experience9 yearsRuslan Ts.
Washing machine and refrigerator repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 746 00 26Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Free diagnostics, 1-year warranty on labor and parts.
Our own technicians4 to 20 years of experience




Repair prices
Below are typical symptoms and likely causes.
Clogged filter, kinked hose, pump
from3 000 ₸
Closed tap, clogged mesh filter, valve
from3 000 ₸
Load imbalance, water, belt
from3 000 ₸
Hoses, pump or connections
from4 500 ₸
Burned-out heating element or temperature sensor
from3 500 ₸
Imbalance, shock absorbers, bearing
from5 000 ₸
The code points to draining, filling, or heating
from4 500 ₸
The motor's graphite brushes wear down
from3 000 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1 visittime
from 3 000 ₸cost

BeforeAfter5 steps

From request to performance check — five steps.
Leave a request and a technician will arrive within 60 minutes anywhere in the city.
The technician comes with their own tools and test equipment and works on-site at the machine.
The owner confirms the scope of work and the part the technician will replace.
The technician replaces the faulty component right at your place without taking the machine away.
Runs a test cycle and provides a 1-year warranty on labor and parts.
The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsExpert washing machine repair technician
experience8 yearsSenior washing machine repair technician
experience9 yearsWashing machine repair technician
We reply during working hours
Describe the symptom and your machine model — a technician will arrive within 60 minutes anywhere in the city.

Warranty question? Call us
+7 (778) 746 00 267 898 reviews of repairs at TECH SERVICE in total
Данияр С.Order No. 2025-3853 · 7 August 2025
oursПробовал найти мастера в своём районе, но все были заняты. Симптом был очевидный: не отжимает. Включил, проверил, работает
Акбота Т.Order No. TS-2305-226 · 6 November 2023
oursЦена имела значение, но и гарантия тоже. Симптом был очевидный: ошибка на дисплее. Внешне как новый, если не считать мелкой царапины!!
Индира П.Order No. 2023-3911 · 14 June 2023
oursС чем пришёл: течёт. Дильмурат С взялся за то, от чего другие отказались. Работает как раньше, придирок нет.
Сергей Р.Order No. TS-2210-605 · 29 November 2022
oursДруг посоветовал, у него похожая история была. Повод для визита: вибрация. Крутит ровно, без рывков
Наталья С.Order No. 107334 · 4 July 2021
oursПозвонил в три места, здесь единственые назвали цену сразу. Работает как раньше, придирок нет.
Станислав К.Order No. TS-4180 · 28 January 2018
oursТехника на гарантии уже не была, так что выбор был свободный. Руки чесались починить самому, хорошо, что не полез. Жалоба простая: течёт. Дильмурат С не стал навязывать дорогую запчасть, поставил нормальную. Деталь на замену — подшипник. Всё оформили по договору, с печатью. Смета совпала с итогом, что редкость. Хороший сервис, побольше бы таких. Сказать, что доволен — ничего не сказать.
Малик Т.Order No. ZK-2017/348 · 18 September 2017
oursКүтуге уақытым жоқ еді, сол күні алып кеттім. Тексеру кезінде бәрін өзі көрсетті. Бағасын алдын ала келістік, соңында өзгерген жоқ. Қосымша бөлшек қажет болды, бірақ бағаны көтермеді. Кепілдік берді, бұл мен үшін маңызды. Бір күнде жөндеп берді, кешіктірмеді. Кәсіби мамандар, рақмет.
Елдос К.Order No. ZK-9793 · 17 June 2017
oursХотел сначала вызвать мастера на дом, потом передумал. Ремонт промышленной стиральной машины — вот с этим и пришёл. Основная жалоба — не греет воду. В списке работ — тэн. Сказали 17 500, а потом ещё и скидку сделали. Второй месяц — полёт нормальный
Богдан С.Order No. 95121 · 11 December 2016
oursПробовал найти мастера в своём районе, но все были заняты. До последнего откладывал, но пришлось признать: не сушит. Поставили новую деталь: насос. Мастер сразу сказал, что к чему, без размытых формулировок. Проверили при мне, показали, что всё держит.
Ксения И.Order No. 80442 · 12 March 2016
oursБыло подозрение, что дело в плате, хотелось услышать второе мнение. Первое, что заметил: не включаеться. Включил, проверил, работает.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionWith a sealed tub, the bearing isn't replaced separately — you need a new tub assembly with the drum, and that depends on the model. The technician will tell you after a free diagnosis whether such a replacement makes sense.
Brush wear is only possible in brushed motors: the machine loses power, the drum spins in jerks, and there's a crackling sound during the spin cycle. Models with an inverter motor don't have brushes, so the cause is sought elsewhere.
Water floods the floor, can reach the wiring and cause a short circuit, and constant moisture speeds up corrosion of components. It's better to stop washing and call a technician: a free diagnosis will show exactly where the leak is.
The drum will stay full of water, the spin cycle won't start, and the pump will run dry and may fail completely. Most often the cause is a clogged filter or hose, less often the pump itself — that's what the technician checks.
Yes, if overloaded or if the laundry clumps together, the imbalance protection kicks in and the spin cycle won't start. If after evenly loading and checking the drain the machine still hums and won't spin, the cause is sought in the belt, drain, or motor.
The time depends on the breakdown and model: some work the technician does on site, while replacing the bearing with tub disassembly is the longest procedure. The technician will give a more precise estimate after a free diagnosis when they identify the cause.
Tech Service repairs Midea washing machines in Almaty with its own technicians who have 4 to 20 years of experience. A technician arrives at your home within 60 minutes anywhere in the city or accepts the machine at the service center. Diagnostics are free, and we provide a 1-year warranty on labor and parts. The technician gives you the price after diagnostics.
Drain problems are the most common reason to call a technician for a Midea washing machine. Let's break down what code E18 or F18 means, what to check first, and how to safely drain the water before the specialist arrives.
The code E18 or F18 (d02 on some models) indicates a drain problem, and the technician checks its meaning against the table for the specific Midea model before naming the cause. This code usually points to three components: the drain filter, the drain hose, and the drain pump. The drain pump doesn't work during water fill—it only turns on during the drain phase, so the error appears at the end of the cycle when the drum is still full of water. Debris like coins, lint, and small objects clog the impeller, and the pump hums but doesn't pump. We don't treat the machine blindly based on a single code. The same code on different Midea generations can mean a different component, so "treating by code" without checking the model table is a common cause of repeat calls.
For drain problems, we go from the common and simple to the complex: first the drain filter at the bottom front behind the service flap, then the hose, and only then the pump. On Midea, the drain filter is located at the bottom front behind the service flap—you unscrew it after the water has been drained. The hose is checked for kinks and clogs along its entire length up to the connection point to the sewer. The drain pump gets clogged with debris—coins, lint, small objects—and a clogged filter increases the load on the pump. A multimeter won't show a jammed pump: the technician checks whether the impeller spins freely. That's why cleaning the filter extends the life of the component—it reduces the load on the pump and lowers the risk of a repeat drain error.
No water fill and no heating are two different chains of causes. We'll show what the technician checks in each case and why access to a specific component matters on Midea.
When there's no heating, we check the heating element and the temperature sensor: on Midea, the heater is located at the front, so the technician removes the front panel and reaches the unit without disassembling the entire machine. If the wash cycle runs but the water stays cold, the culprit is either a burnt-out heater or a sensor that reads the temperature incorrectly and doesn't trigger heating. In such cases, Midea washing machine repair starts with testing both elements so we don't replace a working part. We select the replacement by part number or model code to ensure the new heater matches in fit and power. On most brands, the heating element can be replaced without removing the drum, so replacing the heater is one of the fastest operations—not a reason to haul the machine to a service center. Our technicians' experience shows that a burnt-out heater is more common, but the sensor can sometimes produce the same symptoms.
Failure to spin and stopping mid-cycle are symptoms that point to several different components; let's break down how we distinguish an imbalance from a motor fault and why the control board isn't the first suspect.
If your Midea stops mid-cycle, it's most often due to drainage, imbalance, or the motor, while the control board is one possible cause but not the main one. The machine interrupts the program when a sensor detects that water isn't draining or the drum isn't reaching the required speed—the electronics are just following protective logic. We check the drain filter at the bottom front behind the service flap, whether the pump impeller turns freely, and if the laundry is tangled in the drum. After that, we inspect the motor: on brushed motors we check the brushes; inverter motors don't have them. We examine the control board last—its failure is less common than mechanical causes. Before testing the electronics, we rule out drainage and imbalance: they cause stops more often and cost less to fix than replacing the board.
Brush wear is only possible on brushed motors; inverter motors don't have brushes, so looking for them there is pointless. On a brushed machine, wear shows up as sparking, reduced spin power, and jerking when the drum accelerates—the motor seems to lose traction under load. You can determine the motor type from the model's documentation or by the machine's behavior: an inverter unit runs smoother and without the characteristic crackling. Brush replacement is part of servicing the motor itself, not the electronics, and wear is assessed after disassembling the unit. If a technician immediately suggests "replacing the brushes" on a machine with an inverter motor, it's worth clarifying which motor your Midea model has—inverter units have their lifespan determined by other parts.
A leak from the bottom and a leak from the front at the door are different components. We'll show what the technician checks in each case and why bearing replacement is the longest job in servicing.
If water leaks from the bottom of a Midea, we check the hoses, drain assembly, and lines; a leaking door seal shows up at the front by the door, not under the machine. The hoses connect the tub to the pump and valve, and a loose clamp on them causes drips under the machine, not at the door. The drain assembly sits at the bottom front behind the service panel: its housing and seal are inspected along with the impeller, which is checked by hand for free rotation. The inlet hose and its connection to the body can leak, which shows up when filling. A leak from the bottom is often due to a loose clamp or a clog putting pressure on a connection, so the technician checks the joints first rather than replacing a part right away. Before inspection, unplug the machine and drain the water through the emergency drain hose behind the service panel at the bottom front, placing a towel underneath—the water may be hot.
The drum bearing is replaced only if the tub is split; on a sealed tub this part is not replaced separately, and that determines the scope of work. On a split tub, the technician separates the halves, presses out the old assembly, installs a new one, and reassembles with sealant. On a sealed tub, the bearing is not replaced separately—the assembly comes as a unit, and that's a different scope of work. Noise during spin, a hum that grows with speed (usually 800–1600 rpm depending on the model), and drum play are reasons to check it, not the belt. Bearing replacement is the longest job in washing machine service because it requires removing the tub and drum, so the technician explains in advance whether your Midea model has a split tub. We state this before work begins so you understand exactly what you're paying for.
| Symptom | What we check first | Assembly | Scope of work |
|---|---|---|---|
| Won't drain | filter, hose, pump | drain assembly | from filter cleaning to replacement |
| Won't fill with water | faucet, screen, valve | inlet valve | from screen cleaning to valve replacement |
| Won't heat | heating element, temperature sensor | front heating element | replacement without removing the tub |
| Won't spin | imbalance, drain, belt, motor | drive belt, motor | from adjustment to motor replacement |
| Leaks from the bottom | hoses, pump, lines | hoses and lines | from tightening clamps to replacement |
| Noisy during spin | bearing, tub | drum bearing | the longest job if the tub is split |
Here's what happens from request to warranty: how a specialist pinpoints the cause, why the price is quoted after diagnostics, and what the warranty on labor and parts covers.
We service Midea appliances at the customer's home or in our shop, and we source parts by part number or model code so we don't replace a component blindly. Our technician comes to your home, and most common jobs — draining, filling, heating — are done on site; the machine is taken to the shop only when the tank needs to be split or the bearing replaced, which is the longest job on this brand. We look up the part by its number or by the model code on the machine's rating plate, not by a photo from an ad. Matching by model code matters for Midea: different generations of the same line can use different parts, and a lookalike part from the market leads to another breakdown after a few washes — so we double-check the markings before installation. This is how Midea washing machine repair in Almaty is built on precise checks of components, not guesswork.
We provide a 1-year warranty on labor and parts, and if the same error returns after service, that's a reason to contact us again under warranty. The same error coming back is usually because the symptom was fixed, not the cause: the technician replaces the failed part but doesn't check the whole chain of the component — for example, installing a new pump when the filter or hose is clogged. That's why during diagnostics we check not only the component indicated by the code but also everything connected to it: filter, hose, wiring, sensor. The warranty covers both labor and the installed part — if the same error returns, our technician comes again and figures out why the cause remained. In my view, it's this follow-up visit that separates proper repair from replacing a part blindly.
Midea washing machine repair comes down to precise diagnostics of the component and checking the code against the table for the specific model — below are the main takeaways on common breakdowns.
85brands
We work with washing machines of every brand sold in Kazakhstan — from Samsung, LG and Indesit to Beko, Haier, Artel and rare imported makes. Can’t find yours in the list? Call anyway — a technician will come and take a look.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
Washing machine error codes are self-diagnostic codes that point to a specific component: drain, water fill, heating, motor, or door lock.
29 January 2026 · 13 minutes read
If your washing machine won't spin, it's usually an unbalanced load, a clogged drain filter or hose, and less often the pump, belt…
19 January 2026 · 12 minutes read
If your washing machine isn't heating water, the heating element or temperature sensor is usually to blame, less often the control board or wiring.
25 December 2025 · 12 minutes read
If your washing machine won't turn on, first check the outlet, extension cord, and the circuit breaker in your panel, then the plug and power cord.
24 November 2025 · 13 minutes read












