experience10 yearsVasiliy Z.
Senior TV repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 021 13 16Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
Free diagnostics, a technician at your door within 60 minutes anywhere in the city. 1-year warranty on labor and parts.
Our own technicians4 to 20 years of experience




Repair prices
Below are typical symptoms and likely causes. The technician confirms the exact cause after diagnostics.
power supply, fuse, or power button
from8 000 ₸
backlight, inverter, or panel
from9 500 ₸
panel ribbon cable, T-CON board, or the panel itself
from9 500 ₸
batteries, IR receiver, or control board
from9 000 ₸
speakers, amplifier, or settings
from8 000 ₸
overheating, power supply, or board
from8 000 ₸
Wi-Fi module, firmware, or router
from9 000 ₸
control board, backlight, or panel
from7 000 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1 visittime
from 8 000 ₸cost

BeforeAfter5 steps

Five steps from request to checking the TV after repair.
Describe the symptom and TV model so the technician brings the right tools.
The technician arrives anywhere in the city within an hour after confirming the request.
The technician uses measuring tools and test signals, and shows you the defect on the screen.
You decide whether to repair now or later; the technician starts after you agree.
The technician cleans up, returns the old part, and notes the work done.
The digital device repair department in Almaty has 7 technicians with 7 to 18 years of experience.

The department has 7 specializations — they are listed on the technicians' cards.
experience10 yearsSenior TV repair technician
experience10 yearsTV board repair technician
experience10 yearsElectromechanical technician
experience13 yearsAudio and DVD repair technician
experience18 yearsSmartphone repair technician
We reply during working hours
What to include in your request so the technician comes prepared: model, symptom, TV age, and where it's located.

Warranty question? Call us
+7 (778) 021 13 167 898 reviews of repairs at TECH SERVICE in total
Нурасыл М.Order No. ZK-8825 · 6 December 2025
oursНужен был ремонт спутникового ресивера — обратился сюда. Симптом был очевидный: зависает. Дамир М подсказал, как продлить жизнь технике. Поставили новую деталь: тюнер. Приехал без записи, приняли как есть. Оплатил картой, чек дали. Даже настройки не сбились, что удивительно.
Тимур И.Order No. ZK-2024/262 · 29 October 2024
oursДо этого обращался в другой сервис, там только развели руками. Диагностика телевизора — с этого всё началось. Основная жалоба — не включается. Деталь на замену — матрица. Сравнивал с двумя другими — здесь вышло ровнее всех. Объяснили по телефону, что можно не везти, но я всё равно привёз. Срок сдвинулся на день, но без последствий. Сказать, что доволен — ничего не сказать.
Марина В.Order No. ZK-8373 · 28 June 2024
oursХотел сначала вызвать мастера на дом, потом передумал. Симптом был очевидный: зависает. Проверили на всех режимах, всё чётко.
Гаухар Н.Order No. TS-3762 · 8 February 2022
oursПробовал найти мастера в своём районе, но все были заняты. Основная жалоба — зависает. Сделали и забыл про проблему.
Серик М.Order No. ZK-2020/111 · 23 October 2020
oursҰзақ уақыт бойы жөндеуге беретін жер іздедім. Бөлшектің бар-жоғын бірден тексерді, қоймада бар екен. Алдын ала айтқан уақыттан ерте бітірді. Бағасын алдын ала келістік, соңында өзгерген жоқ. Жұмыс барысын көрсетіп отырды, жасырған жоқ. Ескі бөлшекті қайтарып берді, әдетте олай жасамайды. Ұсынамын, текке ақша алмайды.
Дмитрий Л.Order No. 520995 · 12 June 2020
oursДруг посоветовал, у него похожая история была. Жалоба простая: слетела прошивка. Второй месяц — полёт нормальный.
Камила А.Order No. ZK-2019/775 · 24 November 2019
oursҚарапайым ғана ақау деп ойладым, бірақ басқаша болып шықты. Кепілдік берді, бұл мен үшін маңызды. Диагностика тегін болды, бұл жағы жақсы. Бағасын алдын ала келістік, соңында өзгерген жоқ. Мастер ақауды түсіндірді, қажетсіз нәрсе таңбады. Ескі бөлшекті қайтарып берді, әдетте олай жасамайды. Бәрі жақсы, шағымаймын
Ляззат К.Order No. ZK-2019/786 · 16 May 2019
oursЯ человек терпеливый, но тут уже думал всё. Основная жалоба — не включается. Сделали аккуратно, следов разборки не видно.
Александра Н.Order No. 2018-7742 · 31 December 2018
oursРаботаю допоздна, поэтому нужен был сервис с нормальным графиком. Проверили на всех режимах, всё чётко.
Нурасыл М.Order No. TS-1701-421 · 16 November 2017
oursПробовал найти мастера в своём районе, но все были заняты. Диагностика спутникового ресивера — с этого всё началось. Проблема — зависает. Отдельно спасибо мастеру — Дамир М, терпения ему хватило. Позвонили заранее, предупредили, что задержится на полчаса. Могли бы взять больше, но взяли по-божески. В списке работ — тюнер. Техсервис на Абая, если не ошибаюсь, — вот туда и поехал. Сделали аккуратно, следов разборки не видно.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionIt's worth inspecting the casing: signs of opening along the seams, broken seals, misaligned gaps, or scuff marks on the screws all point to previous tampering. Another sign is non-original parts inside and traces of soldering, which a technician will see when taking it apart.
Yes, the backlight can be replaced separately from the matrix if the panel itself is intact. The technician disassembles the screen and installs new LED strips; whether it's possible depends on the model and design of the TV.
Most often this points to a faulty backlight or T-CON board, and less often to a matrix problem. Free diagnostics will pinpoint the exact cause: the technician will check the components and tell you what needs repairing.
Yes, we repair TCL TVs at your home: a technician arrives within 60 minutes anywhere in the city. Some faults are fixed on the spot, while complex matrix issues require repair at the service center.
Stripes usually signal degradation of the matrix or ribbon cables, and without repair the defect can progress to a complete loss of picture. Early diagnostics increase the chances of getting by with a replacement ribbon cable or board rather than the entire screen.
Most likely the problem is with the remote itself: dead batteries, dirty contacts, or a faulty IR transmitter. Try replacing the batteries and wiping the window; if that doesn't help, the technician will check the signal receiver on the TV.
Tech Service repairs TCL TVs in Almaty as a direct contractor: our technician comes to your home within 60 minutes or takes the TV to our service center. Diagnostics are free, we agree on the cause and scope of work before repair, and we provide a 1-year warranty on labor and parts. Our technicians have 4 to 20 years of experience.
In this brand's equipment, it's not that 'everything fails at once' — specific components break: backlight, power supply, signal processing board. Let's look at the signs that tell the owner it's time to call a technician, and what each symptom means.
We read the TCL indicator blink as a code: the number of flashes in a series points to the faulty unit — power supply, backlight driver, or MainBoard. The series repeats with a pause, and by its length the technician narrows down the checks even before opening the case. Models on Google TV and Roku TV have different code sets, so state the model right when you call. TCL TV repair in Almaty starts with decoding this series: the indicator blinks according to an algorithm flashed into the board, and repeatability is the main clue. Count the flashes at the moment you turn on the TV, not after: during a restart, the count gets messed up if the power supply capacitors are already partially discharged. The technician records the length of the series and pauses on video — so the code isn't lost during repeated attempts.
Most often in this case, the LED backlight or its driver fails in TCL TVs, while the matrix and MainBoard remain working. The backlight consists of strips and bars with a driver: one LED burns out — and the whole chain goes dark, even though sound and menu keep working. A bright flashlight pointed at the screen in a dark room helps test the hypothesis in a minute. If you can make out a picture on the panel under such light, it confirms the backlight, and restoration doesn't require replacing the matrix. In our practice, most such calls are resolved by replacing strips and bars without removing the panel — and therefore without the risk of damaging the matrix itself during disassembly. We provide diagnostics free of charge, so testing the hypothesis adds no cost.
Lines and dark areas on TCL TVs come from three different units — the matrix, the ribbon cable, or the T-CON, and you can tell them apart by how the picture behaves. Ribbon cables and connectors are checked first: oxidation or a shifted contact causes even vertical lines. The T-CON is responsible for scanning, and its failure shows up as a chaotic grid or half the screen. Lines that are visible both in the menu and on all signal sources usually point to the panel or T-CON, while lines on only one input point to the cable or the set-top box. Darkening in the corners and spots in the center are usually linked to local backlight degradation, not the matrix, so technicians in the city start by checking the uniformity of the glow.
TCL produces LED, QLED, Mini LED, and OLED lines on different platforms. Let's look at how these designs differ for a technician and why there's no universal approach to disassembly and diagnostics here.
| Line | How the backlight is designed | What disassembly affects |
|---|---|---|
| LED | strips along the edge or at the back | simple disassembly, frequent strip replacement |
| QLED | LEDs plus a quantum dot layer | protect the layer when removing the panel |
| Mini LED | many small diodes with dimming zones | many zones, careful disassembly |
| OLED | organic pixels without backlight | separate approach, complex panel |
On our platform, the firmware affects the boot behavior: Google TV and Roku TV restart and hang on the logo differently. On Google TV, the issue more often shows up as a reboot loop after an update, while on Roku TV it gets stuck on the start screen and stops responding to the remote. Firmware comes first here: we check the version, try a reset and reflash, and only then look at the MainBoard. Hanging on the splash screen doesn't always mean a hardware failure—we check the firmware first and only then go to the MainBoard. In our experience, some Smart TV calls for Google TV and Roku TV are resolved at the software level without replacing the board, so don't write off the TV because of one stuck logo. If you need TLC TV repair in Almaty, the technician will handle both the firmware and the board.
We replace the TCL backlight without replacing the matrix—it's a separate unit, and if the panel is working, replacing it restores the picture. The strips sit behind the matrix and aren't structurally connected to it: if there's darkening, spots, or even glow around the edges, they're to blame, not the panel itself. We replace them as a set because the LEDs in the strips age at the same time, and spot soldering only postpones the next failure. The backlight is replaced as a set of strips, not individual LEDs, otherwise another strip will fail before long. We remove the matrix carefully and put it back—it stays original, and the 1-year warranty on labor and parts covers the new backlight set. Before disassembly, the technician checks the integrity of the panel's ribbon cables: a damaged cable can't be restored after removing the matrix, and then you'd have to replace the whole unit instead of just the backlight.
Our diagnostics go from simple to complex—from the indicator code and checking the source to disassembly and testing components. Below we show how this works in practice.
We decode the TCL indicator blinking as an error code: a series of flashes narrows it down to the power supply, backlight driver, or MainBoard before disassembly. We count the number of flashes in the pause between series and compare with the table for the specific model line—the set of codes differs for Google TV and Roku TV models. Then we check the output voltage of the power supply, the driver's response to load, and the presence of a signal from the MainBoard. The code doesn't replace testing but sets the order: first we check the unit it points to, and only then move further along the circuit. Moreover, a series of three flashes more often points to the backlight, while continuous blinking points to the power supply, and this saves time during disassembly.
We check in sequence: the backlight by the glow behind the panel, the board by its response to sources, the matrix and ribbon cable by the behavior of stripes in the menu. In a darkened room, we shine a flashlight on the screen: if a faint image is visible, the LED backlight is partially alive, and the picture is gone due to the driver or a broken strip. We check the MainBoard by switching inputs and the appearance of the menu—response to the remote with a black screen indicates the backlight, not the board. The ribbon cable connects the T-CON and the matrix, so we inspect its contacts for creases and oxidation, and the connector for tight fit. Stripes that change when pressing on the frame often indicate the ribbon cable, while fixed ones indicate the panel or T-CON. This sequence eliminates unnecessary disassembly: replacing the ribbon cable is cheaper and faster than finding a panel, and it's worth starting with that.
After a power surge, TCL TVs most often suffer damage to the power supply, less often to the MainBoard and backlight driver, while the panel usually remains intact. The impulse travels through the input circuit, blows the varistor and converter switches, so the TV goes into protection or shows no signs of life. If the unit turns on but shuts down after warming up, this indicates a component that goes into protection when heated, rather than an immediate failure. Testing the power supply diodes and capacitors shows what needs replacement and what holds up under load. Moreover, the fuse in this circuit is often intact—it is rated for a different threshold, while the switches and PWM controller are what fail. In this scenario, the panel almost never suffers: it is powered by a separate low-voltage circuit, and the surge rarely reaches it. Therefore, after a pulse, we start checking the input power stage, not the matrix.
The question "fix or replace" for TCL is decided not by price but by the type of failure, age, and panel class. Below are the criteria that make this clear even before opening the case.
We consider this approach justified when the failure involves the backlight, power supply, or MainBoard, and the panel itself is intact. These are components that can be restored without replacing the matrix: LED strips are replaced as a separate set, the power supply as a whole board, the MainBoard by resoldering failed elements or replacing the module. The age and class of the panel matter more here than the fault itself. The newer and higher the class of the screen, the more sense it makes to invest in restoration: Mini LED and QLED lose value more when replaced than a basic LED model, and the difference between restoration and buying a new unit becomes more noticeable. In our practice, units with a working matrix and live picture return to normal operation after replacing the backlight or board and do not require repeat intervention. Before deciding, consider how long the rest of the electronics will last—if the board and matrix show no signs of overheating, restoring the component extends the life of the entire unit.
If the matrix itself is damaged rather than the backlight, panel replacement is often not justified—it is the most expensive component in the TV. The matrix is controlled by the T-CON board via ribbon cables, and its replacement involves the entire assembly, not a separate layer. A crack or impact on the screen appears as lines radiating from the point of impact: the defect cannot be fixed by restoring the backlight because the liquid crystal layer itself is damaged, not the light source behind it. Darkening at the edges, vertical stripes, and rainbow spots without an impact point are a different story: they should be checked for backlight and ribbon cable issues before writing off the panel. The owner should distinguish between these two scenarios: one thing when part of the screen goes dark due to a strip, and quite another—a mechanical chip in the glass.
We agree on the cause and scope of work before any intervention, so the TCL owner decides "fix or replace" after a free diagnostics, not blindly. The technician comes to your home, opens the case, and shows which component failed: backlight, power supply, MainBoard, or panel. He quotes the cost of work after diagnostics, once the cause is confirmed—before that, naming a sum would be guesswork. The decision remains with the owner: we do not start work without approval, and a 1-year warranty on labor and parts applies to everything restored. Our experience—from 4 to 20 years across different panel classes—tells us in which cases component restoration gives a stable result and in which replacing the unit is more reasonable. This procedure removes the main fear—that work will be done blindly and you'll be billed for something that wasn't needed.
Some issues can be resolved on the spot without a call, and the rest depends on how quickly the technician arrives and where the repair takes place. Let's go over the checklist and the work order.
Our mobile technician arrives at your home within 60 minutes anywhere in the city, or we take the TV to the service center if the work requires workshop conditions. Diagnostics are free: we check the power, boards, and backlight on site, then tell you the cause and the cost of repairs. Board repairs and adjustments are usually done at home — no need to disassemble the panel. Panel work, where the matrix has to be removed and laid flat, is better done at the service center: there the TV can be placed on a level surface without risking the screen in a cramped room. The Tech Service technician decides which format suits the specific breakdown — that determines whether the unit is taken away or fixed on the spot. We start TV repairs in Almaty with this decision because it affects both the time and the safety of the panel.
We provide a 1-year warranty on labor and parts, check the result after repair, and you can pay via Kaspi QR, Kaspi Red (instalments), bank card, cash, or bank transfer for companies. After reassembly, the TV is turned on, the picture is checked on different inputs, and we show that the defect is gone. The warranty also covers the part, so if the same unit fails again, the repair is done under warranty, not charged anew. Payment is made after you see the result — and the price is quoted during the free diagnostics, before work begins. If the same issue reappears within a year, we repair that unit again at no extra charge — that's the point of a parts warranty, not just coverage of the technician's work.
The collected symptoms add up to a clear picture: they show what to check first and when restoring the device stops being reasonable.
63brands
We work with TVs of every brand sold in Kazakhstan — from Samsung, LG and Sony to Artel, Yasin, Kivi, Hyundai, Thomson and rare makes. Can’t find yours? Call anyway — a technician will come and take a look.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your TV won't turn on, first check the outlet, power cable, and the button on the TV itself—not the remote.
21 November 2025 · 12 minutes read
If your laptop screen is broken, turn the device off first, don't press on the display, and check the picture through an external monitor.
12 March 2026 · 11 minutes read
If your phone won't charge, start by checking the adapter, cable, and port, then the charging settings.
16 February 2026 · 12 minutes read
If your laptop freezes, the first thing to do is restart it and check Task Manager to see what's loading the CPU and memory.
25 January 2026 · 12 minutes read
If your phone falls in water, take it out right away, turn it off, and don't charge it.
19 January 2026 · 12 minutes read
If your phone camera isn't working, first check app permissions, clear the cache, and restart your phone — this fixes some software glitches.
24 December 2025 · 13 minutes read












