or a clogged mesh filter. The meaning depends on the model, so the technician doesn't guess but looks up the interpretation for your machine. In practice, E17 and E18 are two sides of the same cycle: the first means water didn't come in, the second means it didn't go out. When the machine shows one, then the other, look for a common source rather than two separate parts — a kinked inlet hose or a clog in the drain system. On some models without a display, the error isn't shown on screen — the indicators signal the fault, and their combination is also checked against the manufacturer's table. Beko washing machine repair with this error starts with checking the water supply. Before calling a technician, open the tap fully and check that the hose behind the machine isn't kinked.
When it "won't fill," we check in order: is the inlet tap open, is the mesh filter in the inlet hose clogged, is the part that supplies water to the drum working. Most often the tap or mesh filter is to blame, and the valve is replaced less often. The mesh filter gets clogged with rust and sand from the water supply — it's rinsed and put back without replacing the part. The inlet valve is checked for water flow with the tap open: if there's pressure but no water goes into the drum, the valve itself is the cause. The drain pump doesn't run during filling — if you hear humming and water "disappears" right away, the problem isn't filling but that the machine is draining at the same time; this changes the direction of diagnostics. Our technicians start with free diagnostics and quote the cost of work after it, and provide a 1-year warranty on labor and parts.
No spin, no heat, and stopping mid-cycle are three symptoms that owners often blame on a "control board failure." Let's break down the real causes by component and give you honest caveats about motor and bearing repair.
| Symptom | Common causes | What we check |
|---|---|---|
| Won't spin | imbalance, drain, belt, motor | laundry, drain, belt, brushes |
| Won't heat water | heating element, temperature sensor | heating element, NTC |
| Stops mid-cycle | drain, imbalance, motor | filter, laundry, brushes |
| Noisy during spin | bearing, imbalance | drum, shock absorbers |
| Won't reach spin speed | motor, belt, board | belt, brushes, module |
On most brands, the heating element is replaced without removing the tub — access is through the front panel. That's why "won't heat water" is usually fixed faster than noise during spin: you don't have to remove the tub and drum like you do for a bearing replacement. Our technicians first check heating on a test cycle, then test the heater and temperature sensor with a multimeter. If the water isn't heating, they check not only the heating element but also the sensor: a working heater with a faulty NTC gives the same symptom, and replacing just the heating element won't solve the problem. Heating is the most common reason for complaints about "washing in cold water," and in most cases the part is replaced in a single visit. In our experience, the temperature sensor fails less often than the heater, but it's the one that skews readings and lengthens the cycle. If you need Beko washing machine repair at home, the technician comes to your address and checks the heating on site.
A puddle at the base of the washing machine can be confusing: water flows down, but the source may be somewhere else entirely. Let's look at where to look for water and how a specialist finds the cause without taking the whole machine apart.
If water collects at the bottom, the usual suspects are the hoses, drain pump, or the inlet and drain hoses; the door seal leaks at the front by the door, not at the base of the machine. The leak location points directly to the part: if it's dry around the loading door but there's a puddle near the tub, check the hose connections and pump housing. The drain filter is located at the bottom front behind the service flap, and its O-ring can also start leaking water onto the floor over time. A leak often doesn't show up constantly but only during spin or fill — then the connection leaks under pressure but stays dry at rest. That's why we always ask the owner when during the cycle the water appears, and only then remove panels: this immediately narrows down the suspect parts. If you need Beko washing machine repair, the technician comes to your home and finds the source of the leak on site.
During the free diagnostics, we match the error code against the table for your specific model, check the components based on the symptom, and confirm the cause before replacing any part. We select the part by part number or Beko model code, so a new pump or hose fits without modifications. Diagnostics without disassembling the entire body saves time and parts: we go from the code and symptom to the specific component instead of replacing the pump, valve, and heating element one by one hoping to guess. This order matters for the owner too—they pay for one confirmed fault, not for swapping out working parts. A Tech Service technician records the cause before work begins, so the replacement isn't a gamble, and the result is checked right after reassembly.
Work is done at the customer's location or in the service center—the choice depends on the breakdown. Let's go over how to call a technician, how long to wait, and how a direct provider differs from an aggregator.
Customers call a technician to their home, and we arrive within 60 minutes anywhere in the city. Tech Service is a direct provider: our own technician comes to you, not an intermediary who passes the request to a third party. Requests are taken by phone, and the staff member clarifies the error code and model to bring the right parts. When it comes to washing machine repair in Almaty, owners most often order it with a home visit—that way you don't have to transport the appliance across town. On site, the technician performs free diagnostics, states the cause, and agrees on the scope of work. A direct provider is responsible for the result end-to-end—from diagnostics to warranty—whereas with an aggregator, quality is the responsibility of someone else you didn't choose.
Some breakdowns are fixed at the customer's location, while others are better handled in the service center—for example, when long work with the tank and drum is needed. We perform work both on-site and in the workshop. Replacing a heating element or pump usually happens on site: these are quick operations, and there's enough space in the bathroom or kitchen. However, servicing Beko washing machines at home isn't always possible when the tank and drum need to be removed—such work takes more time and requires free space. In that case, it's more convenient to take the appliance to the service center, where it will be disassembled and reassembled without rush. The choice of location depends on the component, so the technician informs you after diagnostics—keep this in mind when planning your day.
Warranty, free diagnostics, and clear terms are what a Beko owner checks before calling a technician. Let's go over what exactly the warranty covers and what the cost of work depends on.
We provide a 1-year warranty on labor and parts. This means that both the completed repair and the installed part remain the service center's responsibility for a year. If after replacing the pump or heating element the machine acts up again, the repeat visit and disassembly are covered under the same warranty, not processed as a new request. In practice, what matters most to a Beko owner is not having to prove whose area it is: the technician's or the installed part's. A warranty on the part separately from the work is needed because some failures are related to the part itself, not the installation; a single term for both eliminates the "who's to blame—the technician or the part" dispute. Ask about the warranty term before work begins—that way you lock in the terms in advance.
Diagnostics are free, and the technician gives you the price after the check — it depends on the component, the fault, and the part needed. The price is quoted before work starts so you can make an informed decision. The same symptom on a Beko can point to different components: the machine won't drain because of a clogged filter, a kinked hose, or a worn pump, and the confirmed cause determines both the scope of work and the part. Beko washing machine diagnostics include checking drainage, water intake, heating, and drum rotation — the technician goes through the components rather than replacing the first thing they guess from your description. It makes more sense to discuss the cost after the inspection, not over the phone: a sum quoted in advance will change anyway once the real cause is clear. That's why we do a free diagnostic first and give you the final price after.
Repairing a Beko washing machine follows a clear logic — from decoding the error code to choosing the component and the repair method. Below are the key takeaways that help you speak the same language as the technician.
85brands
We work with washing machines of every brand sold in Kazakhstan — from Samsung, LG and Indesit to Beko, Haier, Artel and rare imported makes. Can’t find yours in the list? Call anyway — a technician will come and take a look.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
Washing machine error codes are self-diagnostic codes that point to a specific component: drain, water fill, heating, motor, or door lock.
29 January 2026 · 13 minutes read
If your washing machine won't spin, it's usually an unbalanced load, a clogged drain filter or hose, and less often the pump, belt…
19 January 2026 · 12 minutes read
If your washing machine isn't heating water, the heating element or temperature sensor is usually to blame, less often the control board or wiring.
25 December 2025 · 12 minutes read
If your washing machine won't turn on, first check the outlet, extension cord, and the circuit breaker in your panel, then the plug and power cord.
24 November 2025 · 13 minutes read












