experience9 yearsRuslan Ts.
Washing machine and refrigerator repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 021 13 16Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
Technician arrives within 60 minutes anywhere in the city. Free diagnostics, 1-year warranty on labor and parts.
Our own technicians4 to 20 years of experience




Repair prices
Below are eight common symptoms. The cause is identified after free diagnostics, and the technician gives you the price at the same time.
dirty contacts, adapter, worn battery
from4 500 ₸
sensor failure, dirty lidar, low battery
from5 500 ₸
clogged hose, faulty pump, valve
from8 500 ₸
object stuck in brush, stretched belt, motor
from5 000 ₸
dirty lidar, sensor failure, firmware
from4 000 ₸
debris in wheel, worn bearing, brush
from3 500 ₸
code points to a component, needs inspection
from4 000 ₸
low battery, sensor failure, dirty contacts
from5 500 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1–2 daystime
from 3 500 ₸cost

BeforeAfter5 steps

From request to final check — five steps, free diagnostics.
Describe the symptom and robot model so the technician brings the right tools.
The technician arrives anywhere in the city within 60 minutes of your request.
The technician finds the cause of the fault and determines the necessary work.
You approve the list of work and parts; repair starts only after that.
The technician checks the device and provides a 1-year warranty on labor and parts.
The home appliance repair department in Almaty has 8 technicians with 8 to 12 years of experience.

The department has 8 specializations — they are listed on the technicians' cards.
experience9 yearsWashing machine and refrigerator repair technician
experience12 yearsGeneral household appliance repair technician
experience10 yearsField technician for washing machine and refrigerator repair
experience8 yearsExpert washing machine repair technician
experience8 yearsField refrigerator repair technician
experience8 yearsSenior washing machine repair technician
experience11 yearsDishwasher repair technician
experience9 yearsWashing machine repair technician
We reply during working hours
You can request service through the website form or by phone. Just tell us the robot model and describe the symptom — that's enough for the technician to schedule a convenient time.

Warranty question? Call us
+7 (778) 021 13 167 898 reviews of repairs at TECH SERVICE in total
Богдан С.Order No. TS-5515 · 17 December 2024
oursБольше всего напрягало: не заряжается. Отдельно спасибо мастеру — Рустем Т, терпения ему хватило. Работает даже тише, чем до поломки.
Артём К.Order No. ZK-2024/166 · 26 May 2024
oursЗаметил случайно: не заряжаеться. Рустем Т снял деталь, показал износ, вопросов не осталось. Ни копейки сверху, как и обещали. Деталь на замену — аккумулятор. Посмотрели, назвали срок — два дня. Сказать, что доволен — ничего не сказать.
Павел Ш.Order No. TS-6295 · 29 July 2022
oursПервое, что заметил: кружит на месте. Рустем Т помог выбрать, без навязывания. Уже полгода — ни одного сбоя.
Аскар Ж.Order No. 2020-9710 · 2 December 2020
oursПозвонил в три места, здесь единственые назвали цену сразу. Уже полгода — ни одного сбоя.
Санжар О.Order No. TS-2001-243 · 25 May 2020
oursДамир М помог выбрать, без навязывания. Заявку приняли по телефону, перезвонили через десять минут. Работает как раньше, придирок нет!!
Ольга М.Order No. ZK-2020/271 · 6 February 2020
oursСмотрел, у кого есть запчасти на такую модель. Такое чувство, что техника сговорилась ломаться вся разом. Проблема — кружит на месте. По деньгам вышло адекватно, в другом месте просили больше. Приняли без очереди, оформили за пять минут. Разобрали, посмотрели: мотор. С чистой совестью советую. Сделали и забыл про проблему.
Артём К.Order No. 2018-3621 · 26 August 2018
oursПозвонил знакомому, он раньше работал в сервисе, посоветовал этих. Больше всего напрягало: не заряжается. Ребёнок уже проверил на прочность, держится
Ольга М.Order No. 984581 · 2 April 2018
oursТелефонмен кеңес сұрадым, тегін айтты. Жөндеуге кепілдік бар, сол сенімді.
Азамат Е.Order No. 2017-4595 · 23 July 2017
oursБыло важно, чтобы сделали до выходных — гости, то-сё. Привёз на диагностику: робот-пылесос. Первое, что заметил: кружит на месте. Отдельно скажу про мастера: Рустем Т — спокойный, без лишней суеты. Позвонили заранее, предупредили, что задержится на полчаса. По деньгам вышло адекватно, в другом месте просили больше. Мастер показал, что меняет: аккумулятор. Ребёнок уже проверил на прочность, держится!!
Юлия А.Order No. TS-2097 · 17 January 2016
oursЦена имела значение, но и гарантия тоже. Вечером включил — и всё стало ясно: не заряжается. Мастер показал, что меняет: мотор. Посмотрели, назвали срок — два дня. Починили и дали гарантию на месяц.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionIf the damage is serious and repair isn't worth it, look at budget models with decent navigation and service support in the country. But often it's cheaper to fix a Roborock: a technician during free diagnostics will tell you whether repair is justified or it's easier to buy a new one.
Good models cost noticeably more than budget ones, so when a component breaks, repair is usually more cost-effective than a new purchase. The decision depends on the model and condition of the device: after diagnostics, the technician will explain what's cheaper in your case.
Yes, in many cases the board can be restored if you don't power it on immediately after moisture exposure. Dry the body, don't turn the robot on or place it on the base, and a technician will check the board and contacts during free diagnostics.
Blinking usually indicates a problem with contacts, the power supply, or the battery, but the interpretation depends on the model. Before the technician's visit, wipe the contacts on the robot and base and check if the station is plugged in.
Error 8 is related to the turbine fan operation, and the exact cause is shown by diagnostics, as the interpretation depends on the model. You can check the filter and air duct for clogs yourself, but then you need a technician.
Yes, the wheel drive and the wheels themselves are repairable, although the scope of work depends on the model. A crooked trajectory can also be caused by sensors or calibration, so a technician during free diagnostics will determine what exactly to replace or adjust.
Tech Service repairs Roborock robot vacuums in Almaty as a direct service provider: our technician comes to your home or the device is repaired at our service center. Diagnostics are free, there's a 1-year warranty on labor and parts, and a technician arrives within 60 minutes anywhere in the city. The technician quotes the price after diagnostics.
Your robot's behavior is a signal, not a verdict. Let's break down what typical symptoms and error codes mean and how a technician traces them to the real cause.
An error code on the screen or in the Roborock app points to the unit where protection tripped, but it doesn't name the specific part to replace. Error 8 indicates a suction problem, but it doesn't tell you whether the cause is a clogged airway, a worn turbine, or a sensor. It's similar with wheel and navigation codes: the control board registers that protection tripped, and the sensors only report that a parameter is out of range. The same error number can point to a simple clog or motor wear—the difference only becomes clear during disassembly. That's why during free diagnostics we check the chain of components rather than replacing a part based on the error code. The technician quotes the price after free diagnostics, once the cause is identified. If you need Roborock robot vacuum repair in Almaty and your robot is showing an error, the technician starts by checking the components in sequence. The logic of tracing from code to part stays the same—the approach is identical.
Noise and weak suction are usually related to the turbine and a clogged filter, while app issues are typically about Wi-Fi settings or firmware, not hardware. The turbine creates suction during cleaning, and when its impeller is clogged with dust or worn, the hum increases and airflow drops. A clogged filter has the same effect—the motor runs at its limit trying to pull air through the blockage. With the app it's different: if the robot stopped connecting, the cause is usually the network or a firmware glitch, not the control board. When the device loses connection after a router change, it's not a breakdown yet—first check the network and re-pair it in the app, and only then look at the control board.
Roborock has a limited set of components that fail. Here's exactly which ones the technician inspects and replaces—from the battery to the navigation sensors.
The battery, control board, and wheel drive motors are the three components that most often explain why the robot won't hold a charge, won't move, or behaves erratically. The board controls the motors, sensors, and charging, so it's the first thing we inspect for any behavioral issue. Battery capacity drops gradually: first cleaning time shortens, then the device stops mid-room and doesn't make it back to the base. Drive motors wear out from constant turns on carpets and thresholds—play, humming, and jerking appear during movement. Our technician tests all three components together, because the symptom "won't move" can be caused by a discharged battery, a burnt trace on the board, or a jammed gearbox. When the wheels wear, the robot drives crooked long before the drive fails completely, so motor replacement is planned based on tread condition, not on the fact that it stopped. The cost of Roborock robot vacuum repair is quoted by the technician after free diagnostics—the final price depends on which of the three components needs attention.
Roborock robots can be restored after water exposure if the control board and contacts were immediately de-energized and the robot was not turned on again. Moisture on the board triggers corrosion of traces and short circuits between contacts — the sooner the device reaches a technician, the better the chance of fixing it with cleaning alone. We disassemble the housing, dry the module, remove oxidation from the board and contact pads, and check traces for breaks. If water got into the battery compartment, we test the battery separately — a wet cell loses capacity and holds charge poorly. The main mistake owners make is trying to turn the device on "to see if it works": under voltage, oxidation on the board spreads, and instead of replacing contacts the technician has to replace the whole module. So after a spill, dry the robot and take it for diagnostics rather than testing it with the power button.
| Component | What we check | Work options |
|---|---|---|
| Battery | capacity, whether it holds charge | replacement |
| Control board | signs of moisture, oxidation, traces | cleaning or replacement |
| Wheel drive motors | wear, movement, play | motor replacement |
| Turbine | clogs, noise, airflow | cleaning or replacement |
| Charging contacts | oxidation, fit on the base | cleaning or replacement |
| Navigation sensors | contamination, response | cleaning or replacement |
Different Roborock series have different components and error logic, so the technician confirms the model before the visit — this determines which parts to bring and what to check first.
The S-series and Q-series Roborock have different brush drives and board layouts, so we diagnose and replace components with the specific model in mind. On the S7 and Q7 Max, the harnesses to the turbine and charging contacts are routed differently, and the control board sits in a separate compartment — this changes the inspection order during disassembly. On models with a self-cleaning base, some "robot failures" actually relate to the base itself: suction, water drainage, and container lifting are checked separately. We repair Roborock robot vacuums in Almaty considering both parts of the pair, because an error on the app screen often points to the base rather than the robot. On models with a self-cleaning base, the technician checks both devices, not just the robot — this eliminates half of false diagnoses.
We accept older discontinued Roborock models for repair and restore them based on the condition of their components, not the year of manufacture. The battery, control board, wheel drive motors, and turbine wear differently, so a working unit from an older series can match a newer one in service life. We disassemble the robot, assess wear by component, and state what needs replacement and what can be restored. For a discontinued model, after diagnostics the technician says which components can be restored — so the owner can decide whether the repair is justified. Our diagnostics are free, so the decision is based on the actual condition of the device, not guesswork. If restoring by components costs more than it's worth, the technician will say so directly.
If your Roborock stops connecting to the app after you change your router, it's usually a network setting issue, not a board failure. The robot can't see the new network, drops out of the app, or gets stuck during pairing — the control board is fine and just waiting for the correct data. Robots operate on the 2.4 GHz band, so a new dual-band router often "hides" the network: your phone is on 5 GHz while the robot looks for 2.4 GHz and can't find it. Re-pairing to the 2.4 GHz network solves the problem without repair; sometimes you just need to switch your phone to that frequency and go through pairing again in the Roborock app. Updating the firmware through the app is also part of this check. If the robot still won't connect after re-pairing, then we look at the Wi-Fi module on the board.
Some requests are resolved without a specialist, while others require a technician visit. Here's what checks you can do yourself and how the process works from request to return of your device.
Restoration makes sense when one or two components are replaced and the body, control board, and navigation are intact. Replacing the battery or turbine gets the device working again, while damage to several key modules at once is a reason to discuss a new robot vacuum. Technicians with 7 to 20 years of experience assess the condition of components during free diagnostics and list the work needed rather than pushing replacements. The technician gives the price after free diagnostics, once it's clear which components need attention. The owner makes the decision: we show which parts need attention and leave the choice to them. If repairing a Roborock robot vacuum in Kazakhstan costs more than replacing several modules at once, it's more honest to say so directly and not take on the job.
In the Almaty robot market, there are three types of service providers: aggregator services, private technicians, and direct providers. Let's look at how they differ for the owner and what terms we offer for device servicing.
Tech Service is a direct service provider: your robot is handled by our own technician, not by a middleman who passes it on to a third party. A service aggregator collects requests and distributes them among contractors, so the owner never knows in advance who will take on the device or how they will be accountable for the result. A private technician works independently but relies on their own resources and doesn't always take on control boards or wheel drive motors. Our service keeps both areas in one team: technicians with 7 to 20 years of experience handle everything from simple cleanings to electronics replacement. Going to a direct service provider in Kazakhstan means one point of contact throughout the device's journey — from intake to return — and the same person who handled the device is accountable for it. The technician quotes the price for Roborock robot vacuum repair after free diagnostics — no work starts before that.
We send our technician to your home or accept the device at our service center. A home visit is convenient when the robot can't find its base, loses its route, or won't connect to the app: these issues are often resolved on the spot without transporting the device. At the service center, it's easier to replace the control board, wheel drive motors, and turbine — the technician tests the unit in operation. The owner chooses the format based on the nature of the fault and their schedule. Before the visit, we confirm the model and symptom so the technician arrives prepared and doesn't waste time guessing on site or doing unnecessary teardowns. If the symptom points to the control board, the technician brings the right tools and checks the unit along the chain — from contacts to traces.
Here's what a Roborock owner should keep in mind before contacting a service center: how breakdowns work, the typical components, and the line between setup and repair.
38brands
Our technicians repair Roborock robot vacuums and other models that have dedicated brand pages on the site.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your dishwasher won't drain, the most common culprits are a clogged filter or drain hose; less often, it's the pump, impeller…
24 March 2026 · 12 minutes read
A washing machine can hum for many reasons, and the first thing to figure out is when the sound appears.
20 March 2026 · 12 minutes read
If your washing machine isn't filling with water, the most common culprits are a closed valve, a clogged inlet filter screen on the hose…
20 February 2026 · 13 minutes read
If your microwave isn't heating but the light and turntable still work, the problem is usually one of the high-voltage components — the magnetron, diode…
15 February 2026 · 12 minutes read
If your refrigerator stops working, first check the outlet, the power cord, and the thermostat setting, and after defrosting let it stand for a while.
4 February 2026 · 12 minutes read
Washing machine error codes are self-diagnostic codes that point to a specific component: drain, water fill, heating, motor, or door lock.
29 January 2026 · 13 minutes read












