Open until 19:00+7 (778) 746 00 26Call a technician
Tech Service technician next to a washing machine

Samsung Washing Machine Repair in Almaty

A technician will come and find the cause of the problem. Diagnostics are free, and the technician arrives within 60 minutes anywhere in the city.

  • 1-year warranty on labor and parts
  • 4 to 20 years of experience

Our own technicians4 to 20 years of experience

Ruslan Ts.Dilmurat S.DimaOraz

Repair prices

  • Diagnostics0 ₸
  • Inlet valve replacementfrom3 000 ₸
  • Clog removal, filter cleaningfrom3 000 ₸
  • Motor brush replacementfrom3 000 ₸
  • Pressure switch (water level sensor) replacementfrom3 000 ₸
All prices
2ГИСЯours4,97 898 reviews
2GIS · Google · Yandex · order database
Common faultsCommon faultsTECH SERVICE02

Common Samsung washing machine faults in Almaty

Below are common symptoms of Samsung washing machines and their likely causes. The technician confirms the exact part during free diagnostics.

PricesPricesTECH SERVICE03

How much Samsung washing machine repair costs in Almaty

The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.

Inlet valve replacementparts not included

1–2 hours

from3 000 ₸

Clog removal, filter cleaninglabour only

1–2 hours

from3 000 ₸

Motor brush replacementparts not included

1–2 days

from3 000 ₸

Pressure switch (water level sensor) replacementparts not included

1–2 hours

from3 000 ₸

Temperature sensor replacementparts not included

1–2 hours

from3 500 ₸

Before and afterBefore and afterTECH SERVICE04

Before and after Samsung washing machine repair in Almaty

Won't drain water, pump hums

1 visittime

from 4,500 ₸cost

Problem
The Samsung washing machine stopped draining water: at the end of the wash it stood with water, the drain pump hummed but did not pump.
What we did
The technician drained the water through the drain filter, removed the old drain pump with a worn, loose impeller, installed a new one, and connected the hose and wires.
Result
Draining and spinning were tested — the machine drains water and spins the laundry, 1-year warranty on the work and on the parts.
I want the same
Ardo washing machine: won't drain water, pump hums — after repairBeforeAfter
01 / 05
All repairs
TECH SERVICE mobile technician with a tool case

How Samsung washing machine repair works at your home in Almaty

From request to performance check — five clear steps.

  1. Requeston the day of request

    Describe the symptom and the machine model so the technician brings the right tools.

  2. Clarifying detailsat request

    Provide the model, error code, and the nature of the noise or leak — the technician will bring the necessary parts.

  3. Approval of workafter inspection

    Work begins only after you approve the cause and the cost.

  4. Repairas agreed

    The technician performs the repair using the necessary tools and parts.

  5. Performance checkafter repair

    The technician checks that the components work after reassembly: a test cycle, no leaks, and no vibration.

Leave a request
TechniciansTechniciansTECH SERVICE05

Our Samsung washing machine repair technicians in Almaty

The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

  • 8 technicians in Almaty
  • 8–12 years of experience in the department
  • Article author Ruslan Ts., 9 years of experience
Technician repairing a washing machine at a customer’s home
Field technician at a customer’s home

The department has 8 specializations — they are listed on the technicians' cards.

01 / 05
Ruslan Ts., washing machine and refrigerator repair technicianexperience9 years

Ruslan Ts.

Washing machine and refrigerator repair technician

Dilmurat S., field technician for washing machine and refrigerator repairexperience10 years

Dilmurat S.

Field technician for washing machine and refrigerator repair

Dima, expert washing machine repair technicianexperience8 years

Dima

Expert washing machine repair technician

Oraz, senior washing machine repair technicianexperience8 years

Oraz

Senior washing machine repair technician

Rustem T., washing machine repair technicianexperience9 years

Rustem T.

Washing machine repair technician

We reply during working hours

Book Samsung washing machine repair in Almaty

Leave a request — the technician will come, and the technician arrives within 60 minutes anywhere in the city.

TECH SERVICE administrator replying to a customer's WhatsApp message

Warranty question? Call us

+7 (778) 746 00 26
Customer reviewsReviewsTECH SERVICE06

Reviews of Samsung washing machine repair in Almaty

Сабина Г.Order No. 564334 · 23 September 2026

ours

Хотел сначала вызвать мастера на дом, потом передумал. Жалоба простая: течёт. Вернули в тот же день, всё функционирует

Repair: washing machine

Богдан С.Order No. 69617 · 14 July 2026

ours

Симптом был очевидный: не отжимает. В techservice попал случайно — и остался. Сказать, что доволен — ничего не сказать.

Repair: washing machine

Айгуль К.Order No. ZK-2025/223 · 11 September 2025

ours

Было важно, чтобы сделали до выходных — гости, то-сё. Уже не верил, что это можно починить. Повод для визита: не сушит. Дима помог выбрать, без навязывания. Могли бы взять больше, но взяли по-божески. Заодно поменяли: тэн. Tech-service посоветовали в чате дома, спасибо им. Второй месяц — полёт нормальный!!

Repair: washing machine

Ксения И.Order No. 819682 · 12 May 2025

ours

Смотрел, у кого есть запчасти на такую модель. Позвонили заранее, предупредили, что задержиться на полчаса. Пользуюсь ежедневно, вопросов нет!!

Repair: washing machine

Аружан К.Order No. 2025-2417 · 24 January 2025

ours

Долго откладывал ремонт, потом всё-таки собрался. Жалоба простая: не сушит. Второй месяц — полёт нормальный.

Repair: washing machine

Ержан А.Order No. TS-1927 · 3 May 2024

ours

С чем пришёл: течёт. Ораз принял, посмотрел и сразу сказал, что делать. Проверили на всех режимах, всё чётко!!

Repair: washing machine

Гаухар Н.Order No. 788281 · 9 October 2021

ours

Прочитал кучу отзывов, половина — реклама, но тут вроде живые. Оставил заявку на ремонт промышленной стиральной машины. Повод для визита: вибрация. Починили и дали гарантию на месяц.

Repair: washing machine

Мирас С.Order No. TS-6433 · 12 March 2021

ours

Алдымен интернеттен іздедім, кейін таныстарым осы жерді ұсынды. Бағасын алдын ала келістік, соңында өзгерген жоқ. Келесіде де осында келемін.

Repair: washing machine

Алмас Д.Order No. ZK-2018/189 · 30 September 2018

ours

Симптом был очевидный: не сушит. Рустем Т перезвонил, когда всё было готово. Гудит ровно, не греется, всё как надо.

Repair: washing machine

Мирас С.Order No. TS-6042 · 15 January 2017

ours

Отдельно спосибо мастеру — Рустем Т, терпения ему хватило. Запчасть была в наличии, доплачивать не пришлось. Проверили при мне, показали, что всё держит

Repair: washing machine
See all reviews
Questions and answersQuestionsTECH SERVICE07

Questions about Samsung washing machine repair in Almaty

Didn’t find the answer? Message us on WhatsApp.

Ask a question
Is it better to repair a Samsung washing machine or buy a new one?

If the tub and body are intact and only the pump, heating element, or drive has failed, repair is usually cheaper than buying new. Replacement makes sense if the tub is cracked or the electronics are seriously damaged, which a technician will confirm after free diagnostics.

Which washing machine brands break down most often, and how does that relate to Samsung repair?

Breakdown frequency depends more on operating conditions and scale buildup than on the brand. On Samsung machines, the drain pump, heating element, and bearing in the sealed tub are the most common failures, so those are the parts that come in for repair.

What is the service life of a Samsung washing machine, and when should it be repaired?

Lifespan depends on the model and load; typically a machine runs for several years before the first major breakdown. If leaks, noise during spin, or display errors appear, repair will extend the unit's life and delay replacing the machine.

Can a Samsung washing machine with an inverter motor be repaired on-site?

Yes, work on the drive, pump, and heating element is usually done on-site if the component is accessible. The machine is rarely taken to the service center, only when the tub needs to be disassembled or the control board requires complex repair.

My Samsung won't drain water and shows an error—is it the pump or a clogged filter?

First check the filter at the bottom front behind the service flap and the hose, and only then the pump. Code 5E or SE also indicates a drain problem, but the exact meaning depends on the model, and the technician checks it against the table.

Why is my Samsung washing machine noisy during spin, and can it be fixed?

Noise during spin is often caused by bearing wear, an unbalanced load, or a loose belt. If the tub is sealed, the bearing isn't replaced separately, but after diagnostics the technician will offer a feasible repair option.

Repair guideArticleTECH SERVICE08

Samsung Washing Machine Repair in Almaty by Tech Service

Ruslan Ts., washing machine and refrigerator repair technician

Author: Ruslan Ts.,Washing machine and refrigerator repair technician

Published
Updated

Tech Service repairs Samsung washing machines in Almaty as a direct contractor, without middlemen. Our technician arrives at your home within 60 minutes anywhere in the city or takes the machine to our service center. Diagnostics are free, you get a 1-year warranty on labor and parts, and our technicians have 4 to 20 years of experience. The technician gives you the price after diagnostics.

Why Your Samsung Won't Drain and What Error 5E Means

“Not draining” is the most common reason to call a technician. Let's break down what 5E means and where to start checking so you don't replace a part unnecessarily.

What Code 5E Means and Why It Appears

  • Code 5E (SE or E2 on some models): on Samsung machines it indicates a drain problem — the machine couldn't pump out water within the allotted time.
  • Drain filter: gets clogged with lint, coins, and small objects, so water drains slowly and the cycle stops.
  • Corrugated hose and pipes: a kink or clog in the hose prevents water from leaving the drum.
  • Pump: the impeller gets jammed with debris; the unit hums but doesn't pump.
  • Electronic module: less often, it doesn't supply power to the pump, so the motor is completely silent.
  • Code meaning depends on the model: the technician checks it against the table for your specific machine rather than blindly treating “by code.”

Filter, Hose, or Pump — Three Causes in Order

  • Drain filter: we start with it — it's at the bottom front behind the service cover, and its clog causes most drain errors.
  • Hose and pipes: then we check the corrugated hose for kinks and clogs, as well as the connections through which water goes to the drain.
  • Pump: only after that do we look at the motor — whether the impeller spins freely and isn't jammed by debris.
  • Why this order: the cause of pump failures is debris and a clogged filter, so a clean filter often restores draining without replacing parts.
  • Replacing the unit: we install a new pump when the impeller is truly stuck or the winding doesn't work.

How to Tell a Pump Failure from a Board Issue

We check a jammed pump not with a multimeter but by seeing whether the impeller spins freely — this more reliably indicates jamming. A multimeter on a stopped motor will show the winding but not a clogged impeller, so the technician first removes the unit and checks rotation by hand. If the impeller spins freely but there's no drain command, we check the power supply from the electronic module to the pump connector. The drain pump doesn't work during water intake, so if the machine isn't filling, looking for the cause in the pump is pointless — we check the inlet valve and mesh. A separate note about the error code: different Samsung generations interpret the same symbol differently, and the technician checks the value against the table for your series. The specialist gives you the price after free diagnostics, once the cause is confirmed — so replacing the pump doesn't turn out to be unnecessary.

What to Do Before the Technician Arrives

While the technician is on the way, the main thing is to avoid flooding your neighbors and damaging the machine. Below are safe DIY steps and what's best left alone until diagnostics.

How to Safely Drain Water Through the Emergency Hose

  • Unplug from power: pull the plug from the socket before any water-related actions — this prevents the pump from starting and accidental heating.
  • Access the hose: open the service cover at the bottom front, lay down a towel, and place a shallow container nearby.
  • Draining: remove the cap from the emergency drain hose, point it into the container, and drain the water while holding the hose with your hand.
  • Watch the temperature: the water may be hot, so keep your hands away from the stream and don't unscrew the drain filter “on the fly.”

What to Prepare for the Technician's Visit

  • Clear access: our technician only needs to reach the machine and a power outlet, so clear the area in front of the door and remove anything from the floor around it.
  • Model plate: take a photo of the model code on the plate — it's used to find the right part by part number if a replacement is needed.
  • Nature of the fault: briefly note at which stage the cycle stops and what code the display shows — this speeds up diagnostics.
  • Water access: make sure the water supply valve is open and can be shut off if the hose needs to be removed.

What not to do yourself

Don't take apart the pump or unscrew the filter while there's water in the drum — that's a direct path to a flood on the floor. The drain pump doesn't run during water intake, so checking it by spinning the impeller before fully draining is pointless, and a multimeter won't show a jammed pump anyway — you check whether the impeller spins freely. Don't touch the electronic module or the board either: without a schematic it's easy to short the traces and turn a small repair into a full unit replacement. Don't remove the front panel or pry off the door seal — on some models this disrupts how parts fit, and reassembling without tools is difficult. If the machine won't drain and shows a code, it's safer to wait for the technician: some breakdowns turn into a unit replacement rather than a single part when disassembled inexpertly.

Won't spin, noisy, stops — motor, imbalance or bearing

The spin cycle is the most demanding stage, and there are several possible causes: from an unbalanced load to the drum bearing. Let's look at how the technician narrows it down and why they don't start by replacing the motor.

Imbalance, drainage, belt or motor

  • Load imbalance: one heavy item has clumped together — the drum won't spin up; we check the distribution and the shock absorbers.
  • Clogged drain: if the water hasn't drained, the spin won't start — we check the filter at the bottom front and the pump impeller.
  • Drive belt: a stretched or slipped belt doesn't transmit rotation; we check its fit before disassembly.
  • Motor: we get to it last, once imbalance, drainage and the belt are ruled out — that way the cause is found without unnecessary replacements.
  • Spin speed: Samsung models typically run at 800–1600 rpm depending on the model, so at high speeds imbalance is more noticeable and easier to distinguish from a motor fault.

Brushes in a brushed motor and inverter drive

  • Brushed motor: brush wear only happens in brushed motors, and that's where the cause of power loss during spin is sought.
  • Inverter drive: an inverter motor has no brushes, so looking for brush wear in such a machine is pointless — the part doesn't exist in the design.
  • Control board: in inverter machines the cause is more often in the electronic module or sensors, not in mechanical wear of the unit.
  • Parts set: inverter and brushed machines require different parts, and this changes diagnostics and part selection by model code.
  • Winding check: the technician tests the windings and checks board signals before condemning the unit to replacement.

Noise during spin and the bearing in a sealed drum

For us, noise during spin most often points to the drum bearing, and this is the longest job because it requires removing the drum and drum assembly. The hum grows with speed, accompanied by drum play and rusty streaks near the door seal. Shock absorbers are checked separately: worn ones cause knocking and drum sway, but not a hum. In a sealed drum the bearing isn't replaced separately, so the technician explains upfront which repair option is possible for your model — sometimes it's replacing the drum assembly. In a serviceable drum the bearing is replaced as a separate part. The cause of noise should be distinguished from a knock from a foreign object in the drum — a coin or bra wire makes a completely different sound. If the hum appeared recently, don't delay diagnostics: a worn bearing damages the shaft, and the job becomes more expensive.

Won't fill, won't heat, leaks from below — other common faults

These symptoms are less often related to electronics and more often to water and heating. We've put them in a table 'symptom → cause' so you can see where the check begins.

Table of symptoms and first causes

SymptomFirst causeSecond causeWhat we check
Not filling with waterwater supply tapinlet hose mesh filtervalve and mesh filter
Not heating waterheating elementtemperature sensorheating and sensor
Leaking from the bottomhoses and pipesdrain pumpconnections and pump
Leaking from the frontdoor seal—door gasket

Not heating water — heating element or temperature sensor

For most brands, we replace the heating element without removing the tank, so checking the heating takes less time than it seems. First, the technician measures the heater's resistance and compares the temperature sensor readings: a working element transfers heat to the water, while a faulty sensor gives a false "not heating" signal even when the heater works. Hard water and scale speed up wear on the heating element — a layer of deposits prevents heat from transferring to the water, and the part overheats. On some models, a separate code signals the problem, and its meaning depends on the model — the technician checks it against the table for your machine. If "not heating" complaints recur, check the heater's condition as well, not just the sensor: replacing only the sensor when the heating element is scaled up brings back the same fault after a few washes.

Leaking from the bottom — hoses, pump, or pipes

  • Hoses and pipes: they most often cause bottom leaks — cracks in the rubber and loose clamps are visible after removing the side panel.
  • Drain pump: water collects under the pump if the seal is worn or debris — coins, lint — gets into the housing.
  • Door seal: leaks from the front, not the bottom — the leak location already shows where to check.
  • Connections: the technician looks at where moisture collects — dry areas immediately rule out half the possibilities.
  • Inlet path: a loose clamp on the inlet hose causes a thin stream along the back wall, easily mistaken for a tank leak.
  • Check order: from simple to complex — first clamps and hoses, then the pump, and only then disassembling the tank.

How the technician finds the cause and selects the part

Good diagnostics means narrowing down the causes, not replacing everything in sight. Here's how the technician pinpoints the exact component and the right part.

How the cause is determined when the machine stops mid-cycle

When a machine stops mid-cycle, our technician most often checks the drain, imbalance, and motor, and considers the control board as one possible cause but not the main one. First, he checks whether the drain pump impeller spins freely and if the filter is clogged, then whether the laundry load has shifted and how the shock absorbers behave during the spin cycle. Next come the belt, the brushes of the commutator motor, and the motor windings. The electronic module is opened last: it fails from voltage surges less often than people think, and suspecting it first means replacing a working part. This order prevents blaming everything on electronics: most stops are due to drainage or overloading, and the board suffers from voltage surges less often than it seems.

Selecting a part by model code

  • Model code on the nameplate: the label with the series designation is attached to the body — on many machines it's visible in the loading door.
  • Part number: for the pump, heating element, or sensor, we verify the part number against the manufacturer's catalog, not by the component's appearance.
  • Model generation: parts for early and late series differ in fit, so the same component won't fit different production runs.
  • Check before installation: we compare connectors and mounts with the original part to avoid installing a "almost fitting" one.
  • Exact selection by code: eliminates the part that would require redoing the work and saves a repeat visit.

Myths that hinder diagnostics

Three common myths — "the pump can be seen with a multimeter," "the bearing can be replaced in a sealed tub," and "inverter motors wear out their brushes" — are actually false and lead diagnostics astray. A multimeter won't show a jammed drain pump impeller: you check whether it turns freely by hand. In a sealed tub, the drum bearing isn't replaced separately — the part comes as a single unit. Brushes are only found in brushed motors; inverter drives don't have them, so looking for brush wear there is pointless. Another myth is that the drain pump runs while the machine is filling: it doesn't start during fill, and the cause is sought in the valve or filter mesh. Checking based on facts, not myths, saves you from replacing working components and reduces the number of repeat visits.

How Tech Service handles repairs

Here's how the repair itself works: who comes, what happens during diagnostics, and what you get after the job. No surprises along the way.

60-minute arrival and free diagnostics

Our technician arrives at your home within 60 minutes anywhere in the city, and diagnostics are free — based on the results, he tells you the cause and the cost. First he inspects the machine, checks draining, water intake, and drum rotation, then matches the error code with the table for your Samsung model — the code's meaning depends on the specific generation. If the cause is a clogged filter or a kinked hose, he fixes it on the spot; if a pump or heating element needs replacement, he explains which component failed and why. This approach lets you decide whether to repair the appliance knowing the cause, rather than paying for a blind check. Our Samsung washing machine repair in Almaty starts with exactly this kind of free on-site diagnostics. In our experience, free diagnostics most often answers the owner's main question — whether it's worth fixing the machine at all.

1-year warranty on labor and parts

We provide a 1-year warranty on labor and parts, so the replacement of a component remains our responsibility even after the repair. The installed pump, heating element, or temperature sensor is covered by the warranty together with the work performed — not separately for labor and separately for the part. A warranty on parts separate from labor matters because some failures don't show up immediately but after several wash cycles: the new component must perform under real conditions, not just at the moment of installation. The technician who came to you remains the same person you can turn to with a question about this machine. In my view, this is the main difference of a responsible service — not losing the thread after the money is paid.

Direct contractor and you can pay via Kaspi QR, Kaspi Red, bank card, cash or bank transfer for companies

  • Direct contractor: Tech Service is not an aggregator or intermediary — our technician does the repair, and he is also responsible for the result.
  • Experienced technicians: our specialists have 4 to 20 years of experience and know the design of different Samsung generations.
  • One technician from request to completion: we take the request, the technician comes to you, and he performs both diagnostics and repair.
  • Payment methods: we accept payment in any convenient way, with no surcharges for passing the request to third parties.
  • Straight talk about the cause: the technician names the cost and cause of the breakdown after free diagnostics, discussing them directly with you.
  • Responsibility for the result: the 1-year warranty on labor and parts is backed by the same technician who was at your home.

Samsung washing machine repair essentials

Breaking down the codes, common causes, and repair sequence reduces Samsung washing machine repair to a few checks — from simple to complex. Below is a brief summary of what most often determines the outcome.

  • Code 5E (SE, E2): on Samsung it indicates a drain problem, but the meaning should be checked against the table for the specific model — different generations interpret the same code differently.
  • Check order for “not draining”: first the filter, then the hose, and only then the pump; the pump is assessed by whether the impeller spins freely, not with a multimeter.
  • What to do before the technician arrives: drain the water through the emergency hose behind the service flap at the bottom front, placing a towel underneath — the water may be hot.
  • Motor and tub: brush wear occurs only on brushed motors, and the bearing in a sealed tub is not replaced separately.
  • Part by model code: precise part selection combined with the “simple to complex” principle reduces unnecessary replacements and repeat disassembly.

85brands

Besides Samsung, we repair other washing machine brands in Almaty

We work with washing machines of every brand sold in Kazakhstan — from Samsung, LG and Indesit to Beko, Haier, Artel and rare imported makes. Can’t find yours in the list? Call anyway — a technician will come and take a look.

We also repairWe also repairTECH SERVICE09

Besides Samsung washing machine repair, we fix other equipment in Almaty

Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.

BlogBlogTECH SERVICE10

Worth reading before Samsung washing machine repair in Almaty

Leave a review

Choose a platform — the TECH SERVICE page will open.

2ГИС2GISGoogle MapsЯYandex Maps
Send a review with photos on WhatsApp