experience10 yearsVasiliy Z.
Senior TV repair technician
City
Language
What broke
Sections
Message on WhatsApp+7 (778) 021 13 16Mon–Fri 10:00–19:00, Sat–Sun 11:00–18:00
A technician arrives within 60 minutes anywhere in the city. Free diagnostics, 1-year warranty on labor and parts.
Our own technicians4 to 20 years of experience




Repair prices
Select the symptom that matches your TV's behavior — likely components are described under each.
power supply failure, board fault
from8 000 ₸
backlight or inverter failure
from7 000 ₸
speaker or amplifier failure
from8 000 ₸
dead batteries, receiver failure
from9 500 ₸
overheating, power supply fault
from9 000 ₸
panel or ribbon cable failure
from8 000 ₸
antenna or cable issues
from7 000 ₸
power supply or backlight failure
from3 500 ₸
The table lists the 'from' price for labor, for common jobs also the 'from' price of the part, plus the time required to complete the job.
1 visittime
from 9 000 ₸cost

BeforeAfter5 steps

From request to check — five steps.
Leave a request by phone or messenger and describe the symptom.
A technician will arrive anywhere in the city within 60 minutes after confirmation.
The technician will inspect the TV and name the cause and repair cost.
You approve the cost and scope of work, then the technician starts.
Turn on the TV, check the picture and sound, and make sure the symptom is gone.
The digital device repair department in Almaty has 7 technicians with 7 to 18 years of experience.

The department has 7 specializations — they are listed on the technicians' cards.
experience10 yearsSenior TV repair technician
experience10 yearsTV board repair technician
experience10 yearsElectromechanical technician
experience13 yearsAudio and DVD repair technician
experience18 yearsSmartphone repair technician
We reply during working hours
Leave a request — the technician will agree on a convenient time and name the cause after inspection.

Warranty question? Call us
+7 (778) 021 13 167 898 reviews of repairs at TECH SERVICE in total
Ольга М.Order No. ZK-2025/212 · 30 October 2025
oursИскал мастерскую поближе к дому, чтобы не мотаться с техникой через полгорода. Оставил заявку на ремонт телевизора. Основная жалоба — полосы. Поменяли: подсветка. Даже с учётом запчасти вышло гуманно. Приехал без записи, приняли как есть. Ставлю пятёрку. Функции все на месте, ничего не отвалилось.
Талгат С.Order No. 279409 · 27 January 2025
oursХотел сначала вызвать мастера на дом, потом передумал. Заметил случайно: зависает. Отдельно спосибо мастеру — Дамир М, терпения ему хватило. В списке работ — тюнер. Сравнивал с двумя другими — здесь вышло ровнее всех. Мастер приехал на дом, всё посмотрел при мне. С чистой совестью советую. Включил, проверил, работает.
Арман К.Order No. 24516 · 26 May 2024
oursРаботаю допоздна, поэтому нужен был сервис с нормальным графиком. Нужна была замена: блок питания. Вернули в тот же день, всё функционирует.
Аружан К.Order No. 2023-6141 · 13 June 2023
oursПозвонил в три места, здесь единственные назвали цену сразу. Заодно поменяли: блок питания. Внешне как новый, если не считать мелкой царапины
Елена К.Order No. 35048 · 11 May 2023
oursОсновная жалоба — нет сигнала. Дамир М снял деталь, показал износ, вопросов не осталось. Внешне как новый, если не считать мелкой царапины.
Марат Ж.Order No. TS-2308-732 · 3 March 2023
oursЖұмыстан кейін үлгеру үшін жақын жердегі шеберхана іздедім. Бұрын осында ноутбук жөндеткенмін, сондықтан сеніммен келдім. Достарыма да айттым
Дмитрий Л.Order No. 32621 · 5 August 2020
oursПробовал найти мастера в своём районе, но все были заняты. Прошивку не тронули, всё как было.
Виктор Ф.Order No. 2019-6970 · 21 August 2019
oursБыло важно, чтобы сделали до выходных — гости, то-сё. Повод для визита: не включается. Работает как раньше, придирок нет.
Санжар О.Order No. TS-5677 · 24 May 2019
oursПервое, что заметил: слетела прошивка. Функции все на месте, ничего не отвалилось.
Марина В.Order No. ZK-6032 · 24 December 2016
oursС чем пришёл: не включается. Отдельно спасибо мастеру — Дамир М, терпения ему хватило. Пользуюсь ежедневно, вопросов нет.
Didn’t find the answer? Message us on WhatsApp.
Ask a questionYes, it's often possible: a hit usually damages the panel, ribbon cables, or mounts, and a technician determines what can be restored. A free diagnostic will show what exactly was damaged, and a lot depends on the model.
Leave a request on the website or give us a call — a technician will come to your home in Almaty and run a free diagnostic. They will identify the cause of the breakdown and tell you what needs fixing.
Most often, stripes are caused by ribbon cables or the board, not the panel itself, and this can be fixed with repair. A conclusion about replacing the screen is made only after a free diagnostic, and it depends on the model.
Usually no: to reach the backlight, the panel has to be removed and disassembled. It depends on the model, but this work is typically done at the service center, not on the wall.
It's better not to keep using it: a faulty backlight puts stress on the power supply, and over time more components may fail. It's best to have a technician look at the TV to avoid needing to replace expensive parts.
Yes, it's better not to delay: such issues often come from the power supply or overheating, and over time they can damage other components. A technician will find the cause during a free diagnostic and tell you what needs fixing.
Tech Service repairs JVC TVs in Almaty: our technician arrives at your home within 60 minutes or picks up the TV for service. Diagnostics are free, we provide a 1-year warranty on labor and parts, and we quote the price after diagnostics. Technicians with 4 to 20 years of experience work on JVC plasma, LED, and Smart TVs.
On JVC panels, the indicator is the first diagnostic signal: by the number of flashes, the TV reports which unit it considers faulty. Here's what the flash series mean and which symptoms owners most often report.
On JVC TVs, a blinking red indicator is a self-diagnostic code: the number of flashes in a series points to the unit that the electronics consider faulty, so the technician starts by counting the series, not by taking the TV apart. The controller monitors the power supply startup, the motherboard response, and the backlight circuits; if one of these units fails to reach operating mode, the indicator gives rhythmic flashes instead of a steady light. From these, the specialist narrows down the search: power source, main board, or backlight circuit. You need to count the series with pauses, not all flashes in a row—the rhythm helps the electronics separate one error from another. If the panel won't start, JVC TV repair in Almaty begins with decoding the flash code and measuring at the units. A steady light followed by shutdown means something else: the board completed startup but protection cut power due to parameter deviation, and then the technician looks not at the code but at the condition of secondary circuits and the temperature of key components.
In our diagnostics, the same symptom "no picture" is checked along the chain of power source, backlight, and T-CON, because externally these faults look identical. The power supply provides voltages, the LED backlight illuminates the matrix, and the processing board builds the image from the signal on the LCD panel—a failure at any stage results in a black screen. The technician measures voltages, checks the backlight and signal on the processing board, and only then names the culprit. Guessing the unit by eye leads to replacing a working part, so the chain is checked from power source to picture, not the other way around. Hence the rule: first measurements, then verdict—this way diagnostics take less time, and the owner doesn't pay for an extra part.
We break down the JVC units that fail most often and the technician's actions in each case—from power supply to matrix.
| Component | Typical symptom | Check area | Service format |
|---|---|---|---|
| Power supply | won't turn on, indicator blinking | output voltages | on-site or in workshop |
| LED backlight | dark screen, spots | strip illumination | usually in workshop |
| T-CON board | stripes, image distortion | signal to matrix | on-site or in workshop |
| LCD matrix | no image but sound works | panel integrity | diagnostics only |
| HDMI and USB | source not detected | port contacts | on-site |
| Audio path | no sound | speakers and board | on-site |
Our on-site inspection is free: a technician arrives within 60 minutes, checks the power supply, backlight, and boards based on symptoms and the number of blinks, then names the cause and the cost. For a blinking indicator, we count the series of flashes — it narrows things down to the power supply or control board, and a tester on the outputs confirms which line has dropped. We check the backlight by how evenly the strips glow, and the T-CON by whether the signal reaches the matrix. Some faults only become visible after partial disassembly, so the technician immediately says what can be done on-site and what requires a bench. Ask the specialist which component they ruled out and why — it makes it clearer what you're paying for. In my experience, half of the "complex" cases come down to a single failed capacitor.
Plasma and older JVC LCD TVs are a separate story: they have their own weak spots, and the question "restore or replace" is decided by the panel's condition, not the age of the set.
We bring plasma JVC TVs back to life: most often we restore the power supply and address panel degradation, but we decide on the matrix only after disassembly and inspection. In a plasma, the image is formed by gas cells with phosphor, and power goes through several separate units — the power supply, control board, and Y-drivers. Failures most often occur in the power section: bulging capacitors, blown switches, broken solder joints on the inverter. Such faults are fixable, and after replacing the damaged components the set shows a picture again. The panel itself is trickier: in plasma, the phosphor loses brightness over time, and that can't be fixed by replacing a board. So the technician honestly says when repairs won't bring the picture back — for example, with burned-out areas or cracks in the glass, replacing components is pointless.
An old JVC is worth restoring if the power supply, backlight, or board is faulty rather than the panel itself — then the result is a working TV again. In older LCD models, the electrolytic capacitors in the power supply, the LED backlight strips, and the ribbon cables between boards are the most common failures. These components can be replaced, and the set keeps working for years. The panel is another matter: if the matrix has cracks, bright spots, or burned-out areas, restoration no longer makes sense. The decision depends on which component failed: replacing a board is usually justified, while restoring a degraded panel is not. Before writing off the TV, it's worth checking the LCD matrix for integrity and making sure the defect isn't in the backlight — that changes the conclusion about whether the work is worthwhile.
We show the step-by-step process — from request to checking the result — and explain what the technician does on site and what requires service center conditions.
At home, we most often restore the power supply, HDMI and USB ports, and the audio path, while the backlight and matrix are usually serviced in the service center, where there are conditions for disassembling the panel. The power supply is tested under load, the ports for contact and solder joints, and the audio path at the speaker output; these operations don't require removing the screen and don't take much space. LED backlight and LCD matrix are replaced only after fully disassembling the layers, and doing this at home is risky: the panel is easy to damage when moving and laying it down. Replacing the backlight requires careful work with diffusers and mounts, so such work is moved to the service center. In our experience, taking the set in for backlight repair costs less than replacing a panel broken during transport.
Yes, we also make visits for a JVC Smart TV stuck on the splash screen: the technician checks the firmware and motherboard and restores startup on site or in the service center. Being stuck on the logo doesn't always mean a software failure — sometimes the board is to blame, and trying to reflash without checking the power supply only masks the cause. First we measure the voltages at the power supply output, then check the firmware integrity and the motherboard condition. If the failure is in the software, startup is restored by reflashing; if the board is damaged, we repair or replace the component in the service center. This approach saves time and money: the owner doesn't pay for a second visit after a failed attempt to reflash the set blindly, and the cause is found on the first try.
We explain who exactly comes on a request, what the warranty covers, and what makes up the cost of JVC repair — these three points are what owners most often check before calling a service center.
We provide a 1-year warranty on labor and parts: if the same issue comes back after service, the technician will return to fix it under warranty. One year is the same term for replacing a power supply, repairing backlighting, and working on the main board, so you don't need to clarify which components are covered: labor and the installed part come as one package. In our experience, components replaced as a whole last longer than those repaired point-by-point, and the warranty period feels more reassuring on them. The warranty also covers the part itself, so the client doesn't have to figure out what failed—the soldering or the component: the technician sorts that out, not the owner. If the TV behaves differently than expected after service, record the symptom on video—it makes it easier to determine whether the case falls under warranty.
Tech Service is a direct contractor: our technician comes to you, not a subcontractor from an aggregator, so one company is responsible for diagnostics, repairs, and warranty. Our specialists have been working with JVC for 4 to 20 years, know the boards of this brand by revision, and don't waste a visit looking up instructions. When an intermediary stands between the client and the technician, warranty and responsibility get blurred: one person took the request, another did the work, and there's no one to file a claim with. With a direct contractor, the terms are the same for all requests—warranty, diagnostics, and who exactly calls you back after service. And it's clear from the moment you place a request: you're given the name of the technician, not a "specialist from the database." Ask when you call who will do the work—if the answer is vague, it's an intermediary scheme.
Our technician quotes the price after free diagnostics, when the cause and scope of work are clear, so the number isn't pulled out of thin air. Diagnostics before any intervention isn't just a formality: without it, you can't tell a cheap board replacement from expensive panel work, and the client risks overpaying for a component that's actually fine. The technician checks the power supply, backlight, main board, and the matrix itself, then explains which elements need attention and which should be left alone. You can pay via Kaspi QR, Kaspi Red, bank card, cash, or bank transfer for companies—so you choose how to pay. If the sum seems high after diagnostics, ask for a breakdown by component: that way you can see exactly which operation you're paying for.
JVC TV repair comes down to accurate diagnostics: the same symptom on different models points to different components. Below are the key takeaways to help you decide whether to repair.
63brands
We work with TVs of every brand sold in Kazakhstan — from Samsung, LG and Sony to Artel, Yasin, Kivi, Hyundai, Thomson and rare makes. Can’t find yours? Call anyway — a technician will come and take a look.
Tech Service technicians repair other appliances too — with the same 1-year warranty on labour and parts.
Refrigerator Repair in Almatyfrom 3 000 ₸
Washing Machine Repair in Almatyfrom 3 000 ₸
Dishwasher Repair in Almatyfrom 3 500 ₸
Oven Repair in Almatyfrom 3 000 ₸
Cooktop Repair in Almatyfrom 3 500 ₸
Air Conditioner Repair in Almatyfrom 3 500 ₸
Boiler and Water Heater Repair in Almatyfrom 2 500 ₸
Freezer Repair in Almatyfrom 6 000 ₸
Tumble Dryer Repair in Almatyfrom 5 000 ₸
Coffee Machine Repair in Almatyfrom 2 500 ₸
Robot Vacuum Cleaner Repair in Almatyfrom 3 500 ₸
Vacuum Cleaner Repair in Almatyfrom 1 500 ₸
Microwave Oven Repair in Almatyfrom 2 000 ₸
Hair Dryer Repair in Almatyfrom 1 500 ₸
Iron Repair in Almatyfrom 3 000 ₸
Electric Kettle Repair in Almatyfrom 2 500 ₸
Mixer Repair in Almatyfrom 2 500 ₸
Multicooker Repair in Almatyfrom 500 ₸
If your TV won't turn on, first check the outlet, power cable, and the button on the TV itself—not the remote.
21 November 2025 · 12 minutes read
If your laptop screen is broken, turn the device off first, don't press on the display, and check the picture through an external monitor.
12 March 2026 · 11 minutes read
If your phone won't charge, start by checking the adapter, cable, and port, then the charging settings.
16 February 2026 · 12 minutes read
If your laptop freezes, the first thing to do is restart it and check Task Manager to see what's loading the CPU and memory.
25 January 2026 · 12 minutes read
If your phone falls in water, take it out right away, turn it off, and don't charge it.
19 January 2026 · 12 minutes read
If your phone camera isn't working, first check app permissions, clear the cache, and restart your phone — this fixes some software glitches.
24 December 2025 · 13 minutes read












